SPECIAL REPAIR TO TOILET BLOCK AND SPL REPAIR TO SEWAGE LINE AND OTHER SANCTIONED WORKS UNDER AGE B/R I AT ITARANA ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) complete all as specified.

Taking down chowkat or frame with shutters area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

BLANK

BLANK

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

Material and labour brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:4 complete all as specified & as directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.d.

Supply and fixing galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

S&F 4mm thick frosted glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

M&L preparation of new untreated wooden surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of pink primer.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked) complete all as specified.

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specifie

S&F steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

S&F mild steel framed work as in doors / gates / steel frames etc. of angle or other section with gusset plates, rails, braces, etc., complete of Gde E-165(Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. and fixed in position.

Supply & fixing steel windows with side hung shutters including box type / projecting type hinges with steel handles and peg stay with glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

Supply & fixing steel windows with side hung shutters including box type / projecting type hinges with steel handles and peg stay without glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

S&F for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M&L for PCC 1:2:4 type B-1 using 12.5mm graded crushed stone aggregate as in levelling course of floors and roofs 25mm thick finished fair & even complete all as specified & as directed.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L cement concrete (1:3:6) type C1 using 20 mm graded stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Material and labour glazed ceramic tiles (coloured) Ist quality 350mm x 450mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) (Ist quality) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for 20mm to 25 mm thick Granite slab of approved shade, as in platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including required cutting to suit the size of oval type wash hand basin over & including 20mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in kerb block with plain fair faces, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

M&L rendering 10mm thick in cement mortar 1:6 on surface other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work of walls, mixed with water proofing compound (ISI marked), finished even & smooth without using extra cement complete all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.

Supply only integral water proofing compound (ISI marked).

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L in repairs galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L in repairs galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F in repairs PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

Supply and fixing in repairs 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, including 15mm bore brass float valve hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

Supply and fixing in repairs 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, including 15mm bore brass float valve hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I

S&F in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repairs vitreous china wash hand basin, white, flat back of size 580mm x 450mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs vitreous china counter top basin size 450 x 525 x 195 mm shape ovel of PARRYWARE / JAQUAR / SOMANY / HINDWARE / PRAYAG as approved by GE including 32 mm CP waste coupling & PVC flexible waste pipe of 90 cm long complete all as specified & directed.

S&F as in repairs 15mm bore Stop valve/Angle valve fancy type of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

S&F in repair Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F in repairs pillar taps, (Swanneck type) cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia.

S&F in repairs 32/38/40 mm dia PVC flexible waste pipe 80cm long with socket for union, for WHB/urinal/sink complete all as specified.

S&F in repairs CP soap dish complete all as specified and directed.

Supply & fixing in repairs vitreous china squatting pan (Orissa pattern) water closet (white) size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:7:12) type F2 in filling complete all as specified.

Supply and fixing as in repairs PVC valveless syphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

Supply & fixing vitreous china bowl type urinal flat back, size of 465 x 355 x 265mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

S&F in repairs pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia.

S&F as in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

Supply and fixing 110mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including taking out old unserviceable pipe of any type with fittings and making good around complete all as specified and directed.

Supply and fixing 110 mm bore PVC (SWR) bends any radius complete all as specified.

S&F Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) all as directed.

Supply and fixing 110 mm bore UPVC (SWR) ISI marked vent cowl complete all as specified.

S&F PVC (SWR) floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement including taking out old unserviceable trap.

S&F PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement complete all as specified.

S&F 110 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal provided with oval access door complete all as specified.

S&F in repairs swivel shower rose (fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union all as specified and directed

Supply and fixing 75mm bore UPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including taking out old unserviceable pipe of any type with fittings and making good around complete all as specified and directed.

Demolition of existing lime concrete/PCC padding, roof treatment of any thickness laid over RCC roof/chajja etc., removing complete layer of bitumen under concrete/PCC padding, cleaning and washing of roof with water to remove dust etc as preparation to receive treatment all as directed by Engineer-in-charge.

M&L PCC padding (1:2:4) type B0 using 12.5mm graded stone aggregate over roof slab laid to slope in average consolidated thickness of 25mm and surfaces finished even and smooth without using extra cement complete all as specified.

