Proposed Construction of 60 Bedded State Mental Hospital at Imphal (Phase I).

Amount

FOUNDATION:

Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete pile of grade M-25 of specific diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoeand the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top shoe to the bottom of pile cap)

450 mm dia piles

Dismantling of Reinforced concrete pile head complete as per drawing and technical specification

Cement Concrete for reinforced concrete in pile cap complete as per drawing and technical specification .

B) RCC Grade M25

EARTHWORK:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5M including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50M (a) All kinds of soil.

Filling available excavated earth ( excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming & watering lead upto 50 m and lift upto 1.5 m

Filling in plinth with sandy soil under floors including watering, ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering (a) 1:3:6(1 cement : 3 coarse sand : 6graded stone aggregate 40 mm nominal size )

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering (a) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size )

RE-INFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level:

(a) RCC Grade M30

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajas, lintels, bands, plain window sills, staircases and spiral staircases upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with

(a) RCC Grade M30

Reinforced cement concrete work in walls (any thickness) i/c attached pillasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level but excluding the cost of centering and shuttering and reinforcement:

(a) RCC Grade M30

STEEL REINFORCEMENT:

Steel reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete.

(a) Thermo-Mechanically Treated bars

FORM WORKS:

Providing form work i/c centering & shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4m and removal of the same for in-situ reinforced concrete and plain concrete work in:

a). Foundation, footing, bases of column etc and mass concrete.

b). Column, pillar, posts and struts (square rectangle or polygon in plain).

c). Lintels, beams , plinth beams,girders,bresummer and cantilever with water proof ply 12 mm thick

d). suspended floor,roofs landing balconies ans access platform with water proof ply 12 mm thick

Providing and laying damp proof course 50mm thick with cement concrete1:2:4 (1cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)

BRICKWORKS:

Brick work with 1ST class burnt clay F.P.S(non modular) bricks in foundation & plinth in cement mortar 1 : 4 (1cement :4 coarse sand).

Half brick masonrywith 1ST class burnt clay F.P.S(non modular) bricks in foundation & plinth in cement mortar 1 : 3 (1cement :3coarse sand).

ALUMINIUM WORK:

Providing and fixing Aluminium doors,windows and ventilators shutters and pastition etc. with EPDM rubber or neoprene gasket etc complete as per architectural drawings and directions of the engineer in charge(Cost of aluminium snap beadig shall be paid in basic item) with floating glass panes of 4 mm thickness

FLOORING:

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Size of Tile 600 x 600 mm

Granite stone slab flooring over 20 mm ( average ) thick base of cement mortar 1 : 6 ( 1 cement: 6 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete with

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

STEEL WORKS:

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffering, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-Charge, (for payment purpose only weight of the stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.

In grating, frames, guard bar, railing, brackets, gates and similar works.

ROOFING & CEILING:

Providing and fixing false ceiling at all height including providing and fixing of frames work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm ( both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x25x0.55 mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.I channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having cleats of 10.5 mm at 450 mm centre to centre, shall befixed in a direction perpendicular to G.I intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I wire at every junction , including fixing perimeter channels 0.5mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre , with 25 mm long drive - all screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers cocering up to 150 mm on both sides of joint and two coats of primer suitable for both , all as per manufacture's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeters channels suitably fixed, all complete as per drawings and specification an ddirection of the Engineer in charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

FINISHING:

15mm cement plaster 1:3 (1 cement : 3 coarse sand)

12mm cement plaster 1:3 (1 cement : 3 coarse sand ) finished with a floating coat of neat cement .

Providing and applying plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with (two or more coats) with oil bound washable distemper of approved quality on new works i/c priming coat to give an even shade.

Finishing walls with water proofing cement paint of approved quality on new work (three or more coats) to give an even shade.

Making plinth protection 50 mm cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggrt. of 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm niminal size well rammed ans consolidated and grouted with fine sand including finishing the top smooth.

