Construction of Public Purpose Building in ongoing scheme of 776 Tenements at Stanley Hospital Seven Wells scheme at Old Jail road in Greater Chennai Corporation Division 55 Zone V

Amount

Installation Charges inclusive of Transportation to site and the Bored pile equipment employed for the works including setting up of pile driving equipment with all accessories and tools at each of the pile location based on the sequence of operation approved by the departmental Engineers irrespective of the location and distance involved in movement of pile driving equipment etc., complete.

Providing and constructing cast in situ hydraulic bored piles of 450mm diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc., Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Earth Work Excavation and deposting on banks with initial lead of 10m and initial lift of 2m in hard stiff clay stiff black cotton soil, hard red earth, shales, muram, gravel, stony earth and earth mixed with small boulders etc., as per SS 20B excluding hard rock requiring blasting inclusive of shoring shuttering, baling out water wherever necessary and including refilling consolidation etc., complete in all respects complying with relevent standard specifications and as directed by departmental officers. (With Narrow Cutting)

Upto 2m depth

Supplying and filling with Gravel or good earth well watered rammed, and consolidated complying with relevant standard specifications etc., complete and as directed by the departmental officers.

Supplying and Filling with M - sand in foundation and others sub structures for 100mm thick and well watered, rammed and consolidated by power compacter. The rate includes the cost of M sand, compacting with mechanical compactors, labour charges for leveling, loading & Unloading and Transportation charges etc., complete and as per the standard specification

Providing pre constructional Anti-termite treatment for the construction of building including cost of chemicals labour as per standard specification. Labour for preparing the area for treatment by spreading chemicals and other incidental charges complete. The rate shall be inclusive of giving anti termite treatment to the building for the following four stages including breaking the termite moulds making holes with crow bars at an interval of 12" to a depth of 8" in the periphery of the building including flooring area and pouring chemicals etc., complete as per ISI 6313/1981.

Providing and Laying PCC 1:4:8 (1 of Cement, 4 of M-Sand and 8 of graded metal) using 40mm metal including cost and conveyance of all materials mixing, laying, compacting, curing etc., complete and as directed by the dept. officers.

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge. b)For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

for plane surfaces such as rectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.

Providing and laying in position, RMC M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/mᶾ and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (4.51 cu.m.) 6972 kg. of 20mm machine crushed stone jelly and with about (3.01 cu.m.) 4687 kg. of 10-12mm machine crushed stone jelly and with about (4.22 cu.m.) 6757 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards.

For Foundation and Basement

For Stilt Floor

For First Floor

For Terrace floor:

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete / PVC cover blocks to maintain the cover as required.Rate to include all bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Brick work in following Cement Mortar using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS:12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

For foundation & basement

For Ground Floor

For First Floor

For Terrace Floor

Brick partition walls of 11.50cm thickness using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

For Ground Floor

For First Floor

Weathering course-using Concrete broken brick jelly 20 mm gauge in pure slacked lime (No sand to be used) over RCC roof slab. The proportion of broken brick jelly to slaked lime being 32:12½ cft well beaten by wooden beaters for giving required slope and thickness required etc complete complying with standard specifications and as directed by Departmental Officers.

In Terrace floor

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supply and applying water proofing treatment for Sunken portion and Water tank, Raft bottom and sides etc. using cement admixed with water proofing compound in the following order.

i) Making ' V ' grooves at the construction joints of size 20 x 20 mm and filling the "V" Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement

ii) Supply and Fixing of 50 long 18 mm dia GI nozzles in the hole of about half the depth of member size along construction joints, and honey comb areas at a spacing not more than 1m c/c.

iii) Supply and Applying injection grouting through the nozzles grouting pumps with a minimum pressure of 2 kg/sqcm with cement slurry admixed with CICO Non shrink Polymeric Water Proof Grouting Compound or approved equivalent at the rate of 2% by weight of cement.

iv) Sealing & cutting of nozzles and leveling the surface using integral Waterproofing compound CICO NO.3 or approved equivalent in the ratio 1:1by weight.

v)Supply and applying one coat of TAPECRETE Acrylic Polymer Modified Cementitious Slurry Coat over well prepared surface as a Primer and applying CICO CORCHEM 206 - I Polyurethane Based Elastomeric Coating to the thickness of 1.5 mm in 2 coats over TAPECRETE slurry coat applied surface.

vi) Lay protective plaster layer with 12mm thick Cement Mortar 1:4 (1 cement: 4 coarse sand) admixed with Normal setting integral Waterproofing compound CICO NO.1 or approved equivalent conforming to IS 2645 at the rate of 2% by weight of cement over the third coat of brush topping. Plaster shall be cured by spraying of water for the next 7days. The entire water proofing system shall be protected with a 25 mm thick extruded polystrene with necessary low VOC adhesieve

