CERTAIN SANCTIONED WORKS UNDER GE (WEST) JABALPUR

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness incl part chipping (below or above ground level) complete all as specified and directed.

Dismantling of wall tile, floor tile, dado including bedding but backing and rubbish off permises complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide and not exceeding 1.5mtr depth for foundation in soft/loose soil & getting out complete all as specified and directed.

Excavation over areas n.exc 1.5m in depth for foundation, etc or for shafts, wells exc 10 sqm on plan and getting out soft/loose soil complete all as specified and directed.

Excavation over areas exc 1.5m and n exc 3.0 m depth for foundation, soft/loose soil complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hard core, broken stone / boulders to gauge n exc 63 mm laying in layers complete all as specified and directed.

PCC (1:4:8) type D2 using 40mm graded aggegate as in foundation complete all as specified and directed.

PCC (1:5:10) type E-2 using 40mm graded stone aggregate as in foundation & mass concrete complete all as specified and directed.

Returning filling in incl spreading, levelling, watering & well ramming in layers not exc 25cm thick for soft/loose soil complete all as specified and directed.

Removing excavated material 250 m but n.exc 50m and depositing where directed at a lavel .exc 1.50 mtr above the starting point complete all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, wind ties etc. conforming Fe 410 -W (GdeE- 250) qualityA complete all as specified and directed.

M&L for Roof trusses (framed), trussed,post,rafters, purlins, tube crane, gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, wind ties etc. conforming Fe 410 -W (GdeE- 250) quality ''A'' complete all as specified and directed.

M&L MS work as in wind ties for roof including securing bolts, drilling holes, notching for wire etc complete all as specified and directed.

M&L Brick work using fly ash old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L 15 mm thick rendering on fair faces of bk /concrete surfaces in CM (1:6), finished even and smooth (without using extra cement ) complete all as specified and directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on other than fair Faces of Brick Walls or on Concrete Surfaces plastered Surfaces Finished fair and even complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate in copings, kerbs, and the like all as directed incl necessary form work complete all as specified and directed.

M&L plan cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate for coping, fixing of fencing post, hold fast etc complete all as specified and directed by Engr-in-charge

Taking down of eves gutter,rain water pipes ,AC/PVC pipes of any size or pattern including all fittings etc complete all as specified and directed.

M&L for machine cut Kota stone slab flooring, 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing (granite finish) and exposed edges of Kota stone shall be rounded including 20mm thick screed bed to floor finishes in cm 1:6 complete all as specified and directed.

M&L for 20mm thick pre polished Black (Zed Black/Brick Red) granite slab laid with 15 mm thick CM 1:4 rendering over vertical Pillers including fixing and jointing with grey cement slurry and pointed in white cement with pigment to match the shade of granite stone including Moulding/rounding and polishing all as specified and directed by Engr-in-charge

M&L 25 mm thick cement concrete (1:2:4), type B-0, (using 12.50 mm graded aggregate) as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

M&L Cement concrete (1:2:4) type B-1,using 20 mm graded stone aggregate as in flooring 150 mm thick and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for non skid ceramic coloured joint free tiles 10 mm thick area of each tile exceedeing 0.18 sqm but n.exc 0.38 sqm (600x600), in floors, set and jointed in neat cement slurry and pointed in white cement to over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

S&F, PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F, in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 75 mm bore with access door complete all as specified and directed.

S&F in repairs PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed

S&F in repairs PVC (SWR) junction single, (single T) equal or un equal of 75 mm bore of pipe complete all as specified and directed

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) n. exc 1.5 Sqm each including removing to store complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) exc 1.50 sqm but n exc 4 sqm each including removing to store complete all as specified and directed.

S & F 35 mm thick factory Made moulded glazed/gauged door with pre pressed lamination on both side, solid core construction & prepaid to receive glass/wire mesh including fixing of SS wiremesh of nominal dia 0.36 mm , 2 Nos door Aluminium handle, 0.3 Nos SS butt hing of 100mm , 2 nos Aluminium tower bolt 150mm length in each shutter complete all as specified in SSR Part I and as directed and fitted to chowkhats.

S & F 35 mm thick Factory made moulded flush door with pre pressed lamination on both side, solid core construction 2 Nos Aluminium door handle, 0.3 Nos SS butt hing of 100mm , 2 nos Aluminium tower bolt 150mm length and 300 mm length Aluminium sliding door bolt in each shutter complete all as specified in SSR Part I and as directed and fitted to chowkhats.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed.

S&F for extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

Butt hinges 100mm, medium weight, cold rolled Stainless steel, and fixed complete all as specified and directed.

S&F, Mild steel sliding door bolts 300mm size, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F mild steel, 200 mm long ordinary helical door spring incl roller and roller plate complete all as specified and directed.

S&F Floor 40-50 mm door stopper of aluminium alloy body and tongue anodised with hard steel spring ,fixed in floor complete all as specified and directed.

S&F stainless steel wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty/wooden beading in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

M & L preparation of New plastered wall surfaces and applying 2mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper over resistant priming paint complete all as specified and as directed by Engineer-in-charge.

M & L for complete removal of existing treament and preparation of old plastered wall surfaces and applying 2mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper complete all as specified .

M & L for preparation of new plastered wall surface and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over 2mm thick water proof wall care putty complete all as specified and as directed.

M&L for Complete removal of existing treatment of any description and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over and including 2mm thick water proof wall care putty complete all as specified and as directed.

M&L preparation of new plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed.

M & L preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide/Zinc Chrome primer complete all as specified and as directed.

M&L for Cutting holes in brick walls exc 1/2 brick & n exc full brick built in cement mortar for inserting hold fasts, cutting and preparation of brick wall for insertion and making good dismantled portion in cement mortar 1:3 etc complete all as specified and directed.