INTERNAL ELECTRIFICATION & INSTALLATION:

Wiring for light/Fan point/Exhaust Fan point/Call bell point with 1.5mm²FRPVC insulated copper conductor single core cable in surface/recessed steel conduit with modular type switch modular plate,suitable G.I.box and earthing the point with 1.5mm²FRPVC insulated copper conductor single core cable etc.as required.

Suitable size GI box with modular plate and in front on surface or in recess i/c p/f 6 pin 16/15 amp modular socket outlet 15/16 amp modular switch, connection painting etc as required

s/f suitable size G.I box with modular plate and cover infront on surface or recess i/c p/f 3pin 5/6 amp modular socket outlet 5/6 amp modular switch connection painting etc as reqd.

(1.7) Wiring for circuit/sub-main wiring along with earth wire with the (following size of ) FRPVC insulated copper conductor single core cable in surface/recessed steel conduit etc. as reqd.

1)2x1.5mm²+1x1.5mm² Earthwire

2)2x2.5mm²+1x2.5mm² Earthwire

3)2x4mm²+1x4mm² Earthwire

4)2x6mm²+1x6mm² Earthwire

5)2x10mm²+1x10mm²Earthwire

6)2x16mm²+1x16mm²Earthwire

(1.87) S/F (following way) single pole and neutral, sheet steel MCCB DB 240v on surface/recessed complete with tinned copper busbar, neutral busbar, earthbar, dinbar, hinged front acrylie cover for the MCCB knobs datacable grand plate, enter connection, phosphatised and power painted including earthing etc. as required (but without MCB/RCCB/isolator)

(1.107) S/F 5amp to 32 amp rating 230V “B” series for lighting and other purposes, load of (following poles) in the existing MCB DB complete with connection, testing and commissioning etc. as required.

(2) Single pole and neutral

(1.109) S/F (following rating) double pole 240 V isolator in the existing MCB DB complete with connection testing and commissioning as required.

(1.84) P/F (following capacity TP&N) dis-connector fuse switch unit inside the exiting cubicle panel board with I.S.I mark HRC fuses i/c drilling holes in the cubicle panel board making connection as reqd.

(2) 400 Amp TP&N

(2) 200 Amp TP & N

P/F 400Amp TPN stand ground on load on load change own switch (compact design) 415/500v including connection to as required.

S/F Busbar chamber with 4 strips copper busbar of length 600mm suitable for 2oo amps capacity complete with all accessories i/c connection earthing the body as required.

(8.01) S/F 48” sweep (1200mm)a.c ceiling fan complete with down rod, canopy, 3 Blades but without regulator etc. as reqd. (Havells or similar 5 star)

305mm sweep exhaust fan complete with all accessories connection etc as required

1.62) S/F stepped type electronic fan regulator on the modular plate switch box i/c connection but excluding modular plate as reqd.

P/F swing wall fan

(1.71) S/F brass batten holder i/c connection etc. as reqd.

LED white lamp 18w

S/F 1,5 ton capacity split type air conditioner(Voltas/Hitachi, 3star)

S/F 25 amp Air conditioner power plug point i/c 4modules metal box on surface or in recess 4 module cover plate and cover in front 25 amp moduler starter 25 amp moduler socket outlet and 25 amp plug i/c connection etc as reqd.

S/F recess mounting LED down lighter BGSL 0301WH 220225 Cast alluminium housing fixed with collinated lens 3x1W white lens mounted on MCPCB extruded alluminium heat sink , spring loaded mounting clips ,complete with connection etc as reqd.

p/f lighting conductor finial made of 25mm dia 300mm long copper tube having single prong at top with 85mm dia 3mm thick copper plate i/c holes etc. Complete as reqd

p/f copper tape in horizontal run p/f copper tape 2ommx3mm thick on parapet or surface of wall for lightning conductor as reqd(for horizontal run)

p/f copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd(for vertical run)

(3.05) Earthing with copper earth plate 600 mmx 600mmx6mm thick i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) as reqd.

