GE/863/EWS-T-88 OF 2025-26 PROVISION OF TOILET BLOCK NEAR BDE HQ OFFICE POOH AND SPL REPAIR TO BLD

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil.

M & L for Cement concrete type D2 1:4:8 using 40mm graded stone aggregate in foundations, filling and mass concrete.

M & L for Pre-cast cement concrete type B1 1 : 3 : 6 block masonry with solid blocks, exc. 10 cm in width and setting in mortar (CM 1:6) complete all as specified and directed.

M & L for 40 mm thick Cement Concrete M-15 Nominal Mix (using 12.5 mm graded stone aggregate) as in damp proof course (DPC) to horizontal or vertical surfaces including necessary form work and mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. NOTE: - water proofing compound will be measured and paid separately.

M&L for Hard core of gauge n exc 63mm thick of broken boulder spread leveling watering ramming to true surface complete all as specified and directed by Engr-in-Charge..

M&L for 75mm thick P.C.C 1:4:8 type D-2 in sub base of floor complete all as specified and directed by Engr-in-Charge.

M & L for 25 mm thick PCC 1:2:4 type B1, 20 mm graded stone aggregate as in flooring including finishing cement concrete rough surface with out using extra cement.

M & L for non skid coloured ceramic tiles 7 to 8mm thick square / rectangular area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floor laid over 15 mm thick screed bed in CM 1:6 as in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surface of tile complete all as specified and directed by Engr-in-charge.

M & L for Glazed ceramic coloured tiles of size 300 mm X 200 mm X 7 mm thick as on vertical surfaces such as skirting, dados and rises to steps etc. over 10mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing the surface even and smoth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface and finishing the surface even and smooth without using extra cement secified and directed by Engr-in-charge.

Supply only Integral water proofing compound (WPC)

M & L for preparation of newly plastered or un-plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

Returning filling in including speading,leveling ,watering and well ramming in layers not exc 25 cm in soils complete all as specified and directed by Engr-in-Charge.

Removing of excavated Soil n exc 50m and depositing where directed at a level n.exc 1.50m above the starting point.

M&L for 75 mm thick PCC 1:3:6 type C2 in plinth protection finishing even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge..

M & L for precast cement concrete M-15 Nominal Mix (1:2:4) (using 20 mm graded stone aggregate), as in lintels upto 1.5 m clear span, cills, steps,seismic and other similar bands, plinth course, string courses, lacinng courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L for providing pre-cast cement concrete landing, cover slabs (for man holes etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:6 complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

S & F II class hard wood Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamferred, put together with glue pinned at joints. complete all as specified and directed by Engr In Charge.

S & F II class hard wood Plain, framed, pannelled shutters 35 mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers etc complete as specified.

S&F butt hinges, medium weight, cold rolled mild steel, size 100mm.

S&F MS sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, 250mm length.complete all as specified and directed by Engr In Charge.

S&F 150mm barrel tower bolts, stove enamelled black, with bright bolt.complete all as specified and directed by Engr In Charge.

S&F MS pressed handles, oval type, stove enamelled black size of 125mm.

Material & labour for two coats of synthetic enamelled paint over a coat of pink primer on new wooden surfaces exc 10cm width or girth including preparation of surfaces.complete all as specified and directed by Engr In Charge.

S&F Pre-painting galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strenght of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing of Fe 410W (Gde-E-250) etc (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

Rotational moulded polythylene water storage tanks of capacity 500ltr (Cylindrical vertical with closed top) hoisted and fixed in position all as specified.

S&F 20mm bore ball valve high pressure of PTMT with epoxy coated alluminium rod and high density plastic ball secrewed for iron pipe and fixed . ( Minimum wt 15 mm - 142 gms/20 mm - 210 gms)

S&F 15 mm dia of pipe Gun-metal, globe or gate valvees with iron wheel head, screwed both ends for iron pipe and fixed.complete all as specified and directed by Engr In Charge.

S&F 20 mm dia of pipe Gun-metal, globe or gate valvees with iron wheel head, screwed both ends for iron pipe and fixed.complete all as specified and directed by Engr In Charge.

S&F 15mm bore Galvanised steel tubes, 'medium grade' with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr In Charge..

S&F 20mm bore Galvanised steel tubes, 'medium grade' with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr In Charge..

S & F Vitreous China , Semi pedestal pattern (Anglo Indian Type), white and fixed in repairs (excluding fixing bolts, flushing cistern and flushing pipe)

S & F for plastic water closet seat cover, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging deviced complete all as specified and directed .

