Renovation of Conference Hall of Horticulture Complex 2nd Floor Talab Tillo Jammu

Amount

Labour required to be engaged for dismentling old windows,door,floor,conference table including stacking of serviceable material and disposal of unserviceable/rubbish material to ground floor and further to disposable site

Half brick masonary with Bricks of Class designated 75 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) Including all leads, lift and carriage complete.

Extra for half Brick masonary in superstructure above plinth level upto floor V level. Including all leads, lift and carriage complete.

15 mm Cement sand plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 4 fine sand) Including all leads, lift and carriage complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Including all leads, size of tile 80 x 80 cm lift and carriage complete. Including all leads, lift and carriage complete.

Providing and applying white cement based putty on av. thickness 2 mm, of approved brand and manufature, over the plaster wall surface to prepare the surface even and smooth complete. Including all leads, lift and carriage complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primmer. Including all leads, lift and carriage complete.

Providing and fixing aluminum work (10 Guage) for doors, windows, ventilators partitions tubular sections and otherection including 12 mm thick prelaminated particle board on side and balancing on other side, aluminum doors, windows, shutters abd with C. P Brass steel screws all complete job including fittings as directed by engineer in charge (Fixingas well as moveable for payment only area will be measured and nothing extra on account of glass, fixture, gasket paid). Including all leads, lift and carriage complete.Including all leads, lift and carriage complete. (Jindal Make)

Providing and fixing soft Fibre Acoustical Suspended Ceiling system with Optra(microlook) EDGE TILES WITH ARMSTRONG 15 mm Exposed GRID completeas per specification. Including all leads, lift and carriage complete.

Providing and fixing PVC wall panneling of approved brand and quality including moulding,corner and beeding complete job

Providing and fixing for Electrification/Lighting A. SITC of wiring .Providing primary lighht point using 2x1.5/2.5/4/6 mmstandard copper/FRLS PVC insulated wires for phase and neutral and 1.5 sq.mm green for earth laid in 25 mm dia PVC MMS conduit.Conduit shall be cleated to the surface/walls with saddles and spacers as per engg.practice.Rate to include all conduit and accessories,wires,complete and civil works and making good. B.Supply and fixing suitable size G.I Boxwith modular plate and cover in front of surface or in recess,including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch,connection,asrequired C. Supply and fixing following way ,prewired TP&PPI Distribution Bord of Sheet Steel for 415 Volts on surface/recess complete with ready to use DBs-provided with 100A insulated phase bus bars,neutral bar/s with shroud/earth bar, stickig saddles( cost OD D.B is without MCB's) D. LED 42 Watt/OSRAM CONCEAL DROP in LIGHT with 1 year warrenty excluding freight input Power: 42 W, INput Voltage :AC90-300v,50Hz Color temprature :6500l Beam Angle 12 No

Supllying & Commisioning Cassttee2.5 AC.It is exposedto atmosphere,salty air,wind,dust and corrosive chemicals.Blue Star's commercial spilt Acs (comlpete Job)

Supply of 1x8" Two Way Full Range PassiveSpeakers with 1" Compression Horn.Approved Make :CSC for AUDIO,VIDEO Etc (complete Job)

Supply of SwitchModePowerSupply Amplifire.Approved Make :CSC for AUDIO,VIDEO Etc (comlpete Job)

Supply of 8 Channels Mixers.Approved Make :Soundcraft for AUDIO,VIDEO Etc (comlpete Job)

Supply of Handheld Cordless Microphone.Approved Make :Shure for AUDIO,VIDEO Etc (comlpete Job)

Supply of 49" High Definition LED Display of approved brand (comlpete Job)

Supply of 8 in 1 Out A/V Switcher. Inputs :1xHDMI, Output : 8xHDMI. Bandwidth :Supports up to 2.25 bps bandwidth per graphics channel (comlpete Job)

Supply of HDMI Distribution Amplifire Approved brand Kramer (comlpete Job)

Supply of HDMI Audio Embedder Approved brand Kramer (comlpete Job)

Supply of Cable Cubby of Approved brand For PC Connectivity with 2VGA &2 Computer Audio Pass through cables.Durable enclosure that can be mounted into a tabletop or other top surface.Connectiors & Cables, Two 15- Pin VGA Female s with pass through cables,HDMI,3.5 mm& Ethernet. (comlpete Job)

Supply of Podium Cardioid Condenser Microphone with Desktop Base Element type : Electret condenser. rdioid Polar pattern : cardioid (comlpete Job)

Supply ofAll wires, Cables Connector,HDMI Cables,Clamps,Hanging Frame (comlpete Job)

Supply of Delegate Unit. Voice -activated microphone RFI protection,Pluggable gooseneck microphone stem.Waterproof and dustproof microphone pick -up range 12 to 18" . Red ring illuminant to identify active unit Blue LED indicator for Chairman Attendance:registration VOX sensitivity and mic time-out are adjustable. (comlpete Job)

Supply of Chairman Unit Voice -activated microphone mode RFI protection,Pluggable gooseneck microphone stem.Waterproof and dustproof design . Red ring illuminant to identify active unit Blue LED indicator for Chairman or VIP .Mounting type : Flush mounting Installation ,Testing & Commissioning Charges (comlpete Job)

Installation, Testing & Commissioning Charges (complete job) (Item No. 11 to Item No. 26)

Revolving Chairs:- The seat and back shall be made of PU foam of density 45 ± 2 Kg/m3 upholstered.Back Size: 480 mm. (W) X 550 mm (H) Approx. Seat Size: 480 mm (W) X 550 mm. (D) Approx. b. Base : Five prong made of black color reinforced PU plastic with Nylon wheels and pneumatic up & down with one point locking mechanism. c. Handle armrest : The armrest shall be gas-assisted injection molded from black polypropylene. d. Revolving & tilt : Chair should have a full 360o revolving mechanism with 17 deg. maximum tilt only and tilt tension adjustment facility e. Height of chair : Maximum and minimum height is approx. is 930mm and 830 mm respectively f. Powder coating : Other visible metal parts and seat base support metal parts should be powder coated with dry film thickness more than 50 microns, Salt Spray test to withstand more than 1000 hours, Pencil scratch hardness more than 2H, Adhesion as per DIN 53152 Standards. The powder coating shall be of good quality (7 process) to ensure good adhesion of life of the coating .