(3.06) Extra for using Salt & Charcoal for copper plate with electrode as reqd.

Earth connection from earth electrod with 4mm dia in 15mm GI pipe as required 5m (4no)

Fabrication of controlled panel board by 16 guage steels sheet along with componets mounting making strip wiring auxillary components wiring all over the panel i/c fixing charge painting etc as reqd. 25(3no)

WATER SUPPLY & SANITARY INSTALLATION.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

External work- 50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

Internal work- 32mm nominal outer dia Pipes

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-

(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 32 mm dia

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. Pan

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.(a) 15 mm nominal dia

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing toilet paper holder: C.P. brass

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing UPVC soil, waste, rain water and vent pipes including all requisite fittings, jointing of pipes & fittings with solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge. a).110mm dia

b).75mm dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall

Internal work - Exposed on wall

25 mm diameters

32 mm diameter

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.external work - Exposed on wall

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc.complete : 50 to 80 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. : 15 mm Nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

25 mm nominal bore.

Providing and fixing Water Storage Tanks with 400 mm diameter nominal base G.I. overflow tube 25 mm nominal G.I. inlet and 15 mm nominal G.I. outlet tube i/c hoisting a height of 10 m above ground level. a).2000 litres net capacity storage tanks

Supply and fixing self priming single phase (TEXMO or similar brand ) of 1HP water pump of approved quality

WATER RESERVOIR

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a) All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m..

Boulder with minimum size of 300mm for pitching at Site

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - a) 1:4:8 (1 Cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level : a) (RCC M25)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. above plinth level upto floor five level excluding cost of centering,shuttering, finishing and reinforcement :(RCC M25)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases above plinth level upto floor five level, excluding the cost of centering,shuttering, finishing and reinforcement with RCC M25

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.Thermo-Mechanically Treated bars

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : a) Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.a),40mm thick with 20mm nominal size stone aggregate.

SEPTIK TANK

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Boulder with minimum size of 300mm for pitching at Site

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering --All work upto plinth level:a).1:4:8 (1 cement : 4 coarse sand :8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering --All work upto plinth level: 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. above plinth level upto floor five level excluding cost of centering,shuttering, finishing and reinforcement : (a).1:1.5:3 (1 Cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size).Upto floor five level

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level .a) Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for:

(a).Foundation, footing, bases of columns etc. and mass concrete.

b).Suspended floors, roofs, landings, balconies and access platform.

c).Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Providing and fixing C.I. Cover frame (for manhole and chambers).a).600 mm x 450 mm (heavy duty)

LAND DEVELOPMENT

Construction of embankment with material obtained from borrow pits (Construction of embankment with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2)

LAND SCAPING

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m, as directed by the Engineer-in- Charge. All kinds of soil.

1:5:10 (1 Cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409)

PCC M-20 for Kerb Cast-in- situ

Supplying at Site Well Decayed Farm Yard Manure ( Supply at Site of work well decayed farm yard manure, from any available source, approved by the enineer in charge including screening and stacking)

P/M of Flowering Plants and Shrubs. (a) Maintenance of Flowering Plants and Shrubs in central Verge for one Year.

Planting and Maintaining of Permanent Hedges. (ii) Maintenance of Hedge for one year.

Tree Guard with MS Angle Iron and Steel Wire (Providing and fixing tree guard 0.60 meter square, 2.00 meter high fabricated with MS angle iron 30 x30 x3 mm, MS iron 25 x 3mm and steel wire 3mm dia welded and fabricated as per design in two halves bolted together.).

Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 10 m high spaced 40 m apart, 1.8 m overhang on both sides if fixed in the median and on one side if fixed on the footpath, fitted with sodium vapour lamp and fixed firmly in concrete foundation..)

