Keeladi Museum

Amount

Labour charges for drilling / boring towards providing under reamed cast-in-situ pile of 450mm dia nominal dia to a depth of 0 to 8mtr depth from the ground level and till the as per ur soil report/ excavated level to the tip of pile with necessary M20 concrete and steel grill including under relevant item with single bulb, bore by Bentonite Slurry, where required, lowering the concrete by “Trimie” method all as per IS-2911/Part-II 1973. etc., The rate is inclusive of all conveyance charges, machinery charges etc., The cost of M20 concrete and steel reinforcement will be measured and paid seperately etc., complete complying with standard specification and as directed by the departmental officers.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Refilling basement with excavated earth in layers of not more than 15cm thick well rammed, watered and consolidated etc.,all complete complying with standard specification

Supplying and filling in foundation, basement, etc with M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with Gravel in layers of not more than 15cm thick well rammed watered and consolidated etc.,

Providing Pre - construction Anti - termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam, all round the Pile Caps, Catch basins, trenches, pits, tunnels, wall trenches, back fill, plinth filling, junction of wall and floor. External perimeter of building, surrounding of pipes, expansion joints, below U.G. sump and retaining/side walls etc. as per instructions of chemical manufacturer as directed by the Department officer/ Architect. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be Biflex Tc, TC stands for Termiticide Concentrate for Termite Control (Bifenthrin) and the application shall be diluted 1 part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification. Including cost of chemicals labour charges,transport and storing etc complete and as directed by the department officers

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Cement Concrete 1:5:10 (One cement, Five sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/ms and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement

Ground Floor

Providing and laying in position, standardised concrete Mix M-25 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 k9. of 20mm machine crushed stone jelly and with about (3'3 cu'm') 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg' of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and erecting centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) .

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Brick work in Cement Mortar 1:6 using best quality II class table moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Foundation and Basement

Ground Floor

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Providing and Fixing the Wooden Rafter Beams of different sizes for supporting on roof Tiles and sunshade tiles. The rate inclusive of all materials, labour power and conveyance of materials to the work site, loading & unloading etc., and as per drawing and design by the Departmetnal Officers and All the materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter. Solid panel PVC door with frame

Making, supplying and fixing of glazed ventilator with new Teak wood glazed ventilator of size 1.20x0.60m by using Teak wood scanting thickness of size 0.04m frames fixed with 4mm thick pin headed glass including labour for wrought put up and fixing the ventilator in position with necessary furniture fittings including finishing the Ventilator with one coat of primer and finishing neatly etc., complete complying with standard specifications and as directed by the departmental officers.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best quality Heritage pattern Cement tile of bharat tiles brand of size 200 x 200 mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three Crushed Stone Sand (M.Sand)) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The design of the tiles should be got approved by the Architect before use on works)

Flooring with Anti skid Self Designed Colour Ceramic Tiles of size 305 x 305 x 6mm ceramic tiles laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and fixing WPC Jally(Wood plastic composite) of Computer Numeric Controlled (CNC) Laser cutting with a high level of accuracy of desired size and design as specified in the Work site. The jally should be of 100%Water Proof, 100% Termite Proof and UV protection. The rate is inclusive of all labour, Transportation charges to the work site, the hiring charges for the necessary lifting tools and plants. The design of Jally has to be approved by the Executive Engineer before use on work.

Supplying and fixing Eaves board of size 25 cm x 2 cm using teak wood of best quality as per existing style including cost of teakwood , labour wrought and putup, labour charges for fixing in position etc. complete complying with standard specifications

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Dadooing walls with Dadooing with printed design colour glazed tiles of size 300mm x 200mm x 6mm sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing approved best quality aluminium anodised towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing in position 15mm dia brass CP screw down tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supply and fixing in position of best white glazed Jaquar or Equivalent glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position Urinal partition with White Marble slab (Adanga) 18 mm to 20 mm thick of 4'0'' x 2'0''size and above of best quality including dismantling masonry, if necessary and re-doing the same to original condition, etc., complete complying with standard specification. (The Marble slab should be got approved by the Executive Engineer before use on works).

