REPAIR/ MAINT OF DG SETS, SUMBERSIBLE PUMPS AND MOTORS, STATORS, SUPPLY OF DRINKING WATER TREATMENT CHEMICALS AND ALLIED WORKS AT AYODHYA CANTT

Amount

Periodical maintenance for entire duration of contract including complete servicing of Diesel Engine Generator set of 160 KVA capacity at Military Hospital of make: Kirloskar or any other make as per site requirement and connected accessories including replacement of oil /lubricant filter to keep the plant in running condition including routine maintenance complete all as specified and as directed. [Note: (i) The Contractor need to get the job done through authorised service centre/ agency of Kirloskar Oil Engine Ltd or any other OEM (Original Equipment Manufacturer) located near Faizabad. The cost thereof deemed to be included in the quoted rate. (ii) All Spare parts for routine maintenence will be measured and paid separately under relevent items of this schedule as 'Supply Only' (iii) Labour charges for routine maintenance including properly dismantling of old parts deemed to be included in the quoted rate]

All as per Ser Item No 1 here in above but of Diesel Engine Generator Set of 62.5/ 63 kVA capacity at Pump House No 1, 2, 3, 4, 5,6,7, 8, 9, 10, 11, 12, STP Himachal Niwas, STP Kandahar Line, Signal Centre, Amn Dump, Trolly Mounted, OGP,Sainik Sadan complete all as specified and directed

All as per Ser Item No 1 here-in-above but of Diesel Engine Generator Set of 40 KVA capacity at Records complete all as specified and directed

All as per item Ser No 1 here-in-above but of Diesel Engine Generator Set of 15 KVA capacity complete all as specified and directed

Supply only Lubricant oil filter for routine maintenance of DG Set 160 KVA, complete all as specified and directed

All as per item No.5 here in above but Fuel filter (Pre) complete all as specified and directed

All as per item No.5 here in above but Fuel filter (Micro) complete all as specified and directed

All as per item No.5 here in above but Air filter outer complete all as specified and directed

All as per item No.5 here in above but Air filter inner complete all as specified and directed

Supply only Lubricant oil filter for routine maintenance of 15-62.5 KVA DG Set complete all as specified and directed

All as per item No.10 here in above but Fuel filter (Pre) complete all as specified and directed

All as per item No.10 here in above but Fuel filter (Micro) complete all as specified and directed

All as per item No.10 here in above but Air filter outer complete all as specified and directed

All as per item No.10 here in above but Air filter inner complete all as specified and directed

Supply only Coolant for DG Set complete all as specified and directed

Supply only Lub Oil for DG Set of make Koel Care Premium Genuine complete all as specified and directed

M&L for Head Gasket set (Cylinder head) of capacity 160 KVA DG set complete all as specified and directed Make: Kirloskar or equivalent all as specified and directed. (Labour charges for properly dismantling of old parts deemed to be included in the quoted rate)

All as per item No.17 here in avove but Valve Inlet-Exhaust complete all as specified and directed

All as per item No.17 here in above but Seat Inlet-Exhaust complete all as specified and directed

All as per item No.17 here in above but Valve Guide complete all as specified and directed

All as per item no.17 here in above but Valve Collet complete all as specified and directed

All as per item no.17 here in above but Valve Spring complete all as specified and directed

All as per item no.17 here in above but Piston Assembly complete all as specified and directed

All as per item no.17 here in above but Piston Ring set complete all as specified and directed

All as per item no.17 here in above but Cylinder linear complete all as specified and directed

All as per item no.17 here in but O-Ring complete all as specified and directed

All as per item no.17 here in above but Tappet bush with packing complete all as specified and directed

All as per item no.17 here in above but Thermostat assembly complete all as specified and directed

All as per item no.17 here in above but Sealing ring set complete all as specified and directed

All as per item no.17 here in above but Rocker lever complete all as specified and directed

All as per item no.17 here in above but Rocker BRKT complete all as specified and directed

All as per item no.17 here in above but Push rod complete all as specified and directed

All as per item no.17 here in above but Push rod tube complete all as specified and directed

All as per item no.17 here in above but Alternator coupling complete all as specified and directed

All as per item no.17 here in above but Starter Ring complete all as specified and directed

All as per item no.17 here in before but Oil level pressure and level gauge/indicator complete all as specified and directed

All as per item no.17 here in before but Amp meter indicator for battery charging complete all as specified and directed

All as per item no.17 here in before but Digital panel board indicating volt,current,pf,kw complete all as specified and directed

All as per item no.17 here in before but CT 100/5 complete all as specified and directed

All as per item no.17 here in before but ON/ Off push button set complete all as specified and directed

All as per item no.17 here in before but Cut out for charging alternator complete all as specified and directed

All as per item no.17 here in before but Ignition Switch for charging alternator complete all as specified and directed