For fixing in Footpath

FIRE FIGHTING

FIRE HYDRANT & SPRINKLER SYSTEM

Supply of External and internal fire hydrant Mild Steel pipe as per IS 1239 Medium & B Class with all fittings, such as bends, elbows, flanges, tees, unions, coupling, expander/redducers, gaskets, nut bolts washers etc.

150 MM dia

100 MM dia

80 MM dia

50 MM dia

40 MM dia

25 MM dia

Supply of Pendent type Sprinkler.

Supply of 63 MM dia 15 mtr. long RRL hose pipe with Male & Female Coupling.

Supply of 63 MM Short Branch pipe fitted with 25MM Nozzle .

Supply of 63 mm dia ISI marked Hydrant valve for Internal/ External landing.

Supply of First Aid Swiming Hose reel drum with 20MM Thermo plast water hose and nozzle.

Supply of Double door Glass fronted hose box cabinet suitable for Two hoses and one branch pipe nozzle, with locking arrangement painted red outside and white inside

Supply of Cast iron Butterfly valve 80 MM dia of PN 1.0 rating complete with volt, nuts, compansion flanges.

Supply of Cast iron Butterfly valve 100 MM dia of PN 1.0 rating complete with volt, nuts, compansion flanges.

Supply of Cast iron Butterfly valve 150 MM dia of PN 1.0 rating complete with volt, nuts, compansion flanges.

Supply of C.I. Non Return Valves Single Plate 80 MM dia PN 1.0 including washer, nut bolt, 1.5 mm thick compressed asbestos gasket companion flanges

Supply of C.I. Non Return Valves Single Plate 100 MM dia PN 1.0 including washer, nut bolt, 1.5 mm thick compressed asbestos gasket companion flanges

Supply of C.I. Non Return Valves Single Plate 150 MM dia PN 1.0 including washer, nut bolt, 1.5 mm thick compressed asbestos gasket companion flanges

Stainless steel corrugated 1500 MM flexible pipe(hose) for dropping sprinklers below false ceiling, pipe shall be 16 bar pressure rating ,25/15 mm dia with union / reducer collar, clamps etc. as required.

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type 25 mm dia.

Supply, erection, testing & commissioning of Air Vessel made of 250mm dia, 8mm thick ms sheet, 1200 mm height with air release valve on top and flanged connection to riser , drain arrangement with 25mm dia,with all accesseraries.

FIRE ALARM SYSTEM

Supply,installation, testing and commissioning of intelligent Addressable ionisation type photoelectric & Smoke Detectors with dual chamber solid state design, indicating lamp, mounting base etc. as per detailed specification.

Supplying, installing, testing and commissioning of intelligent Addressible Manual pull station with necessary accessories.etc.

Supplying, installing, testing and commissioning of intelligent Addressible Hooter with necessary accessories etc.

Supplying, installing, testing and commissioning of 2 core x 1.5 sq. mm, Armoured cables FRLS type confirming to IS standards and specifications.

Fire Alarm Control panel with Lead acid battery back up for 8 hours normal operation and 15 minutes alarm operation. The control panel, battery charger etc, shall be as per requirement. 4 Loop Panel

HAND APPLIANCES

Supply of 4.5 KG. Capacity CO2 Type Fire Extinguishers.

VEHICLE PARKING

Supply of 09 Ltr. Capacity AFFF Type Fire Extinguishers

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level:

(a)1:4:8 ( 1 Cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

(b)1:3:6 ( 1 Cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, etc. for mass concrete.

Land Development

Excavation in soil by manual means. (Excavation for roadway in soil using manual means including loading in truck for carrying of cut earth to embankment site with all lifts and lead upto 1000 meters.

EXTERNAL ELECTRIFICATION

(18) 9m long steel tubuler pole (410 SP-14)

(7.01) Erection of steel tubular pole of length not less than 8m but not exceeding 10ms in cement concrete 1:3:6 (1 cement :3 coarse sand : 6graded stone aggregate 40mm nominal size) foundation i/c excation and refiling etc as required.

