CONSTRUCTION OF RESIDENTIAL COLONY AT MADHUBAN DULIAJAN

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 1:2:4 (1 Cement : 2 coarse sand derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (Zone III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:3 (1 cement : 3 coarse sand)

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately) Area of slab over 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : 40 mm thick

Stone work (machine cut edges Veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shallbe paid for separately). 25 mm thick

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approvedshop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Float glass panes 4 mm thick glass pane (weight not less than 10 kg/sqm)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 5.5 mm thick glass panes (weight not less than 12.50 kg/sqm)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm coir veneer board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing chromium plated brass curtain rods having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 25 mm dia.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete : 125x90x4.00 mm

Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete : 150mm

Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors, (weighting not less than 450 gms)

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 200x10 mm

Providing and fixing bright finished brass night latch of approved quality including necessary screws etc. complete.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 40mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing chromium plated brass night latch of approved quality including necessary screws etc. complete.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 65 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing non load bearing fixed frame for fire resistant glazed Partition for 120 minutes Fire Rating, made out to a profile of dimension 60mm x 70 mm of 1.6 mm thick galvanised steel sheet as per test evidence suitable for fixing fire rated glass for 120 minutes of both integrity & radiation control (EW120) & minimum 20 minutes of insulation (EI20).The profile has to be fixed to the supporting construction by means of anchor fasteners of size M10 x 80, every 150 mm from the edges and every 500 mm (approx) c/c. Linear measurement of frame shall be measured for payment. The frame shall be filled with mineral wool insulation of density min 96kg/ m³ and finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer - in- charge.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube.

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15 x 3mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides.

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 1:6 (1cement : 6 coarse sand)

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m²

supplying and fixing colur coated 0.45 mm BMT(base metal thickness)and 0.53 mm Total Paint Thickness Lysaght KLIP-LOK concealed fix profile of 700mm effective cover width ,with 4 major deep corrugation 43mm deep rib spaced at 230 mm C/C alongwith micro stiffener perpendicular to ribs for strength.The Male and Female rib will have anti-capilliary groove . The steel sheet will have min. yield strength of 550 MPa , metallic coated with aluminium zinc alloy ( ie Zincalume ) , AZ150 ( min 150 gsm/m2 total on both sides), conforming to as 1397/ASTMA 792M/IS15961, pre-painted with Super Durable Polyster Colorbond XRW with higher SRI value ( Thermatech Technology ) and uses only inorganic pigments in paint system conforming to AS/NZS 2728type 4/IS15965 class 3 of Tata Blue Scope Steel make or as appvd by Consultant.

supplying and fixing colur coated 0.45 mm BMT(base metal thickness)and 0.53 mm Total Paint Thickness Lysaght KLIP-LOK concealed fix profile of 700mm effective cover width ,with 4 major deep corrugation 43mm deep rib spaced at 230 mm C/C alongwith micro stiffener perpendicular to ribs for strength.The Male and Female rib will have anti-capilliary groove . The steel sheet will have min. yield strength of 550 MPa , metallic coated with aluminium zinc alloy ( ie Zincalume ) , AZ150 ( min 150 gsm/m2 total on both sides), conforming to as 1397/ASTMA 792M/IS15961, pre-painted with Super Durable Polyster Colorbond XRW with higher SRI value ( Thermatech Technology ) and uses only inorganic pigments in paint system conforming to AS/NZS 2728type 4/IS15965 class 3 of Tata Blue Scope Steel make or as appvd by Consultant. Flashing in COLORBOND XRW 0.45 BMT (0.53 TPT 0 mm to 610 mm girth ( Only Ridge & Valley )

supplying and fixing colur coated 0.45 mm BMT(base metal thickness)and 0.53 mm Total Paint Thickness Lysaght KLIP-LOK concealed fix profile of 700mm effective cover width ,with 4 major deep corrugation 43mm deep rib spaced at 230 mm C/C alongwith micro stiffener perpendicular to ribs for strength.The Male and Female rib will have anti-capilliary groove . The steel sheet will have min. yield strength of 550 MPa , metallic coated with aluminium zinc alloy ( ie Zincalume ) , AZ150 ( min 150 gsm/m2 total on both sides), conforming to as 1397/ASTMA 792M/IS15961, pre-painted with Super Durable Polyster Colorbond XRW with higher SRI value ( Thermatech Technology ) and uses only inorganic pigments in paint system conforming to AS/NZS 2728type 4/IS15965 class 3 of Tata Blue Scope Steel make or as appvd by Consultant. Flashing in COLORBOND XRW 0.45 BMT (0.53 TPT KL70 Clips for installing Klip-Lok 700

supplying and fixing colur coated 0.45 mm BMT(base metal thickness)and 0.53 mm Total Paint Thickness Lysaght KLIP-LOK concealed fix profile of 700mm effective cover width ,with 4 major deep corrugation 43mm deep rib spaced at 230 mm C/C alongwith micro stiffener perpendicular to ribs for strength.The Male and Female rib will have anti-capilliary groove . The steel sheet will have min. yield strength of 550 MPa , metallic coated with aluminium zinc alloy ( ie Zincalume ) , AZ150 ( min 150 gsm/m2 total on both sides), conforming to as 1397/ASTMA 792M/IS15961, pre-painted with Super Durable Polyster Colorbond XRW with higher SRI value ( Thermatech Technology ) and uses only inorganic pigments in paint system conforming to AS/NZS 2728type 4/IS15965 class 3 of Tata Blue Scope Steel make or as appvd by Consultant. Flashing in COLORBOND XRW 0.45 BMT (0.53 TPT CLASS 3 Self drilling scew 12-24 x 32 with EPDM Washer for in stalling KL 70 Clips and fixing Klip-Lok 700 at Ridge and Eave end