S & F for Wash Hand basins, Vitreous China, white, flat back, size 550x440mm, including cutting for and pinning in ends of brackets or erecting stand, angle bracket (but exclusive of fixing of supply, waste pipe, taps) complete all as specified and directed.

S & F PVC valveless, syphonic action type, 10 ltr flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, CP down pipe and connecting to the WC and making good to the floor with PCC all as specified and directed.

S & F Vitreous China Half stall type urinals, white, with geating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (excluding of fixing supply pipe, flushing cistern, flush pipe, trap and waste pipe) complete all as specified and directed.

S&F urinal spreader of PTMT 15mm size with PTMT nuts of length 300mm complete all as specified and directed by Engr-in-Charge

S&F bib taps 15mm dia fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed. complete all as specified and directed by Engr In Charge.

S&F Angle stop valve of PTMT any colour pressure screwed for iron pipe and fixed (15mm minimum weight 90 Gms) 15mm dia fixed to iron pipe.

Supply & fixing 15mm pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down , high pressure, with or without lettered 'Hot' or Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed. Bore of pipe in 15mm complete all as specified and directed by Engr In Charge..

S&F for waste coupling of PTMT for 32 mm bore dia of discharge pipe (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms)

S&F PVC connections 15mm size with PTMT nuts of length 600mm

S&F cast iron floor trap 75mm out let dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)..

M & L for Gully traps salt glazed stoneware (SGSW) square or round mouthed type 'P' of size 180x100mm for drain pipes complete all as specified and directed.

S & F 75 mm dia bore PVC (SWR) pipes single socketed , in any length with rubber ring joints , laid in tenches or in floors

S & F 110 mm dia bore PVC (SWR) pipes single socketed , in any length with rubber ring joints , laid in tenches or in floors

S & F 75 mm dia bore PVC (SWR) bends any radius

S & F 110 mm dia bore PVC (SWR) bends any radius

S & F 110 mm dia bore PVC (SWR) junction single 'T' equal or unequal

S & F PVC (SWR) 110 mm bore vent cowl

S&F soap dish vitreous china white, approximate size 160x160x90mm embedded in the wall.

S & F of 20 mm dia Aluminium anodised tubular towel including one pair of fixing brackets complete all as specified and directed.

S & F toilet paper holder , vitreous china box type fixed to wall with chromium plated brass screws in repairs.

S & F for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

M& L for 150mm bore SGSW Pipe including PCC 1:4:8 type D-2, (using 40mm graded stone aggregate) as in bed of drain for 150mm bore pipe incl packing under , and haunching against the sides of the pipes after they are laid in and tested all as directed.

Dismanling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Naintal or similar pattern roof coverings complete all as specified and directed

S&F Pre-painting galvatume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strenght of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed

S&F Fingre plates 200 to 300mm long and 80 to 100mm wide (transparent plastic shett of 1mm thick) fixed with brass chromium plated screw all as specified and directed

M & L for preparation of new steel surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness inclduding cover fillets.

Taking down chowkats or frames not exc 1.5 sq.m each but with shutters (without taking off shutters from the frames).

Taking down chowkats or frames exc 1.5 sq.m but n.exc 4 sq.m each but with shutters (without taking off shutters from the frames).

Dismantling timber all as per item above but in fillets, rails, posts, rafters, purlins, etc under 40 sq.cm in section.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 3 & n.exc 6 sq.cm complete all as specified and directed.

M & L for 6mm thick (No of ply 5) plywood, grade BWR, type BB, fixed with nails to timber frame work as in ceiling complete all as specified and directed.

S & F 300mm length aluminium alloy, anodised, sliding door bolt hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed.

S & F 150mm Aluminium handles, cast type, anodised

S & F 150mm aluminium, anodised, barrel tower bolts of extruded section and fixed.

M&L for RCC slab Type B1 1:2:4 (20mm graded) supported on wall, beams and coloum in floors, roofs, landing, blaconies, canopies, deck slab and in sheves and like that completed all as specified and directed.

M&L for se and waste form work to soffits of suspended slab, such as roof slab, floor salb, landing and simillar work not exec 200mm thick completed all as specified and directed.

S & F steel window/ventilator with side hung shutters incl projection type hinges with steel handles, tower bolt and steel peg stay completed with glazing bars dovetailed or welded all as specified.

S&F Framed work as in doors or gates of angle, grill, gratings or other section with gusset plates, rails, braces, etc. complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410 (grade E-250) all as specified and directed.

M&L 1.25mm mild steel, plain, black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws in steel framing with riveted or welded , and complete all as spd and directed.

