MISC SPECIAL REPAIR WORKS AT KV NO. 1 AT AF STN ADAMPUR

Amount

B/R WORKS

Earth work in excavation by mechanical means (Hydraulic excavator) in all kind of soil in foundation trenches or drains (not exceeding 1.5 m in width or 10 sq.m on plan), including dressing of sides, removal of bushes including roots coming in alignment of boundary wall if any and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m comlete all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each, complete, all as specified.

Broken bricks hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete, all as specified.

Blank

PCC type E-2 (1:5:10), using 40 mm graded stone aggregates as in filling & mass concrete, sub base, complete all as specified.

40 mm thick damp proof course to horizontal or vertical surfaces including necessary formwork in cement concrete 1:2:4, type B-0, using water proofing compound, complete all as specified. NOTE: Water proofing compound will be measured and paid for separately under respective item of Schedule 'A'.

Cement concrete, type B-1 (1:2:4), using 20 mm graded stone aggregates as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete all as specified.

Reinforced cement concrete, design mix M-25, using 20 mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Reinforced cement concrete, design mix M-25, using 20 mm graded stone aggregates as in beams, cantilevers, bressumers, lintels over 1.5 metre clear span and the like complete all as specified.

Blank

Supply only water proofing compound, ISI marked, complete all as specified.

Brick work using bricks as specified in PS-II clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified.

Brick work using old size bricks (EXCEPT BRICKS) straight or curved on plan exceeding 6.00 metre mean radius, built in cement mortar (1:6), complete all as specified. NOTE: Old bricks obtained after dismantling of brick work will be reused after cleaning etc under this item.

Brick work using old size bricks, straight or curved on plan to any radius in half brick thick wall, built in cement mortar (1:4), complete all as specified.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends, or edges of landings etc. and cutting chases for concealed water tubing, concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, in brick walls, complete all as specified.

Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surfaces of concrete, complete all as specified.

Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with rough finished surfaces of concrete, complete all as specified.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished surfaces of concrete, complete all as specified.

Factory made, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, 35 mm thick, ISI marked, complete all as specified.

Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm plain PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening, complete all as specified.

Factory made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2 mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face and 2 mm prelam PVC sheet on back face complete all as shown on drawing and as specified.

Factory made PVC cup board shutter 25 mm thick consisting of frame made out of MS tube 15 x 15 mm for stiles & rails (Size 100 mm x 25 mm), MS frame shall be covered with 5 mm thick heat moulded PVC sheet 'C' channel having 5 mm thick PVC sheet strip of 15 mm width stuck inside with slvent cement forming stiles & rails. Panelling of plain colour 5 mm thick PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, all as shown on diiagram at Serial Page 171 of MES Schedule Part-I (2009), complete.

Stainless steel 100mm long butt hinges with stainless steel screws, complete all as specified. MAKE :PRAYAG CAT NO. HG-2412 or equivalent make mentioned in Appndix 'B'

Stainless steel, barrel tower bolt, 200 mm long, with stainless steel screws, complete all as specified. MAKE :PRAYAG CAT NO. TBS-2200 or equivalent make mentioned in Appndix 'B'

Stailess steel, handle, 150 mm long, curve shapewith stainless steel screws, complete all as specified. MAKE :PRAYAG CAT NO. DHC-2150 or equivalent make mentioned in Appndix 'B'

Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tacks or galvanized wire staples, all as specified.

Door closer hydraulically regulated, aluminium die cast body, designation No. 3 universal type, suitable for door shutters up to 851 to 1000 mm in width and of weight between 61 to 80 kg, ISI marked, IN REPAIR complete all as specified.

Mild steel works in hand rails, half round or other stock section or core for wooden handrail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) in-cluding all necessary drilling, bolting or riveting, etc., confirming to Fe-290-Gde E-165, complete all as specified.

Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified.

Blank

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Mild steel TMT bars 8 mm and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and binders complete all as specified.

