SPECIAL REPAIR TO KRISHNA BLOCK BLDG NO T-191 TO 194 AND T-195 TO 197 AT INS SHIVAJI, LONAVLA

Amount

Dismantling of CGI/PGI sheet roofing any gauge and any thickness including ridge, valley gutter etc.

Pre painted galvalume aluminium zinc coating GI based Mangalor Pattern steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified.

S&F Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, Rainwater gutter fixed with self tapping screws as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

M&L for preparation of new steel surface of steel and applying two coats of synthetic enamel paint over a coat red oxide primer

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets/Aluminium snap grid

M&L for powder coated aluminium snap grid frame work for false ceiling, with aluminium angle 25mmx25mmx1.5mm fixed to perimeter of wall, Main 'T' runner 38mmx25mmx1.5mm and secondary/cross 'T' runner 25mmx25mmx1.5mm to be interlocked in such a way that the size of grid shall be 605mmx 605mm including 6mm dia GI hangers (upto 1200mm length) adjusting level fixed to roof by means of ceiling cleats made out of GI flat 40x3mm, 60mm long and expansion hold fastners 12.5mm dia, 40mm long complete all as specified and as directed. Note:- The thickness of the powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE.

S&F 4 mm thick Non Asbestos (E-board) designer tiles (Electra) suitably fixed in false ceiling grid /frame with staples or screws complete all as specified and as directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for granite(of any type) work(table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platform and like set in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to matach with shade of granite thickness of granite 20 to 25mm.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for Glazed Coloured ceramic tiles in vertical surfaces 300X600 mm set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for rendering 10mm thick in CM 1:4 as in backing coat of as in skirting and glazed tiles in walls.

M&L for Screed bed or bedding layer of mortar (1:6) 20 mm thick for laying floor finishes.

S&F for Renewing glazed wall tiles in patches, area n exc 5 sq. m. including cutting out broken tiles, removing and cleaning loose tiles, preparing bed, removing rubbish and replacing old with new tiles to match, complete with all cuttings, etc. and laying or setting, jointing and pointing new or old tiles complete

M&L for 75 mm thcik Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in plinth protection

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Rendering in cement mortar 1:4 15mm thick (10mm as doubing coat and 5mm in finishing coat using water proofing compound on brick/ stone surfaces finished fair and even without using extra cement etc complete all as specified and directed.Note : Water proofing compound and will be measured and paid separately.

Supply only integral water proofing compound.

M&L for Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shad (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over Newly Plastered Surfaces

Demolition of brick/stone masonry built in cement mortar incl coping etc complete in any position, locations etc complete all as specified and directed incl removing the unserviceable debris as specified and as directed by Engr-in-charge.

PCC (1:4:8) type D2 (using 40 mm graded stone aggtegate) as in foundation filling and mass concrete

M & L for walling of random rubble uncoarsed, well bonded, bedded and solidly hearted,built in CM 1:6

Provide cement concrete of 1:2:4 (20mm graded aggregate) type B1 for coping.

Extra over stone walling for hammer dressing 20 mm to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses

M & L for rendering 20mm thick cement plaster (1:6) on stone masonry

Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment

M&L for complete removal of old existing treatment and applying two coats of Oil Bound Distemper over a coat of alkali resistant Primer over 3mm thick putty of approved make all as specified and as directed.

M&L for preparation of old plastered surface of ceiling surface and applying three coats of white wash etc all as specified and directed.

M&L for preparation of old painted steel surfaces of any description having width or girth exceeding 10cm and applying one coat of synthetic enamel paint complete all as specified & as directed.

M&L for preparation of old painted surfaces of wall and applying Two coat of exterior grade, weather resistant antifungal acrylic latex paint complete all as specified and directed.

Dismantling of cast iron/PVC or reinforced concrete drain pipes, jointed in cement mortor and taking out of trenches/wall if required 100/75 mm internal dia pipe complete all as specified.

S&F PVC (SWR) pipes of dia 110mm bore single socketed in any length with rubber ring joints fixed to walls with suitable GI Clamps

S&F PVC (SWR) pipe of 75 mm bore in single socketed in any length with rubber ring joints fixed to walls with suitable GI Clamps

S&F PVC(SWR) vent cowl of 75mm dia bore.