M & L for preparation of old steel surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint completed all as specified and directed.

S & F clamps, hold fast,hook washer & similar small articles conforming to Fe-290 Gde-E-165.

M & L for providing cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in hold fast blocks.

M & L sheet glass, 4mm thick ordinary quality and glazing with oil putty or beadings in square not exc 0.5 sqm in each pane.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified and directed.

M &L 75mm thick cement concrete type D2 1:4:8 in sub base floor complete all as specified and directed.

M&L for Machimne cut kota stone slab flooring 20-25mm thiick over and incl 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete ass as specified.

M &L chequered cement concrete tile 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry over 20mm thick scrred bed in cement mortar 1 :4 as in floors with grey cement and pigment complete all as specified and directed.

M & L for non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Demolition of brick work or stone / boulder massonary, build in cement mortar incl all quoins , pillers etc.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc.

M & L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement).

M & L for preparation of new plastered surface or previously untreated walls surfaces and applying two coats of cement base paint over coat of primer on wall complete all as specified and directed.

Point wiring complete with 1.5 sqmm single core PVC insulated with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi standed copper conductor drawn through and including non metallic rigid PVC conduit with all conduit accessories (concealed)/ Casing and caping and including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuity conductor, fabricated steel terminal box made out of 1.6 mm thick MS sheet concealed in walls with 3 mm thick bakelite sheet ISI marked top cover with brass screws and cup washers for housing the switches, socket outlets, fan regulators etc for One light / Exhaust Fan point controlled by one switch, all as specified and as directed.

All as per Srl item No 98 here-in-before but controlled with one 3 pin socket outlet 5 Amp on same board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 98 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the independent board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 98 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with cable 2.5 sqmm including provision of 1.5 sqmm single core multistanded PCV insulated copper conductor as earth conducting conductor complete all as per specified and directed by Engineer-in-Charge.

Supply and fix Modular switch 1 way 6A, 1 module type, 230 volts, ISI marked complete.

Supply and fix Socket, 6A - 2/3 pin combined 2 module, multipurpose flush type, ISI marked complete all as specified and as directed.

Supply and fix Socket 6A/16A - 2/3 pin combined 2 module, multipurpose flush type, ISI marked complete all as specified and as directed.

Supply and fix Modular switch 1 way 16A, 1 module, multipurpose flush type, ISI marked complete all as specified and as directed.

M&L Ceiling rose, 3 terminal with ISI mark all as specified and directed by Engr-In-Charge.

Supply and fix NEO LED pannel warm round recessed mounted 15w, ultra slim profile with extruded polycabnate , enviromental friendly energy efficient, connected with 23/ .0076 twin core pvc flexible cable complete all as specified and directed.

Supply and fixing surface & wall mounted LED 20W (Warm white) tube light fitting batten 4 feet, mirrorlite slim type with extruded aluminium housing alongwith 20W LED lamp PC body with all accessories all as specified and directed by Engg-in-Charge. Make: Crompton Cat No. LDLL20-WW (Warm White) or Havells/Wipro/ Bajaj

Supply and fixing in replacment surface & wall mounted LED 5W tube light fitting batten mirrorlite slim type with extruded aluminium housing alongwith 10W LED lamp PC body with all accessories all as specified and directed by Engg-in-Charge. Make: Crompton Cat No.LDLL05-WW (Warm White) or equivalent

Supply and fixing of sheet metal enclosure double door for DBs single pole and neutral for 8 way 240 volt complete all as specified and directed by Engineer-in-Charge

Supply and fix MODULAR WHITE COVER PLATE WITH FRAME White cover plate with frame, 3 module ISI marked complete all as specified and as directed.

Supply and fix MODULAR WHITE COVER PLATE WITH FRAME White cover plate with frame, 6 module ISI marked complete all as specified and as directed.

Supply and fix MODULAR METAL FLUSH BOX Metal flush box 3 module ISI marked complete all as specified and as directed.

Supply and fix MODULAR METAL FLUSH BOX Metal flush box 6 module ISI marked complete all as specified and as directed.

Supply & Fixing LED light fitting 1 x 9 W/1 x 10 W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make havells/Bajaj

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. (i) SP 6 to 32 Amp

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.(ii) SPN 32 AMP

S&F exhaust Fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V,50 Hz, RPM 1200, Copper winding of sweep 250 mm complete all as per specified and directed by Engineer-in-Charge.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated 10 sqmm two core aluminium solid conductor , served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular, complete all as specified and directed by Engineer-in-Charge .