M&L 15mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on top of chajjas and roof surfaces, finished even & smooth without using extra cement all as directed. (WPC shall be measured & paid separately)

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.5 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd or Hydrostop water proofing memdrane manufactured by M/S TIKIDAN as approved by GE, black finish reinforced with non-woven polyester matt (weighing not less than 150 gm/Sqm), with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed.

Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing.(iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen. (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate. (vii) The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

M&L for cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3, not exc. half brick thick (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)

M&L for PCC (1:3:6) type C2 using 40mm graded crushed stone aggregate as in foundation of stay assembly & poles and similar works complete all as specified.

S&F rolled mild steel work as in Stairs (framed) including stringers, treads, landing, balusters, hand rails etc. including cleats, brackets, etc. complete conforming to Grade E-165 (Fe 290) including necessary cutting, welding etc and fixing in position complete all as specified & directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying or cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas depth exc 1.5m and not exc 3m and getting out in soft/loose soil all as specified and as directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level n. exc 1.50 metre above the starting point complete all as specified.

M&L for PCC (1:2:4) type B2 using 40mm graded crushed stone aggregate as in foundation of stay assembly & poles and similar works complete all as specified.

M&L for 75mm thick PCC 1:2:4 type B2 using 40mm graded crushed stone aggregate as in floor, top surface finished even and smooth with using extra cement complete all as specified & as directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately.

Cutting into existing manholes/Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.

Cutting into existing manholes/Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 200mm bore pipe.

Dismantling and taking out existing old CI pipe including CI fittings/specials complete all as specified & as directed.

S&F 110mm bore PVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including demolition & breaking up 110mm bore PVC pipe with fittings.

Supply and fixing 110 mm bore PVC (SWR) bends any radius complete all as specified.

S&F 75mm bore PVC (SWR) ISI marked pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including demolition & breaking up 75mm bore PVC pipe with fittings.

Supply and fixing 75 mm bore PVC (SWR) bends any radius complete all as specified.

S&F cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified & as directed.

Demolition and breaking up 150mm bore drain pipes, salt glazed stone ware or reinforced concrete, set in cement mortar including PCC haunching and bedding, complete.

Material and labour PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

M&L for 200mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

Material and labour PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

Cleaning/Desludging of 150 mm sewage line by roding or other mean form adjecent man hole without breaking of existing pipe including washing the pipe with water after roding to make main line to smooth functioning complete. All as specified by Engineer in charge.

Cleaning/Dsludging of 200 mm sewage line by roding or other mean form adjecent man hole without breaking of existing pipe including washing the pipe with water after roding to make main line to smooth functioning complete. All as specified by Engineer in charge.

Cleaning/ desludging of manhole by excavating sludge depth 1.5 to 3 mtr depth and size not exceeding 4 cum each manual labour/ mechanical scrappers etc and disposel of the sludge including dumping of waste matrila outside the MOD land complete. All as specified by Engineer in charge.

Cleaning/ desludging of manhole by excavating sludge depth 1.5 and size not exceeding 2 cum each manual labour/ mechanical scrappers etc and disposel of the sludge including dumping of waste material outside the MOD land complete. All as specified by Engineer in charge.

Cleaning of septic tank of any capacity or description including cleaning and pumping out fluid, cleaning of sludge from compartment of septic tank including intercepting chamber & washing down with water complete and removing the sludge in covered van/trolley out side the MD land, complete, all as directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified.

M&L for 100 mm thick PCC 1:3:6 type C2 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified.

Supply only glass dividing strips 3mm thick and 38mm wide.

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc., flat iron fillets (for securing wire mesh etc) including necessary welding where required as per site requirement and other similar works complete, conforming to Gde E-165 (Fe 290).

Supply and fixing mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 22.5cm and n exc 30cm long and dia of neck 16 to 20 mm complete all as specified.

Fixing only mild steel galvanized chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire. Note :- Supply only chain link fencing shall be measured and paid for separately.

Supply only mild steel galvanized chain link fencing any size or type as directed complete all as specified. Note:- Flat iron, round bars, nut bolts and washer shall be measured and paid for separately.

S&F mild steel round bars as in tie bars fixed to fencing posts including cut to length, bent to shape, welding of bar at spots as directed and other similar works, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

M&L for hardcore of broken stone or boulders, gauge exc. 63mm but not exc 100mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

Taking down carefully, copper/aluminium unserviceable /perished point wiring any type for light/ fan/ socket or power complete including fittings such as switches, ceiling roses, pendant holders, lamp holders, bracket holders, regulators sockets, light fittings, lamps etc, and making good to disturbed surfaces of wall/floor/ceiling etc, complete, all as specified and directed.