S&F PVC(SWR) vent cowl of 110mm dia bore.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal 75 mm dia

S&F PVC (SWR) branch piece, single (single Y) equal or unequal 110 mm dia

S&F PVC (SWR) bends of 75mm dia bore with access door

S&F PVC (SWR) bends of 110 mm dia bore with access door

S&F in repairs High density polythylene (HDPE) pipes 50 mm dia, of pressure rating 6 Kg/sq cm, fixed to walls, ceilings or in floors complete all as specified and as directed.

Cutting holes in brick wall or stone walls built in cement mortor for inserting hold fast and making good the disturbed portion in cement mortor 1:3 or cement concrete (1:2:4), type B1 as requried for depth of embedded portion of hold fasts or lugs measured from the face of the Jamb into the wall exc half brick & N.exc one brick all as specified and as directed.

S&F PVC Nahani trap 100mm size with grating including hacking out cement joints and jointing to existing pipes/ waste pipe fixed in cement concrete type type B1 (1:2:4)

S&F in repairs, vitreous china wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S & F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

S&F 10 Litre PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets

S&F in repairs for vitreous china urinals half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortor (1:2), securing urinals to plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush pipe, spreader,grating and union for discharge pipe complete all as specified and as directed.

S&F Flush pipe of polyethylene of low or high density or PVC, 32 mm dia, for low level cistern

Dismantling water tanks of any type of capacity n exc 2000 and removing

S&F Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) 2000 ltrs capacity hoisted and fixed in position all as specified

Taking up or down steel tubing of bore 15/20 mm and connection, including cleaning for refixing or removal complete all as specified.

Taking up or down steel tubing 25/32 mm and connection, including cleaning for refixing or removal to store complete all as specified.

Taking up or down steel tubing 40/50 mm and connection, including cleaning for refixing or removal to store complete all as specified.

S&F CPVC pipes, SDR 11 , 25 mm outer dia conforming to IS - 15778 with all fittings such as Tee, bends ,elbows, unions sockets and end oieces etc to receive the fittings and fixed with solvent in trenches complete.

Ditto as per Item above but of 20 mm dia

Ditto as per Item above but of 40 mm dia

S&F in repairs ball or float valve 25 mm brass high pressure with polythene float and fly nut etc complete fixed in repairs.

S&F PVC connection low density polythene pipe 15 mm dia , 450 mm long , heavy duty with PTMT nuts

S&F Pillar taps 15 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F Bib tap cast copper alloy chromium plated, fancy type, 15 mm bore fixed in repair.

S&F Stop valves cast copper alloy,chromium plated fancy type long shank and cup screwed down, screwed for iron/ CPVC pipes high pre-ssure, with crutch or but-terfly handle, screwed both ends suitable for 15 mm pipes

S&F stainless steel soap tray fancy type fixed in repair. Jaquar cat no ACN-1131N

S&F in repairs hand shower (Health Faucet), chromium plated with 8mm dia, 1.20m long flexible tube with wall hook all as specified and as directed. Cat No:- ALD - 573 of Jaquar or equivalent model Manufactured by Esess/ Marc.

S&F 20mm dia towel rail chromium plated 60cm long including bracket. Make - Jaquar cat No ACN-1111SM or equivalent.

S&F brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union.

Taking down chowkats with shutters( without taking off shutters from the frame) exc1.5 sqm and n.exc 4 sqm each

Taking down chowkats or frames N.exc 1.5 Sqcm with shutter (without taking of shutter from the frame.

S&F factory made PVC double door frame of size 50 mm x 95 mm made out of 5 mm single side prelaminted PVC sheet reinforced with MS Square tube all as specified and as directed .

