Refurnishing of lab for Equipment relocated in Thin Film at CSIO, Chandigarh

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within CSIO.Fly Ash & All kinds of soil.

Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses,Shelves, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Brick work with F.P.S. bricks of class designation 12.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 12.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4(1 cement : 4 coarse sand

Half brick masonry with F.P.S. brick of class designation 12.5 in foundations and plinth/ superstructure in. Cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm Make :- Godrej or Equivalent

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.Make :- Dorma/Dorset/Indobrass

Providing and fixing aluminium sliding door bolts, ISI marked poweder coated to required colour or shade, with nuts and screws(also powder coated) etc. complete : 250x16 mm Make:- Classic or Equivalent

Providing and fixing aluminium tower bolts, ISI marked, powder coated to required colour or shade, with necessary screws(powder coated) etc. complete : 250x10 mm Make:- Classic or Equivalent

Providing and fixing aluminium tower bolts, ISI marked, powder coated to required colour or shade, with necessary screws etc. complete : 150x10 mm Make:- Classic or Equivalent

Providing and fixing aluminium handles, ISI marked, powder coated to required colour or shade, with necessary screws etc. complete : 125 mm Make:- Classic or Equivalent

Providing and fixing aluminium hanging floor door stopper,powder coated to required colour and shade, with necessary screws etc. complete. Twin rubber stopper Make:- Classic or Equivalent

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing and laying Double Charge vitrified floor tiles in different sizes (thickness to bebspecified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm.Make :- Kajaria. (Tile to be Cleaned after fixing of any stains, patches etc before payment)

Providing and laying Double Charge Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm.Make :- Kajaria (Tile to be Cleaned after fixing of any stains, patches etc)

Providing and fixing Ist quality ceramic digital/printed glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete as approved by the Engineer in charge before fixing in size of tile 300X450 mm or above. Make :- Royal, Digital Series Kajaria

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter Make :- Prince/Diplast

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- harge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Make :- TATA / JSW

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Gutter (600 mm over all girth)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.Two or more coats on new work . Make :- Asian/Narolac/Dulux.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture Make :- Asian/Narolac/Dulux.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1-2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Make :- JK wall putty/Birla white/Asian

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer. Make :- Asian/Narolac/Dulux.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 fine sand)

Taking out existing wooden and aluminium door/Cupborad/Window shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Finishing walls with Acrylic Smooth exterior paint of required shade : New/Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface Make :- Asian Ultima or Equivalent

Demolishing cement concrete manually/ by mechanical means including disposal of material within CSIO as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within CSIO as per direction of Engineer-in-charge.In cement mortar.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within CSIO as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in- charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO : Of area beyond 3 sq. metres

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm

Dismantling aluminium/ Gypsum/steel/wooden partitions, doors, windows, fixed glazing and false ceiling, plaster ,kota stone,sun film ,wall paper, pvc flooring,G.I sheets roofing including,M.S. structure, ceramic tiles,chips/ mossaic/brick/stone flooring etc including disposal of unserviceable surplus material and stacking of serviceable material with CSIO as directed by Engineer-in-charge

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond CSIO for all leads including all lifts involved

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/Including filling of sapce between frame and wall with sealent appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / matching colour powder coated stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion . Powder coated aluminium (minimum thickness of powder coating 50 micron) ( The aluminium to be cleared properly of paint etc before payment ) (Clean of aluminium to be done)

Providing and fixing aluminium work for doors, windows, ventilatorsand partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS : 1285, fixed with rawl plugs and screwsor with fixing clips, or with expansion hold fasteners ncludingnecessary filling up of gaps at junctions, at top, bottom and sides withrequired PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling,C.P. brass / matching colour powder coated stainless steel screws, all complete as per architecturaldrawings and fiklling the gap between aluminium and wall with PU sealent the directions of Engineer-in-charge. (Glazing andpaneling to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision forfixing of fittings wherever required including the cost ofPVC / neoprene gasket required (Fittings shall be paid forseparately).Powder coated aluminium (minimum thickness of powder coating 50 micron). ( The aluminium to be cleared properly of paint etc before payment ) (Clean of aluminium to be done)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides Make :- GVK/Novapan/Merico

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) Make :- Saint Gobind/Modi Guard/Atul

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. Make :- Godrej or Equivalent

Providing and fixing aluminium Double bend handle round with SS screws etc. complete as per direction of Engineer-incharge Powder coated minimum thickness 50 micron aluminium as per direction of Engineer-in-charge

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and as per direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size 24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge. With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6 Make :- Armstrong DUNE RH 99 or Equivalent

Providing & fixing vertical blinds of louvers fabric woven of approved shades.The head rail should be powder coated aluminium alloy section with tilt gear hub delrinacetal louer carriers including any other fixtures to make the blind oprational and fixing in position all complete of Make - Vista or equivalent as approved by Engineer in charge before fixing.