Material and labour for point wiring for one light point controlled by one, one way switch with multistrand 1.50 Sqmm unsheathed copper conductor PVC insulated FRLS cable including continuous earth wire 1.5 Sqmm in green colour unsheathed copper conductor PVC insulated FRLS cable connected to common earth dolly in PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS in on New wooden boards fixed on wall for mounting switch, socket, regulators etc with and including 3mm thick phenolic laminated sheet top cover, complete, all as specified.

All as per description of serial item No. 124.00 above but for one fan point controlled by one switch and regulator complete all as specified and directed.

All as per description of serial item No. 124.00 here-in-before but for one 3 pin socket outlet 5 Amps controlled by one switch, 5 Amp on same board.

All as per description of serial item No. 124.00 here-in-before but for one 3 pin socket outlet 5 Amps controlled by one switch, 5 Amp independent board.

All as per serial item No. 124.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.5 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts.

Supply and fixing switch piano flush type, single pole, one way, 15/16 Amp, 230 Volts.

Supply and fixing socket outlet for 2 & 3 pin, 5 Amp, flush type 240 Volt.

Supply and fixing socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt.

Supply and fixing ceiling rose surface Bakelite 65x50mm two or three terminals.

Supply and fixing decorative ultra slim liner LED lighting fixture with extended polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride and connecting up with and including white coloured flat/round twin core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete, all as specified & directed. Make :- Havells Cat Part No LHEXBLP7PN1W018 or equivalent Make given in PS as approved by GE

Supply and fixing lamp holder, angular PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing in holder Adore LED lamp 9/10 watt complete all as specified and directed. Make :- Havells Cat Part No LHLDERHEML8X010 or equivalent Make given in PS as approved by GE

Supply and fixing new fan regulators electronic step up type socket size and connecting up, ISI marked flush type, 240 Volts complete all as specified and directed.

Supply and fixing ceiling fan 1200 mm sweep suitable for 230 Volts, 50 Hz, AC supply with down rod & canopy including provision of fan hook in ceiling for fixing of ceiling fan including necessary electric connection with 1 Sqmm, three core, flexible copper multistranded conductor cable all as directed.

Supply and fixing in repairs sheet metal enclosures, double door type, suitable for fixing MCB,s, SPN with 200 Amps rated bus bar, 8 way, 240 volts.

Supply and fixing sheet metal enclosure, double door type, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 4 way, 240 volts.

Supply and fixing MCB 32 Amps, single pole & neutral, 240 Volts.

Supply and fixing MCB 6 to 32 Amps, single pole, 240 Volts.

Supply and fixing in repairs MCB 63 Amps, single pole & neutral, 240 Volts.

Supply and fixing sub main wiring on and including PVC casing caping, 1100 Volts grade cable, PVC insulated copper conductor and over all PVC unsheathed for sub main wiring multistranded conductor of 6 Sqmm single core cable and earth wire of 6 Sqmm unsheathed copper conductor complete. (Two run of cable with one run of earth wire should measured as one length) including taking down existing unserviceable sub main wiring.

Supply and fixing 2nd class hard wood rectangular block open recessed of size 45x30x5 cm depth with 3mm thick hylum/Bakelite sheet on top grouted with 4 Nos bolts.

Supply and fixing LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete, all as specified & directed. Make :- C&S Cat Part No LTESS20WLED or equivalent Make given in PS as approved by GE

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified. Note :- Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

BLANK

M&L galvanised steel water tubing light grade of 40mm bore with & including all fittings complete laid in trenches. Note :- Excavation & earthwork shall be measured & paid for separately.

Material and labour earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part I and connection to main switch board or panel and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, 75 mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified & as directed. Note : PCC chamber shall be constructed at least 1.5 m away from the earth electrode. The pipe for watering shall be provided in slanting manner

M & L for dry sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover complete all as specified and directed. Note :- Thickness after punning shall be considered for payment.

M & L for brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection including taking down old unserviceable bricks complete all as specified & directed.

ARUN ENTERPRISES

Radha Enterprises

M/s S Amarjit Singh

DHARMA CONSTRUCTION

L P Singh and Co.

KARTIK ENTERPRISES

M/S GAURI CONSTRUCTION

M/s ASK Enterprises