Factory made pressed steel frames, conforming to IS, having profile 125 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., complete, as specified, supplied and fixed with one shop coat of zinc chromate primer, duly filling with PCC (1:3:6) type C-0, complete all as specified.

Factory made steel windows with side hung shutter (using profile section as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable), each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded, including one shop oat of zink chromate primer complete.

Factory made steel ventilators with top hung shutter ( using profile section as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable), each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded, including one shop oat of zink chromate primer complete.

Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed, (each line wire to be measured) complete all as specified.

600 x 600 mm size 4 mm thick high pressure steam cured pre polished (HPSC) self embosed textured designer E board classic to be fixed on GI powder coated grid section of size 605 x 605 mm with main runner 38 x 24 x 0.9 mm cross Tee 28.6 x 24 x0.9 mm and wall angle 19x 19 x 0.9 mm duly suspended with 6 mm dia GI bar hangers 1200 mm c/c both ways fixed with steel dash fasteners or from purlins from the roof wih alignment clip including provision for light fixtures of any size complete.

50 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified.

Granite jet black shade, 15-18 mm thick, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), as in wall cladding or over cooking platform, window cill and simialr work etc complete all as specified.

Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified.

First quality, glazed ceramic, straight cut/joint free, 6-7 mm thick colored digital tiles, area of each tile exceeding 0.17 sq.m but not exceeding 0.19 Sq.m, on vertical surfaces such as dado etc over & including 10 mm thick cement mortar (1:4) screed set in 3-6 mm thick tile adhesive with notched trowel as per manufacturers instructions and joints shall be sealed with polymer based grout of matching shade of tiles, complete, all as specified.

First quality, non-skid ceramic, straight cut/joint free, 7-8 mm thick colored tiles, area of each tile exceeding 0.11 sq.m but not exceeding 0.18 Sq.m, in floors etc. over & including 15 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry & pointed with grout of matching shade, complete, all as specified.

First quality, Vitrified ceramic (Dark shade) tiles 9-10 mm thick, of size 600mm x 600 mm, in floors etc. over & including 15 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry & pointed with grout of matching shade of tiles, complete, all as specified.

First quality, Vitrified ceramic (Dark shade) tiles 9-10 mm thick, of size 600mm x 600 mm, (cut to required height) in skirting etc. over & including 10 mm thick cement mortar (1:4) screed, set and jointed with grey cement and pointed in grout of matching shade of tiles, complete, all as specified.

Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar (1:6), complete all as specified.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar (1:4), complete all as specified.

Rendering 15 mm thick (Average thickness) rendering on RCC roof surface, when concrete is green, finished even and fair in cement mortar (1:4), using water proofing compound as per recommended ratio, after brushing cement slurry @ 1.20 kg/Sq. m, complete all as specified. NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ.

Washed stone grit plaster on exterior walls in two layers, under layer 10 mm thick cement plaster 1:4 furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per sq.m, top layer 12 mm thick cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping of different approved shades 6-8 mm nominal size) in panels not exceeding 0.36 Sq.m with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete all as specified.

Plain Sheet glass 4 mm thick, ordinary quality in squares not exceeding 0.5 Square metre in each pane, including hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frame including punching or drilling out old glazing pins/spring clips, complete all as specified.

Two coats of cement base paint on wall surfaces including preparation of surfaces complete all as specified.

Prepration of plastered ceiling surfaces complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer.

Prepration of plastered wall surfaces complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer.

Two coats of synthetic enamel paint over & including a coat of pink primer over new wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

Two coats of synthetic enamel paint over steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified.

Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified.

Steel tubes ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, including taking up or down existing unserviceable steel tubing and connections, complete all as specified of size: -

15 mm bore

20 mm bore

Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIR, complete all as specified.

Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIR, complete all as specified.

Sink mixer, swan neck type, swing spout, cast copper alloy, chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIR, complete. MAKE: PRAYAG Cat No. 9260 or equivalent make mentioned in Appndix 'B'.

Stainless steel round slotted grating with frame, 125 mm size and fixed in position with cement joints, complete all as specified.