Carry out petty Job for welding works with neccesry Tools, welding set & rod etc. For petty works which otherwise can not be measured all complete as direction by Engineer in Charge

Dismantling of existing recessed MCCB-TPN with enclosure and disconnection of 4 core cable of size 25 sq.mm etc. including shifting of dimantled material from site to store and making the surface furnished with cement plaster as required.

Fixing of MCB DP with enclosure/MCB TPN with enclosure/MCB-DB TPN/MCB-DB SPN/TPN Bus Bar chamber/MCCB TPN with enclosure/ on surface/ recess, complete with connections, testing and commissioning etc. as required and directed by Engineer-in-Charge.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel/ PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (i) Group-C

Wiring for circuit/ submain wiring alongwith earth wire with the 2X2.5 sq mm + 1X2.5 sq mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supplying and drawing of 3 x 4 sq. mm FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing of 3 x 2.5 sq. mm FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Wiring for circuit/ submain wiring alongwith earth wire with the 2X4 sq mm + 1X4 sq mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (Note:- this item includes PVC conduite pipe + PVC wire)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 5/6 A modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (Note: Suitable for fixing on PVC modular box for PVC trunking)

Supplying and fixing 15/16 A modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (Note: Suitable for fixing on PVC modular box for PVC trunking)

Supplying and fixing modular 3 pin 5/6 A socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (Note: Suitable for fixing on PVC modular box for PVC trunking)

Supplying and fixing modular 6 pin 15/16 A socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required. (Note: Suitable for fixing on PVC modular box for PVC trunking)

Supplying and fixing of U-PVC adaptable trunking system of size 100mm X 50mm complete with trunking cover etc. for housing the electrical modular box for fixing modular switch sockets, telephone socket etc, on the wall/tables/pillars etc. as required.

Supply and fixing of PVC 6 module conversation frame for CMS trunking with cover plate and blanking plate suitable for fixing in 100mmx50mm DLP U-PVC trunking for fixing the modular switch and socket 5amp./15amp. Complete as required at site.

Supply and fixing of RJ45 CAT6 Computer Jack with PVC modular box , base and cover plate suitable for fixing in 100mm x 50mm U-PVC trunking complete as required at site.

Supply of full glow G5 recessed type 30W LED Light Fitting of size 2' x 2', lumens - 3600 or more, operating voltage 230/250 Volts, 50Hz, suitable for office and complete in all respect with driver etc. Model/Make: RC370B LED36S of Philips OR equivalent model of Havells, CG or Wipro.

Supply of LED Batten of rating 20W, minimum lengh 1150mm, lumens effieciency not less than 100lm/watt, suitable for 230V, 50 Hz, single phase AC Supply, complete as required. Make Havells/CG/Wipro.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supply of 200 mm sweep , 32 watts, plastic Body Exhaust Fan, Air delivery minimum 520 m3/h 1350 RPM, including all accessories , suitable for 230V, 50 Hz, single phase AC Supply, complete as required. Make & Model: Havells' VENTILAIR DX Model Or equivalent model of USHA/CG.

Installation of exhaust fan of size upto 450 mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Supplying and fixing of 6 way (4 + 18), Double door, Double door, Double door, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Double pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 63 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Triple pole and neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63 A, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 6A-32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required. (Model should be got approved before installation)

Supplying and fixing TPN sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TPN MCB complete with connections, testing and commissioning etc. as required. (Model should be got approved before installation)

Supplying and fixing of 25mm size of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of 32mm size of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and fixing 20mm to 25mm PVC flexible pipe alongwith accessories on surface as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 4 X 25 sq. mm (28mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 4 X 16 sq. mm (28mm) size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Upto 35 sq. mm (clamped with 1mm thick saddle)

Supply of 4 core 16 sq.mm 1.1KV grade, one number XLPE insulated, aluminium conductor, armoured power cable confirming to latest IS standards.

Installation of wall mounted split Air Conditioner

Supply and fixing of MS powder coated floor /wall mounted stand for out door unit of split AC

Supply and fixing PVC hard drain pipe dia 25 mm with necessary joints for condense drain water from indoor unit to drain point/out side as per the site requirement

Shifting of Split Airconditioners outdoor units from wall to roof. Work includes pump down gas, leak testing and top up/charging of gas etc

Supply and fixing of AC copper pipes( suction and discharge line)with proper insulaton wrapig of tape & fixing of nail clamp etc as per site requirment

Supply and fixing of 4 core 2.5 Sq mm electrical cables in PVC conduct pipe .

Work of brick wall & surface cutting / chiesling up to bidth of 75 mm for the purpose of recessed PVC drain pipe /copper pipe and making the wall in good condition by cement plaster etc as per site requirment

J P Constructions