REPAIR/MAINT OF DG SETS OF VARIOUS CAPACITIES, AMF PANELS AND OTHER ALLIED WORKS AT PUMP HOUSES OF WATER SUPPLY SYSTEM IN THE AREA OF AGE E/M EXT (WS) UNDER GE E/M LUCKNOW.

Amount

Daily Maintenance of AMF Panels of any make and model of D.G.Sets at various locations in Lucknow Cantt area by depolying one trademan including cleaning overhauling and repairs to defective AMF Panels after renewal of defective spares / components of any approved make as per existing or its equivalent complete all as specified & directed. [Note :(i) Each AMF Panel shall be cleaned /maintained daily under supervision of EIC (ii) Fixing of defective spares / Components are deemed to be included in the unit rate but cost of spares / components will be paid under respective items here-in-after (iii) Daily maintenance register shall be maintained for each pump house and shall be signed by representative of contractor and the Engineer in-Charge after doing necessary maintenance)

Taking down and dismantling the spares/ components from engine assy of capacity from 30 KVA to 82.5 KVA Diesel Engine segregating serviceable and semi serviceable and decarbonisation, cleaning of interior& exterior all parts by disconnecting the out going connection from diesel engine from the panel board & re-assebling the same after repair/ replacement of defective spares as directed by E-in-C. (Spares/components shall be measured & paid separately under relevent items)

Spares for DG Set replacement Cap 30 KVA to 50 KVA complete all as specified and directed. (a) Fuel filter ( Primary & Secondary)

b) Oil Filter

c) Air Cleaner

d) By pass filter

e) Super bypass filter

f) Hose pipe set for 30 KVA to 50 KVA DG set

g) Fan belt suitable for 30 KVA to 50 KVA Kirloskar/ Cummins

h) Banjo bolt off sizes

j) Screen filter

k) Fuel Injector pipe for 30 KVA to 50 KVA

l) Injector nozzles for 30 KVA to 50 KVA

m) Injector plunger and plunger spring for 30 KVA to 50 KVA

n) Piston with gugen pin & bush for 30 KVA to 50 KVA

o) Inlet and Exhaust valve, 30 KVA to 50 KVA

p) Tappet bush with packing 30 KVA to 50 KVA

q) Valve guide and spring, 30 KVA to 50 KVA

r) Piston rings

s) Alternator booster panel with AVR system and control unit with all asseceries for 30 KVA to 50 KVA alternator

Spares for DG Set replacement Cap above 50 KVA to 82.5 KVA complete all as specified and directed. (a) Fuel filter ( Primary & Secondary)

b) Oil Filter

c) Air Cleaner

d) By pass filter

e) Super bypass filter

f) Hose pipe set for Kirloskar above 50 KVA to 82.5

g) Fan belt suitable for above 50 KVA to 82.5 Kirloskar/ Cummins

h) Banjo bolt off sizes

j) Screen filter

k) Fuel Injector pipe for above 50 KVA to 82.5 KVA

l) Injector nozzles for above 50 KVA to 82.5 KVA

m) Injector plunger and plunger spring for above 50 KVA to 82.5 KVA

n) Piston with gugen pin & bush for above 50 KVA to 82.5 KVA

o) Inlet and Exhaust valve, above 50 KVA to 82.5 KVA

p) Tappet bush with packing above 50 KVA to 82.5 KVA

q) Valve guide and spring, above 50 KVA to 82.5 KVA

r) Piston rings

s) Alternator booster panel with AVR system and control unit with all asseceries for above 50 KVA to 82.5 KVA alternator

M&L for Taking out FIP from DG set transporting to service center/contractor workshop for over hauling/calibration and refixing on DG Set after replacement of worn out following parts such as screen filter, delivery valves, plunger, O-ring spring rotor assembly injector element etc. complete all as specified and directed. (a) 30 KVA to 50 KVA

(b) Above 50 KVA upto 82.5 KVA

Taking out of turbo charger from DG Set transportation to work shop for repairing and replacement of turbo charger kit & refixing to DG Set and testing complete all as directed by Engineer-in-charge for following capacity :-(a) 30 KVA TO 50 KVA

(b) Above 50 KVA upto 82.5 KVA

S&F in replacement alternator (Dynamo) charger suitable for 12 Volt Battery with all accessories i.e. fabrication of mounting brackets nut bolt etc suitable for DG set of capacity 30 KVA to 82.5 KVA including testing complete all as specified and directed . Make : TVS / LUCAS or equivalent Make for Kirloskar/Cummins .