Paving the floor with best brandaed quality Vetrified Tiles of size 1200 x 600 x 10mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality lapato Granite Stone Slabs of size 1200 x 600 of 16 / 18mm thick laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with matching colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Polishing and Nosing the Granite Slab To Half Edge to round shape and finishing the surface neatly etc. complete complying with standard specification as directed by department officers

Paving the floor with kota stone laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing Ceramic Tile 300mm x 450mm x8mm best approved quality and colour in all shade of the glazed tiles in all floor over a base layer in Cement Mortar 1:2 (1 of Cement and 2 of M Sand)10mm thick and laid in situ true alignment and pointed neatly with colour cement suit the colour of the tiles fixed in position without any air gap in the tiles neatly etc., complete complying with standard specification and as directed by the the departmental officers. The Colour & quality of tiles should be got approved by the Executive Engineer before use in work.

Supplying and Laying the floor with antiskid ceramic tiles of approved quality and size of 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Plastering of 12 mm thick for Internal walls with cement mortar 1:5 (1 of cement : 5 of fine river sand) according to specifications. Rate shall include for providing GI chicken mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying in position with suitable clamps/screws. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportation charges, loading, unloading, preparation of surface, necessary hacking in RCC surface, scaffolding, stagging, tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering 15 mm thick for external surfaces with Cement Mortar 1:5 (1 of cement : 5 of P sand) with water proofing compound of “CICO No.1 or equivalent“ as per Manufacturer's Specification with sponge finish (washed sand finish) all complete as per specification and as directed. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering 10 mm thick for ceiling including slabs, beams and column drops and staircase waist slab, sunshade, drops, chajjas etc..with Cement Mortar 1:3 (1 of cement : 3 of P sand) according to the specification. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and painting of two coats of Acrylic emulsion paint of approved shade and colour over one coat of DCP Primer including one coat of Acrylic Wall Putty with DCP Primer. Rate including all brush, roller, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.(Ceiling & Internal surface)

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. The rate including cost of materials, brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

FALSE CEILING WITH GYPSUM BOARD Providing and fixing suspended false or Equivalent make which includes providing and fixing GI perimeter channel of size 0.50mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall / partition with the help of nylon sleeved and screws at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thick with two flange of 15mm each from the sofit at 1220mm centres with ceiling angle of width 25mm x 10mm X 0.55mm thick fixed to sofit with GI cleat and steel expansion fasteners. ceiling section 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lops of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel,etc,complete complying with standard specification and as directed by the departmental officers.

Providing, fabricating and fixing mirror panelling to walls using 6 mm thick copper-free silvered float glass mirror (clear) with 15 mm bevel on exposed edges, mounted over 12 mm BWR plywood fixed true to line and level, using mirror-safe neutral-cure silicone and double-sided PE foam tape, with 3–5 mm perimeter gap sealed with non-staining silicone, including necessary aluminium sections/ply framing where required, cut-outs, edge polishing, cleaning, protection and all labour, materials, tools and scaffolding, complete as per drawings and Engineer-in-Charge.

Glass Partition: Supply & Installation of Full Height Slimline Partitions systems of 45 x 25 mm thick section with black anodized finish on all four sides for the partitions using 004M as verticals at the solid partition junction & Horizontals at top & 004 & 005 at bottom with snap on option for installating glass & 'T' Section, corner Section & Vertical "I" Section between Glass to glass from FFL upto False ceimg/True Ceiling. Rate include supply & Installation of 10 mm thk toughened glass with double sided adhesive tapes for glass to glass butt joints

Supplying and Laying of Puzzle type Gym floor mat of 25mm thick etc., complete as directed by the Departmental O f ficers and as per standard specifications.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work (As per PWD S.R. 2024-2025, Pg.No.114, Unique Code-M0675)

Supplying & Installing CURTAIN BLINDS with Sunscreen perforated Roller blind optima series Basket 125 Tex with fabric specification of (Fabric compositition polyster 22% and PVC78%, Openenss Factor-5%, Thickness -0.68MM +/-5%, weight per m2 -480 GSM, yarns count in wrap/ weft/cm 19/18+/-5%, Fire Resistance-FR(USA) KFI(Korea), Tear Resistance-wrap11.9 daN+/- 5%,WEFT 150 daN+/-5%,colour fastness-6-7/8 (white colour base), artificial llight xenon lamp, UV resistance Min3 (White colour base), width 2.5M & 3 M. The Roller mechanism shall be a moulded unit made from engineering grade plastic polymer with PVC spring support. The Fabric shall be attached to the roller tube with high quality self adhesive tape with manual operation. The fabric shall be attached to the tube with adhesive strip. It should have minimum one ton fabric which must be placed on the roller before the working section of fabric start Operational action shall be smooth including necessary hardware for fixing at all places & as directed by Engineer-in-charge etc complete. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc. complete and as directed by the departmental officer (The materials quality, brand, colour, shade should Be approved by the Executive Engineer before use on works).