(1.7) wiring for circuit/ submain wiring along with earth wire with the (following size of) FRPVC insulated copper conductor single core cable in surface/recessed steel conduit etc as reqd.

3) 2x4.0mm²+ 1x4.0mm² Earth wire

(3) S/F2.5 m long G.I bracket and pipe for fixing street lamp and lamp post.

(1.87) S/F (following way) single pole and neutral, sheet steel MCCB DB 240 v on surface /recessed complete with tinned copper busbar, neutral busbar, earthbar, dinbar, hinged front acrylie cover for the MCCB knobs datacable grand plate, enter connnection, phosphatised and power painted including earthing etc, as required ( but without MCB/RCCB/ isolator)

(1.107) S/F 5amp to 32 amp rating 230 V "B" series for lighting and other purposes, load of (following poles)in the existing MCB DB complete with connection, testing and commissioning etc as required.

(2) Single pole and neutral

(1.109) S/F (following rating) double pole 240 V isolator in the existing MCB DB complete with connection testing and commissioning as required.

P/F 50w street Lamp (Panasonic,Bajaj or Philips)

PUMP HOUSE AND GENERATOR ROOM

EARTHWORK:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5M including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50M (a) All kinds of soil.

Filling available excavated earth ( excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming & watering lead upto 50 m and lift upto 1.5 m

Filling in plinth with sandy soil under floors including watering, ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering (a) 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size )

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering (a) 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size )

RE-INFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level:

(a) 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajas, lintels, bands, plain window sills, staircases and spiral staircases upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with

(a) 1:1.5:3 ( 1 cement :1.5 coarse sand :3 graded stone aggregate 20 mm nominal size)

STEEL REINFORCEMENT:

Steel reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete.

(a) Thermo-Mechanically Treated bars

FORM WORKS:

Providing form work i/c centering & shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4m and removal of the same for in-situ reinforced concrete and plain concrete work in:

(a) Foundation footings, bases of columns etc. and mass concrete.

(b) sides and soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth

BRICKWORKS:

Local first class brick in foundation and plinth in cement mortar 1:4 (1 cement :4 coarse sand)

STEEL WORKS:

Steel work in built up tubular trusses includidng cutting, hoising, fixing in position and applying a coat ofapproved steel primer red oxide zinc chrome primer (conforming to IS :2079 ) welded and bolted inclusing special shape washer etc. complete. Electrical resistance welded tube (Conforming to IS:1611-1979).

ROOFING & CEILING:S:

Prividing corrugated G.S. sheet roffing including vertical/curve surface fixed…....

(a) 0.63 mm thick with Zinc coated…..

PAVERBLOCK:

P/L Flooring complete as per draawing and Technical Specifications laid over cement concrete bedding. (a) C/C blocks Grade M15 including 100mm thick bedding.

FINISHING:

15 mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement.

Rolling shutters of 80x1.2mm laths

Rolling shutters of 80x1.2mm laths

INTERNAL ELECTRIFICATION & INSTALLATION

Wiring for light/Fan point/Exhaust Fan point/Call bell point with 1.5mm²FRPVC insulated copper conductor single core cable in surface/recessed steel conduit with modular type switch modular plate,suitable G.I.box and earthing the point with 1.5mm²FRPVC insulated copper conductor single core cable etc.as required.

Suitable size GI box with modular plate and in front on surface or in recess i/c p/f 6 pin 16/15 amp modular socket outlet 15/16 amp modular switch, connection painting etc as required.

(1.7) Wiring for circuit/sub-main wiring along with earth wire with the (following size of ) FRPVC insulated copper conductor single core cable in surface/recessed steel conduit etc. as reqd.

1) 2x1.5mm² +1x1.5mm² Earthwire

3)2x4mm²+1x4mm² Earthwire

(1.109) S/F (following rating) double pole 240 V isolator in the existing MCB DB complete with connection testing and commissioning as required.