Supplying and fixing position PVC Nahani Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best quality and approved make Indian made star white earthernware Vitreous wash hand basin of size 550 x 400mm (with pedestal ) Jaquar or Equivalent with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white glazed European Water Closet wall mounted of best quality of Jaquar or equivalent with consealed flushing tank and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying, laying and jointing CPVC (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

32mm dia CPVC pipe- BGL

40mm dia CPVC pipe- BGL

25 mm dia CPVC pipe- AGL

Supplying CPVC Specials in water supply arrangements (both in internal and external water supply arrangements including cost of cutting, threading and pasting. Complete complying with standard Specification and as directed by the departmental officers.

40mm dia Elbow

32mm dia Tee

40mm dia Union

32mm dia Union

20mm dia bend

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). Above Ground Level

75mm dia Pipe

110mm dia pipe

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation,sand filling and refilling charges etc. will be measured and paid separately in the cases where the pipe lines are proposed to laid Below Ground Level

75mm dia Pipe

110mm dia pipe

Supplying and fixing approved best quality PVC Water Tank complete complying with standard specifications. (The PVC Water Tank should be got approved by Executive Engineer before use on works).

Supplying and fixing in position best approved of BIS quality 110mm dia PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Supplying and laying TAMIN paver blocks of 60mm thick, the cost include base cushion of 10cm depth transporting charges etc. complete complying with std. specification.

Manufacturing, supplying and fixing in positon of RCC Jally of 5cm thick in cement concrete 1:2:4 using 20mm machine crushed stone jelly (excluding cost of reinforcement steel) including cost of mould, finishing, curing, lifting, fixing in position etc., complete complying with standard specification and as directed by the departmental officers

Supplying, fabricating and fixing inposition Aluminium glazed fixed partition using 63.50x38.10x2mm @1.127 kg/m Alu.section at 900mm C/C in vertical direction and 1300mm @ C/C at horizontal direction with necessary rubber beadings Alu. clips, of size 17.27x17.15x1.40mm@ 0.175 kg/m and using 5.50 mm thick plain glass including cost of all materilas, labours, power consumptions required for fabrications, drilling holes in RCC column, slab, masonry walls wherever necessary with powerdrills to the required extent and make good to the original condition after fixing and also as directed . All the aluminium sections are to be anodised with matt finish under electrically controlled conditions in accordance with IS 1868/1962 for an avereage abiduc film thickness of 15 microns etc. complete.

provision of Cornices with moulding, decorative bands using cement mortar (1:3 Cement Mortar and finishing it with fine mortar using brick masonry set in 1:0.5: 3 Cement mortar, plastered with 1:3 CM finished with 1:2 fine ground CM) including inserting brick pieces, making templates to match the original work etc complete up to 450 mm thick/wide

Supply and fixing Granite stone column, Beam hooks and columns base of heritage type of design and dimensions as per architectural drawing.

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the departmental Officers) including construction of mud pit.

Upto 60 m Depth ending below ground level

From 60m upto 90m depth ending from ground level

Reaming the bore well from 150mm dia pilot bore to 300mm dia bore as directed by the departmental officers upto 60m depth ending from ground level.

Upto 60 m Depth ending below ground level

From 60m upto 90m depth ending from ground level

Supplying and fixing PVC Plain casing pipes of 160mm dia vertical 10Kg/Cm2 in sedimentary depth as directed by the departmental officers etc. Complete..

160 mm dia slotted PVC pipes

160 mm dia slotted PVC pipes

Supplying suitable PVC End cap ( 6kg/sqcm) of best for casing pipe of 6" dia borewell quality with ISI mark, The PVC should got approved by the departmental officers before execution.

Supplying, laying and jointing CPVC (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

40mm dia CPVC pipe- BGL

Supplying & fixing of 2.00 H.P submersible pump

Nylon rope for bore well

Supplying of 3/20 copper wire of best quality etc complete complying with standard specification.