Mild steel TMT bars, 10 mm dia and over, cut to length, bent to shape required including cranking bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed.

M&L for MS box type section With rebate (single/double) suitable for door frame for fixing of door shutter etc complete as specified and directed.

M&L for anodized aluminium powder coated (minimum thickness of powder coating 50 micron) three track sliding window, frame side top and sides of size 92x31.75x1.5 mm (Section No. 20831), bottom size 92x31.75x1.5 mm (Section No. 20832) and shutter top and bottom size 40x18x1.55 mm (Section No. 20736) and sides (handle) of size 40x18x1.55 mm (Section No. 20738) and lock side shutter frame of size 40x18x1.55 mm (Section No. 20737) including rubber gasket, beading and locking arrangement including making good the disturbed portion complete including stainless steel wire staples and including fixing 5 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting, cill and making good to disturbed portion complete all as specified and directed. ( Note : Glazing is deemed to be included in the quoted rate of contractor and will not be paid for separately. )

M&L 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in floor sub base and finished even and fair complete all as specified and directed.

Dismantling of plain/ corrugated AC sheeting, any gauge, thickness, incl nainital or similar pattern roof covering complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding/ ridge to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of timber scantlings unframed 40Sq Cm and over in section, in any position complete all as specified and directed.

S&F steel work in tubular trushes including special shaped washer etc complete using ERW or induction but welded tubes confirming to I.S. 1161-1979 grade St. 240 etc complete all as specified and directed.

M&L, Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates ,rails,braces etc complete drilled for fixing of steel gate sheeting or other covering,doors ,etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering ,runing rails and guides ) and hanging also fastning and fixing complete all as specified and directed. confirming to FE-2990 ( Gde E-165).

S&F framed work as in doors or gates of angle or other section with gussest plates, door frame ,shutter,sheet rails, braces, etc, complete drilled for fixing of steel sheeting or other covering doors etc, to be prepared for hanging and sliding with and including either hooks and hinges or steel hnging door fittings and fixing complete confirming to gde Fe 410 (Gde E-250)

S & F framed work such as grills, gratings, drain cover etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S & F for Framed work such as Gate, grills, gratings, with ornamental & intricate design for spikes etc., with ends of bar shoulder &/or riveted, or forged into spikes; incl hinges & similar work conforming to Fe 290 GDE -E-165 complete all as specified and as directed.

S & F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre in level and fixed in required position complete all as specified and as directed.

Demolition of wall and ceiling boards any type (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M & L for snap grid false ceiling system of E board exposed suspended system, grid size 600mm x 600mm compressing of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), and fixed with pre painted 4mm thick E board of approved design and with provn of light fixture complete all as per manufacturer instructions and as directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in CM 1:6 for laying floor finish complete all as specified and all as direcred.

S & F Aluminium powder coated (minimum thickness of powder coating 50 micron) Ventilator louvers type frame top and sides of size 31x42x1.6 mm ( Section No 20558) rectangular tube of size 40x20x2.0mm ( Section No 14019) and middle vertical of size 42x46.20x1.60mm ( section No 20560) and clip for fixing in wiremesh and glass of size 19x17.30x0.90mm ( section No 19360) including rubber gasket, beading, anodised aluminium snap beading, screws, handle,fixing 4.00 mm thick glass frosted glass , 0.36 mm nominal dia wiremesh with necessary rubber beading gasket, Louvers plate etc for Ventilator etc including necessary plaster, painting ,cill and making good to disturbed portion complete all as specified and directed.

S&F WPV Solid door frame of size 50mm x 100 mm made of approved texture / design of density 650 kg/Cum all as per manufacturer designwith single rebated and fixed in opening as per specifications complete all as specified and as directed.

S & F 24 mm thick Factory made WPC board flush door shutter of approved texture/ design shutter complete all as specified in and as directed

Taking down carefully any type of old unserviceable point wiring (light, fan, socket bell or power) , complete with fittings such as switches ceiling roses, lamp holders sockets, regulators with PVC conduit surface /concealed or wooden patterns including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

Taking down carefully the ceiling fan/Exhaust fan of any sweep and size depositing to MES store and hanging only ceiling fan (M.D supply) and connecting complete all as specified and directed.

Taking down carefully Main switch and Distribution boards any make and size complete all as specified and as directed .

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/ PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 6.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting, fixing accessories and 4 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 6.0 Sqmm Wire and One No of 6 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket point controlled by one switch on same board.

(d) One socket point controlled by one switch on Independent board.

All as described in serial at sl No 87 - here-in-before, but with 1100 volts grade copper standard conductor FRLSH cable of size 2.5 Sqmm with 1.5 Sqmm solid copper conductor cable for 3 pin 15 Amp switch socket outlet independent board complete all as specified and directed.

M&L for fan regulator socket type AC 230 volts complete all as specified and as directed by Engineer in charge.

S&F in repairs for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and as directed .

M&L for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and as directed .

M&L for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and as directed .

M&L for switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and as directed.

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge.

S & F in repairs Smart bright Batten Series, LED luminaire using LEDs 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.

S&F in repair sheet metal enclosure DBs single pole and neutral 8 way with 200 Amps rated bus bar 240 vots single pole and neutral complete double door complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S&F MCB in replacement single pole and neutral 240 volts 40 Amps, B Series complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply & fix in replacement of LED Security Light Luminaire 35 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2 core 16 Sqmm complete all as specified and directed by Engineer in charge

S&F in repair LED light fitting square 57x57 CM not less than 36 watt alongwith fixture recessed mounting LED luminaries with diffuser channel Luminaires ers, connector block etc. complete with all accessories internally prewired and including round wood block, connecting up with three core flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge.

Supply and lay DWC pipe 38mm ID 63m OD complete all as specified and as directed.