CERTAIN MISCELLANEOUS REPAIRS TO FENCING, IRON GATES, BOUNDARY WALL, HARDSTANDING AND OTHER CONNECTED WORKS AT CERTAIN LOCATIONS AND WALL, FENCING, CULVERTS, HARDSTANDING, PAVER BLOCK, CHEQUERED TILES, KOTA STONE AND OTHER MISC WORKS AT AIR FD AND OT

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) including distance pieces, cleats etc. complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and directed.

Dismantling of Plain or corrugated steel / AC sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

S&F Plain, galvanised, mild steel sheeting thickness 0.63mm, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground

Dismantling of timber scantling as fillets, rails, posts, rafters, purlins, any section & any description complete all as specified and as directed.

S&F in repair Galvanised 2 strand, steel Barbed wire 2.24mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed.

Restraining and resecuring steel barbed wires of any description including making good staplesetc

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire.

Supply only galvanized iron chain link fencing approved size complete all as specified and directed by Engr-in-Charge.

Excavation in hard/dense soil as in post holes each n.exc 0.50cum, getting out, returning, filling, in and ramming earth or broken rubble mixed with earth around, in layers n.exc. 25cm, watering and removing surplus soil all as specified.

M&L for cement concrete in foundations, filling, bed blocks and mass concrete type B-2 (1:2:4) (40mm graded aggregate) complete all as directed.

Providing reinforced cement concrete type B-1 (1:2:4) ( 20 mm graded aggregate) in precast posts, fencing posts, straining or terminal posts, struts etc. for fencing average sectional area n. exc. 100 sqcm with or without chamfered angles and flat, splayed, rounded or mitred tops including necessary form work as directed and fixed.

S&F mild steel angle iron posts and struts in fencing post and iron flats for securing chain link fencing including all necessary drilling bolting etc. and similar work all as specified and directed

S&F mild steel screw bolts machine made with hehagonal or square heads at one end and screwed the other, or screwed both ends each screwed and to be fitted with washers and one hexagonal or squere nuts n. exc 5 cm long and diqa of neck 10mm.

M&L for mild steel round bars 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

S&F mild steel framed work such as framed and hung as gates ornamental and intricate design, including pintle hinges, stops, hand-made sliding bolts, etcgrills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framed work and similar works conforming to Fe-290 Gd E-165 complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel n. exc 10 cm in width or girth and unconnected with other painting and applying two coats of synthetic enamel paint over a coat of red oxide, complete

Dismantling boarding, jallies, fencing of any description fixed in any position

Providing precast cement concrete louvres and jallies, 35mm thick type B0 1:2:4 (12.5mm graded aggregate) set in cement mortar (1:4) (mea-sured solid), including all mouldings but excluding frame

M&L for PCC 75 mm thick type B2 (1:2:4) using 40 mm graded stone aggregate) in plinth protection, joints should be filled with bitumen primer etc, complete all as specified and as directed.

Demolition of brick work built in cement mortar in any position and removing rubbish off the premises within 50m all as directed by the Engineer-in-charge.

M&L for brick ,modular size kiln well burnt sub-class 'B' bricks, exc 6m in mean radius, built in CM (1:4), complete all as specified and directed.

M&L for brick work with modular size kiln well burnt sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water, etc, including removal of rubbish off the premises, removal and depositing serviceable materials where directed and leaving the work clear of any plastering.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required.

M&L for plain cement concrete, type C1, 1:3:6 (Using 20mm graded granite stone aggregate) cast in situ in bed blocks, copings and the like including weathering, solightly rounded or chamfered angles and throating as directed including use and waste of form work.

M&L for Reinforcement cement concrete (nominal mix) type B-1 (1:2:4) (12.50mm graded stone aggregate) as in foundations, footings of columns etc.

M&L for Reinforcement cement concrete (nominal mix) type B-1 (1:2:4) (20mm graded stone aggregate) as in columns, pillars, piers posts and struts etc.

M&L for Reinforcement cement concrete (nominal mix) type B-1 (1:2:4) (20mm graded stone aggregate) as in beams, lintels, slabs, copings etc.

M&L for mild steel TMT bars 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm bore or securing with clips complete all as specified and directed.

Use and waste form work to sides of concrete foudations, footings for flat and rough finished surfaces of concrete

Use and waste form work to sides of columns, pillars posts struts for flat and rough finished surfaces of concrete

Use and waste form work to soffits and sides of beams, lintels etc. for flat and rough finished surfaces of concrete

M&L for preparing new surfaces of walls and applying two coat of cement based paint complete all as specified and as directed. (Note : Rate shall be included for necessary scaffolding and safety measures where required at site)

Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M as directed by the Engineer in Charge.

M &L for Cement concrete type B2, 1:4:8 (using 40 mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and as directed.

M & L for PCC 1: 2 :4 type B-2 (using 20mm graded crushed stone aggregate) as in surface channels and drains including necessary form work complete all as specified and directed.

M&L for coloured Precast Cement concrete heavy duty deisigner tiles of size 400 x 400 x 25mm set jointed and pointed in neat cement slurry in floors with grey cement complete all as specified and directed.

M & L for coloured Rubber Moulded Chequred Cement Concrete tiles 300 x 300 x 30mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15mm thick screed bed in CM 1:6

M&L for sand filling under floors or in foundations below interlocking tiles path including watering and consolidation complete all as specified

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-40 Grade with grey cement and pigment complete all as specified.

M&L for providing Precast cement concrete in type B-1, 1:2:4 (20mm graded aggregate) in Kerbs and edging to road, divider and foothpath etc incl necessary earthwork with plain fair faces, incl chamfered whethereing, throating etc and setting in cement mortar 1:4 complete with joints to match.

M&L for preparation of new concrete surface of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint compete all as spcified and directed.

M&L for 40mm thick PCC type B-1, 1:2:4 (20mm graded aggregate), as in levelling course complete all as specified and as directed.

M&L for preparation of old treatment and painted surface of plastered / decorated surface and applying one coat of Premium Acrylic smooth exterior paint complete all a specified and as directed. (Note : painting will be done by brush / spray / roller of building upto the height G+1) all as per directed by Engr -in-Charge)

Demolition of reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness, (Below or above ground level) separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M as directed by the Engineer in Charge.

Precast cement concrete 1:2:4, type B1 (Using 20mm graded stone aggregate) in landings, bed plates, pintle blocks, anchorage blocks, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 including necessary form work, complete all as specified

S&F Reinforced concrete pipes 200mm bore class NP2, laid and jointed complete with collars

S&F Reinforced concrete pipes 300mm bore class NP2, laid and jointed complete with collars

Demolition of stone slabs of any description or thickness in floors/ walls laid bedded and pointed in any mortar etc. complete removal of debris outside MD land.

M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing ompleteincluding 15mm thick screed bed in CM 1:6

-ditto- but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

ram prashad chotelal batham

sabir and brothers