CA NO GE (A) SOG-TOKEN NO 57/25-26 COMPREHENSIVE MAINTENANCE OF B/R AND E/M REPAIR WORK AT ASCON NODES UNDER GE (ARMY) SURATGARH AT SURATGARH MIL STN

Amount

M&L as in repair providing cement concrete RCC Jalli 35mm thick type B0 1:2:4 using 12.5mm graded aggregate (measured solid) including all moulding and pillars complete all as specified and as directed by Engineer-In-Charge.

Dismantling of timber scantling of any description of any section unframed work and in any position complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with fly ash bricks old size bricks straight or curved on plan to any radius built in CM 1:6 including demolition of existing brickwork in any position and of any description complete all as specified.

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc and M&L for Rendering 10 mm thick on fair faces of brick or concrete Surfaces in cement mortar 1:6,even and smooth w/o using extra cement including preparation of newly decorated, plastered or pointed surfaces of wall and applying two coats of interior emulsion over a 1 mm thick acrylic wall care putty over a coat of pirmer complete all as specified & directed by Engineer-in-Charge. (Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or equivalent Technocommercial make mentioned in Appx 'A' here in after.

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc and M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4.including taking out existing plaster and raccking out all joints and surface shall be finished with one coat of alkali resistant primer and two coat of cement base paint of approved tint completely and all specified and as ditected by Engineer-In-Charge. (Note: Plaster shall be carried out in patches and contractor shall have no claim for any height and scaffolding what so ever is the location)

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc and M&L for rendering 5 mm thick on fair faces of concrete Surfaces in cement mortar 1:3,even and smooth w/o using extra cement as on ceiling.and finished preparation of newly decorated, plastered or pointed surfaces of wall and applying two coats of interior emulsion complete all as specified & directed by Engineer-in-Charge. (Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or equivalent Technocommercial make mentioned in Appx 'A' here in after.

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc and M&L 15 mm thick rough cast plaster in Cement mortar 1:4 consists of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with course sand and cement in the ratio of 1:1:1including reparation newly plastered and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-Charge. (Make :- Apex Ultima (Asian Paint), Weather Coat anti dust ( Berger Paint ), Excel No Dust ( Nerolac) or equivalent Technocommercial make mentioned in Appx 'A' here in after. Note: The rate quoted shall be deemed to include for necessary use and waste of form work if required and nothing extra shall be paid on this account).

M&L Providing PCC 1:4:8 as in sub base/mass concrete type D-2 using 40mm graded stone agg including demolition of existing PCC of any description complete all as specified and as directed .

M&L for 40 mm thick PCC type B-1 ( 1:2:4) 20mm graded aggregate as in PCC flooring as in surface finished including demolition of existing PCC surface laid in pannels made up of 3 mm thick PVC dividing strip 38 mm wide complete including demolition of exiting floor of any description all as specified and as directed by engineer-in-Charge.

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors/vertical surface skirting on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete. including demolition existing tiling with cement mortar bedding (but not backing) complete all as specified and directed by Engineer-in-charge. Note:- Colour and shade shall be approved by GE

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors/vertical surface skirting on 10mm thick rendering in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.including including demolition existing tiling with cement mortar bedding (but not backing) complete all as specified and directed by Engineer-in-charge. Note:- Colour and shade shall be approved by GE

M&L for 7-8 mm thick Vitrified coloured tiles of size exc 0.18 Sqm but not exc. 0.36 Sqm as in floors over 15 mm hick screeding in CM 1:6 jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces including demolition existing tiling with cement mortar bedding (but not backing) complete all as specified and directed by Engineer-in-charge. Note:- Colour and shade shall be approved by GE

M&L for 7-9 mm thick Vitrified coloured tiles of size exc. 0.42 Sqm but not exceeding .1.00 Sqm as in floors over 15 mm hick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces including demolition existing tiling with cement mortar bedding (but not backing) complete all as specified and directed by Engineer-in-charge. Note:- Colour and shade shall be approved by GE

M&L for Glazed ceremic tiles white 600X300mmX7mm thick coloured,set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floor tiles as on vertical surfaces laid over 10mm thick cement screed in 1:4 including demolition existing tiling with cement mortar bedding (but not backing) complete all as specified and directed by Engineer-in-charge. Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same

S& F as in repair 5 mm thick hollow PVC lining/Panneling to walls of wooden textured and colour as approved complete with necessary L and U shape edges complete all as specifed and as directed .