All as per item no.17 here in before but Switch Plate for charging alternator complete all as specified and directed

All as per item no.17 here in before but Diode Plate forcharging alternator complete all as specified and directed

All as per item no.17 here in before but Carbon for charging alternator complete all as specified and directed

All as per item no.17 here in before but Bulb Holder for charging alternator complete all as specified and directed

All as per item no.17 here in before but Rectifier Assembly for charging alternator complete all as specified and directed

All as per item no.17 here in before but Brush Box Assembly for charging alternator complete all as specified and directed

All as per item no.17 here in before but Bearing for charging alternator complete all as specified and directed

All as per item no.17 here in before but Oil seal for charging alternator complete all as specified and directed

All as per item no.17 here in before but Field Coil for charging alternator complete all as specified and directed

All as per item no.17 here in before but Hose Water Pump inlet to Radiator outlet complete all as specified and directed

All as per item no.17 here in before but Hose Pipe to Water Pump complete all as specified and directed

All as per item no.17 here in before but Hose Pipe to Diesal tank complete all as specified and directed

All as per item no.17 here in before but Hose pipe with 04 nos clip & nut complete all as specified and directed

All as per item no.17 here in before but Terminal block complete all as specified and directed

All as per item no.17 here in before but Fan Belt complete all as specified and directed

All as per item no.17 here in before but Automatic Voltage Regulator complete all as specified and directed

All as per item no.17 here in before but Water Pump Repair Kit complete all as specified and directed

M&L for Head Gasket set (Cylinder head) of capacity 15-63 KVA DG set make: Kirloskar or equivalent all as specified and directed. [Labour charges for properly dismantling of old parts deemed to be included in the quoted rate]

All as per item No.60 here in above but Valve Inlet-Exhaust complete all as specified and directed

All as per item No.60 here in above but Seat Inlet-Exhaust complete all as specified and directed

All as per item No.60 here in above but Valve Guide complete all as specified and directed

All as per item No.60 here in above but Valve Collet complete all as specified and directed

All as per item No.60 here in above but Valve Spring complete all as specified and directed

All as per item No.60 here in above but Piston Assembly complete all as specified and directed

All as per item No.60 here in above but Piston Ring set complete all as specified and directed

All as per item No.60 here in above but Cylinder linear complete all as specified and directed

All as per item No.60 here in above but O-Ring complete all as specified and directed

All as per item No.60 here in above but Tappet bush with packing complete all as specified and directed

All as per item No.60 here in above but Thermostat assembly complete all as specified and directed

All as per item No.60 here in above but Sealing Ring set complete all as specified and directed

All as per item No.60 here in above but Rocker lever complete all as specified and directed

All as per item No.60 here in above but Rocker BRKT complete all as specified and directed

All as per item No.60 here in above but Push rod complete all as specified and directed

All as per item No.60 here in above but Push rod tube complete all as specified and directed

All as per item No.60 here in above but Alternator coupling complete all as specified and directed

All as per item No.60 here in above but Starter Ring complete all as specified and directed

All as per item No.60 here in above but Expansion bellow complete all as specified and directed

All as per item No.60 here in above but Oil level pressure and level gauge/indicator complete all as specified and directed

All as per item No.60 here in above but Amp meter indicator for battery charging complete all as specified and directed

All as per item No.60 here in before but Digital panel board indicating volt,current,pf,kw complete all as specified and directed

All as per item No.60 here in before but CT 100/5 complete all as specified and directed

All as per item No.60 here in before but ON/ Off push button set with wiring complete all as specified and directed

All as per item No.60 here in before but Cut out for charging alternator complete all as specified and directed

All as per item No.60 here in before but Ignition Switch for charging alternator complete all as specified and directed

All as per item No.60 here in before but Switch Plate for charging alternator complete all as specified and directed

All as per item No.60 here in before but Diode Plate forcharging alternator complete all as specified and directed

All as per item No.60 here in before but Carbon for charging alternator complete all as specified and directed

All as per item No.60 here in before but Bulb Holder for charging alternator complete all as specified and directed

All as per item No.60 here in before but Rectifier Assembly for charging alternator complete all as specified and directed

All as per item No.60 here in before but Brush Box Assembly for charging alternator complete all as specified and directed

All as per item No.60 here in before but Bearing for charging alternator complete all as specified and directed

All as per item No.60 here in before but Oil seal for charging alternator complete all as specified and directed

All as per item No.60 here in before but Field Coil for charging alternator complete all as specified and directed

All as per item No.60 here in before but Hose : Water Pump inlet to Radiator outlet complete all as specified and directed

All as per item No.60 here in before but Hose :Pipe to Water Pump complete all as specified and directed

All as per item No.60 here in before but Hose : Pipe to Diesal tank complete all as specified and directed

All as per item No.60 here in before but Hose pipe with 04 nos clip & nut complete all as specified and directed

All as per item No.60 here in before but Terminal block complete all as specified and directed

All as per item No.60 here in before but Fan Belt complete all as specified and directed

All as per item No.60 here in before but Automatic Voltage Regulator complete all as specified and directed

All as per item No.60 here in before but Water Pump Repair Kit complete all as specified and directed

S&F stranded copper conductor battery lead 25 Sqmm for 24 volts DC grade red for (+)ve terminal and black for ( -)ve terminal i.e. 02 nos fitted with battery terminal at one end and battery lug at other end complete length 1.5 mtr, complete all as specified and directed.