M&L for supply & replacement lead acid battery 12 volt 150 AH 25 plate including initial charging at various DG sets complete all as specified and directed Make : Exide / Amron

M&L for supply & replacement lead acid battery 12 volt 100 AH 25 plate including initial charging at various DG sets complete all as specified and directed Make : Exide / Amron

M&L for draining out old used lube oil from engine sump, cleaning of sump and supply & filling new lubricating oil SAE grade (15 w 30) multiviscoscity complete all as specified and directed Make : Castrol / CRB / Servo / BP

M&L for draining out old used lub oil from engine sump, cleaning of sump and supply & filling new lubricating oil SAE grade (20 w 40) multiviscoscity complete all as specified and directed Make : Castrol / CRB / Servo / BP

Supply and top up coolant/replacement of coolant by new coolant suitable for ambient temp from 15 to 40 degree centigrade complete all as specified and directed Make : TVS

Supply & pouring distilled water superior grade all as approved complete all as specified and directed

S&F turbo charger with all accessories suitable for 30 KVA TO 50 KVA DG set Make-kirloskar/ cummins or others complete all as specified and directed.

All as per item NO. 50 but 50KVA upto 82.5 KVA

M&L for dismantling and transporting to contractor's work shop of alternator by opening of nut bolts of base plate and coupling opening of front and rear cover removing of fan and removing of armature, rewinding of alternator by super enameled insulated copper wire as per existing gauge, insulating materials, varnishing, drying in hot oven up to desired temperature assembling and testing on connected load complete all as specified and directed by Engineer in charge Note : (Cost of transportation is deemed to be included in quoted rates) (a) Capacity 30 KVA to 50 KVA.

All as per item NO. 52 but 50 KVA TO 82.5 KVA

Material & labour for preparation of old painted surfaces by removing of dust and dirt by caustic soda or any other means, painting of DG set CAP.30 KVA to 82.5KVA of various capacity complete alternator & engine parts as per colour code by spray painting applied two coat of synthetic enamel paint over existing painted surface and marking of SM/MES No on the sets as per approved colour complete all as specified and directed directed .

M&L for dismantling of UNSV and Supply & replacement with new self starter 12 volt Make : Lucas/Autolac suitable for 30 KVA To 50 KVA DG Set

M&L for taking out of burnt out AVR system of DG set by opening of connection chamber of alternator dismantling all existing electric/electronic connection replacement of AVR set reconnection checking of all circuit, testing the same up to the satisfaction of Engr in Charge cap 30 KVA To 82.5KVA

M&L for taking down unserviceable self starter 12 volt from DG Set transporting to contractor workshop dismantling pinion etc , rewinding of armature and field coil by suitable size of insulated copper wire, to achieve its original performance, varnishing, replacement of pinion, pinion spring, carbon brush etc reassembling the same, testing and refitted with DG Set and testing complete all as specified and directed.

Supply and fixing in replacement of solenoids switch for auto on off manual mode in the engine operation including wiring complete all as specified and directed.

M&L for dismantling of water pump assembly from the the DG sets and supply and fixed new water pump assembly for the DG sets of capacity 50/60/62.5/ 63/82.5 kVA including testing complete all as specified.

Dismantling the water body pump assembly complete from the DG set of capacity 30 KVA to 82.5 KVA at site and transporting to work shop & testing and carrying out the following and brought back at site and fixing the same. (a) Over hauling of water body pump complete - 01 Job, (b) Supply and fix water body kit complete- 01 Set, (c) water body bearing - 02 Nos, (d) water body Hose- 01 Set,

Supply & fix battery terminal heavy duty made out of brass suitable for 12 volts lead acid battery all as specified.

M&L for replecement of horness cable control wiring and testing complete all as specified and directed.

S&F off load change over switch cap 100 Amps 4 pole 415 Volts by addition/alteration in existing wall complete all as specified and directed .

S&F off load change over switch cap 200 Amps 4 pole 415 Volts by addition/alteration in existing wall complete all as specified and directed .

Supply & fix in repairs electronic control timer type ET-100 of suitable capacity as required at site. Make:- L&T/ABB/ Legrand/ AE/Secure.

Supply & fix in reapirs engine starter relay of suitable capacity as required at site. Make:- L&T/ABB/ Legrand/ AE/Secure.

Supply & fix outdoor type fountain light waterproof and RGB colour with 6 bulb, 18 watt LED, 12 volt, IP68 with fitting accessories all as specified and directed.

Supply & fix in repairs under voltage relay (Make:- PIC / EC / Wader.)