CLASS 3 Self drilling scew 10-16 x 25 with EPDM Washer FOR FLASHINGs

Aluminium Blind Rivets - Domed Head for flashings.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board.

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix : mix : 1:4 (1 cement: 4 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement: 3 fine sand) : Raised and cut pointing

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including water thinnable priming coat with cement primer.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On wooden work

Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture, over and including a priming of ready mixed zinc chromate yellow primer on new work :150 mm diameter pipes

Painting with aluminium paint of approved brand and manufacture to give an even shade . Two or more coats on new work

Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : 450 mm dia piles

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and laminated on both side by laminate Sheet/PVC foil lamination. The exposed edges shall be sealed with PVC edge beading of same shade and colour. The shutter shall be fire retardent having necessary screw holding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction of Engineer-in-charge.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/black), comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross- T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm.With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia, 50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/ tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer’s specification as per direction of Engineer-in-Charge all complete.With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variationin profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern

Providing and fixing white vitrious china Water Closet squating pan( Indian Type) (b) Orrissa patern WC 580x 440mm

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : Range of four squatting plates with 10 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 225 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing 100 mm s/s grating for gully trap. (as per market rate )

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Circular shape 450 mm dia.

Rectangular shape 1500x450 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729.

75 mm diameter : Sand cast iron S&S pipe as per IS: 1729.

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 75 mm dia pipe

100 mm dia pipe

Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS - 1729

75 mm dia Sand cast iron S&S as per IS -1729

Providing and fixing heel rest sanitary bend 100 mm dia Sand cast iron S&S as per IS - 1729

75 mm dia Sand cast iron S&S as per IS - 1729

Providing and fixing double equal plain junction of required degree. 75x75x75x75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 1729

75x75x75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing sand cast iron S&S off sets as per IS: 1729 76 mm off sets With 100 mm dia pipe

Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 100 mm Sand cast iron S&S as per IS - 1729

75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 100 mm dia SS 304 grade coupling with EPDM rubber gasket

75 mm dia SS 304 grade coupling with EPDM rubber gaske

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 100 mm

Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter : 100 mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms.

Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 25 mm nominal outer dia. Pipes.

32 mm nominal outer dia. Pipes.

50 mm nominal outer dia. Pipes.

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : (as per market price)150 mm diameter

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

supplying and fitting c.p pillar cock best quality as approved (as per market price)15 mm nominal bore.

supplying and fitting c.p bip cock best quality as approved (as per market price)15 mm nominal bore

supplying and fitting c.p stop cock best quality as approved (as per market price)15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing hand shower best quality as approved(as per market rates)

Providing and fixing health faucet including all fittings best quality as approved(as per market rates)

Providing and fixing single liver wall mixer best quality as approved(as per market rate)

Providing and fixing soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 15 mm nominal bore.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Construction of septic tank as per drawing and design complete 50 user

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group-A Upto 3 mtr

Group B- Upto 6 mtr.

Group C- Upto 10 mtr.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia insulated annealed copper conductor, unarmored FRLS PVC telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit conduit along with accessories in surface/ recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.25mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch 25A Single Phase DOL Starter for AC Units

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch 3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch 6 pin 15/16 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch TV antenna socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections modular plate etc. as required.5/6 A switch Bell Push

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required.3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required 4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required 8 Module (125mmX125mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supply of light fixtures/ Fittings as per the details given below including necessary hardware such as clamps,nuts, bolts, nails, screws and suspension chains as required for fixing the fixtures in position as required DOWN LIGHT [DL]- Round LED recess-mounted designer panel with aluminium die cast housing , Wattage-18W, (14W for Emergency Light Points) CCT- 4000 K,

Supply of light fixtures/ Fittings as per the details given below including necessary hardware such as clamps,nuts, bolts, nails, screws and suspension chains as required for fixing the fixtures in position as required PANEL LIGHT [PL] - Ultra Slim LED Panel made from extruded aluminium housing frame (recess / pendant) 2ft x 2ft , Wattage-30W, CCT- 4000 K,

Supply of light fixtures/ Fittings as per the details given below including necessary hardware such as clamps,nuts, bolts, nails, screws and suspension chains as required for fixing the fixtures in position as requiredWall Mounted LIGHT FIXTURE - Wattage-14-18W, CCT- 4000 K,

Supply, Installation, testing and commissioning of Led fixture Surface Mounted 4 Feet with Polycarbonate diffuser with aluminium housing having following technical specifications with all accessories including connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable i/c hanging arrangement with chain and wiring with GI flexible conduit with coupler where ever if required and earthing as required.. (i) Minimum lumen output 4000 lumen (ii) System lumen efficacy ≥ 110 Im/Watt (iii) CCT ≥ 5700, CRI > 80, PF≥ 0.95, THD < 10%, IP 40 (iv) L 70 rated life of 50 K hours (v) in built surge protection device of minimum 2.5 KV.