M&L for Calibration of Fuel Injection Pump including properly dismantling and transporting to service center/workshop for over hauling/ calibration and refixing on DG Set after calibration for DG Sets of capacity 160 kVA including taking out of old one and with replacement of following items all as directed by Engr -in charge :a) Element - 06 Nos b) D.V - 06 Nos c) T.R.B - 06 Nos d) Bearing - 02 Nos e) C.R - 01 Nos f) C.R Bush - 02 Nos g) Ball Bearing - 01 Nos h) F.P.P - 01 Nos i) F.P Kit - 01 Nos j) Pressure Bolt - 06 Nos k)Nozzle seal - 02 Nos l) Nozzle setting - 06 Nos & with all other neessary items .

All as per item No.105 here in above but for DG Sets of capacity 62.5/ 63 KVA complete all as specified and directed

All as per item No.105 here in above but for DG Sets of capacity 40 KVA complete all as specified and directed

All as per item No.105 here in above but for DG Sets of capacity 15 KVA complete all as specified and directed

M&L for Banjo Bolt M 14 x 1.5 including taking out of old one complete all as specified and directed

M&L for Flexible fuel pipe type 7.5 14 x 14 B 700 PB complete all as specified and directed Make: Kirloskar or equivalent including taking out of old one

M&L for Fuel Pump mounted STOP solenoid switch suitable for 15 to 62.5-63 KVA DG set complete all as specified and directed Make: Kirloskar or equivalent including taking out of old one.

M&L for servicing of radiator including cleaning and testing of leakages for DG set of capacity 160 KVA complete all as specified and directed [Note: - In case of leakages found during servicing, the same should be measured and paid separately ]

All as per item No.112 here in above but for DG set capacity 15-63 KVA complete all as specified and directed

Dismantling the radiator and transporting to workshop, repair of all leakage and transporting back and refitting in original position and testing for DG set of capacity 160 KVA complete all as specified and directed

All as per item No.114 here in above but for DG set capacity 15-63 KVA complete all as specified and directed

M&L for Carefully dismantling the alternator of DG set capacity 160 KVA and transporting to workshop for repair and reffiting back the same in its original position after repair and testing complete all as specified and directed.

M&L for Carefully cutting out old burnt armature winding of alternator of DG set capacity 160 KVA, cleaning the slot of stator and rewinding the same with super enamelled copper winding wire of appropriate gauge complete with all insulating materials, nomex paper, copper tape, glass sleeve, soldering rod, grease etc. complete all as specified and directed.

All as per item No.117 here in above but for field winding of alternator complete all as specified and directed

All as per item No.117 here in above but for exciter coil of alternator complete all as specified and directed

M&L for Carefully dismantling the alternator of DG set capacity 40-63 KVA and transporting to workshop for repair and reffiting back the same in its original position after repair and testing complete all as specified and directed.

M&L for Carefully cutting out old burnt armature winding of alternator of DG set capacity 15-63 KVA, cleaning the slot of stator and rewinding the same with super enamelled copper winding wire of appropriate gauge complete with all insulating materials, nomex paper, copper tape, glass sleeve, soldering rod, grease etc. complete all as specified and directed.

All as per item Ser No 121 above but for field winding of alternator complete all as specified and directed

All as per item Ser No 121 above but for exciter coil of alternator complete all as specified and directed

All as per item Ser No 121 above but damaged ball bearing(S.K.F.) complete all as specified and directed

M&L for Carefully dismantling the alternator of DG set capacity 15 KVA and transporting to workshop for repair and reffiting back the same in its original position after repair and testing complete all as specified and directed.

M&L for Carefully cutting out old burnt armature winding of alternator of DG set capacity 15 KVA, cleaning the slot of stator and rewinding the same with super enamelled copper winding wire of appropriate gauge complete with all insulating materials, nomex paper, copper tape, glass sleeve, soldering rod, grease etc. complete all as specified and directed.

All as per item No.126 here in above but for field winding of alternator complete all as specified and directed

All as per item No.126 here in above but for exciter coil of alternator complete all as specified and directed

All as per item No.126 here in above but damaged ball bearing(S.K.F.) complete all as specified and directed

M&L for Carefully dismantling the fuel tank and transporting to workshop, repair of all leakage, cleaning and transporting back and refitting in original position and testing after completion for DG set of capacity 160 KVA complete all as specified and directed including taking out of old one.