Solid PVC Door Shutters using 19 gauge 19mm MS square tubes for styles and outer frames.15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigitdly fixed in position including necessary furniture and fittings. The over all size of styiles shall be 50mm x 30mm. The over all size of top rail, Lock and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Best Indian Teak Wood Panelled door in double shutters with frames 100x75mm at side, verticals and top. The shutters shall beof 40mm thick with moulded fixed in c.c.1:2:4 6Nos.of butt hinges 125mm long including wind appliances, furniture, iron panels in 20mm thick planks, 6Nos.of iron hold fasts fittings, 1No.of iron padlock 15cm long for locking arrangements and fixing inposition, etc.,complete

For making and fixing M.S.Sheet Door of required size with two shutter using necessary M.S.Angles 50x50x6mm/40x40x6mm "L" Angles as diagonal Bracings 4Nos. for each shutter and centre Bracings for 1No.for each shutter. M.S.Flats 25x6mm/40 x6 mm and M.S.Sheet 1.25mm thick (18 gauge) and providing hinges welded with M.S.Angles 50x50x6mm bits at three places at equal intervals on both sides, Latches 25cm size length for locking arrangements providing 12mm dia. M.S.Rod running through the hinges on both vertical side for easy swining purpose of doors including one coat of primer, cutting iron members, welding fixing door in position, etc. complete

Supplying and fixing of M.S. Grill of approved design for doors, windows, open courtyard, Grill gate etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specifications.

Manufacturing, supplying and fixing of Stainless Steel Hand Rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm, thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 x 100 x 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges etc., complete complying with standard specification and as directed by the Executive Engineers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost fpriming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supply and Delivery and fixing of outside MS Ladder of 45cm clear wide made out of 50 mm x 50mm x 6mm MS angle for sides and steps in 16 mm MS plain rods fixed at 30cm C/C welded jointed etc ., providing with suitable side supports, clamps and locking arrangements provided with two coats of approved enamel paint over one coat of redoxide paint , for providing access to roof top of OHT of suitable inclined length , including bottom anchorage and transportation and as directed by TWAD Board officers. The rate includes concrete bed block in CC 1:2:4 using 20mm HBGS at top and bottom of suitable size with necessry anchor bolts.

Supplying and Erecting Pull and Push Type gear operated Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.Gear Operated Type (from 8 sqm. to 12 sqm. Area)

Plumbing Works

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, unioncoupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting.

Supply and fixing of Large Size White Glazed Earthenware Flat Back Urinals (approximately size 600 mm × 400 mm × 350 mm) of approved make and quality, including providing and fixing CP brass spreader with union, CP brass flush pipe with unions, suitable flush tank/valve connection, CP brass waste coupling, rubber gaskets, PVC/CI waste pipe connection to G.I. trap and floor drain, necessary brackets, screws and all other required specials, including cutting and making good of walls and floors wherever necessary, complete as directed by the Engineer-in-Charge.

Providing and fixing in position vertically marble partition in the urinals with Raj Nagar marble stone of white hard, dense hemogenious colour without cracks, and fissures of size (3.0+2.0)5'height thickness varies from 18 to 20mm including making grew in the wall and pointing and packing with cement mortar 1:3 polishing, finishing on both sides etc., as directed at site.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position best quality stainless steel sink of size 600mm x 450mm 200mm depth including the cost of 32mm dia PVC waste hose, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of sink at granite top in position white lead and giving necessary water supply connection etc., complete complying with standard specification and as directed by the departmental officers. (The Sink and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary block work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Supplying and fixing position PVC Nahani Trap / Floor Trap of the 100 x 75mm with stainless steel gratings sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the PVC pipes, etc., complete complying with standard specification.

Supplying and fixing position PVC Nahani Trap / Floor Trap of the 100 x 75mm with stainless steel gratings sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the PVC pipes, etc., complete complying with standard specification.

15mm dia Long body Tap

15mm dia Swan Neck Tap

Supplying and fixing in position best quality and approved variety of new Gun Metal Gate Valve / Wheel Valve heavy type excluding the fixing charges but including necessary cutting & threading of GI pipes for jointing the GI specials and providing two coats of painting with good quality and approved variety of anti-corrosive paint over a coat of red oxid primer coat in the case of pipe line above ground level and one coat of tarring in the case of pipe line below ground level etc., complete

25mm dia Gun metal gate valve

50mm dia Gun metal gate valve

Supplying, laying and jointing UPVC pipes of approved quality and best variety pipes of the following dia including labour for fixing UPVC Specials (excluding charges for cutting and threading and cost of such specials) with necessary shellac, thread ball, etc., and making holes on the wall / concrete and making good the dismantled portion to the original condition with necessary brick work / concrete. The pipes are to be painted with one coat of tar and tightly pastened with tar dipped gunny tape, etc., complete complying with standard specification. The UPVC pipes shall be got approved by the Executive EnUPVCneer before use on work. (The earth work excavation, re-filling the trench with excavated earth, sand filling, etc., shall be measured and paid separately under respective items). For External Water supply arrangements. (Below Ground Level)

