REPAIR TO SENTRY POST, BOUNDARY WALL INCLUDING PERIODICAL, PILLAR, CHAIN LINK FENCING, IRON POST AND OTHER MISC BR PORTION WORK IN ZONE - II AT MIL STN JAISALMER

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer-in-charge.

M&L for Plastering 15mm thick in CM (1:4) on stone wall surface(external wall surface) finishing the surface even & smooth with mixing of water proofing compund as per manufacture instructions. Note :- Water proofing compund shall be measured and paid sepeartely as supply only rate.

M&L for 15 mm thick, plaster in cement mortar (1:6) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for rendering 5 mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of cement primer all as specified & directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of distempering oil emulsion over a coat of primer surfaces all as specified & directed by Engineer-in-charge.

M & L for Preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified & directed by Engineer-in-charge.

M&L for Prepration of old plastered surface of ceiling and applying one coat of white wash complete all as specified & directed by Engineer-in-charge.

M&L for Prepration of old plastered surface of wall and applying one coat of white wash complete all as specified & directed by Engineer-in-charge.

Demolition floor hearth or wall tiling including cement mortar bedding and removing unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L Machine cut kota stone slab flooring 20- 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed by Engineer-in-charge.

Taking down shutter of any description exc 1 Sqm but n exc 2 sqm each complete all as specified & directed by Engineer-in-charge.

Taking down unserviceable chowkhat or frame with shutter (without taking off shutter from the frames) exc 1.5 sq.m but n. exc 4 Sqm each complete all as specified & directed by Engineer-in-charge.

Refixing in shutters in same opening of any description exc 1.00 sqm but n. exc 2.00sqm each complete all as specified & directed by Engineer-in-charge.

S & F Pressed steel frames of size 165X 60mm and 1.25 mm thick for doors with double or single rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified & directed by Engineer-in-charge.

S&F 2nd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panels of timber flate on both sides, with lock rail and panel of 9mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces the size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressed treated complete all as specified & directed by Engineer-in-charge.

S&F factory made 35mm thick 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part I section 8 clause 8.24 (a) supplied and fixed to chowkats complete all as specified & directed by Engineer-in-charge.

S&F stainless steel wire cloth 8 percent nickle 0.20mm nominal dia of wire and average width of aperature 1.40mm complete all as specified & directed by Engineer-in-charge.

S & F in repair of 300 mm long mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed by Engineer-in-charge.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth & priming coat with pink primer and applying two coat of sythentic enamel paint complete all as specified & directed by Engineer-in-charge.

M&L for preparation of old wooden surfaces of any description over 10cm width and applying one coat of sythentic enamel paint all specified.

S&F barrel tower bolt 150mm long aluminium anodised extruded section

S&F aluminium anodised handle 150mm long cast type

S&F butt hinge size 100mm extruded aluminium alloy with galvanised mild steel hinges pin, anodised and fixed type

S & F 250mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Taking down unserviceable glazed steel windows, fly proofing steel windows and ventilators etc

S&F MS square bar for window guard bars fixed indenpendently welded to ventilators and windows etc and similar article.

S&F steel ventlators with top hung shutters including box type hinges, steel peg stay complete

S & F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded (Glazed steel window)

M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

Demolition of cement concrete reinforced of any description and in any position not other wise specifically provided and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of 150mm bore set in cement mortar including demolition of packing under and hauching against sides of pipes complete all as directed by Engineer-in-charge. (Note :- Excavation and earth work shall be measured and paid separately.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of 200mm bore set in cement mortar including demolition of packing under and hauching against sides of pipes complete all as directed by Engineer-in-charge. (Note :- Excavation and earth work shall be measured and paid separately.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 150mm bore pipe all as specified & directed by Engineer-in-charge.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 200mm bore pipe all as specified & directed by Engineer-in-charge.

M&L for 150mm bore salt glazed stoneware drain pipes (ISI marked) laid in trenches and jointed in CM (1:1) and tested complete all as specified & directed by Engineer-in-charge.

M&L for 200mm bore salt glazed stoneware drain pipes (ISI marked) laid in trenches and jointed in CM (1:1) and tested complete all as specified & directed by Engineer-in-charge.

Dismantling of cast iron or reinforced concrete drain pipes 100 mm dia jointed in cement mortar

Dismantling of cast iron or reinforced concrete drain pipes 75 mm dia jointed in cement mortar

S&F, 100mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with cement & fixed to walls complelte all as specified & directed by Engineer-in-charge.

S&F, 75mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with cement & fixed to walls complelte all as specified & directed by Engineer-in-charge.

S&F in repair 100mm bore cast iron cowl (sand cast) all as specified & directed by Engineer-in-charge.

S&F in repair, 110mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and directed by Engineer-in-charge.

S&F in repair, 75mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls all as specified and directed by Engineer-in-charge.

S&F in repair, 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F in repair, 125mm/110mm dia PVC (SWR) gully trap, setting & jointing with solvent cement complete all as specified & directed by Engineer-in-charge.

S&F 100mm cast iron sanitary connection socket to fit WC outlet complete all as specified & directed by Engineer-in-charge.

Dismantling of posts or struts (wood, steel or RCC ) any section including taking out embeded portion and making good distrubed ground on concrete, brick work, masonry etc and removing of demolished materials out side MD land complete all as specified & directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description specifically provided for gates, staircase railings, framed truss etc complete all as specified & directed by Engineer-in-charge.

M&L Mild framed works such as angles, tees, channels, etc as in fenching posts large and small gates and grills, gratings and chainlink fenching etc, including hanging gates in pillar with proper pintle hinges, stops, hand made sliding bolts etc complete all as specified & directed by Engineer-in-charge.

Dismantling fencing wire mesh, any type complete all as specified & directed by Engineer-in-charge.

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified & directed by Engineer-in-charge. Note :- (i) Fixing only chain link fencing shall be measured and paid seperately. (ii) A BOO will comprised for assembling actual weight of chain link fencing.

Fixing only chain link MS galvanisd fencing, any size or type complete all as specified & directed by Engineer-in-charge. Note :- Supply only chain link fencing shall be measured and paid seperately.

S&F mild steel round Bar 10 mm dia cut to length bent to shape as required, for fixing chain link fencing fixed with nut & bolt as in tie bar complete all as specified & directed by Engineer-in-charge.

S&F Mild steel flat iron for securing of chain link fencing conforming to Fe 290 Gde E-165 in post and strut in fencing including fabrication i.e. cutting tops drilling holes notching for wire welding etc. complete all as specified & directed by Engineer-in-charge.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 15cm but not.exc 22.5 cm long,diameter of neck n exc12 mm complete all as specified & directed by Engineer-in-charge.

Dismantling of old barbed wire from fencing posts complete all as specified & directed by Engineer-in-charge.

S & F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and training and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Demolition of brickwork or stone/ boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework complete all as specified and as directed by Engr-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone all as specified & directed.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed.

Material and labour for flush pointing to squared rubble masonry, uncoursed or brought upto courses in CM 1:3 complete all as specified and as directed by Engr-in-charge.

M&L for Providing, precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts,boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match complete all as specified and as directed by Engr-in-charge.

M & L for Preparation of surfacces plastered or unplastered incl complete removal of existing treatment on old surface of wall and applying two coats of cement base paint

MARUDHARA CONSTRUCTION COMPANY

Habib Traders

GEMRARAMCONTRACTOR

S AND S Constructions