S&F as in repair 25 mm outer dia CPVC pipes SDR 11 & Plain/Brass CPVC SDR 11 fittings in walls complete all as specified and as directed by engineer-In-Charge.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including demolition exisitng PCC complete all as specified and as directed

M&L Sand stone slab 25-35mm thick set jointed and pointed self faced punched dressed laid as in chhajas, sunshade and man holes covers set in cement mortar 1:4 incl.making chases in wall including demolition exisitng stone slab complete all as specified and as directed

M&L Granite 20 mm thick of any type work table rubbed and polised in steps,jambs,pillars,window cill, cooking plateforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixure of pigments to match with shade of granite over 15 mm thick screed bed of CM 1:6 including demolition exisitng stone slab complete all as specified and as directed

M&L for rolled section ( Square/Rectangular section Confirming to IS 4923 ) as in main and cross beams , purlins , rafters ,posts where connected to common rafter and running rails etc conforming to Fe- 410-w/ Gde 240 including demolition of exiting wooden/steel work complete all as specified and as directed by Engineer-In-Charge.

M&L for steel Work in tubular trusses including special sahped washers etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St. 240. including dismantling of existing wooden/steel trusses complete all as specified and as directed by Engineer-In-Charge.

M&L Pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.6 mm thick Company Rolled of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws including dismantling existing sheet complete all as specified and as directed. MAKE :- TATA DURASHINE/JSW Colouron+/JINDAL Neu Color +) Note:- Contractor Shall Submit Manufacturer Warranty certificate from manufacturer .

M&L Pre-painted galvalume aluminium zinc coating AZ-150 GI based Plain steel sheet 0.6 mm thick Company Rolled of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws including dismantling existing sheet complete all as specified and as directed. MAKE :- TATA DURASHINE/JSW Colouron+/JINDAL Neu Color +) Note:- Contractor Shall Submit Manufacturer Warranty certificate from manufacturer .

S&F Composite cement designer ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest ramco or eql.) designer ceiling pre finished conforming to IS 14862 type B cateogory three incl powder coated GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster .) including dismantling exisitng ceiling board complete all as specified and as directed

S & F as in repair stainless steel tubular curtain/drapery rod 25 mm dia ( in length as directed) with & including pair of projecting type fancy stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on wall/beam complete all as specified and as directed .

Taking down chowkhat or frame with shutter (Without taking off shutter ) exc 1.5 sqm but n exc 4 Sqm and M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm double Rebated comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant.and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.

Taking down chowkhat or frame with shutter (Without taking off shutter ) n exc 1.5 sqm and M&L in Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65x100 mm single rebated comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant.and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made Flush door Shutters 30 mm thick , solid core construction, with block board core and plywood face panel , commercial type on both side complete. confirming to IS 2191 (Part 2) : 2022 Including edges of door covered with teak wood 5 mm bidding including fixing of 2 nos Steel handels 150mm on each Leaf with miniumm 3 nos SS Butt Hinges and 1 Nos Tower Bolt 200 mm long of Stainless steel and 1 nos Latches 250 mm long and 1 nos sliding door bolt 300 mm of Stainless steel complete including taking down existing door and depositing same in to Engineer-In-Charge store complete all as specified and as directed By engineer-In-Charge..

S&F factory made 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc, without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I section 8, clause 8.20 (a) supplied and fixed to chowkats including all necessary butt hinges, door handles, tower bolt complete all as specified and as directed by Engineer-In-Charge.

M&L for Providing factory made 30 mm thick 100 % Solid WPC ( Wood Polymer composite) solid plain flush shutter of required size comprising of virgin PVC resin of K-value 57-60 ( Suspnsion grade), calcium carbonate and natural fibers( wood powders/rice husk/wheathusk) and non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with having minimum density not less than 650 kg/cbm manufactured by a ISO-9001-2015 certified comany,having good screw holding capacity (screw withdrawl strength of 2000 N (Face) & 1100 N Edge), Minimum compressive strength of 50 N/mm2, Modulus of elasticity 850 N/mm2 and resistance of spread of flame of class A category with property of being Termite/Borer Free, water/Moisture Proof and fire Retardant. WPC to be laminated with PVC foilof minium 14 micros thick of approved design pasted on both faces of shutters and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter shunk SS screws. All as per direction of Engineer-In-Chrage, material test certificate and authentication should be compulsory provided by the manufacturing company: For PVC/BATHROOM/TOILET/KITCHEN/BALCONY DOORS and CABINETS

M&L for powder coated aluminium of any colour (minimum thickness of powder coating 50 micron) for shutters/Frames of doors, windows & ventilators. including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall not be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285,Aluminium handles, tower bolts , fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all including taking down exisitng steel window/ventilator complete as per architectural drawings and the directions of Engineer-in-charge. Note:- Minimum Weight of Any Section for Frame/Shutter Shall Not Be less than 1.00 Kg/Rm. Make :- Jindal/Nalco/Hindalco or other technocommercial make mentioned in Appx 'A' here in after

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

S&F as in repair sheet glass 5.5 mm thick ordinary quality & glazing with rubber gasket in squares exc 0.5sqm in each pane as in aluminium door/window complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including if required taking down existing unserviceable Wire complete all as directed by Engineer-In-Charge.