All as per item No.130 here in above but for DG set capacity 15-63 KVA complete all as specified and directed

M&L for Carefully cleaning of fuel tank for DG set of capacity 160 KVA complete all as specified and directed including taking out of old one.

All as per item No.132 here in above but for DG set capacity 15-63 KVA complete all as specified and directed

S&F self starter of DG set of capacity 160 KVA 12/24 volts of any make and model compatible with the existing one complete all as specified and directed

All as per item No.134 here in above but for DG Sets of capacity 62.5/ 63 KVA complete all as specified and directed

All as per item No.134 here in above but for DG Sets of capacity 40 KVA complete all as specified and directed

All as per item No.134 here in above but for DG Sets of capacity 15 KVA complete all as specified and directed

M&L for Carefully dismantling the self starter of DG set capacity 62.5/63 KVA and transporting to workshop and reffiting back after repair with replacement / repair of following items complete all as specified and directed

Supply only Carbon bush with spring materials for repair of self starter of DG set capacity 15-160 KVA, complete all as specified and directed

All as per item No.139 here in above but GM Bush set complete all as specified and directed

All as per item No.139 here in above but Bendex Pinion complete all as specified and directed

All as per item No.139 here in above but Solenoid Switch complete all as specified and directed

All as per item No.139 here in above but Armature Rewinding complete all as specified and directed

All as per item No.139 here in above but Field Coil set complete all as specified and directed

Supply only lead acid battery 12 volt 150 Ah including initial charge of make: Exide or equivalent complete all as directed by Engr-In-Charge

M&L Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, connected with GI strip 25x4mm by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI strip is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horizontally to the equipment. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded ....contd to item No-146.01

stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm complete all as specified and directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009).

Supply only earth lead GI strip 25x4mm complete all as specified and directed

S&F for MCCB 3 pole 100 Amp, 415 volt, 25 KA complete all as specified and directed Make: L&T or equivalent in C&S, Scheinider,siemens in existing panel including taking out of old one complete all as specified and directed by Engr-in-charge.

S&F for MCCB 4 pole 100 Amp, 415 volt, 25 KA of Make: L&T or equivalent in C&S, Scheinider,siemens in existing panel including taking out of old one complete all as specified and directed by Engr-in-charge.

S&F for On load Changeover 4 pole 100 Amp, 415 volt, in sheet steel enclosure type of Make: L&T or equivalent including taking out of old one complete all as specified and directed by Engr-in-charge.

S&F for On load Changeover 4 pole 100 Amp, 415 volt, open execution type of Make: L&T or equivalent in C&S, Scheinider,siemens in existing panel including taking out of old one complete all as specified and directed by Engr-in-charge.

S&F for Single phase Preventer Relay with adjustable time delay 30 sec to 5 min suitable for 415 volt AC, any type of Make: L&T or equivalent including internal wiring from switchgear to relay in existing panel all as specified and as directed by Engr-in-charge.

S&F for 3 pole power contactor MNX 70, 220/440 volts with 70 Amp AC3 duty rating any type including auxillary switch of make: L&T or equivalent in existing panel including taking out of old one complete all as specified and directed by Engr-in-charge.

S&F for 3 pole power contactor MNX 50, 220/440 volts with 50 Amp AC3 duty rating any type including auxillary switch of make: L&T or equivalent in existing panel including taking out of old one complete all as specified and directed by Engr-in-charge.

S&F for digital type Voltmeter with LED display suitable for 3 phase of make: L&T or equivalent in existing panel including taking out of old one complete all as specified and directed by Engr-in-charge.

S&F for digital type Ammeter with LED display suitable for 3 phase make: L&T or equivalent in existing panel including taking out of old one complete all as specified and directed by Engr-in-charge.

M&L for fixing of DOL starter three phases 415 Volt for 2.5 HP electric motor including all fixing materials complete all as specified and directed

M&L for fixing of DOL starter three phases 415 Volt for 7.5 HP electric motor including all fixing materials complete all as specified and directed

Supply & Fixing of Flat three core submersible cable PVC insulated and sheathed multistranded copper conductor of cross sectional area 16 sqmm complete all as specified and directed of make: Havells , Kalinga ,Polycab or equivalent .

S&F for FR PVC Insulated Single core unsheathed Industrial Flexible cable of size 16 sqmm conforming to IS 694:2010 with bright annealed copper conductor in existing panel including taking out of old one complete all as specified and directed Make : Polycab or equivalent .

Supply only bleaching powder in 25 Kg bag (ISI marked) grade II complete all as specified and directed by Engr-In-Charge (Make: Punjab Alkalies/Modi Alkalies/Sriram as approved).