50mm dia UPVC Pipe ( Below GL)

40mm dia UPVC Pipe

32mm dia UPVC Pipe

25mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying, laying and jointing PVC soil / waste pipes of approved and best variety conforming to IS. Specification with ISI. mark of the following sizes including, cutting and threading of PVC Pipes, fixing specials but excluding cost of such specials but including fixing to wall with necessary teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in roof and making good the dismantled portion to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges. The PVC Pipes should be got approved by the Departmental Officers before use on work. Above ground level.

75mm dia PVC Soil Pipe

110mm dia PVC Soil Pipe

160mm dia PVC Soil Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

P.V.C Cowl 110mm dia

P.V.C Cowl 75 mm dia

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110mm dia PVC Pipe

Construction of Inspection chamber or manhole of the following size including necessary earth work excavation in all soils to full depth as may be directed with sand filling at bottom of the chamber for 10cm thick, concreting CC 1:5:10 using 40 mm guage HBGs jelly 10 cm thick and sode walls 9" thick brick work in cement mortar 1:5 using Fly Ash Bricks of 230 x 110 x 75mm filling the size of foundation with excavated earth, plastering with cm 1:3 20m thick for inside and bottom and making necessary benching with brick jelly cement concrete to the required slope and finishing neatly etc., complete.

Inspection chamber of size 0.60X0.60x0.60M

Inspection chamber of size 0.60X0.60x0.90M

Inspection chamber of size 0.60X0.60x1.20M

Inspection chamber of size 0.60X0.60x1.50M

Inspection chamber of size 0.60X0.60x1.80M

Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with frame size 0.60x0.60m including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.

Providing rain water harvesting pit of 1.50m dia and 1.50m depth with necessary earth work excavation,erecting the five nos of Rcc collar of 1.50m dia,sand filling of 0.60m depth,filling of 40mm HBS Jelly of 0.60m depth and covering with Rcc cover slab of 50mm thick and also connecting 110mm dia PVC pipe of 10.00m legth including transporting charges,fixing,etc.complete.

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

ELECTRICAL WORKS

Metering Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS Channels, fasteners, etc., RYB indication lamps, internal wirings, Digital voltmeter and Ammeter and other required accessories for the complete operation as per the Tangedco requirements. Necessary approval to be obtained from Tangedco before procurement including all associated control wiring. 1set of 200/5A CT with TNEB metering provision and 1 nos of 200/5A CT for APFC.. For all items in this section, the rate includes necessary supports as required at site. No extra payment will be made for the same. Rate shall inclusive of factory witness test and all accessories, breakers , control wiring, models has to be followed as per in the technical specification. The panel should be erected on Anchor fastners, bolts and nuts for mounting the Indoor Panel as directed by engineer-in charge/department superior engineers.

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel made up of 2mm powder coated MCCB Indoor Type Three Phase Changer Over Main Panel with suitable to accommodate 250A 4 pole Three phase Change Over Switch-1No. as incomer for EB Source and as incomer for DG Source 2nos of 250A 4Pole MCCB, 3nos of 160A 4Pole MCCB, 2nos of 100A 4Pole MCCB and 1no of 63A 4Pole MCCB's, compartment for as O/G supply with the provisions to accommodate Busbar chamber and cable chamber with size of 33x6mm copper busbar 4 runs having three phase Multifunction meter with line indicators and with all necessary accessories with all other connected works etc. The panel made up of 16/18 SWG CRCA sheet steel comprising of 4 sections with separate sheet steel weatherproof and shock proof safety insulation system conforming to IE Rules with IP protection, and with the panel should be painting by powder coating finishing etc.,as complete and making good of the panel with neat finishing. (Switch make : L & T / ABB) panel should be earthing confirming ISI specifications. The rate also includes labour charges and transportation charges etc. The panel should be erected on Anchor fastners, bolts and nuts for mounting the Indoor Panel as directed by engineer-in charge/department superior engineers

1ø & 3ø & DISTRIBUTION BOARD's

HORIZONTAL THREE PHASE MCB DISTRIBUTION BOARD WITH MCB's : Supply and fixing of 7 segment 6 way 63A FP MCB sheet steel Horizontal Distribution Board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single /three phase MCB outgoings and separate 4 way provision for accommodating one no. 4 pole incoming 63 A FP MCB, 10kA, and another separate 4 way for accommodating one no. 63 Amps 4 pole MCB/ ELCB / RCD (totally 8 ways in one segment) ( 3x4ways in each segment ) and Seperate Provision for MCB / Isolators (totally 12nos) for sub incomers in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. i.63A 4Pole MCB - 1no. Incoming ii.32A 2Pole MCB - 3nos. Intermediate iii.20A SP MCB - 18nos Outgoing.