S&F for 30 mm Factory made Moulded door shutter - Wood free consisting of frame made out of M.S. tube of 19 gauge thickness and size of 25 mm X 25 mm for stiles, top and bottom rails M.S. frame shall have a coat of steel primer. The inner panel shall consist of 25 mm thick High density EPSconforming to IS 4671-1984 bondedwith 2 mm termite proof, water proof and fire resistant molded PVC sheet with 2,4,6 raised panel designs in different plain and / or prelam colours after routing the Moulded design on one side & 2 mm plain and / or prelam PVC sheet on other side of the EPS. The edge of the panel is to be sealed with lipping of 10mm wide PVC sheet baton (made by sticking 2 nos , PVC sheets of 5 mmt thickness using PVC solvent cement ) and stile sides 25 mm (5mm x 5)thick and 30mm wide PVC sheet fitted along M.S tube for lock provision & for lock height 5 mm thick PVC sheet of 150 mm x 100 mm fixed with upper & lower face of inner side of EPS panel and manufacturer's specification & drawing etc, complete all as specified and directed.

S&F for 30 mm thick Factory made fully glazed solid PVC Door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for stile and 15 mm x 15 mm for top, lock and bottom rail MS frame shall have a coat of steel primer of approved make and manufature MS frame shall be covered with 5 mm thick heat moulded PVC C channel of size 75 mm x 30 mm x 50 mm out of which 10 mm shall be bent at 90 degree towards inner side on front face of the door forming stile, for Top and Bottom rail MS frame shall be covered with 5 mm thick, 100 mm wide PVC sheet out of which 10 mm shall be bent at 90 degree towards inner side on front face of the door. MS frame at Lock rail shall be coverved with 125 mm wide PVC sheet out of which 10 mm both the adjust shall be bent at 90 degree on front face of the door and 75 mm wide PVC sheet shall covered the MS frame at top lock and bottom rail on back side of the door 5mm thick 20 mm croos PVC sheet as gap insert for Top and Bottom rail. PVC sheet beading of 10 mm thickness (5 mm x2), 25 mm wide to be stuck internally in the front face of the stiles and rails of the doors and 10 mm thick ( 5mm x 2), 15 mm wide and PVC sheet beading to be stuck internally in the back side of the stiles and rails of door with solvent cement adhesive,stainless steel wire mess will be fitted exteranlly in the clear face availabe between the stile and rails and fixed between PVC sheet of stiles and rails bent at 90 degree on front face 15 mm x 10 mm, 'L' shape outer beading nailed on stiles and rails at the back side so that the 'L' shape PVC beading can be removed when required for replacement of broken wire mess etc and manufacturer's specification & drawing etc, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F for 35 mm Factory made Moulded door shutter consisting of solid core single leaf flush door of 30 mm thickness,lipped with 15 mm (5mm x 3) thick x30 mm width on the other stiles & bottom rails & 10mm (5mm x 2) thick x 30 mm width on other stiles & bottom rails , The inner panel laminated with 2 mm thick termite proof, water proof and fire resistant molded PVC sheet with 2,4,6 raised panel designs in different plain and / or prelam colours after routing the Moulded design on one side & 2 mm plain and / or prelam PVC sheet on other side using rubber adhesive on flush door & solvent cement adhesive on the PVC Lipping and manufacturer's specification & drawing etc, complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staples.

S&F for 4 mm Sheet glass, ordinary quality and glazing as in Aluminiu windows, Doors, Ventilators etc in square/ rectangular shape n exc 0.5 sq.m in each pane including taking out and removal of old glass all as directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 100 mm thick Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F Aluminium bow handles, cast type, anodised 150 mm long

S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed

Taking down steel/aluminium windows/ventilator of any size with all fittings complete

S&F aluminium powder coated ventilator partly fixed and partly louvered type without sash of bars, section as per designation 63400 of IS 737, frame and intermediate made out of aluminium section of size 50.80 x 25.40 x 0.95 mm (Catalogue No 14027 of M/s Jindal) including necessary heavy duty louvers (adjustable with locking arrangements), jointing clips, rubber packing, anodised snap beading, screws alongwith 4.00mm thick pin headed glass for louvers and glazing etc complete all as specified and as directed. Note:- (i) The thickness of the powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE. (ii) Sealing the gap of frame with Jamb and Cill (alround) using silicon gel at the rate of 0.05 lit/m for both faces of window.

Removing building materilas such as bricks, stones, concrete, sand etc to a distance upto 15Km, beyond the lead included in the rates, including loading, unloading and stacking at the destination.