Supplying and fixing wall mounting of Panel board with following accessories

3 phase panel board including labour charges

MODULAR TOILET CUBICLES Supply & Installation of Modular Restroom cubicle system that includes intermediate panel, pilaster & door made of compact laminates of single colour. The heat, bacteria, water, chemical and scratch resistant solid compact laminate to be based on thermosetting resins, homogeneously reinforced with cellulose fibres and to be manufactured as per relevant quality standards. Top surface on both sides to be melamine coated which should be scratch & impact resistant. All intermediate panels, pilaster & doors shall be 12mm thick with edges chamfered. ACCESSORIES & CHANNELS - STAINLESS STEEL(i) Door hinges (ii) Coat hook (iii) Door knob (iv) Lock with occupancy indicator(v) Floor channel (vi) U-channel (vii) Door-stopper channel w/noise deafening tape(viii) Top rail (ix) Shoe box w/clamp & end cap (ix) Screws & Wall plugsIncludes SS Shoe Box below Front Panels, U Channel below Intermediate Dividers

Supplying installation of Incinerator for ladies toilet etc., as ditrected by the departmental officers. The cost includes cost of materials, cost of labour, scoffolding , transportation, conveyance etc., Complete complying with standard Specifications.

Supply, fabrication, erection, alignment and levels as per shop drawing of structural steel work in built up sections comprising of ISMB, ISMC, angle, plates and round bar section etc., Necessary permanent rivets, bolts, washers and nuts, handling, straightening, cutting, drilling holes, welding, sand blasting, shop assembly, transport to erectiopn site, storing, leading to erection site and apply a coat of anti- corrosive colour paint of approved make and colour and two coats of MRF enamel paint prior to erection, complete job in all respect. a) Connection bolts are E250 GR 8.8 (IS 3757) , or equivalent, plate grade is E350 and all structural steel conform to IS 2062 c) Specification for cold formed light gauge structural steel sections conform to IS 811 d) Painting conform to IS 1477 part 1 & 2. The rate is inclusive of design, shop drawing preparartion, submission for approval etc., and also inclusive of any other incidental charges such as using cranes, labour charges for erection, cost of all materials involved and painting two coats over one coat of primer and as directed by the departmental officers.

Supply, fabrication, erection, alignment, and levels as per approved shop drawing of structural steel work in single section for purlins, tie runners with sag rods etc., Necessary permanent rivets, bolts, washers and nuts, handling, straightening, cutting, drilling holes, welding, sand blasting, shop assembly, transport to erectiopn site, storing, leading to erection site and apply a coat of anti- corrosive colour paint of approved make and colour and two coats of MRF enamel paint prior to erection, complete job in all respect. a) Connection bolts are E250 GR 8.8 (IS 3757) , or equivalent, plate grade is E350 and all structural steel conform to IS 2062 c) Specification for cold formed light gauge structural steel sections conform to IS 811 d) Painting conform to IS 1477 part 1 & 2. The rate is inclusive of design, shop drawing preparartion, submission for approval etc., and also inclusive of any other incidental charges such as using cranes, labour charges for erection, cost of all materials involved and painting two coats over one coat of primer and as directed by the departmental officers.

Purlin but with painted cold rolled steel sections Z section MET- Z Purlin 150x2-25*50 (As per Quotation)

Sag rod (As per Quotation)

Supplying and fixing of M.S.Steel special extended sections for truss work using M.S. Angles, Flats with ornamental designs. The rate inclusive of all labour charges, welding charges and conveyance etc.,. Complete complying with standard specifications and as directed by the departmental officers.

upplying and Fixing colour galvanize sheet roof of 0.47 mm thick and steel tubular box section of 100x50x3 mm of 1 meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers

Supplying Of Glass Fibre Reinforced Concrete (G.F.R.C)/(G.R.C.) COLUMN casted with Spray Mix concrete design in approved size, pattern, thickness 20mm. The Elements should be made from ‘53 grade’ White Portland Cement manufactured by ‘JK Cement’/'Birla white'/Penna's RKC.White Quartz fine graded sieve Silica Sand, Alkali Resistant Glass Fiber manufactured by 'NEG Japan, Owen Corning or equivalent, Super Plasticizers manufactured by ‘Karochem’ or equivalent, Polymers manufactured by ‘Nova Polychem’ or equivalent. The Elements casting shall take place with layering methodology using- Direct Power Spray machines. The GRC Elements flexural strength average L.O.P should be above or equivalent to 6 N/mm2 & M.O.R should be aboveor equivalent to 12 N/mm2 for tests done on 28 days cured samples.The fixing of Elements should be done using ‘Screw fixing’ method onto structural support members. (As per Quotation)

Providing, assembling and supplying of clear toughened glass of following thickness which is manufactured by heating at a temperature of approximately 650°C and then rapidly cooling process. The glass should withstand high temperatures upto 250°C and abosrb 65% of UV rays. The glass panels need to be joined with suitable silica sealant and enclosed properly with good quality rubber material to prevent leakage. The rate is inclusive of all labour, Transportation charges to the work site, the hiring charges for the necessary lifting tools and plants. The design of glass has to be approved the Executive Engineer before use on work.

12 mm thick (As per Quotation)

8 mm thick (As per Quotation)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe consealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End (SD-285)

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator)( 6 points / Coil) Higher End (SD-261)

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End (SD-373)

Supply and fixing of single box type 4' 20 W LED fitting with CRCA body complete with TW round blocks on wall or ceiling with 20W LED tube with PVC unsheathed copper leads from terminals to the fitting. (Higher end) (DATA-1)

Supply and fixing of the decorative suspended LED type fitting (like Crompton Epsilon CCP.128.36.57.SL.NWH) (Crompton/ Equivalent) with rod/ chain arrangment PVC insheathered copper leads from terminals to the fitting. (Data- 2)

Supply and fixing of downlight LED fittings (Crompton /Orbit). Beam angle 36 degree (Like CDS-200-30-57-SL-NWH (Crompton/ Equivalent) with arrangement PVC unsheathed copper leads from terminals to the fitting. (DATA - 3)

Supply and fixing of LED flood light fitting made up of pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP66, 3000K protection. (Like LFL-80-CDL/60-HPM profile new) (Crompton/ Equivalent) PVC unsheathed copper leads from terminals to the fitting. (DATA - 4)

Supply and fixing of LED integrated well glass Iuminaire with die cast canopy & ger housing with this IP66, Like CIP-314-70-57-SL-CP-NSG (Crompton / Equivalent) with Rod or chaine arrangement PVC unsheathed copper leads from terminals to the fitting. (DATA - 5)

Supply and fixing of Grace foundation chandlier 9LSE14 black and ceiling suspended with PVC unsheathered leads from terminals to the fitting ( Make: LMFHCHCBTEIK005) Grace chandlier grace fountain chandlier 9LS E14 black / Equivalent with PVC unsheathered copper leds from terminals to fittings. (Data -5A)

Supply and fixing of 450mm wall mount, air circulated type fan with acrodynamiically deisgned semi transparent three blades for noise free operation with in-built speed regulator with necessary accessories with connections complete. (M2639/ Equivalent) (SR)

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb. (SD-83)

SSupply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall. (SD-115)

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan. (SD-120) (Crompton LBT W 10 W Twister make / Equivalent)

Supply and fixing of IP65 Rated LED Bollard with robust design and efficient light distribution on suitable concrete foundation with necessary bolts and nuts with PVC unsheathed copper leads from the terminals the fitting. (DATA- 6)

Supply and fixing of 3 core of 4 Sq.mm copper flexible on wall and ceiling / wall on the existing pipe with suitable colour (DATA-7)