VERTICAL THREE PHASE MCB DISTRIBUTION BOARD WITH MCB : Supply and fixing of 4 way vertical TPN MCCB sheet steel Industrial Type TPN MCCB DB with IP54 Protection of surface type fitted with bus bars and neutral links with 1No. of 100A FP MCCB as Incoming and 12 Nos.of 32A,10KA Triple Pole MCB in Flush with wall and making good of the concealed portion with earth connection.( Industrial Type TPMCCB DB with IP54 Protections)

Supply and fixing of 8way Single pole and neutral MCB sheet steel enclosure with IP 42 protection distribution board with 1no. 32A DP MCB as incoming and 6 Nos of 20A SP MCB for Outgoing in flush with wall with earth connection only. The MCB DB and MCB's should be with ISI mark.

Indoor & Outdoor Lights

Supply and Fixing of 24w LED 2x2 Square type fitting with LED (Higher End) on ceiling with suitable support from ceiling with TW round block with coches screws mounting the fitting on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting. ( Reputed Make like : Philips / Crompton / wipro ) ( Data - 10 )

Supply and fixing of 20W Spot Light LED fittings recessed mounted accent lighting luminaire with die cast aluminium heat sink and sand graind finishing reflector with DALI dimmable driver. and narrow, medium and wide beam optics with CCT option of 3000K to 5000K. Housing colour optionof white and black. The light fitting connected with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete. ( Make : Philips )

Supply and Fixing of 18w LED Round type fitting with LED (Higher End) on ceiling with suitable support from ceiling with TW round block with coches screws mounting the fitting on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting. ( Reputed Make like : Philips / Crompton / wipro )

Supply and fixing of 18W LED 2 ft mirror light on wall with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of LED Strip Profile Shine Light with suitable LED Driver on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the light.

Supply and fixing of 4Feet LED 20W Fitting with LED 20Wtube (Higher End) complete with TW round blocks on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting. ( Reputed Make like : Philips / Crompton / wipro ).

Supply and fixing of pressure die cast aluminium housing WT Bulk Head fitting with guard suitable for 15W LED, IP65 protected with PVC unsheathed copper leads from terminals to the fitting. (Philips/Bajaj/Crompton/K.Lite ).

Supply and fixing of 400mm HS wall mounting fan complete on wall with necessary accessories etc., complete.

Supply and fixing of 1200mm (48") sweep AC Ceiling fan 5star rated complete (Higher end) with 2module 100w fan step regulator (Higher end) with 1meter down rod with fan clamp with side plates and cross arm of size 450mm (18").

Supply and Fixing of 300mm (12") sweep ( Heavy duty ) AC Exhaust fan complete with necessary wall opening and making good of the wall.,

Supply and Fixing of louvers shutters arragements for 300mm (12") sweep ( Heavy duty ) AC Exhaust fan.

Supply and Laying of 3 1/2C x 95 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Clamping of 31/2 C x 35 Sq.mm PVC armoured LTUG aluminium cable on post or on wall with MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable. (SD-206)

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

Supply and fixing of brass cable gland suitable for 31/2C x 95Sq.mm PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland suitable for 31/2C x 35Sq.mm PVC armoured LTUG cable with earth connection. (SD-165)

Supply and providing cable end termination of the following size PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and providing cable end termination of 31/2 C x 95sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 31/2 C x 35sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

COPPER CONDUCTOR

Supply and Run of 4 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 2 Run x 2.5 sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable Pvc conduit pipe on concealed wall and ceiling and 1R of 1.5sq sqmm continuous earth wire connection with painting of suitable colour.

Supply and Run of 2 Run x 1.5 sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable Pvc conduit pipe on concealed wall and ceiling with continuous and 1R of 1.0sq sqmm earth wire connection with painting of suitable colour.

Light / Fan / Staircase / Plug / Points

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / Fan point (for electronic regulator) ( 6points / Coil) Higher End.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1.5 sq.mm. copper wire with painting of suitable colour for Open PVC Light point / Fan point (for electronic regulator) ( 6points / Coil) Higher End.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & pumproom, etc.).

Wiring with 3Rx1.5 sq.mm. (22/0.3) PVC insulated Single core unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1 run of 1.5 Sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Pipe Stair Case Light point (Higher End).

Wiring with 2Rx1.5 sq.mm. (22/0.3) PVC insulated Single core unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 1no. 6A one way module switch and 1no. 6A 3/2 Pin module socket with module front plate with continuous earth wire connection of 1 run of 1.5 Sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Pipe 5A Plug Point ( Higher End ) ( 8 Points / Coil ).