M&L for powder coated aluminium three track and three shutter (of equal width) sliding type window without sash bars including necessary jointing clips, rubber packing, neoprene rubber gasket, aluminium snap beading, screws, aluminium fittings, handles, locking arrangement (star lock), bearings two No's for each shutter with 4.00mm thick sheet glass for glazing shutters & stainless steel wire cloth of 0.36mm nominal dia of wire & average width of aperture 1.40mm for wire gauge shutters including following powder coated sections as given in 'JINDAL' catalogue complete all as specified and as directed :- (i) Frame (Bottom)-20620. (ii) Frame (Top & Side)-20621. (iii) Shutter vertical (Handle lock)-20846. (iv) Shutter vertical (Int lock)-20845. (v) Shutter (Top)-20844. (vi) Shutter (Bottom)-20847. Note :- (i) The window opening shall be provided with three shutters of equal width. (ii) Two shutters shall be glazed shutters & one shutter shall be with stainless steel wire cloth all as specified hereinbefore. (iii) The shutters shall be placed in such a manner that at a time the entire width of window can be utilized as fully glazed window and at time the same can be utilized as partly glazed and partly gauzed window. (iv) The thickness of powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE. (v) Sealing the gap of frame with Jamb and Cill (alround) using silicon gel at the rate of 0.05 lit/m for both faces of window.

S&F GI tubing 20mm bore medium grade with all fittings and fixed to wall and ceiling laid in floors complete

S&F GI tubing 32mm bore medium grade with all fittings and fixed to wall and ceiling laid in floors complete

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M & L for Point wiring with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box fixed with suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed. (a) One light point or one fan point or bell point controlled by one switch

All as per item No 89 but One 3 pin socket outlet, 5 Amp independent

All as per item No 89 but One 3 pin socket outlet, 5 Amp on the same board with other switches

All as per item No. 89 here in before but wiring with cables of size 2.5 sqmm for wiring & cables of size 2.5 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 3 pin Switch/Socket outlet on Independent board complete all as specified and directed. (Note : cutting chases & making good of disturbed surfaces shall be measured and paid separately).

S & F switch piano, 5 Amp, single pole, flush type one way 230 volts complete all as specified and as directed.

S & F socket out let, 2 in 1, 3 pin, 5 Amps, 240 volts complete all as specified and directed.

S & F Switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts complete all as specified and directed.

S & F Switch socket combination, 5 in 1, 5/15 Amps, 240 volts, flush type complete all as specified and directed.

S & F Ceiling rose, 3 way PVC insulated body complete all as specified and directed by engineer in charge.

Labour only for taking down and fixing repairs to Ceiling Fan, Exhaust Fan, any Make & any Sweep Oiling, Greasing , removing all dust with painting and Rewinding of fan by super ennameled copper insulated wire as per existing gauge, varnishing, heating assembling and testing for following complete all as directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.Make: Crompton or equivlent Bajaj/Philips/Havells

Taking down of Old MCB DB / control box any type any size including MCBs and separating the serviceable MCB DBs and MCBs for reuse at site

S&F in repairs MCB DB TPN 8 ways double door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed

S&F in repairs MCB FP 63 Amps 240/415 V , with adjustable thermal and adjustable magnetic release,Make- HAVELLS,Cat No-D-VGCFPF038 or equivalent to Standerd/Legrand Complete all as specified and as directed.

S&F in repairs MCB SP 6 to 32 amps single pole 240 Volts, Complete all as specified and directed.

S&F in repairs MCB SP 32 to63 amps single pole 240 Volts, Complete all as specified and directed.

Removing and Re- fixing existing electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories.

S &F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 A SP. Make : Standard/Havells

M&L for earthling complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 6.0 mm dia by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR part1991,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on complition.

VIJAYA ENTERPRISES

Mehta Construction Co.

SAI SAMARTH ENTERPRISES

KARPE AND SONS CONSTRUCTION

DWARKESH STRUCT-CON

RK AND SONS CREATION

M/s S.D Construction Co

M/S ANAND G NUNSE