Supply, Installation, testing & commissioning of Surface type batten LED fitting minimum length 2 Feet with extruded aluminium housing having following technical specifications with all accessories directly on ceiling/wall including connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and earthing etc. as required (i) Minimum lumen output 1000 lumen (ii) System lumen efficacy ≥ 100 Im/Watt (iii) CCT ≥ 6500, CRI > 80, PF≥ 0.95, THD < 20%, IP 40 (iv) L 70 rated life of 50 K hours (v) in built surge protection device of minimum 2.5 KV.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying, Installation, Testing and Commissioning of single phase 300mm Sweep, 900/1400 RPM heavy duty Upto 450 mm sweep propeller type exhaust fan for operation on 220-240 V, 50Hz, AC electricity, in the existing opening including making good the damages and connection with 1.5 sqmm FRLS PVC insulated copper wire including louver shutter complete as required.

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.2 Run of Cable

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-A Upto 3 mtr

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B- Upto 6 mtr.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C- Upto 10 mtr.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A,30KA,FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 125 A,36KA,FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 250 A,36KA,FPMCCB

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 Way, Double Door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 16 way, Docuble Door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . 4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A

Supply, Installation, testing and commissioning of LED street light fitting in pressure die cast aluminium body with glass/PC cover complete with inbuilt driver, accessories fixing on existing pole with having following technical specifications i/c making connection with 1.5 sq mm FRLS PVC insulated copper conductor single core cable and earthing, testing etc as reqd.(i) Minimum lumen output 4500 lumen (ii) System lumen efficacy ≥ 120 Im/Watt (iii) CCT ≥ 5700, CRI > 80, PF ≥ 0.95, THD < 10%, IP 66 (iv) L 70 rated life of 50 K hours(v) in built surge protection device of minimum 4 KV.(Note:-Fitting should be 5 years standard Warranty/ Guarant

Supply, Installation, testing and commissioning of decorative Post top LED light fitting on existing pole having die cast housing / extruded aluminium Body on existing pole having following technical specifications with all accessories including connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and earthing as required.(i) Minimum lumen output 5400 lumen (ii) System lumen efficacy ≥ 100 Im/Watt (iii) CCT ≥ 5700, CRI > 80, PF≥ 0.95, THD < 10%, IP 65/66 (iv) L 70 rated life of 50 K hours (v) in built surge protection device of minimum 4 KV. (Note:-Fitting should be 5 years standard Warranty/ Guarantee)

Supplying and Erection of 6 mtrs. Long GI Octagonal Pole with bottom dia 130mm, top dia 70mm, company fabricated with 3mm thick GI sheet and base plate of size 200mm x200mm x12mm G.I. sheet i/c 4 nos. foundation bolts of size 20mm dia of suitable length, RCC foundation of size 500x500x1500 mm as per standard drawing of manufacturer, 2 nos. 750mm long 50mm dia B class GI protection pipe in each foundation to accomodate connection cable, bakelite sheet with 1 no. 6 amp SP MCB inbuilt within pole, with following type galvanised iron bracket welded at top i/c wiring of pole with 3x2.5 Sqmm FRLS PVC insulated copper conductor wire, testing etc as required. Single arm GI bracket 1 mtr long

Supplying and Erection of 6 mtrs. Long GI Octagonal Pole with bottom dia 130mm, top dia 70mm, company fabricated with 3mm thick GI sheet and base plate of size 200mm x200mm x12mm G.I. sheet i/c 4 nos. foundation bolts of size 20mm dia of suitable length, RCC foundation of size 500x500x1500 mm as per standard drawing of manufacturer, 2 nos. 750mm long 50mm dia B class GI protection pipe in each foundation to accomodate connection cable, bakelite sheet with 1 no. 6 amp SP MCB inbuilt within pole, with following type galvanised iron bracket welded at top i/c wiring of pole with 3x2.5 Sqmm FRLS PVC insulated copper conductor wire, testing etc as required. Double arm GI bracket 1 mtr long

Supplying, Installation, testing & commissioning of Cast Rasin Dry Type 500KVA 11/ 0.433 KV, 3 Phase, 50 Hz, Dyn 11 vector group, copper wound, class F insulation associated with winding temperature indicator/controller actuated by means of resistance temperature detector embedded in LV windings, indoor type Transformer with Approximately 5% impedance, tapping for off load operation on HV side in steps of +/- 2.5%, +/-5% - 7.5%, having cable end boxes on HV side suitable for 3x40sqmm XLPE cable of 11 KV grade and 800Amp. bus trunking arrangement on LV side with neutral brought out separately including supplying and laying of copper conductor multicore control cable from transformer to HT breaker for safety tripping, suitably mounted on M.S. Channel i/c supplying and grouting of suitable M.S. Channel with all accessories and confirming to IS 11171:1985 & as per specification attached complete in all respects as required at site.(Minimum efficiency Level-3 as per ECBC)