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below the ground level with top edge of the plate not less than 1.5 mtr below the normal ground level connected to the galvanised earth wire 4 mm dia by means of bolts, nuts hook nuts and washers of galvanization of steel all as shown in electrical plate no 3 connected to earthing testing point all as specified or indicated including testing on completions.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as specified and directed by Engr-in-Charge

Taking down unserviceable submain wiring and service cable alongwith batten /PVC conduits etc. and making good disturbed surfaces of walls/floors and match the existing surface all as directed at site.

Taking down unserviceable main switches, DBs with MCB SP/Isolators by unscrewing form board complete all as specified and directed by Engineer-in-Charge

Matrial & Labour for point wiring using approved colour coding as per IS with using approved coper coding as per IS 1.5 Sqmm multistranded , 1100 volt grade copper conductor FRLS cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continuous earthing in & incl PVC casing & caping /Conduit pipe with accessories having ISI mark fixed on wall surfaces / ceiling including provision PCV Box on top for fixing switches sockets etc. all as specified for one light point / fan / Bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 126 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the same board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 126 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the independent board with cable 1.5sqmm including provision of 1.5 sqmm single core multistanded PCV insulated copper conductor as earth conducting conductor complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 126 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with cable 2.5sqmm including provision of 2.5 sqmm single core multistanded PCV insulated copper conductor as earth conducting conductor complete all as per specified and directed by Engineer-in-Charge.

Supply and fixing of switch piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge,

Supply and fixing of socket outlet 3 pin 5 Amp 2-in-one 230 Volt flush type complete all as specified and directed by Engineer -in-Charge.

Supply and fixing of switch piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge,

Supply and fixing of Socket outlet 2 in 1, 3 pin, 5 and 15amp flush type single pole one way complete all as specified and directed by Engineer -in-Charge,

M&L Ceiling rose, 3 terminal with ISI mark all as specified and directed by Engr-In-Charge.

Material and labour for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings. Make : Anchor/leader/havells

Supply and fixing 9 watts LED backup lamp of 4 hours backup, with auto switch on mechanism in case of power failure, works as regular 9w lamp in normal mode and a 4w lamp in backup mode all as specified and directed by Engg-in-Charge. Make: Havells

Supply and fix in replacement LED Batten 20W , 4 ft (Approx) length ultra slim square profile with extruded polycabonate, enviromenental friendly, energy efficient , connected with 23/.0076 twin core PVC flexible cable complete all as specified and directed. Make- Havells / Philips / Crompton

Supply & Fixing LED Bldg security light fitting 30 Watt with best in class design & robust heat sink along with class leading IP 65,IK & surge protection for long lasting performance connected with copper conductor cable of suitable size. Make Havells/Bajaj/Crompton. Note:- Sutable size bore of Security light suitable for GI Bracket measured and paid seperately in respective item.

Material and Labour street light bracket made out from GI Pipe 32 / 40 mm bore light grade 1.20 meter long bent to required shape and fixing to poles etc including fixing of clamps, nuts, bolts etc as specified and directed by Engr-in-Charge.

Supply and fixing of sheet metal enclosure double door for DBs Triple pole and neutral for 4 way 415 volt complete all as specified and directed by Engineer-in-Charge

S&F TPN 63 Amp,10 KA complete all as specified and directed by Engineer-in-Charge

Supply and fixing of sheet metal enclosure double door for DBs single pole and neutral for 12 way 240 volt complete all as specified and directed by Engineer-in-Charge

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.(i) SP 6 to 32 Amp

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.(ii) SPN 40 To 63 AMP

S&F in replacement exhaust fan, Steel body AC Single Phase, 230V of size 450 mm sweep heavy duty, with blade and frame and louvres. complete all as per specified and directed by Engineer-in-Charge.

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded, single core 1100V grade 2x6.0 sqmm FRLS complete drawn in and includindg medium grade rigid non-metallic PVC conduit and its accessories along with 1x 6.0 sqmm PVC insulated unsheathed copper conductor multi sranded single core copper FRLS cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated 16 sqmm two core aluminium solid conductor , served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular

Supply and fixing House service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Med. Grade), with two nos of suitable size of clamp,nuts, bolts and wahers etc fixed to GI sheet roof complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below the ground level with top edge of the plate not less than 1.5 mtr below the normal ground level connected to the galvanised earth wire 4 mm dia by means of bolts, nuts hook nuts and washers of galvanization of steel all as shown in electrical plate no 3 connected to earthing testing point all as specified or indicated including testing on completions.

Schedule of Credit

Please Enable Macros to View BoQ information