S&F as in repair viterous China urinal half stall type white including CP spreader,Cp Angle cock and urinal waster pipe with coupling complete all as specified and as directed.

S&F as in repair vitreous china wash down water closet Orissa pattern white of size 550x440mm including integral foot rest including 10 liters PVC Flushing cistern with PVC L bend and all Necessary Items includng 1 Nos Bib tap Fancy Type ISI Marked Chromium plated , 1 nos Angle Valve Brass Chromiuum Plated ISI Marked and 1 Nos 600 mm long PVC connection incl. P or S trap complete all as specified and as directed Make :- Parryware/Hindware/Jaquar or other technocommercial make mentioned in Appx 'A' here in after

S&F as in repair water closet pedestal patteren white or coloured Single Piece suite P or S trap incl Seat cover) or equivalent in Note:- 2 nos Cp Angle valve, 1 nos Steel braided hose 600mm long connection , 1 nos 1.0 m long pipe with health faucet as approved by Engr-In-Charge. Make :- Parryware/Hindware/Jaquar or other technocommercial make mentioned in Appx 'A' here in after

S&F as in repair 15 mm bore bib tap brass chromium plated fancy type Quarter turn with min weight as Per Relavent IS standard complete all as specified and as Directed. Make :- Kohler/Hindware/Somany or other technocommercial make mentioned in Appx 'A' here in after

S&F as in repair 15mm bore angle cock chromium plated fancy type Quarter turn with min weight as per relavent IS standard complete all as specified and as directed . Make :- Kohler/Hindware/Somany or other technocommercial make mentioned in Appx 'A' here in after

S&F as in repair PVC (SWR) floor trap plain 75mm dia with PVC grating including jointing with solvent cement complete all as specified and directed by Engineer- in - Charge.

S&F PVC(SWR)single socketed in any length with rubber ring joint fixed with wall / laid in foor complete of 110mm as in rain water/ waste pipe complete including all necessary Bends , branch Pieces and reducers with solvent fixed complete all as specified and as directed by engineer-In-Charge .

S&F PVC(SWR)single socketed in any length with rubber ring joint fixed with wall / laid in floor complete of 75 mm as in rain water/ waste pipe complete including all necessary Bends , branch Pieces and reducers with solvent fixed complete all as specified and as directed by engineer-In-Charge .

Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 44 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches.

All as per serial item No. 44 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board.

All as per serial item No. 44 here-in-before but for One light point controlled by Two 2- way switches.

All as per serial item No. 44 here-in-before but for One bell or buzzer point controlled by by one push button on independent board.

All as per Srl item No. 44 above, but wiring with cable of cross sectional area 4 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 4 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular switch piano 6 Amps single pole, two way, 01 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular switch piano 15/16 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular socket 2 / 3 pin, 6 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular socket 2 / 3 pin, 6/16 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular bell push, flush type, 5 Amp, 230 Volts grade complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular Switch socket Combination 5A, 3 pin, 3 modular, 230 Volts grade complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular Switch socket Combination 16A, 6 pin, 3 modular, 230 Volts grade complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular electronic fan regulator suitable for ceiling fan 2 Module, 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair sheet metal plug & socket DB, SP, with a two pin and earth plug with socket, 230 Volts with & including one MCB SP ‘C’ Curve 10 kA, 20 Amps complete all as specified and directed by Engineer-in-charge.

S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F electric bell (ding - dong), AC, 230 Volts, Single pole & connecting up complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W020/Crompton Cat Part CCS-103-20-65-SL-DP-NWH/Wipro Cat Part D532065 or equivalent cat part of Make as specified in Appendix "A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 10 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W010/Crompton Cat Part CCS-103-10-65-SL-DP-NWH/Wipro Cat Part D531065 or equivalent cat part of Make as specified in Appendix "A".

Supply and fixing LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing LED luminaire surface/ceiling light, 12 watt, 220 V AC recessed type with opal diffuser complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make : Havells Cat Part No.:- LHEABMP7UL1W012/Crompton Cat Part LCDSPLN-R-12CDL/Wipro Cat Part D641265 or equivalent cat part of Make as specified in Appendix "A".