Supply and fixing of like K-lite make KP-5115 Pelican Mini Orna Bishop Lighting Pole,SA, Ht.5000mm and 1 No. KL-6791 Pelican Fort, Dimension : A9:O634x618,A12:O634x676mm, Wattage : 1No 50W LED / Equivalent make on suitable concrete foundation with necessary bolts and nuts and supply and fixing of 1 No of 6A SP MCB (Higher end) 4 way terminal block inside the built in control box with PVC unsheathed copper leads from the terminals the fitting. (DATA 8)

Supply and fixing of K-Lite make KP-8321 Pelican Orna Florian Lighting Pole, DA, Ht.5000mm and KL-6791 Pelican Fort, Dimension : A9:O634x618,A12:O634x676mm, Wattage : 2 Nos 50W LED/ Equivalent make on suitable concrete foundation with necessary bolts and nuts and supply and fixing of 1 No of 6A SP MCB (Higher end) 4 way terminal block inside the built in control box with PVC unsheathed copper leads from the terminals the fitting. (DATA 9)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End (SD-518)

Supply and fixing of 8 way single pole and neutral MCB DB IP 42 protection Metal Door cover distribution board with 1 No 32A DP MCB as incoming and 6 Nos 6Amps to 32Amps SP MCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark. (Higher end) (DATA-10)

Supply and fixing of 8 way vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos. 32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End (SD-581)

Supply and fixing of 8 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 250A 4P MCCB switch as incoming and 7 nos. 63A 3P MCB , 3 nos. 6A to 32A SP MCB as outgoing with suitable cable end box on suitable angle iron frame on wall with earth connection only. Higher End (SD 615)

Supply and laying of 3-1/2x120 sq.mm PVC armoured LTUGcable in atrenchtobe excavate data depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. ( SD-187)

Supply and clarnping of 3-1/2x120 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps. (SD-205)

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection. (SD-169)

Supply and Providing cable end terminitaion of 3-1/2 x 120 sq.mm. PVC LT001 aluminium armoured cable with nessesery aluminium cable sockets by crimping etc.. With electrical connection complete (SD-218)

Supply and laying of 3-1/2x25 sq.mm PVC armoured LTUGcable in atrenchtobe excavate data depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. ( SD-182) for High Mast & Pump Room

Supply and clarnping of 3-1/2x25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps. (SD-200) for High Mast

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection (SD-164)

Supply and providing cable end termination of 3-1/2x25 sq.mm.PVCLTUGaluminiumarmouredcablewithnecessaryaluminium cable sockets by crimping etc with electrical connection complete (SD-213)

Supply and laying of 3-1/2x35 sq.mm PVC armoured LTUGcable in atrenchtobe excavate data depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. ( SD-183)

Supply and fixing of brass cable gland for 3-1/2 x 35sq.mm. PVC armoured LTUG cable with earth connection. (SD-165)

Supply and providing cable end termination of 3-1/2x35 sq.mm.PVCLTUGaluminiumarmouredcablewithnecessaryaluminium cable sockets by crimping etc with electrical connection complete (SD-214)

Supply and clarnping of 3-1/2x35 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps. (SD - 201)

Supply and laying of 3-1/2x50 sq.mm PVC armoured LTUGcable in atrenchtobe excavate data depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. ( SD-184)

Supply and clarnping of 3-1/2x50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps. (SD - 202)

Supply and frxing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection (SD-166)

Supply and providing cable end termination of 3-1/2x50sq.mm.PVCLTUG aluminium armoured cablewith necessary aluminium cable sockets by crimping etc with electrical connection complete (SD-215)

Supply and laying of 2x16 sq.mm PVC armoured LTUGcable in atrenchtobe excavate data depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. ( SD-177)

Supply and clarnping of 2 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps (SD-195)

Supply and fixing of brass cable gland for 2 x 16 sq.mm. PVC armoured LTUG cable with earth connection (SD-161)

Supply and providing cable end termination of 2 x 16 sq.mm.PVCLTUG aluminium armoured cablewith necessary aluminium cable sockets by crimping etc with electrical connection complete (SD-213)