Supplying, Installation, testing & commissioning of cubical type LT panel suitable for 415 V, 3 Phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized designd from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 800 Amps. capacity extensible type TPN aluminium alloy bus bars of high conductivity, bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common G.I. earth strip of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with suitable size PVC insulated copper conductor S/C cable complete with necessary standard fittings as reqd at site i/c dismantling of existing LT panel and providing following switch gears. ( Face area not less then 5.0 SqM and depth not less than 1000 mm). Incoming : (i) 2 Nos. 800 Amps. 3 Pole, 50 KA, Manual draw out type ACB with micro- processor based release for protection against over load short circuits and earth fault. (ii) 1 No. 800 Amps 3 pole, 50 KA Manual draw out type ACB as bus coupler (without protection) (iii) 1 Set of 4 strip PVC sleeved Al.Bus Bar 1000 Amps. Capacity. (iv) 2 Nos. three phase multifunctional/ intelligent digital panel meter cum frequency meter i/c necessary CT’s etc. for measuring voltage, current, frequency, power factor, power & energy.(v) Suitable castle key arrangment for switching only one out of (i) & (ii) above.Outgoing : (i) 1 Nos. 630 Amps 3 pole, 50 KA Manual draw out type ACB with micro- processor based release for protection against over load short circuits and earth fault. (ii) 6 Nos. 350 Amps. TP MCCB-36 KA fault rating with rotary handle.(iii) 1 Nos. 250 Amps. TP MCCB-25 KA fault rating with rotary handle. (iv) 1 Nos. 150 Amps. TP MCCB-25 KA fault rating with rotary handle.(v) 1 Nos. 100 Amps. TP MCCB-16 KA fault rating with rotary handle. (Note:- All the MCCBs shall be of Ics=100%Icu )

Essential Panel Supplying, Installation, testing & commissioning of cubical type LT panel suitable for 415 V, 3 Phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized designd from CRCA sheet steel of 2 mm thick for frame work and covers, 3 mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 630 Amp capacity extensible type TPN aluminium alloy bus bars of hight conductivity, bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common G.I. earth strip of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with suitable size PVC insulated copper conductor S/C cable complete with necessary standard fittings as reqd at site i/c providing following switch gears.Essential Panel No.1:- (Face area not less than 5 Sqmtr. & depth not less than 1000 mm) Incoming : (i) 1 Nos. 630 Amps 3 pole, 50 KA Manual draw out type ACB with micro- processor based release for protection against over load short circuits and earth fault. 1 Set of 4 strip PVC sleeved Al.Bus Bar 800 Amps. Capacity.1 No. three phase multifunctional/ intelligent digital panel meter cum frequency meter i/c necessary CT’s etc. for measuring voltage, current, frequency, power factor, power & energy. Outgoing:-6 Nos. 350 Amps. 3 Pole MCCB 36 KA with rotary handle .1 Nos.200 Amps. 3 Pole MCCB 36 KA with rotary handle.1 Nos. 100 Amps. 3 Pole MCCB 25 KA with rotary handle.1 Nos.63 Amps. 3 Pole MCCB 16 KA with rotary handle . 1 Nos.Space for 320 Amps.TP MCCB (Note:- All the MCCBs shall be Ics=100%Icu)

Supplying & laying of one number power cable of 11 KV grade (Earthed HT Cable) of size 3 x 240 Sq. mm Al.conductor XLPE insulated flast strip armoured & over all PVC sheathed cable confirming to IS 7098, Part-II 1985 with latest ammendment in following manner as reqd.In the existing masonary open duct as reqd.

Supplying & laying of one number power cable of 11 KV grade (Earthed HT Cable) of size 3 x 240 Sq. mm Al.conductor XLPE insulated flast strip armoured & over all PVC sheathed cable confirming to IS 7098, Part-II 1985 with latest ammendment in following manner as reqd.Direct in ground as reqd.

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :240 sq. mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd. 2 x 10 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd. 3.5 x 35 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd. 3.5 x 70 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd. 3.5 x 185 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd. 3.5 x 240 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd. 3.5 x 300 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd. 3.5 x 400 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. 3.5 x 35 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. 3.5 x 240 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. 3.5 x 300 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing masonary open duct as required. 3.5 x 35 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing masonary open duct as required. 3.5 x 70 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing masonary open duct as required. 3.5 x 185 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing masonary open duct as required. 3.5 x 240 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing masonary open duct as required. 3.5 x 300 sq.mm

Supplying, laying of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size in the existing masonary open duct as required. 3.5 x 400 sq.mm

Supplying, laying and fixing of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size on cable tray as required. 3.5 x 35 sq.mm