Supply only sodium hypochloride liquid (chlorine content 10%) duly packed in sealed drum of make: M/s Declibac/ M/s Rayalshima Enterprise/ Birla Chemicals or equivalent complete all as specified and directed

Dismantling of defective chlorination reciprocating plants any make & model of pressure rating 10 Kg/cm2 and discharge upto 6 LPH, repairing the same including replacing old unserviceable parts and re-assembling and testing after repair complete all as specified and directed by Engr-In-Charge. [Note: (i) All the spares required for repair will be measured and paid separately as supply only.]

Supply only self priming metering chlorination reciprocating dosing pump with max pressure rating 10 Kg/cm2 and discharge upto 6 LPH adjustable including solenoid coil with body,pulsar circuit,speed/stroke knob etc any make & model complete all as specified and directed by Engr-in-charge.

All as per item No.166 here in above but Solenoid coil with body complete all as specified and directed

All as per item No.166 here in above but Pulsar circuit complete all as specified and directed

All as per item No.166 here in above but Speed/ stroke knob complete all as specified and directed

All as per item No.166 here in above but PVC Injection check valve(NRV) 3/4'' with PVDF housing and Viton O-rings ' complete all as specified and directed

All as per item No.166 here in above but LDPE Dosing tube 3/8''x1/4'' complete all as specified and directed

All as per item No.166 here in above but Suction/discharge valve PVC complete all as specified and directed

All as per item No.166 here in above but Head (P P) complete all as specified and directed

All as per item No.166 here in above but Pan head screw 3/16 x 3/4'' complete all as specified and directed

All as per item No.166 here in above but Teflon faced diaphragm complete all as specified and directed

All as per item No.166 here in above but PVC Foot valve 3/4'' assembly complete all as specified and directed

All as per item No.166 here in above but Coupling nut complete all as specified and directed

All as per item No.166 here in above but Ceramic Ball complete all as specified and directed

All as per item No.166 here in above but NRV spring complete all as specified and directed

All as per item No.166 here in above but teflon ring seal complete all as specified and directed

M&L for chlorine ppm comparator test Kit with colour indicators having 0.1 to 2.0 PPM with Resolution 0.01 pH, make:Avon/ Aquasol or equivalent.

Supply only Liquid O-Tolidine solution in sealed bottle of 500 ml complete all as specified and directed

Taking out steel/ UPVC water tubing for 20 mm bore size including fittings complete all as specified and directed by Engr-in-charge

M&L for Unplasticised PVC pipes Sch 40 of fixed complete to walls, ceilings or in floors etc., any type of pipe for 20 mm bore sizes make: ISI Marked best quality etc complete all as specified and directed by Engr-in-charge

M&L for 20 mm CPVC ball valve complete all as specified and directed

M&L for 20 mm CPVC Union complete all as specified and directed

M&L for gun metal globe or gate valve 'ISI marked' with iron wheel head screwed both end for iron pipe all as per latest IS specifications of the size 15 mm complete all as specified.

All as per item No.187 here in above but 20 mm bore complete all as specified and directed

S&F in replacement of suction sweeper stainless steel not less than 3 feet long comprising 600mm suction head spring loaded twin brush with PVC wheels, and fiber squeezer complete all as specified and directed Engr-in-charge.

Supply only Nylon-Rope size (14 -20) mm dia suction sweeper , complete all as specified and directed

Supply only PVC suction hose / pipe, green (1-2" ultra Light & flexible with PVC spiral ribbed for extra strength) with 2 male connector nipplesplus clamps (4 Nos.) complete all as specified and directed

Collection of water samples of bore wells located in deferent pockets of cantonment area in decontaminated sterilised bottles and testing of water samples for following essential parameters for drinking water as per IS:10500- 2012 from Govt Lab or NABL accredited laboratory: -(i) Colour (ii) odour (iii) taste (iv) pH value, (v) Turbidity (vi) TDS (vii) Total arsenic (viii) Silica (ix) Fluoride (x) Iron (xi) Magnesium (xii) Sulphate (xiii) Total Hardness (xiv) Total alkalinity (xv) Calcium (xvi) Conductivity (xvii) Chloride (xviii) Total Coliform and (xix) E Coli complete all as specified and directed

M&L for Rolled mild steel in Joist ,channel,angle, or tee sections, fixed independently, without connecting plates, etc. for repair to staircase,hand rails and back rest of over head reservoir or as otherwise directed. [Note: All T&P and labour charges for working on OH tanks upto 21 mtr high staging deemed to be included in the quoted rate]

Lifting of defective submersible pump set any make & model of capacity 25 HP to 45 HP from deep well 350mm housing along with connected accessories such as column pipe of 150mm dia appx 30 m submersible cable, steel pipe, spider, sleeve, line shaft, nut, bolts etc complete all as specified and directed by Engr-In-Charge. [Note:- (i) All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate (ii) The Contractor will start the lifting work with in minimum time after getting message verbally/telephonically by JE E/M/AGE E/M. (iii) A penalty of Rs. 500/- per day will be imposed on the Contractor for wilful delay by the Contractor will be imposed as per opinion of Engineer-in-Charge and amount will be deducted from the due payment of the Contractor]

Transportation including loading & unloading of defective submersible pump set 3 phase any make and capacity 25 to 45 HP from pump house to work shop for necessary repair and transporting back to the pump house including carefully loading & unloading of pump set after repair complete all as specified and directed by Engr-In-Charge.