Supply and laying of 2x10sq.mmPVC armouredLTUG cableinatrench to be excavatedata depth of 0.75metre putting 0.15metre layerof sand andcovering the cable completely with bricksands and refilling the earth to make good (SD-176)

Supply and clarnping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps (SD-194)

Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC armoured LTUG cable with earth connection (SD-160)

Supply and providing cable end termination of 2 x 10 sq.mm.PVCLTUG aluminium armoured cablewith necessary aluminium cable sockets by crimping etc with electrical connection complete (SD-213)

Supply and fixing of 32 A DP MCB (Higher end) isolator in suitable Double pole sheet steel enclosure with all electrical connection complete (DATA - 11)

Supplyandfixingof200ATPNsheetsteeldoublebreak switch with HRC fuses and neutral on suitable angle iron frame work with MS cable entry boxes PWD earthing (SD 154)

Supply and fixng of TNEB meter board suitable for 3phase 100A service connection madeupof suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size1-1/2"x1-1/2"x1/4"rigidly fixed on wall covered with hylem sheet of size 2 feet x1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3Nos.100Afuse units(500V),1No.neutral link,copper earth flat of size1"x1/4"with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete. (SD-133)

Supply and fixing of 3 Nos. 3 Phase 200A aerial fuse unit (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps. (Data -12)

Supply and fixing of 100 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with PWD earthing (SD-648)

Supply Erection, Testing, Commissioning & Handing over of 1 No. 40 KVA Diesel Generator set of 0.8PF, Three phase, 415/420Volts, 50c/s, 1500RPM CPCB approved capacity compressing of Developing 156 BHP Water cooled clockwise rotating with 40KVA operating capacity brush less alternator close coupled underneath fuel tank standard safeties, LLOP with stop solenoid battery with lead, Electrical start and Anti vibration mounting and accessories and AMF control panel as detailed below including transporting & unloading charges A. Engine: Water cooled diesel engine suitable for Generator application with a shaft output of 156BHP 1500RPM under NTP condition. The Engine shall Comprise the following standard fitting flexible coupling, fly wheel, air cleaner, fan blower, radiator, water pump, fuel filter and lubricating oil filter etc., B. 12/24 Volt Electronic Starting Equipment: Complete with starter motor, dynamo, standard batteries with cable flexible exhaust piping of 50cms length. C. Engine instrument Panel/ Mounted starting push button/starting key lubricating oil temperature gauge lubricating oil pressure gauge water temperature gauge safety control for low lubricating oil pressure, safety control for high water temperature safety control for over speed, Hour meter(mechanical) and RPM indicator battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continues run at full load.

D.ALTERNATOR: 40KVA/ 32 KW capacity brushless alternator AC 3 Phase 50c/s 415/420V 0.80PF 1500RPM under NTP condition conforming to IS 13364(Part-II)1992 to be means of coupling E Standard Control Panel: The standard control panel (cubical ) should be Vermin proof and dust proof best quality sheet steel of 16 SWG CRCA MS Sheet and floor mounted with suitable hinged glass doors, enamel painted and incorporating the following suitable provision for connection incoming and outgoing leads have been made on the control panel. 1. UNDER/ OVER LIMIT i. High coolant Temperature ii. Low lube oil pressure iii. Over speed iv. Start fail v. Emergency stop vi. Over load 2. FAULT INDICATIONS i. Lop-Low lub iol pressure ii. HWT-High water temperature iii. OL-Over load iv. E-STOP-Emergency stop 3. STATUS LED INDICATIONS i. START FAIL-Start fail ii. AUTO-Auto mode iii. MAN-Manual mode iv. MAINS-Mains Available v. DG-Genset ON