Supplying, laying and fixing of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size on cable tray as required. 3.5 x 70 sq.mm

Supplying, laying and fixing of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size on cable tray as required. 3.5 x 185 sq.mm

Supplying, laying and fixing of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size on cable tray as required. 3.5 x 240 sq.mm

Supplying, laying and fixing of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size on cable tray as required. 3.5 x 300 sq.mm

Supplying, laying and fixing of one number XLPE insulated & PVC sheathed Aluminium Conductor armoured power cable of 1.1 KV grade of following size on cable tray as required. 3.5 x 400 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of XLPE Aluminium Conductor armoured power cable of 1.1 KV grade as reqd. 3½ X 35 sq. mm (32mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of XLPE Aluminium Conductor armoured power cable of 1.1 KV grade as reqd. 3½ X 70 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of XLPE Aluminium Conductor armoured power cable of 1.1 KV grade as reqd. 3½ X 185 sq. mm (57mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of XLPE Aluminium Conductor armoured power cable of 1.1 KV grade as reqd. 3½ X 240 sq. mm (62mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of XLPE Aluminium Conductor armoured power cable of 1.1 KV grade as reqd. 3½ X 300 sq. mm (70mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of XLPE Aluminium Conductor armoured power cable of 1.1 KV grade as reqd. 3½ X 400 sq. mm (82mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm widh x 62.5 mm depth x 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm widh x 50 mm depth x 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm widh x 62.5 mm depth x 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.450 mm widh x 50 mm depth x 2.0 mm thickness

Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying, Installation, testing & commissioning of Clean Agent Fire Extinguisher Capacity 04 Kg duly ISI marked conforming to IS: 15683:2006, with IS 14609, ISI marked HCFC 123 clean agent extinguisher complete with squeeze grip release valve, discharge pipe, locking arrangement, pressure gauge, operation manual and bracket etc as required.

CO2 type Fire Extinguisher ISI marked conforming to IS: 15683. Capacity 4.5 Kg. Complete with delivery hose horn, squeeze grip/ wheel type release valve, locking arrangement, operation manual and bracket complete as reqd.

Supply of water mist & CAF- 50 Ltr Capapcity Fire Extingusher, Trolley mounted Design Low pressure using Std AFFF Compound with fire rating 27A, 233B, 1000V safe to use for live electrical fire upto 35 KV etc complete as reqd.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required.

Supplying installation, testing and commissioning of 6 passenger (408 Kg.) Model : GeN2-Nova MRL or equivalent with stainless steel (machine room less) lifts having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specification enclosed and as under: PRODUCT: GeN2-Nova MRL or equivalent DETAILS: GeN2-Nova_MRL-1MPS or equivalent CAPACITY (kgs) : 6 Persons - 408 Kg SPEED (mps): 1.0 Metre/Sec (approx.) RISE (m): 6.3 m STOPS: 3 Stops With (all opening on the same side) CONTROLLER TYPE - ACD3-MRL or equivalent DRIVE: VF Regenerative (Closed Loop) POWER SUPPLY: 400/415 Volts (3 Phase AC)OPERATION : Full Collective Control CAR GROUP: One car (simplex) or equivalent MACHINE: PM Gearless (Located in shaft on top of guide rails TRACTION MEDIA: Flat Coated Steel Belt CAR FINISH: • Rear Mid Panel = Stainless Steel #4(Hairline)• Rear Corner Panels = Stainless Steel #4(Hairline)• Side Mid Panels = Stainless Steel # 4(Hairline)• Side Corner Panels = Stainless Steel #4(Hairline)• Front Panels = Stainless Steel #4(Hairline)FALSE CEILING TYPE: CD-41 FALSE CEILING FINISH: Stainless Steel #4(Hairline) VENTILLATION : Cross flow fan HAND RAILS :Stainless Steel Mirror Finish Handrails on rear car panels FLOORING: Vinyl Tiles CAR DOOR FINISH: Stainless Steel #4(Hairline) LANDING DOORS FINISH: Stainless Steel #4(Hairline) FIRE RATED DOORS : Fire rating-60mins (for both Lift and Landing Doors) PIT DEPTH : 1600mm OVERHEAD: 4300mm (from last stop/ landing) HOISTWAY DIMENSIONS (W x D – mm):1650 mm W x 1500 mm D CAR DIMENSIONS (W x D x H - mm): 1000 mm W x 1100 mm D x 2200 mm D CAR & HOISTWAY DOOR TYPE: Telescopic 2 speed doors DOOR OPENING (W x H - mm): 800 mm W x 2000 mm H DOOR OPERATOR: DC door operator system. COP: COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline) CAR POSITION INDICATOR: Monochrome LCD-Blue Background & White font Dot matrix (LED) Scrolling Display HALL FIXTURES: O2000 Pan Type Fixture , HALL FIXTURE FACE PLATE: Stainless Steel #4(Hairline)HALL BUTTON ARRANGEMENT: LCD Monochrome type STANDARD FEATURES: Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off OPTIONS INCLUDED: Emergency Firemen’s Service, Automatic Rescue operation, Voice Synthesizer, Intercom,