Dismantling of defective submersible pump set any make & model of capacity 25 HP to 45 HP, repairing the same including replacing old unserviceable parts and re-assembling and testing after repair complete all as specified and directed by Engr-In-Charge.[Note: (i) All the spares required for repair will be measured and paid seperately as supply only. (ii) Greasing of moving parts deemed to be included in the quoted rate]

Supply only CI/ MS bowl (As per existing size) for submersible pump capacity 25 HP to 45 HP any make & model complete all as specified and directed

All as per item No.197 here in above but Stainless steel shaft with key complete all as specified and directed

All as per item No.197 here in above but Gun Metal/rubber Bush complete all as specified and directed

All as per item No.197 here in above but Stainless steel sleeve complete all as specified and directed

All as per item No.197 here in above but Sand Guard complete all as specified and directed

All as per item No.197 here in above but Impeller lock with key complete all as specified and directed

All as per item No.197 here in above but Neck ring (as per existing size and type) complete all as specified and directed

All as per item No.197 here in above but Turning & polishing of Pump shaft (lathe work) complete all as specified and directed

Supply only Stainless Steel thrust bearing. parts for submersible motor of capacity 25 HP to 45 HP any make & model complete all as specified and directed

All as per item No.205 here in above but Carbon plate complete all as specified and directed.

All as per item No.205 here in above but Rotor Gun Metal/rubber bush complete all as specified and directed

All as per item No.205 here in above but Rubber bush complete all as specified and directed

All as per item No.205 here in above but Upper housing complete all as specified and directed

All as per item No.205 here in above but Lower Housing complete all as specified and directed

All as per item No.205 here in above but Turning, polishing of Rotor & shaft (Lathe work) complete all as specified and directed

Rewinding of submersible motor capacity 25 HP to 45 HP any make & model with super enamelled copper wire of existing size including removal of existing burnt winding, cleaning of slots including packing material, connection and testing complete all as specified and directed

M&L for painting to pump set with two coat of synthetic enamel paint (grey colour) over a coat of red oxide primer after preparation of surface complete all as specified and directed by Engr-In-Charge.

Lowering, connecting, commissioning testing of repaired submersible set any make and capacity 25 HP to 45 HP 3 phase 415V into bore well 300/200mm with connected items such as column pipe approx 40 RM, properly connecting submersible cable etc complete all as specified and directed by Engr-In-Charge by Engineer-in-Charge. [Note:- (i) All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate (ii) The Contractor will start the lifting work with in minimum time after getting message verbally/ telephonically by JE E/M/ AGE E/M. (iii) A penalty of Rs. 500/- per day will be imposed on the Contractor for wilful delay by the Contractor will be imposed as per opinion of Engineer-in-Charge and amount will be deducted from the due payment of the Contractor]

Complete servicing of Fire fighting pump set any make & model of capacity 60 HP including replacement of minor spares and testing after servicing complete all as specified and directed by Engr-In-Charge. [Note: (i) Greasing of moving parts deemed to be included in the quoted rate (ii) All type of T&P main switch ,electric multi meter/ tong tester for fault detecting , etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.

Supply only rubber packing 6mm thick consisting of 8/6" holes for 100mm to 150 mm dia column pipe complete all as specified and directed by Engr-In-Charge.

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 20 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling belt, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 10 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 7.5 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Repair and maintenance of defective Monoblock motor pump any make & model of capacity upto 2.5 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-In-Charge. [Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.]

Complete servicing of servo voltage stabilizer of 50 KVA of make: Servostar / Vinitec or any other make as per site requirement and connected accessories including replacement of defected old parts, oil / lubricant to keep the plant in running condition including routine maintenance complete all as specified and as directed. [Note: (i) The Contractor need to get the job done through authorised service centre/ agency of OEM (Original Equipment Manufacturer).The cost thereof deemed to be included in the quoted rate. (ii) All Spare parts for routine maintenence will be measured and paid separately under relevent items of this schedule as 'Supply Only' (iii) Labour charges for routine maintenance including properly dismantling of old parts deemed to be included in the quoted rate]

Supply only Variac for routine maintenance of servo voltage stabilizer 50 KVA capacity complete all as specified and directed

All as per item No.222 here in above but servo motors (3 Kg) complete all as specified and directed