4. OPERATING KEYS ON AMF CONTROLLER i. START-Starts the gen set in Manual Mode ii. E-STOP-Stops the gen set in Manual mode 5. PARAMETER SETTING KEYS i. DIP switches The panel should be completed with bus bars internal connections and with necessary fuses, cables and other accessories and with tapings for the incoming supply to the load. (F) FUEL TANK: Fuel tank of 80 litre capacity and with inlet and outlet connections level indicator with scale etc., BASE FRAME: The base frame should be fabricated MS channel frame of rigidly welded construction for mounting the generator set. The engine and alternator should be coupled by suitable designed diapharm type flexible coupling with proper alignment. The supply of generator set including loading, unloading and transportation charges. (G) ACOUSTIC ENCLOSURE The Acoustic enclosure self standing weather proof KG-CPCB typed Acoustic canopy KG 100WS floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather conditions. Erection of Acoustic enclosure suitable 40KVA Diesel Generator complete with all accessories as above and suitable supports etc., 1.Supply of manuals for operation & Maintenance of DG set with Warranty card etc., (SR) (M-2346) (H)Erection and testing and Commissioning of the above Genset:

Providing suitable concrete foundation with cement concrete 1:2:4 with sand cushion all around the foundation erection of 40 KVA Generator set over the existing foundation and erection of generator set with proper alignment over the existing foundation.

Providing fuel oil to run the set for 8 hours on load, testing and commissioning using water rheostat or suitable loading elements.

Preparation of site plan physical layout, electrical line schematic Diagram getting drawing approval from CEIG including preparation of completion report rectification report etc., arranging CEIG inspection and obtaining CEIG safety certificate, payment of CEIG inspection fees including safty tools & accessories.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 76)

Supply and run of 1 No. 8 SWG Copper wire in suitable PVC rigid pipe on wall / Floor/ Ground for earth connection. ( SD 371 )

Earthing as per the ISI specification with an earth electrode of 2.10 metre class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry. (SD - 211)

Design, supply, erection, testing and handing over of High Mast structure Bajaj/Philips make or equivalent with required number of continuously tapered hot dip galvanized steel polygonal sides sections with telescopic strip joints to a total height of 20 meters capable of sustaining the maximum wind pressure at the erection site with single flange base plate secured welded in the bottom of the base mast section with vertically movable hot dip galvanized lantern carriage and accessories such as electrical junction box brackets for providing 6 Nos. of flood light luminaries with control gear box complete head frame assembley, Pulley drive, stainless steel wire rope single/double drum self lubricating winch arrangement suitable for raising and lowering the luminaries carriage ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and anchor plates and templates including supply and fixing the following accessories in the Mast (a) Design and casting of suitable foundation with 1.2.4 mix RCC concrete with 30 cm projection above the ground level with 1 meter width x 1 meter length and 2 meters depth with necessary galvanized foundation bolts nuts and washers and dump plate enclosing the bolts for the High Mast considering the safe soil bearing capacity at site-1 set (b) High powered power tool complete with hand held control panel and motor with push button type remote control switch suitable for 3 phase 415 V 50 Hz for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch -1 set

(c) Feeder pillar box comprising 0.90m x 0.45m x 1.20m floor Alu frame with 63A TPN main switch 1 No, 63A fuse unit 3 Nos, 63A power contactor with automatic timer arrangements & reversing starter for 3 phase motor 1 set. (d) Neon aviation obstruction light (Bajaj BJAOL (2) / equivalent -1 No (e) 2 Nos of special Gi earth electrodes with copper plate 300 x 300 x 3mm and copper flat (1" x 4") interconnection as per ISS complete with earth connection 1 set. (f) Hot dip galvanized lightening arrestor 1 No (g) 200W LED Sports Luminaire IP66, IK08, 5700K with system efficacy at least 100 Lumens / watt as per standard spefication 6 Nos.

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD 448).

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100v grade in suitable PVC rigid pipe on wall and ceiling with contiuous earth wire conection of 4 sq.mm copper wire with painting of suitable color(SD 56)

M/s. LUCKY ASSOCIATES (BID ID -1184176)

KARTHIKEYAN ELECTRICALS (BID ID -1184424)