Supplying installation, testing and commissioning of 8 passenger (408 Kg.) Model : GeN2-Nova MRL or equivalent with stainless steel (machine room less) lifts having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specification enclosed and as under: PRODUCT: GeN2-Nova MRL or equivalent DETAILS: GeN2-Nova_MRL-1MPS or equivalent CAPACITY (kgs) : 6 Persons - 408 Kg SPEED (mps): 1.0 Metre/Sec (approx.) RISE (m): 6.3 m STOPS: 3 Stops With (all opening on the same side) CONTROLLER TYPE - ACD3-MRL or equivalent DRIVE: VF Regenerative (Closed Loop) POWER SUPPLY: 400/415 Volts (3 Phase AC)OPERATION : Full Collective Control CAR GROUP: One car (simplex) or equivalent MACHINE: PM Gearless (Located in shaft on top of guide rails TRACTION MEDIA: Flat Coated Steel Belt CAR FINISH: • Rear Mid Panel = Stainless Steel #4(Hairline)• Rear Corner Panels = Stainless Steel #4(Hairline)• Side Mid Panels = Stainless Steel # 4(Hairline)• Side Corner Panels = Stainless Steel #4(Hairline)• Front Panels = Stainless Steel #4(Hairline)FALSE CEILING TYPE: CD-41 FALSE CEILING FINISH: Stainless Steel #4(Hairline) VENTILLATION : Cross flow fan HAND RAILS :Stainless Steel Mirror Finish Handrails on rear car panels FLOORING: Vinyl Tiles CAR DOOR FINISH: Stainless Steel #4(Hairline) LANDING DOORS FINISH: Stainless Steel #4(Hairline) FIRE RATED DOORS : Fire rating-60mins (for both Lift and Landing Doors) PIT DEPTH : 1600mm OVERHEAD: 4300mm (from last stop/ landing) HOISTWAY DIMENSIONS (W x D – mm):1650 mm W x 1500 mm D CAR DIMENSIONS (W x D x H - mm): 1000 mm W x 1100 mm D x 2200 mm D CAR & HOISTWAY DOOR TYPE: Telescopic 2 speed doors DOOR OPENING (W x H - mm): 800 mm W x 2000 mm H DOOR OPERATOR: DC door operator system. COP: COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline) CAR POSITION INDICATOR: Monochrome LCD-Blue Background & White font Dot matrix (LED) Scrolling Display HALL FIXTURES: O2000 Pan Type Fixture , HALL FIXTURE FACE PLATE: Stainless Steel #4(Hairline)HALL BUTTON ARRANGEMENT: LCD Monochrome type STANDARD FEATURES: Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off OPTIONS INCLUDED: Emergency Firemen’s Service, Automatic Rescue operation, Voice Synthesizer, Intercom,

Excavation for Structure (Earth work in excavation of foundation of structures as per drawing and technical specification , including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottoms, backfilling th excavation earth to the extent required and utilising the remaining earth locally for road work.) Ordinary soil by manual means depth upto 3m without dewatering)

Construction of granular sub-base by providing coarse graded material, spreading in uniform layers

PCC 1 : 3 : 6 with crushed stone aggregate 40mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing fo 14 days.

RCC in open foundation.....without plasticiser , M-25, using concrete mixer

Providing weep holes with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing foce. Complete as per drawing and Technical specifications. 2no per metre length for 10 m=20 Nos

12.5cm thick slab :Funishing and placing Reinforced /Prestressed cement concrete in Sub- structure as per drawing and technical specification. RCC grade M25, using concrete mixure. a. Height upto 5 m

Supplying, fitting and placing TMT bar in sub-structure complete as per drawing and technical specifications.

Excavation for Structure (Earth work in excavation of foundation of structures as per drawing and technical specification , including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottoms, backfilling th excavation earth to the extent required and utilising the remaining earth locally for road work.) Ordinary soil by manual means depth upto 3m without dewatering)

Construction of granular sub-base by providing coarse graded material, spreading in uniform layers

PCC 1 : 3 : 6 with crushed stone aggregate 40mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing fo 14 days.

RCC in open foundation.....without plasticiser , M-25, using concrete mixer

Providing weep holes with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing foce. Complete as per drawing and Technical specifications. 2no per metre length for 10 m=20 Nos

12.5cm thick slab :Funishing and placing Reinforced /Prestressed cement concrete in Sub- structure as per drawing and technical specification. RCC grade M25, using concrete mixure. a. Height upto 5 m

Supplying, fitting and placing TMT bar in sub-structure complete as per drawing and technical specifications.

providing,fitting and fixing modular kitchen with stainless steel AISI-304 smartslide wire basket,trolly,cutlery tray,storage organizer, utility basket,corner utility storage, etc finished with FRP 12mm thick partition and shutter both side laminated with approved colour including wall mounted auto clean pyramid electric kitchen chimny of brand and make Tata or equivalent as approved with all nececcery fitting as for design and drawing

For Over head water Tank Earth work

piling work

c.c. work

soiling

shuttring work

R.C.C Work

plastring work

steel work

Supply of TATA FRP Oxidation Chamber Filter of 20000 LPH capacity with Single lever Multiport valve for backwash, rinse, bypass, filtration, etc., vacuum breaker, Distribution System, Media- Mno2, Grit, Gravels & Pebbles, 2” µPVC frontal pipeline.