Cast copper alloy, chromium plated towel rail, 600mm size & dia of tube not less than 20 mm, complete. MAKE: PRAYAG Cat No. BA-10S or equivalent make mentioned in Appndix 'B'.

Soap dispenser holder with soap container, complete. MAKE: PRAYAG Cat No. BA-83 or equivalent make mentioned in Appndix 'B'.

Corner glass shelf 300 mm (with ABS brackets) complete. MAKE: PRAYAG Cat No. BEA-46 or equivalent make mentioned in Appndix 'B'.

One piece Vitreous China wash down water closet pan (pedestal pattern) of size 690 x 375 x 785 mm with integrated cistern, seat cover and twin flush fittings, white, including fixing acessories, IN REPAIR, complete. MAKE: PRAYAG modal URBONA or equivalent make mentioned in Appndix 'B'.

Toilet paper holder, cast copper alloy, chromium plated, glossy finish and fixed in position, complete. MAKE: PRAYAG Cat No. BA-18 or equivalent make mentioned in Appndix 'B'.

Health faucet CP brass body with wall hook and 1 metre SS tube complete.

Vitreous China counter type wash basin, white, size 500 x 400 x 130 mm, with & including cast copper alloy, half or full threaded chromium plated waste coupling suitable for & including 32 mm size PVC waste/discharge pipe, IN REPAIR, complete.

Fancy type 5-6 mm thick looking glass fixed over not less than 6 mm thick PVC ply and approved shade PVC beading not less than 15 mm wide alround with and including all fixing acessories, includiing taking down existing looking glasses (600 x 450 mm size) complete.

PVC connections 15 mm size of length 450 mm with PTMT nuts, IN REPAIR, complete all as specified.

Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe and waste coupling, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified.

uPVC pipes, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors as SWR pipes, IN REPAIR, complete all as specified of size: -

75 mm external dia pipe

110 mm external dia pipe

uPVC/PVC bend any radius, complete all as specified. suitable for uPVC soil waste discharge pipes, IN REPAIR, of size: -

75 mm external dia pipe

110 mm external dia pipe

PVC (SWR) 'S' trap 110 mm size , setting and jointing with solvent cement for 110 mm external dia, type-B pipes, IN REPAIR, complete all as specified.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement for 110 mm external dia, type-B pipes, IN REPAIR, complete all as specified.

Concrete bed to drain pipes 110 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested; in Cement concrete 1:3:6 type C-2, complete all as specified.

Cutting into existing manholes for connecting new drains of 100-110 mm bore pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1, smooth finished, reforming benching as required, complete all as specified.

E/M WORKS

Point wiring with multi-stranded copper conductor, single core, FRLSH PVC insulated and unsheathed cable, including FRLSH PVC insulated unsheathed multi-stranded copper conductor single core cable as earth continuity conductor to common earth and connected to earth dolly, with & including GI terminal box not less than 1.6mm thick with base frame and cover plate of required module (suitable for modular switch/sockets) comprising the following: -

One light point controlled by one switch or one fan point controlled by one switch & fan regulator etc. with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit not less than 20mm dia all as specified.

One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified.

One Socket outlet three pin, 6 Amp, independent, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit not less than 20mm dia all as specified.

One Socket outlet three pin, 6 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non metallic PVC heavy duty concealed conduit not less than 20mm dia all as specified.

NOTE FOR SERIAL ITEM 80,80.1-80.4: (a) Switch(es), socket(s) shall be measured & paid for separately under respective item of Schedule 'A'. (b) Terminal boxes shall be fixed flush to walls with cement & sand mortar (1:4) complete on the location as approved by EIC. (b) In ceiling portion PVC Conduit shall be fixed/laid on surface.

Switch modular type single pole, one way, 6 Amp, one module, complete all as specified.

Bell push switch modular type single pole one way, 6 Amp, one module, complete all as specified.

Switch modular type single pole, one way, 16 Amp, one module, complete all as specified.