(1.71) S/F brass batten holder i/c connection etc. as reqd.

LED white lamp 18w

P/F 2hp Electric water pump

COMPOUND FENCING

FOUNDATION:

Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete pile of grade M-25 of specific diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoeand the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top shoe to the bottom of pile cap)

450 mm dia piles

Dismantling of Reinforced concrete pile head complete as per drawing and technical specification

EarthWork

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a) All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:4:8 ( 1 Cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level : 1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. up to floor five level excluding cost of centering,shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases above plinth level upto floor five level, excluding the cost of centering,shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

STEEL REINFORCEMENT

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level and above plinth. Thermo-Mechanically Treated bars

FORM WORKSv

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, etc. for mass concrete.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

BrickWorks

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 4 (1 cement : 4 coarse sand)

STEEL WORKS:

Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying coat of approved steel primer all complete.

Finishing

12 mm cement plaster of mix: 1:4 (1 cement : 4 fine sand)

15 mm cement plaster on rough side of single or half brick wall of mix:-1:4 (1 cement : 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Supplying and fixing galvanised steel barbed wire.weighing 9.38kg/100 m straining and fixing to any type of standard rails straining bolts i/c securing with and provision of galvanised mild steel wire, staples or steel pins etc as directed

WATER DRAIN

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a) All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Centering and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:4:8 ( 1 Cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - 1:3:6 ( 1 Cement: 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

MAIN GATE

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a) All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sandy soil under floors including, watering,ramming consolidating and dressing complete.

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering in a).1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

DAMP-PROOF COURSE

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work @1 kg per 50 kg of cement.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per sqm on damp-proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in Kerosene oil.

RE-INFORCED CEMENT CONCRETE WORK

Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering,shuttering,finishing and reinforcement-All work up to plinth level:

1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete works in beams,suspended floors,roofs having slope up to 15˚ landing,balconies,shelves,chajjas,lintels,bands,plain window sills,staircases and spiral stair cases up to floor five level excluding the cost of centering,shuttering,finishing and reinforcement,with

1:1.5:3(1 cement :1.5 coarse sand:3 graded stone aggregate 20mm nominal size)

Reinforced cement conerete work in walls(any thickness),including attached pilasters,buttresses,plinth and stringcourses, fillets, column, pillars, piers, abutments, posts and struts etc.up to floor level excluding cost of centering,shuttering,finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

STEEL REINFORCEMENT

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.(Thermo-Mechanically Treated bars

BRICKWORK

Brick work with Ist class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

HALF BRICK MASONRY

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 4 (1 cement : 4 coarse sand)

FORMWORK

Centering and shuttering including strutting, propping etc. and removal of form for:

(a)Foundations, footings, bases of columns, etc. for mass concrete.

(b).Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12mm thick

(c) Columns, Pillars, Piers, Abutments, Posts and Struts.

(d) Lintels, beams, plinth beams, girders, bressumers and cantilevers.

STEEL WORK

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.

Steel work welded in built up sections, framed work in cutting, hoisting, fitting in position & priming coat of red lead paint. (a) In gratings, framed guard bars, ladders, railings, brackets and similar works.

Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying coat of approved steel primer all complete.

WOOD WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately : Local best quality TEAK wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Local best quality Teak Wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250x10 mm

Providing and fixing M.S.Pressed Butt hinges bright finished with necessary screws etc.125 x 65 x3 mm

Providing and fixing bright finished brass handles with screws etc. complete :125 mm

FLOORING

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and laying Vitrified tiles in different sizes (thickness to be speciied by manufacturer ) ,with water absorption less than 0.08% and conforming to IS :15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc.,complete.Size of Tile -600 x600mm.