Supply & fix in repair four Pole Power Contractor -Type MCX-22, 100 Amps, 415V, 50 Hz Make-L&T

Supply & fix in repair three Pole Power Contractor -Type MNX-185, 140 Amps, 415V, 50 Hz, Make-L&T

Supply & fix in repair three Pole Power Contractor -Type, MNX-110, 120 Amps, 415V, 50 Hz Make-L&T

Supply & fix in repair three Pole Power Contractor -Type MNX-140, 160 Amps, 415V, 50 Hz, Make-L&T

Supply & fix in repair four Pole Power Contractor -Type ML-06 100 Amps, 415V, 50 Hz Make-L&T

Supply & fix in repair Single Phase Preventor Relay + Timer 415 Volt Make L& T

S&F distribution box epoxy powder coated, SPN 8 way, 240 V, with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door as in replacment ,complete all as specified and directed.

S&F distribution box epoxy powder coated, SPN 4 way, 240 V, with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door as in replacment ,complete all as specified and directed .

Supply & fix in repair MCB TPN capacity 32 Amps, 415V, 50 c/s 16 KA, complete all as specified and directed .

Supply & fix in repair MCB SPN capacity 32 amp, 'C' series , complete all as specified and directed .

MCB SP 6 to 32 Amps, 240 Volts of 'B' series to be housed in DBs and suitable size cable lugs to be fixed with MCBs as in replacment, complete all as specified and directed .

M & L Point wiring for one light/fan point controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC casing capping alongwith accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly and make wall surface as existing same colour including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately)and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing ,complete all as specified and as directed .

All as per Sl item No 80 here-in-above but for one socket outlet point 5 amps on independent board controlled by one, one way switch.

All as per Sl item No 80 here-in-above but for one socket outlet point on the same baord with other switches.

M & L Point wiring for 15 amps socket point controlled by one, one way switch using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated FRLS unsheathed cables in and including PVC concealed conduit and conduit fittings including pressed steel terminal switch boxes and 3 mm thick plate for fixing of switches/sockets and fitted with Chromium plated brass screws & washers and1.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated unsheathed earth wire and connected to earth dolly including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately)and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing ,complete all as specified and as directed.

S & F Switch piano flush type of sigle pole ,5/6 Amps, one way ,complete all as specified and as directed .

S&F Switch piano flush type of single pole, 15 Amps, one way ,complete all as specified and as directed .

S&F Socket out let 2 in 1 socket 3 pin 5 Amps, flush type controlled by one switch , complete all as specified and directed ..

S&F Socket out let 2 in 1 socket 3 pin 5 & 15 Amps, flush type controlled by one switch , complete all as specified and directed ..

Ceiling rose, Pilot 3 Plate ceiling rose 6A ,complete all as specified and as directed .

S&F Lamp Holder PVC/ polycarbonate type with back plate suitable for batten fittings complete all as specified and directed ..

S&F LED bulb 14 watt all as specified and directed by Engr-in-Charge, Make : Bajaj/Wipro/CG/Philips

Flourescent LED tube light fitting Surface mounting , 1X36 Watt ,energy efficient,ceiling /wall mounting box type fitting complete , with decorative serrated acrylic cover diffused illumination elegantly designed , spring loaded, rotary type lamp holder, connector block etc. and all accessories with 1 No 40/36 watt tube rod including provn of two core flexible copper cable of size 1.5 Sqmm from ceiling rose/connector in and ilcuding taking out old unservicable light , complete all as specified and directed .

Supply & Fixing LED street/bldg light fitting luminaire 70 Watt IP65, 230 volts, new generation energy saving & enviormental friendly long life versatile pressure die cast aluminium roadway luminarie with high power LEDs as light source and electronic driver alongwith suitable bracket required as per site for fixing the light complete all as specified & directed .

M&L for earthing complete for electrical equipments with galvanized steel earth plate electrode 60cmx60cmx6mm buried directly in ground vertically to depth not less than 2.25 mtr below ground level with top edge earth plate at a depth not less than 1.5 mtr below ground level, connected to earth lead of GI strip of size 32x6mm by means of nuts, bolts, check nuts & washers made of galvanized iron or steel and connected to main switch board or main control board as directed charcoal or coke and salt in alternate layers, necessary excavation and earth work in hard/dense soilcomplete all other accessories as shown on electrical plate No 3 of MES SSR Part I including 40mm bore light grade GI pipe 1.8 mtr length with top end covered with plug or cap for watering and 30x30x30cm size PCC 1:3:6 block around watering pipe, excluding 20mm dia watering pipe, PCC, watering pit, funnel, pit cover complete all as specified and directed.

Supply and fixed in repairs DOL starter for chloronome plant fully automatic complete with suitable size cable for connection between starter to auto transformer suitable for ranging from 1HP to 2 HP, 3 Phase, 415 V electric motor including necessary connection and fixed complete all as specified and directed.

NEXT POWER ENTERPRISES

M/S Nav Jyoti Enterprises

Mangalam Trades

M/S S.B. Singh and Sons