Supply of TATA FRP Multigrade Sand Filter of 20000 LPH capacity with Single lever Multiport valve for backwash, rinse, bypass, filtration, etc., vacuum breaker, Distribution System, Media- Coarse Sand, Activated Carbon, Anthracite, Grit, Gravels & Pebbles, 2” µPVC frontal pipeline.

Supply of TATA FRP Iron Removal Water Filter with ISR Resin of 20000 LPH capacity with Single lever Multiport valve for backwash, rinse, bypass, filtration, etc., vacuum breaker, Distribution System. 2” µPVC frontal pipeline.

Supply of Automatic Soda Ash Dosing System. It includes Automatic Dosing Pump, HDPE 100 Ltr. Tank, Soda Ash and other fittings. Make : e-Dose or similar.

Supply of Water Transfer Pump. Capacity 5 HP. Make : Kirlosker or similar. (1 Working, 1 Standby)

Supply of Automatic Chlorine Dosing System, HDPE 100 Ltr. Tank, Sodium Hypocloride, NRV and other fittings. Make : e-Dose or similar.

Supply of Automatic Alum Dosing System, HDPE 100 Ltr. Tank, Alum, NRV and other fittings. Make : e-Dose or similar.

Test Kit (for Ch/ pH)

providing ,fitting and fixing pvc anti bird net /mesh 500 GSM framed with 40mm x 75mm 2class timber including briding 40mm x 15mm complete

Supply,Fabrication & Erection of M.S Structure of sections of SHS 100X100X5 & 60 OD Pipes along with12mm thick M.S Plates for fixing with the application of two coats of Red Oxide Primer.

Supply,Drilling and Fixing of 16 mm Anchor Bolts with the application of Epoxy chemicals

Supply,Fitting & Fixing of 16 mm thick Multiwall DPI Daylighting make Polycarbonate Roofing 6.2 Solo Opaque Sheets along with all aluminium accessories at site

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re- olling the sub grade and disposal of surplus earthwith lead upto 50 metres. Supplying and stacking at site. Good earth.

FIRE WATER TANK Earth work

P.c.c. work

soiling

shuttring work

R.C.C Work

plastring work

steel work

ENTRANCE GATE Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth , sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering.

Providing and laying in positon cement concrete of specified grade excluding the cost of centering and shutttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering , shuttering, finishing and reinforcement - All works up to plinth level: 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc, and removal of form for: Foundations, footings, bases of columns etc. for mass concrete

Centering and shuttering including strutting, propping etc, and removal of form for: Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc, and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc, and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured)Suspended floors, roofs, landing , beams and balconies (Plan area to be measured)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

12 mm Cement plaster of mix 1:6 ( 1 cement : 6 fine sand)

15 mm Cement plaster on the rough side of single or half brick wall mix 1:6 ( 1 cement :6 fine sand)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and olishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade Two or more coats on new work

GUEST HOUSE (HVAC)Supply Installation, testing and commissioning of Side Discharge Type outdoor units, with all multi scroll DC Inverter compressors for cooling & heating applications. The unit runs with inverter compressor only. All inverter capacity controlling compressors shall be suitable for 415 ± 10% volts, 50 Hz. special coated fins, panel, inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units. All ODUs are having Hi- POR technology for Oil return mechanism to high pressure side and Active Refrigerant Control systems to increase efficiency and performance of the unit. The manufacturer must be OEM for this project and must have manufacturing and testing facility in India. Unit shall yield COP of 3.69 at 100% load at AHRI condition ( Ambient 35Deg DBT & Inside : 19Deg WBT) . Conderser shall be capable to operate for outside ambient of 53 Deg C. All Outdoor unit must have " Ocean Black Fin " heat exchanger in the unit in dual layered & double sided with a black coating to shield it from Salt, Sand & other elements brought in by the air. Dual Sensing SLC ( Smart Load Control) - ODU-Dry Bulb Temperature & Relative Humidity. Outdoor Unit 16HP

GUEST HOUSE (HVAC)Supply Installation, testing and commissioning of Side Discharge Type outdoor units, with all multi scroll DC Inverter compressors for cooling & heating applications. The unit runs with inverter compressor only. All inverter capacity controlling compressors shall be suitable for 415 ± 10% volts, 50 Hz. special coated fins, panel, inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units. All ODUs are having Hi- POR technology for Oil return mechanism to high pressure side and Active Refrigerant Control systems to increase efficiency and performance of the unit. The manufacturer must be OEM for this project and must have manufacturing and testing facility in India. Unit shall yield COP of 3.69 at 100% load at AHRI condition ( Ambient 35Deg DBT & Inside : 19Deg WBT) . Conderser shall be capable to operate for outside ambient of 53 Deg C. All Outdoor unit must have " Ocean Black Fin " heat exchanger in the unit in dual layered & double sided with a black coating to shield it from Salt, Sand & other elements brought in by the air. Dual Sensing SLC ( Smart Load Control) - ODU-Dry Bulb Temperature & Relative Humidity. Outdoor Unit 20HP