All as per item No.222 here in above but RC Network (3 Kg) complete all as specified and directed

All as per item No.222 here in above but Sensor Transformer 8/16V (Triggar) complete all as specified and directed

All as per item No.222 here in above but 2 K Pot complete all as specified and directed

All as per item No.222 here in above but PCB Digital Card (Double Display) complete all as specified and directed

All as per item No.222 here in above but Carbon Brush complete all as specified and directed

All as per item No.222 here in above but Voltmeter complete all as specified and directed

All as per item No.222 here in above but Micro Switch complete all as specified and directed

All as per item No.222 here in above but SPDT & DPDT Switches complete all as specified and directed

All as per item No.222 here in above but Buck Boost Transformer complete all as specified and directed

All as per item No.222 here in above but Motorised Plate complete all as specified and directed

All as per item No.222 here in above but Front Plate Variac complete all as specified and directed

All as per item No.222 here in above but Armer of Variac complete all as specified and directed

All as per item No.222 here in above but Variac Base complete all as specified and directed

All as per item No.222 here in above but Strip 30 Amp complete all as specified and directed

All as per item No.222 here in above but Spring complete all as specified and directed

All as per item No.222 here in above but Hexa complete all as specified and directed

All as per item No.222 here in above but Stopper complete all as specified and directed

All as per item No.222 here in above but Relay 5 Amp complete all as specified and directed

All as per item No.222 here in above but Push Button complete all as specified and directed

All as per item No.222 here in above but LED (Green,Yellow,Red) complete all as specified and directed

All as per item No.222 here in above but PCB Card (High & Low Cut Off) complete all as specified and directed

All as per item No.222 here in above but Transformer Oil complete all as specified and directed

M&L for replacement of old rusted flat iron clamp of size 370 mm length 80 mm width and 6 mm thickness along with 25 / 50 mm hole in centre of the clamp and fixing of 25 / 50 mm socket on clamp for fixing of GI pipe and two holes on each side end of clamp for fixing of nut bolt and washer including smith and lathe work for making the desired curve on flat iron suitable for fixing on 150 mm pipe mains complete all as specified and directed by Engr-in-charge.

M&L for replacement of old rusted flat iron clamp of size 370 mm length 65 mm width and 6 mm thickness along with 20 / 15 mm hole in centre of the clamp and fixing of 20 / 15 mm socket on clamp for fixing of GI pipe and two holes on each side end of clamp for fixing of nut bolt and washer including smith and lathe work for making the curve on flat iron suitable for fixing on 150 mm pipe mains complete all as specified and directed by Engr-in-charge.

M&L for replacement of old rusted flat iron clamp of size 270 mm length 80 mm width and 6 mm thickness along with 25 / 50 mm hole in centre of the clamp and fixing of 25 / 50 mm socket on clamp for fixing of GI pipe and two holes on each side end of clamp for fixing of nut bolt and washer including smith and lathe work for making the curve on flat iron suitable for fixing on 100 mm pipe water mains complete all as specified and directed by Engr-in-charge.

M&L for replacement of old rusted flat iron clamp of size 270 mm length 65 mm width and 6 mm thickness along with 20 / 15 mm hole in centre of the clamp and fixing of 20 / 15 mm socket on clamp for fixing of GI pipe and two holes on each side end of clamp for fixing of nut bolt and washer including smith and lathe work for making the curve on flat iron suitable for fixing on 100 mm pipe water mains complete all as specified and directed by Engr-in-charge.

Attending complaint for rectification of leakage in 150 mm bore DI pipe line with push on joints complete by rubber gasket or flange spigot and socket fitting, any bend or tee including necessary nut bolts & washers etc including excavation for any lenght of pipe by using labour as well as returning,filling complete all as specified and direcrted by Engr-in-charge.

All as per item No.250 here in above but 100 mm bore complete all as specified and directed

Attending complaint for rectification of leakage in 150 mm bore DI pipe line with flanged joints fixed to pillar of RCC overhead reservoir upto 21 meters height or below ground level complete by rubber or fibre board gasket, blank flange with screwing or threading on lathe machine, desired chemicals for leakage inside floor of overhead tanks where pipes are attached including necessary nut bolts & washers etc including excavation by using labour as well as returning,filling complete all as specified and direcrted by Engr-in-charge.

All as per item No.252 here in above but 100 mm bore complete all as specified and directed

Taking up 150 mm bore spigot and socketed pipe with rubber gasket including fittings complete all as specified and directed by Engr-in-charge.(Note- Excavation & earth work shall be measured and paid separately)

M&L for 150 mm bore ductile iron pipes spigot & socket class K-9 'ISI marked' in any length laid in trenches all as specified and directed by Engr-in-charge. (Note - Excavation, earth work and joint shall be measured and paid seperately).

