REPAIR TO HARDSTANDING, DRAINAGE, FENCING PATH ETC AND CONNECTED ITEM AT BD BARI MIL STN UNDER GE KALUCH

Amount

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out, returning, filling and ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm watering and removing surplus soil to a distance not exc. 50 m and making good surface as in hard / dense soil complete all as specified and directed.

M & L for Providing reinforced cement concrete type B-l, 1:2:4 (20 mm graded aggregate) in precast posts, fencing posts, straining or terminal posts, struts etc. for fencing, average sectional area n exc 100 sq. cm, with or without chamfered angles and flat, splayed, rounded or mitred tops as directed and fixedcomplete all as specified and directed.

M & L for providing 50 mm thick pre-cast cement concrete louvers or RCC Jali made out of cement concrete 1:2:4 type B-0, using 12.5 mm graded stone aggregate and set in cement mortar 1:4 including all mouldings etc. complete all as specified and directed.

M & L for providing plain cement concrete, type C-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for cement concrete 1:2:4 type B-2, using 40 mm graded stone aggregate as in surface channel or drain complete all as specified and directed.

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as in benching,water throughts etc and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix),as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate, as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 (Design Mix), using 20 mm graded stone aggregate, as in columns, pillars, piers, posts, struts and the like complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks (EXCEPT BRICKS) straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed. NOTE: - OLD BRICKS OBTAINED FROM DEMOLITION SHALL BE USED UNDER THIS ITEM.

M & L for form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar works in rough finished flat surface of concrete complete all as specified and directed..

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in fair finished surface of concrete complete all as specified and directed.

M & L form work to sides of pillars, posts, struts, piers, columns and stanchions in fair finished surface of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacer and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

Supply only Chain link MS galvanisd fencing, any size or type weight n. exc 4.00 kg per sqm complete all as specified and directed.

S & F of rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging or steel hanging door fitting and also fastening complete all as specified and directed.

S & F of mild steel framed work such as gate grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F of mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexagonal or square nut, not exc. 5 cm long and 11 to 15 mm dia of neck complete all as specified and directed.

M & L for 100 mm thick PCC 1:3:6, nominal mix, type C2, using 40mm graded crushed stone aggregate as in sub base of floor, hard standing, path, pavings etc, surface finished even and smooth without using extra cement, laid in alternate bays, complete all as specified & directed..

M & L for 75 mm thick cement concrete 1:4:8 type D-2, using 40 mm graded stone aggregate as in sub base floor complete all as specified and directed.

M & L for precast designer coloured heavy duty full body paving tiles (factory made) of size 300mmx300mm x 10mm, top layer glazed made in any type of cement and pigment, in required patterns as approved by GE in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 10mm thick screed layer in cement mortar 1:4, complete all as specified & directed.

Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extra cement)complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth with neru finish to plaster work complete all as specified and directed.

M & L for complete removal of old finishes from walls by scrapping, rubbing down, with sand paper to have even and smooth surfaces and applying two coats of ‘Apex’ of Asian paint or ‘Weather coat’ of Berger Paints over one coat of primer using mechanical vaccume machine complete all as specified and directed. NOTE:-Preparation of surfaces and external weather proof paint to be carried out Mechanically

M&L for preparing newly plastered or previously untreated wall surfaces. and applying two coats of ‘Apex’ of Asian paint or ‘Weather coat’ of Berger Paints over one coat of primer using mechanical vaccume machine complete all as specified and directed. NOTE:-Preparation of surfaces and external weather proof paint to be carried out Mechanically

M & L for preparation of steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint (any tint/shade) complete all as specified and directed

S & F of 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to wall /floor complete all as specified and directed.

M& L for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound , Grade ‘A’ complete all as specified and directed.

KAMAL CONSTRUCTION

M/S SUDAGAR MAL

Balwant kumar and bros

M/s Mohammad Shafi Malik

GENESIS INDIA

M/s K.S. Constructions