Socket outlet modular type, multipurpose, 2/3 pin, 6 Amp, two module, complete all as specified.

Socket outlet modular type 6/16 Amp, two module, complete all as specified.

Ceiling rose, surface bakelite, 65 x 50mm, three terminals complete, all as specified.

Lamp (angle) holder, insulated body, complete, all as specified.

Electric bell, AC 230 volt, single pole, Ding Dong type, complete all as specified.

Sub main wiring (with approved colour coding as per IS) with single core FRLSH PVC insulated flexible stranded copper conductor 1.1 KV grade (main cable: number of runs as indicated below along with single core FRLSH PVC insulated flexible stranded copper conductor 1.1 KV grade for earthing in conduits, complete all as specified of sectional area: -

2 runs of 6 Sq. mm main cable + 1 run of 6 sq. mm earth cable

NOTES: (i) Conduit & conduit accessories shall be measured & paid for separately under respective item of BoQ. (ii) For payment purposes, two runs of main cable as mentioned above and one run of earth cable shall be considered together as "1 RUNNING METRE"

20 mm dia, rigid non metallic PVC concealed conduit heavy duty, 'ISI marked' , inclusive of all fittings (such as junction boxes, bends, elbows, tees, reducers, bell mouth tube ends) and all fixing accessories such as couplers lock nuts, saddles, pipe hooks etc for wiring, complete all as specified.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 240 volt, breaking capacity not less than 10 kA, complete all as specified.

Sheet metal enclosure for DB for fixing MCB’s, isolators etc., having IP-43 protection, suitable for surface and flush mounting, for SPN, 12 way with 200 Amp rated bus bar, 230 V, IN REPAIR, complete all as specified.

MCB, 6-32 Amp, 240 volt, single pole, breaking capacity not less than 10 kA, 'C' curve/series, complete all as specified.

MCB, 6-32 Amp, 240 volt, single pole & neutral, breaking capacity not less than 10 kA, 'C' curve/series, complete all as specified.

Blanking plate of plastic to cover unused space in DB's complete all as specified.

LED wall mounted batten light luminaire 20 watt comprises of extruded channe in thermally conductive materil, high translucent serrated milky white diffuser to get glare free and smooth light distribution having efficacy not less than 90 lumen/watt complete. MAKE: Crompton Cat Part No. LDL-20-CDL or equivalent in makes mentioned in Appendix 'B' here-in-after.

Environment friendly, energy saving surface mounted, decorative oval bulk head edge lit 10 watt bulk head LED luminaire, lumen output should not be less than 90 lumens per watt complete. MAKE: Havells Cat Part No. LHEOAOP7UZ6W010 or equivalent in makes mentioned in Appendix 'B' here-in-after.

Exhaust fan 380 mm sweep, heavy duty with louvers and connecting up complete from ceiling rose or connector to fan, complete all as specified.

DISMANLING/DEMOLITION WORKS

Taking down chowkhats or frame not exceeding 1.5 Sq. m each with shutter(s) (without taking off shutters from the frame), complete all as specified.

Taking down chowkhats or frame exceeding 1.5 Sq. m but not exceeding 4 Sq. m each with shutter(s) (without taking off shutters from the frame), complete all as specified.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete, all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding on brick walls including racking out joints hacking for key and scrubbing removing rubbish from premises, complete all as specified.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified.

Demolition of RCC of any description and in any position not otherwise specifically provided for complete all as specified.

Dismantling of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified.

Dismantling wrought iron or mild steel work of any description, complete all as specified.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground, embedded with concrete etc. complete all as specified.

Taking down existing barbed wire fencing of any type an description from posts of ay description, complete all as specified.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete with batten, casing caping of MS or and PVC conduit on surface or concealed, including switches, ceiling roses, pendants, regulators, sockets, mild steel terminal boxes etc., removing materials complete all as specified.

Disconnecting and taking down light fitting of any description, complete all as specified.

M/s Sahib and Company

PRATHAM TRADERS

MALHOTRA AND ASSOCIATES