Wiring with 2Rx1.5 sq.mm. (22/0.3) PVC insulated Single core unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with suitable Module Plastic Surface mounting switch box on wall with 1no. 6A one way module switch and 1no. 6A 3/2 Pin module socket with module front plate with painting of suitable colour with continuous earth wire connection of 1 run of 1.5 Sq.mm copper wire for Open PVC Conduit Pipe 5A Plug Point ( 8 Points / Coil ) ( Higher End ).

Wiring with 2Rx4sq.mm PVC insulated Single core unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module Plastic switch box in flush with wall with 1no. 16A one way module switch and 1no. 16A 3/2 Pin module socket with module front plate with continuous earth wire connection of 4.0Sq.mm copper wire and making good of the concealed portion with painting of suitable colour for Concealed PVC Pipe 15A Power Plug Point ( 8 Points / Coil ) ( Higher End ).

SWITCH & SOCKETs

Supply and fixing of 20A Flush type Wall Socket 32A DPMCB complete set for AC Plug in flush with wall with earth connection. ( For AC Plug )

Supply and fixing of 1no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting, grouting, flushing with wall. with connections Higher End. (SD 378 )

Supply and fixing of 1no. TV Socket in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End. ( Make: Havells Crabtree or equivalent )

EARTHING SYSTEM

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp and with copper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply, fabrication, of GI earth flat and copper wire of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with termination in the earth pits, Panels, Distribution boards and equipments with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

Supply and run of 25mm x 3mm Copper flat with necessary clamps / supports on wall /floor /ground for earth connection.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and Run of 25mm dia Pvc conduit pipe on concealed wall with painting of suitable colour. The rate is inclusive of labour charges and transport charges etc., complete.

High Mast

Design, Supply, Erection, Testing and Handing over of High Mast Structure Bajaj/Philips/Make or Equivalent with required number of continuously tapered hot dip galvanized steel polygonal sides sections with telescopic strip joints to a total height of 16 meters capable of sustaining the maximum wind pressure at the erection site with single flange base plate secured welded in the bottom of the base mast section with vertically movable hot dip galvanized lantern carriage and accessories such as electrical junction box brackets for providing 8Nos of flood light luminaries

with motorised control gear box complete head frame assembly, Pulley drive, Stainless steel wire rope single/ double drum self lubricating winch arrangment suitable for raising and lowering the luminaries carriage ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and anchor plates and templates including supply and fixing the following accessories in the Mast as per CEIG rules. a)Design and casting of suitable foundation with 1:2:4 mix RCC conrete with 30cm projection above the ground level with 1metre widthx1 metre length and 2 metre depth with necessary galvanized foundation bolts nuts and washers and dump plate enclosing the bolts for the High Mast considering the safe soil bearing capacity at site - 1 Set b) High powered power tool complete with hand held control panel and motor with push button type remote control switch suitable for 3 phase 415V 50 Hz for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch - 1Set c) Feeder pillar box comprising 0.90 m x 0.45m x 1.20m floor angle iron frame with 63A TPN main switch 1No 32A fuse unit 3 Nos 32A power contactor with automatic timer arrangements and reversing starter for the 3 phase motor - 1Set. d) Neon aviation obstruction light

e) 2Nos of special GI earth electrodes with copper plate 300x300x3mm and coppr flat (1"x1/4") inter connection as per ISS complete with earth connection - 1Set f) Hot dip galvanized lightening arrestor - 1No g) Flood light luminaries of specially Heavy type water proof dust proof integral luminaries fitting provided with 8 Nos of 300 Watts LED flood Light fitting Crompton/Philips make or Equivalent with integrated drives, Alglas coated reflectors with cable connection etc, complete as per standard specification.

CCTV SYSTEM

Supply, Installation, Testing and commissioning of 32 channel 2 SATA NVR, with 8TB Hard Disk Drive 2 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency, Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. ( Make : Hikvision / Dahua / CP PLUS )

Supply of 4MP, Internet Protocol fixed BULLET CAMERA/DOME CAMERA (INDOOR & OUTDOOR)with following specification: a) 1/2.5" Progressive Scan CMOS, b) 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) c) Face Detection d) 120dB WDR, e) BLC/3D DNR/ROI, IP67 compliedf f) On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, g) Shutter Speed 1/3 s to 1/100,000 s, h) 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, i) rotate: 0° to 360°, 2.8 mm, j)horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV:124° k) Lens Mount M12 & IR Range I5: up to 50 m, l) Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, m) Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W n) Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. with Camera Stand. (Make: Dahua/Panasonic/CP PLUS)

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 3840 x 2160 / Refresh Rate : 60 Hertz (4K monitor) b) IPS panel, Display : 4K LED /4K HDR Processor X1 / Triluminos PRO / 4K X-Reality PRO / Motion Flow XR 100 / HDR10 / HLG, Dolby Vision c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Sound : 20watts output / 2ch / Bass Reflex Speaker / Dolby Atomos / 2 Full Range (Bass Reflex) (Make: Sony/ LG /Samsung).

