Repair and renovation of Toilets (Ladies and Gents) at Local Bus Stand Sector 17, Chandigarh

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. DSR 2.8

All kinds of soil. DSR 2.8.1

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : DSR 2.10

All kinds of soil DSR 2.10.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia metre DSR 2.10.1.2

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) DSR 4.1.3

1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) DSR 4.1.10

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). DSR 5.3

Centering and shuttering including strutting, propping etc. and removal of form for : DSR 5.9

Suspended floors, roofs, landings, balconies and access platform DSR 5.9.3

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. DSR 5.22

Thermo-Mechanically Treated bars DSR 5.22.6

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: DSR 6.1

Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.1.1

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and size in : DSR 6.4

Cement mortar 1:4 (1 cement : 4 coarse sand plateform of tank DSR 6.4.1

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. DSR 8.2

Granite stone slab colour black, Cherry/Ruby red DSR 8.2.2

Area of slab upto 0.50 sqm DSR 8.2.2.1

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Size 600x300mm) DSR 8.31

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. DSR 9.20

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. DSR 9.20.1

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete DSR 9.97

250x10 mm DSR 9.97.2

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : DSR 9.100

125 mm DSR 9.100.1

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from ommercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: DSR 10.14

Profile B DSR 10.14.1

Fixing with adjustable lugs with split end tail to each jamb DSR 10.14.1.1

12 mm cement plaster of mix DSR 13.4

1:4 (1 cement: 4 fine sand) DSR 13.4.1

Demolishing Cement concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineerin-charge. DSR 15.2

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) DSR 15.2.1

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : DSR 15.12

Of area 3 sq. metres and below DSR 15.12.1

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead DSR 15.25

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : DSR 15.44

15 mm to 40 mm nominal bore DSR 15.44.1

Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge: DSR 15.45

Up to 150 mm diameter DSR 15.45.1

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. DSR 15.60

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : DSR 17.3

W.C. pan with ISI marked white solid plastic seat and lid DSR 17.3.1

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. DSR 17.16A

Providing and fixing soil, waste and vent pipes DSR 17.35

100 mm dia DSR 17.35.1

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 DSR 17.35.1.2

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. DSR 17.38

Sand cast iron S&S as per IS - 3989 DSR 17.38.1.2

Providing and fixing heel rest sanitary bend DSR 17.40

100 mm dia DSR 17.40.1

Sand cast iron S&S as per IS - 3989 DSR 17.40.1.2

Providing and fixing collar : DSR 17.57

100 mm DSR 17.57.1

Sand cast iron S&S as per IS - 3989 DSR 17.57.1.2

Providing and fixing white vitreous china water closet squatting pan (Indian type) DSR 17.13

Orissa pattern W.C. pan of size 580x440 mm DSR 17.13.2

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. DSR 17.19

10 litre (full flush) capacity-white DSR 17.19.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete DSR 17.28

Flexible pipe DSR 17.28.2

32 mm dia DSR 17.28.2.1

Providing and fixing of drip seal joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter:

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost ofcutting and making good the walls and floors DSR 17.60

100 mm inlet and 100 mm outlet DSR 17.60.1

Sand cast iron S&S as per IS: 3989 DSR 17.60.1.1

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms. DSR 17.75

Providing and fixing PTMT urinal cock of approved quality and colour. DSR 17.76

15 mm nominal bore, 80 mm long. 42 mm high and 30 mm wide with BSP female threads weighing not less than 48 gms. DSR 17.76.1

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. (EXPOSED) DSR 18.1

25 mm dia nominal bore DSR 18.10.3

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anticorrosive bitumastic paint, cutting chases and making good the wall: DSR 18.11

15 mm dia. nominal bore DSR 18.11.1

20 mm dia. nominal bore DSR 18.11.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality DSR 18.17

25 mm Nominal bore DSR 18.17.1

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : DSR 18.18

25 mm nominal bore DSR 18.18.3

Providing and fixing uplasticised PVC connection pipe with brass unions : DSR 18.21

30 cm length DSR 18.21.1

15 mm nominal bore DSR 18.21.1.1

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) DSR 18.46

25 mm nominal bore DSR 18.46.3

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR 18.48

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. DSR 18.53A

Providing and fixing PTMT bib cock of approved quality and colour. DSR 18.54

15mm nominal bore, 86 mm long. Weighing not less than 88 gms. DSR 18.54.1

Providing and fixing PTMT stop cock of approved quality and colour. DSR 18.55

15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. DSR 18.55.1

Providing and fixing PTMT pillar cock of approved quality and colour . DSR 18.56

15mm nominal bore, 107 mm long. Weighing not less than 110 gms. DSR 18.56.1

Cutting holes up to 30x30 cm in walls including making good the same DSR 18.76

With common burnt clay F.P.S. (non modular) brick DSR 18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. DSR 18.77

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: DSR 19.4

100x100 mm size P type DSR 19.4.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.4.1.1

Providing and fixing GI Tank nipple complete in all respect

Const. of curb with C.C. 1:2:4 alongwith upto 1’-0” depth to make it water proof including Cost of sand, bajri

Dismantling of floor tiles and wall tiles complete in all respect.

Providing the fixing of CP long bend 32mm I/D for cistern complete in all respect as per entire satisfaction and approval of make by EIC.

Providing and fixing of white vitreous chinaware urinal partitions of size 90x320x720 mm complete in all respect Make M-cera S4090101

Providing and fixing of CP Brass/SS/ABS Soap Tray made of Plastic including glass bowl of approved make Jal Model No. 36540 or equialent Model of CERA /Kerovit/ ESSCO

Providing and fixing of HCI P trap 4" dia complete in all respect as per entire satisfaction and approval of make by EIC.

Supplying and fixing in position pre-cast RCC/SFRC Cover with frame of quality MD-10 and size 450mm

Supplying and fixing of RCC/SFRC Cover with frame for Gully Trap Complete of Approved make

Providing and fixing of Chinaware Half stall Urinal with fittings, standard size C.P. brass flush pipe, spreaders and clamps all in C.P. brass complete in all respect Cat No. S4020112 Make M-cera size 375x390x590mm

Prov.& fixing of looking Glass with PVC Beeding with Plastic hard board or with Stods complete all respect of approved make

Please Enable Macros to View BoQ information