FINISHING

12 mm cement plaster of mix : 1:4 (1 cement : 4 fine sand)

15 mm cement plaster on rough side of single or half brick wall of mix:-1:4 (1 cement : 4 fine sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75mm dia.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs,screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1 cement: 4 coarse sand) and making good the wall etc. complete.. 75 mm dia.

CEMENT PAINTING - ORDINARY

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coat :-With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat :- With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works:-

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.h

WATER SUPPLY & SANITARY INSTALLATION

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 metres in width as well as 10 sqm on plan i/c disposal of excavated earth lead upto 50 m and lift upto 1.5 m disposal soil to be levelled and neatly dressed in

Filling available excavated earth in trences,plinth, sides of foundations, etc in layers noy exceedinfg 20cm in depth,consolidating each de[posited layer by rammring and watering, lead upto 50m and lift upto 1.5m

Providing and laying in position cement concrete of specified grade excluding the cost centering and shuttering- All work upto plinth level.

1:4:8 (1 cement :4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost centering shuttering- All work upto plinth level.Reinforced cement concrete work in foundation footings, bases of columns etc. and mass concrete, excluding cost of centering, shuttering and reinforcement,

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams,suspended floors, roofs having slope upto 15 degree landings, shelves & their supports balconies,chajjas, lintels, bands, plain window sill, stair cases and spiral stair cases upto floor 5 level excluding the cost of centering , shuttering finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse:3 graded stone aggregate 20mm nominal size).

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundation, footings, bases of columns etc. and mass concrete.

Flat surface……..

i) Edges of slab and breaks in floor walls

under 20 cm wide

Reinforcementfor R.C.C work including straightening ,cutting, bending,placing in position and binding all complete.

Thermo-Mechanically Treated bars.

20 mm cement plaster 1:3 (1cement :3 coarse sand) finished with afloating coat of neat cement

Providing and fixing WATER STORAGE TANKS (Sintex) with 400 mm diameter nominal base G.I. overflow tube 25 mm nominal G.I. inlet and 15 mm nominal G.I. outlet tube i/c hoisting a height of 10 m above ground level.

1000 litres net capacity storage tanks

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm with flush pipe and integrated type foot rests

P/F urinal basin of white glazed earthen ware (Indian make) with 5 litres C.I. Automatic flushing cistern with fitting R.S. or C.I. Brackets,standard size, flush pipe spreader with brass union G.I. Clamp complete, including painting of cistern and fitting cutting and making good the wall and floors.

a) Flat back Urinal

Providing and Fixing wash basin of white glazed earthen ware (Indian make) with R.S. or C.I. brackets painted white 1 central 12.5 mm C.P. brass pillar tapes, 32 mm rubber plugs and C.P. brass chain 32 mm C.P. brass waist-of standard pattern 32 mm diameter M.I. or C.P. brass traps and unions complete i/c cutting and making good the walls (Indian fittings).

P/F kitchen sink white glazed vitreous china (Indian make) with R.S. or C.I. Brackets painted white, a pair of 12.5 mm C.P. brass pillar taps, 323 rubber plugs and C.P. brass chain 32 mm C.P. brass waste of standard pattern, 32 mm dia M.I. Or C.P. brass traps and unions complete i/c cutting and making good the walls indian fittings.

Providing and fixing 600 x 20 mm SONA C.P. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screws (Hook type SONA)

Providing and fixing 600 x 450 mm bevelled edge mirror of Indian make superior glass (of approved quality) quality complete with asbestos sheet ground, fixed to wooden cleat with C.P. brass screws and washers.

Providing and fixing in position 2.5 mm diameter mosquito proof coupling of approved Municipal design.

Centre Hole Mixer H.N. Deluxe.

Providing and fixing M.I. union fisher

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms.

Providing and fixing a pair of white glazed earthen foot rest of standard pattern for Indian type W.C. pan.

