For the Work of Business Plan 2024-25 For Installation of 03 No. Additional 250 KVA Transformer Due to Overloading of 400/630 KVA Transformer and Installation of New 33 KV Control Panel and VCB at 33/11 KV Sub-Station Under EUDD-I, Meerut.

Amount

Cartage of line Material from Central Store to JE store including loading & unloading at both ends.

Cartage of line Material from JE store to various site of work including loading & unloading at both ends.

Cartage of 11 mtr long ST pole from Central Store to JE Store including loading and unloading at both ends.

Cartage of 11 mtr long ST pole from JE Store to Various Site including loading and unloading at both ends.

Cartage of 250 KVA T/F from Central Store to JE Store including loading and unloading at both ends.

Cartage of 250 KVA T/F from JE Store to Various Site including loading and unloading at both ends.

Erection of Double Pole Structure on 11 Meter ST Pole with Stone Pad including Fabrication & Fixing of Top Channel, Dropper Channel suitable for 250KV A Transformer. (As per RESPO construction mannual)

Making a plinth of size suitable for 400/250 KVA T/F 3x2x1.0 m above ground level and 01 fit. Below ground level after digging of earth brick ballast shall be provided and remerging will be done properly after that a retaining wall of 9 width by first class brick in ratio 1:4 of cement and sand will be made. The earth shall be filled upto 1 feet below the top of the plinth after this brick ballast shall be provided upto 6 from the earth level and proper remerging shall be done 1 no. jall of 12 mm shall be fixed in the hollow of plinth and four inches thick RCC in 1:2:4 ratio of cement, sand, stone ballast shall laid on the top of the plinth.

Making a fencing suitable for 250/400 KVA T/F Plinth. Including Providing, Fabrication and Fixing of wire mesh fencing frames of size 3.0x2.0x2.0 mm fabricate out of MS Angle iron of size 35x35x6 sq.mm having 02 No. legs of 15cm long in each frame duly welded and fixing with wire mesh of size 25x25x10 SWG hot dipped galvanized with in the frame pressed under MS flats of size 25x5 mm inside the angle on all four side with help of approx 20 No. bolt and nut of 10 mm diameter 15 cm legs of frame will be grouted in 1:2:4 cement coarse sand and 20 mm gauge stone ballast with paint with one coat of red oxide and two coat of aluminium paint of approved mark after proper cleaning.

Safely mounted 250 T/F on double pole structre/plinth and making jumpring and binding making all connection properly.

Water level earthing of neutral and body of distribution transformers of 11/0.4 kv transformers by boaring of earth upto water level (15 to 20 Mtr.) and lowering of GI Pipe 32 mm dia upto water level and connecting the same by ms flate of size 40x4 mm with transformers. The transformer will be earthed properly including/cutting, jointing, welding etc. of MS Earth Strip and connecting one earthing with the neutral bushing of transformer and other to the body of transformer at several points. The GI Pipes will be connected to each other with the help of G.I. Sockets and a cap will be provided on the upper part of the G.I. Pipe for pouring of water during summer season./ chemical earthing

Laying, lagging, sagging of Weasel Conductor

Laying of L.T. ABC (3x120 sq mm)

Laying of L.T. PVC ;cable Al (1x400 sq mm)

Providing of earthing rods and Earthing of poles with earthing rod complete in all respect.

Fabrication and fixing of Channel ,Angle as per site requirement .

Providing and Fixing of LT Aluminum Crimping Lugs as per site requirement

Providing & Fixing of 11 KV Fuse Set on 250 KVA Transformer properly complete work in all respect.

Providing and Fixing of Tailless unit as per site requirement .

Providing and Fixing of all type off size Clamps(suspension,Dead end ,Holding,J-Huk) as per site requirement.

Providing and Fixing Nut and Bolts off size.

Grouting of poles in CC in ratio 1:4:8 in cement, sand and brick ballast.

Providing & Fixing of Distribution Box 3-Phase

Providing & Fixing of Distribution Box 3-Phase Clamps with Nut & Bolts

Fixing of 11 KV Pin Insulator with pin.

Fixing of 11 KV Disc Insulator with pin.

Part-A

Cartage of Control Panel from central store to 33/11 K.V. S/S ( site of work) including loading and unloading at both endes.

Dismentling of Control Panel by Opening of Control Panel Cable / Leads and Shifting of Damaged Control Panel to the safe side in all respect.

Installation of Control Pannel by Fixing of Control Panel Leads/Relay etc. complete in all respect.

Cartage of VCB from central store to JE Store and from JE Store to work site including loading and unloading at both endes.

Dismentling of Old and Damaged 33 KV VCB by opening the cable/lead and making free

Shifting of old VCB to the safe place .

installation of 33 KV VCB by making connection through Lead/Cable properly.

Providing and Fixing of 33 KV Line Isolator

Providing and Fixing MS Angle for Structure (CT & Isolator)

Providing and Fixing Nut & Bolt.

Received Back of Material

Cartage of VCB/OCB from site of work to J.E. store and J.E. store to central store including loading and unloading at both endes.

Cartage of Control Panel from site of work to J.E. store and J.E. store to central store including loading and unloading at both endes.

Part-B

Cartage of Line Material from central store to JE store and Je store to site of work including loading and unloading at both endes.

Errection of Poles Complete in all respect.

Grouting of Poles.

Earthing of Poles.

Providing and Fixing Holding Clamp.

Laying of 11 KV XLPE cable 3x120 sqmm. (Double Circuit)

Providing and Fixing of 11 KV XLPE cable 3x120 sqmm Jointing Kit.

Providing and Fixing of TPMO Set.

Providing and Fixing HDPE Pipe for U/G Cable

Providing and Fixing of MS Chanel. 50x50x6 mm.

Providing and Fixing Nut & Bolt.

VISHNU TRADING CO.