Supply, fixing and testing in repair LED Street / Security light fitting of 30 Watt, 5700K - 6500 K (including LED drive and internally prewired) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with IP -65 / 66 protection as per IS - 10322-1982(Part -I) with latest amendments and input voltage range 140 - 300 V, AC, frequency 50 - 60 Hz ,P.F should be more than 0.9 with Total Harmonic Distortion THD(I) less than 15% ,cool white colour and lamp starting time should not be more than 10 second including 10 KV surge protection in built or external. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300 V, AC. Driver should also have double phase protection, no load , open circuit and short circuit protection .LED light fitting should be suitable for ambient temperature from -10 degree Centigrade to 50 degree Centigrade and humidity level 10% to 90 % RH. Covers should be polycarbonate/toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficiency of LED luminaries system shall be more than 100 lumens per watt and must be certified by the LM-79 test report and including connection for street light from pole box with 1.5 Sqmm, 3 core PVC insulated stranded copper conductor FRLSH cable, 1100 Volts grade ISI marked including addition / alteration in bracket (if required) for fixing light fitting complete all as specified and directed by Engineer-in- charge.Make : Havells Cat Part No.:- LHETAVU7PA7J030/Crompton Cat Part TRP-415-30-57-SL-LM-NBK/Wipro Cat Part D912065 or equivalent cat part of Make as specified in Appendix "A".

S&F flush mounting factory made SPN DB 4 way, 240 Volt, Double door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.

S&F as in repair flush mounting factory made SPN DB 12 way, 240 Volt, Double door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. Make :Legrand/L&T/Schneider or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made SPN DB 8 way(concealed flush to wall or as directed), 240 Volt, Double door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. Make :Legrand Ekinox cat part No 5076 11/Havells Model STNDx cat part DHDESHCDOW08/Schneider Easy9 cat part EZ9END08 or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made VTPN DB 4 way, 415 Volt, Double door, IP-43 protection, IK-09 with metal door with 160 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. Make :Legrand/L&T/Schneider or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made TPN DB 4 way, 415 Volt, Double door, IP-43 protection, IK-09 with metal door with 160 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. Make :Legrand/L&T/Schneider or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/L&T/Schneider or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair MCB 40-63 Amps, Single Pole & neutral 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Engineer-in-charge. Make :Legrand/L&T/Schneider or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F MCB 40-100 Amps, four pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/L&T/Schneider or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F in replacement MCCB 4 Pole 125 Amps, thermal magnetic release having, breaking capacity 16 KA, 415 Volt in the existing feeder pillar box including any addition / alteration to the panel to accommodate the new MCCB & making connections with 25x3 mm copper strip as required from main bus bars, making necessary welding work, metal work for fixing base plate etc and connections complete all as specified and as directed by Engineer-in-Charge. Make :Legrand/L&T/Schneider or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

Supply and fixing LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80

S&F in replacement Sub main wiring complete with 2 single core 6 Sqmm (Nominal area) multi stranded copper conductor PVC insulated unsheathed cable FRLSH drawn in and including heavy duty PVC conduit ISI marked not less than 25mm dia concealed including single core multistranded copper conductor 6 Sqmm size cable as earth continuous wire drawn in same conduit complete all as specified and directed by Engineer-in- charge Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length.Make of Cable: Havells/Finolex/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after. Make of Conduit :Supreme/AKG/Finolex or equivalent in Techno commercial makes mentioned in Appendix 'A'

S&F as in repair street light bracket made out of 32mm dia GI pipe light grade 1.20m long , bent to shape at 120 degree angle from vertical fixed along pole with and dirlling holes including required number of clamp made out of Flat iron 25mm x 6mm with nuts, bolts ,washers etc. duly painted with two coats of aluminium paint including any addition / alteration (if required) for fixing street light complete all as specified and as directed by Engineer-in-charge.

M&L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected to galvanized iron strip 32mm x 6mm thick as earth lead by means of bolts, nuts and washers of galvanised iron or steel and thimbles and other end of the earth strip connected to earthing test point/equipment and protected by galvanised iron pipe light grade 40mm dia upto earthing test point/equipment fixed with required number of mild steel clamp made out of 25mm x 3mm flat iron and perforated water pipe 20mm dia GI medium grade of length 2.25 metre and top with socket & plug and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in cement concrete (1:2:4) type B-1 and 40mmthick pre-cast RCC (1:2:4) type B-0 cover with 40mm x 40mm x 3mm MS angle iron frame, excavation & earth work . complete all as specified and directed by Engr-in-charge. Notes :- (i) GI strip upto earth test point/equipment is included in this item. (ii) Outer edge of earth pit chamber shall be 1.5 metre away from the outer edge of PCC chamber. (iii) Minimum weight of reinforcement shall be 1 kg for each earth pit cover Note :- Old unserviceable material retrieved from above mentioned all items shall be deposited in store yard of subdivision by the contractor at his own arrangement. Noting extra shall be paid on this account.

SRI SAI CONSTRUCTION COMPANY (BID ID -3491152)