Providing and fixing soap container of glass with C.P. lid and brackets fixed to wooden cleats with C.P. brass screws.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

White Vitreous China Angle back wash basin size 600 x 480 mm with single 15 mm C.P. brass pillar tap

Providing and fixing lead caulked joints to 100 mm HCI pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

100 mm nominal outer dia Pipes

P/F 50 mm dia normal guage polythene pipes of approved quality complete with special flange compression type fittings (of approved make) including trenching and refilling etc (external works).

P/F brass stop cock of superior quality

Providing and fixing Polythene-Aluminium- Propylene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. with carbon black having thermal stability for hot & cold water supply,capable to with stand temperature up to 80 degree centrigate, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 m spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of Engineer in charge. Concealed work, i/c cutting chases and making good the wall etc.)

(a) 1216 (16 mm OD) pipe

(b) 1620 (20 mm OD) pipe

(c) 2025 (25 mm OD) pipe

(d) 2532 (32 mm OD) pipe

Providing and fixing Chlorinated Polyviny Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fitting with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge ( External works etc.)

Making connection of GI distribution branch with GI main 25 mm to 40 mm diameter by providing & fixing Tees i/c cutting and threading the pipe etc complete.

Providing and fixing C.P. bib cock of superior quality.

(a) 20 mm diameter

Providing and fixing brass stop cock of superior quality.

(a)15 mm diameter (Delux Sona)

Providing and fixing non-return value of superior quality. (32mm diameter)

INTERNAL ELECTRIFICATION & INSTALLATION.

Wiring for light/Fan point/Exhaust Fan point/Call bell point with 1.5mm²FRPVC insulated copper conductor single core cable in surface/recessed steel conduit with modular type switch modular plate,suitable G.I.box and earthing the point with 1.5mm²FRPVC insulated copper conductor single core cable etc.as required.

Suitable size GI box with modular plate and in front on surface or in recess i/c p/f 6 pin 16/15 amp modular socket outlet 15/16 amp modular switch, connection painting etc as required

s/f suitable size G.I box with modular plate and cover infront on surface or recess i/c p/f 3pin 5/6 amp modular socket outlet 5/6 amp modular switch connection painting etc as regd.

(1.7) Wiring for circuit/sub-main wiring along with earth wire with the (following size of ) FRPVC insulated copper conductor single core cable in surface/recessed steel conduit etc. as reqd.

2) 2x1.5mm² +1x1.5mm² Earthwire

3)2x4mm²+1x4mm² Earthwire

(1.87) S/F (following way) single pole and neutral, sheet steel MCCB DB 240v on surface/recessed complete with tinned copper busbar, neutral busbar, earthbar, dinbar, hinged front acrylie cover for the MCCB knobs datacable grand plate, enter connection, phosphatised and power painted including earthing etc. as required (but without MCB/RCCB/isolator)

(1.107) S/F 5amp to 32 amp rating 230V “B” series for lighting and other purposes, load of (following poles) in the existing MCB DB complete with connection, testing and commissioning etc. as required.

(2) Single pole and neutral

(1.109) S/F (following rating) double pole 240 V isolator in the existing MCB DB complete with connection testing and commissioning as required.

(1.84) P/F (following capacity TP&N) dis-connector fuse switch unit inside the exiting cubicle panel board with I.S.I mark HRC fuses i/c drilling holes in the cubicle panel board making connection as regd.

(3) 100 Amp TP&N

(8.01) S/F 48” sweep (1200mm)a.c ceiling fan complete with down rod, canopy, 3 Blades but without regulator etc. as reqd. (Havells or similar 5 star)

1.62) S/F stepped type electronic fan regulator on the modular plate switch box i/c connection but excluding modular plate as reqd.

(8.52) S/F recess mounting LED down lighter BGSL 0301WH 220225 Cast alluminium housing, fixed with collinated lens 3X1W white Led mounted on MCPCB, extruded alluminium heat sink, spring loaded mounting clips, complete with connection etc. as reqd.

M/s Acura Ventures

M/s G.Thaninjao R.Naga and Sons