Relaying 150 mm bore ductile iron pipes spigot and socketed ends centrifugally casted class A 'ISI marked' in any length laid in trenches including cleaning of pipe all as specified and directed by Engr-in-charge. (Note - Excavation, earth work and joint shall be measured and paid seperately).

M&L for rubber gasket joints for spigot and socket pipes and fittings of size 150 mm dia complete all as specified and directed by Engr-in-charge.

M&L for specials/fittings of spigot socketed pipes of bore upto 150 mm such as bend, tee, flange ,socket, collar Reducer, Tail Pieces Y junction double ,cross etc complete all as specified and directed by Engr-in -charge.

Excavation in trenches n.exc. 1.5 mtr wide and n.exc. 1.5 mtr in depth for laying / taking out water supply pipe line in soft/loose soil, taking out excavated material,forming bottom etc complete all as specified and directed Engr-in-charge.

Returning filling in including,spreading ,levelling watering and well ramming in layer in n.exc 25 cm in soft/lose soil complete all as specified and directed Engr-in-charge.

Removing excavated material n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above starting point as in soft/loose soil complete all as specified and directed Engr-in-charge.

Disconnecting electrically incomming and outgoing LT UG cable of LT panel of any size and replace burn/unsv suitable size of aluminium bus bar, Welding work for hinches and doors, fixing the locking arrangement including scraping outdoor/indoor side of LT Panel and one coat of redoxide, two coat of synthetic enamelled seimens gray spray of outdoor/Indoor side and reconnecting LT UG cable with fixing aluminium lugs by using crimping tool, nut, bolt washer etc and all necesary work required for smooth functioning of LT panel complete all as specified and directed by Engr-in-Charge.

S&F in replacement of old existing self reflector type flexi board with PVC frame of size 1.2mx0.8m including diagram of water disribution network at each pump house complete all as specified and directed by Engr-in-Charge.

M&L for repairing of old damaged cement concrete column for lowering and lifting of submersible motor pump on roof of pump house bulding using PCC (1:3:6) type C-2 using 40 mm graded aggregate as in foundation filling & mass concrete fair finish over surfaces along with painting of ISMB with two coat of black synthetic enamel paint complete all as specified & directed by Engr-in-charge.

M&L for demolition of old brick cement work in ground and pavings and repairing the same as directed and fixing of 50x5 mm angle iron U shaped of suitable length upto 5 mtr approx by cutting , welding threading and jointing complete suitable for hanging of Hose Reel Box of fire fighting system with PCC (1:3:6) type C-2 using 40 mm graded aggregate as in foundation filling & mass concrete fair finish over surfaces alongwith two coat of red synthetic enamel paint on angle iron and hose box complete all as specified & directed by Engr-in-charge.

Material and Labour for Mild Steel ERW (Electro Resistance Welded) pipe with flanged ends suitable for Column Pipe of bore dia 150mm,8 mm wall thickness including gasket, bolts and nuts for fixing and taking out of old pipes complete all specified and directed by Engr-in-Charge. [Note: The pipes should be in 3.0 mtr length with both side flanged suitable for column pipe for Bore well]

Attending complaint for rectification of leakage of 50mm bore GI Pipe line including excavation, returning and filling etc including fittings like unions, sockets, bends, elbows, tees, nipples etc as per site requirement and complaint shall be rectified within 24 Hrs from date of complaint failing which recovery shall be charged @ 500 per complaint per day complete all as specified and directed by Engr-in-charge

All as per item No.267 here in above but 25 mm bore complete all as specified and directed

All as per item No.267 here in above but 20 mm bore complete all as specified and directed

All as per item No.267 here in above but 15 mm bore complete all as specified and directed

M&L for applying two coats of cement based paint on all external surface of overhead reservoir of capacity 100000 gallons including coulms and beams of staging up to 21 metre high after scraping/ preparing of Old surfaces and two coats of synthetic enamel paint on Inlet, outlet, overflow and washout CI/ GI/ DI pipes and complete staircase as per existing colour from ground level up to top of the reservoir complete all as specified and directed by Engr-in-charge. [Note: - (i) Before applying cement paint, the surface shall be thoroughly wetted to control surface suction(ii) Not less than 24 hours shall be allowed between two coats and the second or subsequent coat shall not be started until the preceding coat has become sufficiently hard to resist marking by the brush being used]

All as per item No.271 here in above but for overhead reservoir of capacity 50000 gallons complete all as specified and directed by Engr-in-charge.

M&L for applying two coats of synthetic enamel paint on DI fittings and fittings of distribution header including sluice valves of various pump houses after scraping/ preparing of Old surfaces and writing location of particular area to be fed on each distribution line along with arrow mark complete all as specified and directed by Engr-in-charge.

M/S CHANDRIKA PRASAD AND SONS (BID ID -3069052)

MTR GROUP & COMPANY (BID ID -3068162)

Unnati Engineers (BID ID -3068674)