Supply and laying of armoured, Singlemode, Thermoplastic Tape Inner Sheathed, PVC type sheathed 6 core Optical Fibre Cable with unique fiber excess length control method provides the cable with excellent mechanical and environmental properties and Cable - 2 Embedded FRP provides tensile strength & Anti-buckling properties. It is processed with Filling jelly - Thixotropic jelly to prevent Water ingress in loose tube.

Fixing and Termination of Optical Fibre Cable Single Point ( Point to Point ) Splicing and arrangement charges.

Supply and fixing of OFC PVC Black Colour Box 1'x 3/4' x2 PVC Black colour Box ( Rate as Per Quotation )

Supply and Clamping of CAT 6 unarmoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply, Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and Fixing of Rack with Accessories -Higher end 4 U Rack and fan extra for the above rack.

Supply and Fixing of Rack with Accessories -Higher end 9 U Rack with LNS unit and fan extra for the above rack.

Supply and fixing of 2 feet CCTV Camera Stand with attachment fittings as follows: * Weather heads and couplings * Cabinet mounting fittings, plates, brackets as needed. * Reinforced couplings for wire entrances to cabinets.

Supply, Erection of 6m Length pole with base plate of size 300x300x12mm as per IS-875 with following specification. Pole Outter dia -76.10mm x 3.65mm Thick x 6 meter with foundation Charges. ( Rate as per quotation )

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hours back up and battery stand .

Supply and fixing of outdoor 4X6 PVC box with 102mmX77mmX102mm with all fixing accessories.

Supply, installation, testing and commissioning of Long Range Wifi Device of following Specification: Networking Interface: (1) GbE RJ45 Port Power Method: PoE+, Pasive poE(48V) Max TX power: 2.4 GHz Antenna gain: 2.4 GHz Mounting: Wall or Ceiling Mounting Wifi Satndards : 802.11a/b/g Wireless security: WPA-PSK, WPA- Enterprises(WPA/WPA2/WPA3) VLAN: 802.1Q Concurrent Clients: 300+

2.0 T.R capacity 3 Star Split AC

5 KVA voltage Authomatic Voltage Stablizer

Out door base stand for Split Ac

5/8" and 3/8" Copper 3 Core

S & F water drain pipe line

Safety Accessories

Supply of 5m x 4m Rubber 3mm thick Mat suitable for LT installation confirming to IS.

Supply of First Aid Box complete with all First Aid Medicines.

Supply of Shock Treatment Chart fixed in glass frame.

Supply of 4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle.

Supply of Hand Gloves 11KVGrade.

Supply of Danger Board as required by the Electrical Authorities.

Supply of Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms.

Gym Equipments

Supply, installation, testing & commissioning of commercial-grade motorized treadmill with 3.0 HP continuous-duty AC motor , 6-LED display showing speed, incline, distance, time, heart rate & calories; speed 1–18 km/h (min), incline 0–15% (motorized), running deck ≥1400 × 520 mm, 2.0–3.0 mm multi-ply belt with shock absorption, max user weight ≥150 kg, emergency stop & safety key, hand pulse sensors & wireless HR receiver, preset programs (≥12), automatic belt lubrication/maintenance access; frame heavy-gauge steel with rollers, power 230 V, 50 Hz, single-phase; inclusive of delivery, placement, stabilizer, all cabling, testing, commissioning, on-site demo, 12-month comprehensive warranty; makes: Impulse/PowerMax /Matrix/Spirit or equivalent.

Supply, installation, testing and commissioning of commercial grade Elliptical Cross Trainer with electromagnetic resistance system (≥20 levels), stride length not less than 20” (510 mm), flywheel ≥9 kg, maximum user weight capacity ≥150 kg, dual action handlebars with contact heart rate sensors and wireless HR receiver, LED display showing speed, distance, time, calories, resistance level & heart rate, with ≥12 preset workout programs, heavy-gauge steel frame with transport wheels, non-slip pedals, power supply 230 V, 50 Hz, single phase, inclusive of delivery, placement, electrical connection, testing, commissioning, on-site demo, 12-month comprehensive warranty; makes: Matrix / Spirit / Impulse / PowerMax or equivalent.

Supply, installation, testing and commissioning of commercial grade Upright Bike with electromagnetic resistance system (≥20 levels), flywheel ≥9 kg, maximum user weight capacity ≥150 kg, adjustable seat and handlebars, contact heart rate sensors and wireless HR receiver, LED display showing speed, distance, time, calories, resistance level & heart rate, with ≥12 preset workout programs, heavy-gauge steel frame with transport wheels, non-slip pedals with adjustable straps, power supply 230 V, 50 Hz, single phase, inclusive of delivery, placement, electrical connection, testing, commissioning, on-site demo, 12-month comprehensive warranty; makes: Matrix / Spirit / Impulse / PowerMax or equivalent.