Chairman Chairs:- Dimension: Back: (W) 53 cm x (H) 80 Cm,Seat : (W) 54.6 cm x (D) 49 cm, Overall Dimensions of Chair:Seat Height - min 49.9 to max 58.9 cm.,Back Height - min 113.5 to 122.5 cm.,Width & Depth of Chair as measured from pedestal - Width 77 cm and Depth 77 cm Supplying and placing in position chair of the following specifications. The seat shall be made up of 1.2+/- 0.1 cm thick hot pressed plywood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of back shall be W-53cm, H-80cm & size of seat shall be W-54.6cm x D-49cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The seat and back should be arrested together with spine made of 0.8 +/- 0.05 cm thick HR steel and should be powder coated in black with 40-60 micron DFT (Dry film thickness). The armrest assembly should be made up of armrest tube, PU armrest and the armrest top.The armrest tube assy. shall be made of 2.54+/- 0.03cm x 0.16 +/- 0.0128 cm M.S E.R.W support tubes and chrome plated. The P.U armrest shall be made up of black integral skin polyurethane with 50-70 shore 'A' hardness reinforced with M.S insert. The armrest top shall be made up of ABS & upholstered with foam & leather. The mechanism of the chair shall have following features : 360⁰ revolving type,Knee Tilt system, Seat & back tilting ration of 1: 1.5, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 5-position locking with antilock back mechanismwhich should prevent the backrest from impacting the user when the lock is released, Static seat depth adjustment 5.0 +/- 0.5cm with 5 position locking. The chair shall be provided with pneumatic heightadjustment which shall have stroke of 9.0 +/- 0.3 cm. The bellow should be single piece duly blow moulded in black polypropylene. The pedestal shall be made of die-cast aluminium with buffing finish it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 67.0 +/- 0.5 cm pitchcentre-dia (77.0 +/- 1.0 cm with castors). The twin wheel castors shall be made of Nylon injection moulded in black color. Overall dimensions of Chair shall be, Width of Chair - 77cm, Depth of Chair - 77 cm as measured from pedestal below. Height of back from ground - min 113.5 to max 122.5 cms. Seat height - min 49.9cm to max 58.9 cm. Dimensions tolerance / variations shall be within +/- 1 cm

Cantelevar Chairs:- Dimension: Back: (W) 53 cm x (H) 80 Cm,Seat : (W) 54.6 cm x (D) 49 cm, Overall Dimensions of Chair: Seat Height - min 49.9 to max 58.9 cm.,Back Height - min 113.5 to 122.5 cm.,Width & Depth of Chair as measured from pedestal - Width 77 cm and Depth 77 cm Supplying and placing in position chair of the following specifications. The seat shall be made up of 1.2+/- 0.1 cm thick hot pressed plywood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of back shall be W-53cm, H-80cm & size of seat shall be W-54.6cm x D-49cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The seat and back should be arrested together with spine made of 0.8 +/- 0.05 cm thick HR steel and should be powder coated in black with 40-60 micron DFT (Dry film thickness). The armrest assembly should be made up of armrest tube, PU armrest and the armrest top.The armrest tube assy. shall be made of 2.54+/- 0.03cm x 0.16 +/- 0.0128 cm M.S E.R.W support tubes and chrome plated. The P.U armrest shall be made up of black integral skin polyurethane with 50-70 shore 'A' hardness reinforced with M.S insert. The armrest top shall be made up of ABS & upholstered with foam & leather. The mechanism of the chair shall have following features : 360⁰ revolving type,Knee Tilt system, Seat & back tilting ration of 1: 1.5, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 5-position locking with antilock back mechanismwhich should prevent the backrest from impacting the user when the lock is released, Static seat depth adjustment 5.0 +/- 0.5cm with 5 position locking. The chair shall be provided with pneumatic heightadjustment which shall have stroke of 9.0 +/- 0.3 cm. The bellow should be single piece duly blow moulded in black polypropylene. The pedestal shall be made of die-cast aluminium with buffing finish it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 67.0 +/- 0.5 cm pitchcentre-dia (77.0 +/- 1.0 cm with castors). The twin wheel castors shall be made of Nylon injection moulded in black color. Overall dimensions of Chair shall be, Width of Chair - 77cm, Depth of Chair - 77 cm as measured from pedestal below. Height of back from ground - min 113.5 to max 122.5 cms. Seat height - min 49.9cm to max 58.9 cm. Dimensions tolerance / variations shall be within +/- 1 cm

Repair & Polishing of Conference Table having top made of 3mm thick Vinear,shall be polished with melamine polished.The table shell have provision for carring wires&mounting switches and cutting for cable cubby boxes etc complete in all respect

Providing wood work in fames of doors, windows, clerestory windows and other fames, wrought framed and fixed in poisition with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteeners shall be paid for separately) Sal Wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 10kg /sqm (4 mm thick) float glass panes inclding ISI marked M. S pressed butt hinges bright finished of required size with necessary screws. 35 MM second class deodar wood

Polishing on wood work with readymade wax polish of approved brand and manufacture on new work

EDILE ENGINEERING PRIVATE LIMITED

AVG Contracts and Supplies pvt ltd