Supply, installation, testing and commissioning of commercial grade Recumbent Bike with electromagnetic resistance system (≥20 levels), flywheel ≥9 kg, maximum user weight capacity ≥150 kg, ergonomically designed seat with adjustable backrest, side handlebars with contact heart rate sensors and wireless HR receiver, LED display showing speed, distance, time, calories, resistance level & heart rate, with ≥12 preset workout programs, heavy-gauge steel frame with transport wheels, non-slip pedals with adjustable straps, power supply 230 V, 50 Hz, single phase, inclusive of delivery, placement, electrical connection, testing, commissioning, on-site demo, 12-month comprehensive warranty; makes: Matrix / Spirit / Impulse / PowerMax or equivalent.

Functional Trainer (Dual Adjustable Pulley) Supply, installation, testing and commissioning of Functional Trainer with dual adjustable pulleys, independent weight stacks (minimum 70 kg each side), adjustable pulley height positions for versatile exercises, multi-grip pull-up bar, sturdy powder-coated steel frame, inclusive of delivery, placement, testing, commissioning, on-site demo, 12-month comprehensive warranty; makes: Matrix / Spirit / Impulse / PowerMax or equivalent.

Supply, installation, testing and commissioning of Combination Cage and Smith Machine with free weight training rack and integrated counterbalanced Smith bar system, safety catches and adjustable bar hooks, sturdy powder-coated frame, inclusive of delivery, placement; makes: Impulse / Spirit / equivalent.

Olympic Multipurpose Bench Supply and installation of Olympic Multipurpose Bench with adjustable backrest and barbell support stands, sturdy powder-coated frame, high-density PU cushions with sweat-resistant upholstery, inclusive of delivery; makes: Impulse / Spirit / PowerMax or equivalent.

Multipurpose Bench (Flat/Incline/Decline) Supply and installation of Multipurpose Adjustable Bench (Flat/Incline/Decline) with adjustable seat/backrest, sturdy frame, high-density PU cushions with sweat-resistant upholstery, inclusive of delivery, demo; makes: Impulse / Spirit / PowerMax or equivalent.

Adjustable Abdominal Bench Supply and installation of Adjustable Abdominal Bench with multiple incline positions, sturdy powder-coated frame, PU padded cushions, inclusive of delivery, demo; makes: Impulse / Spirit / PowerMax or equivalent.

Seated Preacher Curl Supply and installation of Seated Preacher Curl Bench with angled arm pad, adjustable seat height, sturdy frame, PU cushions, inclusive of delivery, demo, 12-month warranty; makes: Impulse / Spirit / PowerMax or equivalent.

Utility Bench Supply and installation of Utility Bench with fixed seat and back pad for dumbbell/shoulder exercises, sturdy frame, PU cushions, inclusive of delivery, demo, 12-month warranty; makes: Impulse / Spirit / PowerMax or equivalent.

Flat Bench - 4 Feet Supply and installation of Flat Bench with fixed horizontal cushion, sturdy frame, PU upholstery, inclusive of delivery, demo, 12-month warranty; makes: Impulse / Spirit / PowerMax or equivalent.

Round Dumbbells Supply and delivery of commercial grade Round Dumbbells (rubber coated, fixed weight), precision balanced, steel handles with knurled grip, available in standard increments, inclusive of delivery, 12-month warranty; makes: Afton / Impulse / Spirit or equivalent.

Dumbbell Rack – 5 Feet Supply and installation of 5 Feet Dumbbell Rack, 2-tier design, heavy-duty steel frame with powder coat finish, inclusive of delivery, demo, 12-month warranty; makes: Afton / Impulse / Spirit or equivalent.

Fusion Plates Supply and delivery of Fusion Plates (Olympic size, rubber encased, tri-grip design), inclusive of delivery, 12-month warranty.

Plate Stand Supply and installation of Olympic Plate Stand (vertical or tree type), heavy-duty steel frame with powder coating, inclusive of delivery, demo, 12-month warranty.

Olympic Rod – 7 Feet Supply and delivery of Olympic Barbell 7 Feet, chrome finish, 20 kg weight, knurled grip, 50 mm sleeve diameter, inclusive of delivery, 12-month warranty.

EZ Rod Olympic – 4 Feet Supply and delivery of Olympic EZ Curl Bar 4 Feet, chrome finish, knurled grip, 50 mm sleeve diameter, inclusive of delivery, 12-month warranty.

Deadlift Platform Supply and installation of Deadlift Platform with solid wood center and rubber side strips for shock absorption, steel frame edging, inclusive of delivery, demo, 12-month warranty.

Bumper Plate Set Supply and delivery of Bumper Plate Set (Olympic size, rubber coated, color coded by weight, shock-absorbent), inclusive of delivery, 12-month warranty.

SHRINIDHI INFRRA (BID ID -1537632)

LOTUS CONSTRUCTION (BID ID -1537204)