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless Remote Hi-Wall Type 1.0 TR

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless RemoteHi-Wall Type 1.5 TR

Supply of Low Static Duct unit of following Capacities. The unit is having inbuilt drain pump & air purification. The set includes IDU & Cordless/ Corded Remote Low Static Duct Type 1.0 TR

Supply of Low Static Duct unit of following Capacities. The unit is having inbuilt drain pump & air purification. The set includes IDU & Cordless/ Corded RemoteLow Static Duct Type 2.0 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -2.0 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -2.5 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -3.5 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -4.0 TR

Y- Joints

Installation, testing & commisioning of 52 HP VRV System with 100 % DC Inverter Scroll Compressor, complete Indoor Unit as specified in equipment schedule along with low side works of Indoor installation, piping with nitrile insulation, drain pipe, nitrogen flushing, vaccuming, gas charging and balancing of the complete system.

Club house (HVAC)Supply Installation, testing and commissioning of Side Discharge Type outdoor units, with all multi scroll DC Inverter compressors for cooling & heating applications. The unit runs with inverter compressor only. All inverter capacity controlling compressors shall be suitable for 415 ± 10% volts, 50 Hz. special coated fins, panel, inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units. All ODUs are having Hi- POR technology for Oil return mechanism to high pressure side and Active Refrigerant Control systems to increase efficiency and performance of the unit. The manufacturer must be OEM for this project and must have manufacturing and testing facility in India. Unit shall yield COP of 3.69 at 100% load at AHRI condition ( Ambient 35Deg DBT & Inside : 19Deg WBT) . Conderser shall be capable to operate for outside ambient of 53 Deg C. All Outdoor unit must have " Ocean Black Fin " heat exchanger in the unit in dual layered & double sided with a black coating to shield it from Salt, Sand & other elements brought in by the air. Dual Sensing SLC ( Smart Load Control) - ODU-Dry Bulb Temperature & Relative Humidity. Outdoor Unit 20HP

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless Remote Hi-Wall Type .8TR

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless RemoteHi-Wall Type 2.5 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -2.0 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -3.0 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -3.5 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -4.0 TR

Y- Joints

Installation, testing & commisioning of 40 HP VRV System with 100 % DC Inverter Scroll Compressor, complete Indoor Unit as specified in equipment schedule along with low side works of Indoor installation, piping with nitrile insulation, drain pipe, nitrogen flushing, vaccuming, gas charging and balancing of the complete system.

MD (HVAC)Supply Installation, testing and commissioning of Side Discharge Type outdoor units, with all multi scroll DC Inverter compressors for cooling & heating applications. The unit runs with inverter compressor only. All inverter capacity controlling compressors shall be suitable for 415 ± 10% volts, 50 Hz. special coated fins, panel, inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units. All ODUs are having Hi- POR technology for Oil return mechanism to high pressure side and Active Refrigerant Control systems to increase efficiency and performance of the unit. The manufacturer must be OEM for this project and must have manufacturing and testing facility in India. Unit shall yield COP of 3.69 at 100% load at AHRI condition ( Ambient 35Deg DBT & Inside : 19Deg WBT) . Conderser shall be capable to operate for outside ambient of 53 Deg C. All Outdoor unit must have " Ocean Black Fin " heat exchanger in the unit in dual layered & double sided with a black coating to shield it from Salt, Sand & other elements brought in by the air. Dual Sensing SLC ( Smart Load Control) - ODU-Dry Bulb Temperature & Relative Humidity. Outdoor Unit 14HP

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless Remote Hi-Wall Type .1.3 TR

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless RemoteHi-Wall Type 1.5 TR

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless RemoteHi-Wall Type 2.0TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -1.5 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -3.0 TR

Y- Joints

Installation, testing & commisioning of 14HP VRV System with 100 % DC Inverter Scroll Compressor, complete Indoor Unit as specified in equipment schedule along with low side works of Indoor installation, piping with nitrile insulation, drain pipe, nitrogen flushing, vaccuming, gas charging and balancing of the complete system.

GM/DGM (HVAC)Supply Installation, testing and commissioning of Side Discharge Type outdoor units, with all multi scroll DC Inverter compressors for cooling & heating applications. The unit runs with inverter compressor only. All inverter capacity controlling compressors shall be suitable for 415 ± 10% volts, 50 Hz. special coated fins, panel, inverter based condenser fan M.S. hot dip galvanised stands / supports, electrical & microprocessor panel, isolating valves and all the necessary accessories for proper functioning of the units. All ODUs are having Hi- POR technology for Oil return mechanism to high pressure side and Active Refrigerant Control systems to increase efficiency and performance of the unit. The manufacturer must be OEM for this project and must have manufacturing and testing facility in India. Unit shall yield COP of 3.69 at 100% load at AHRI condition ( Ambient 35Deg DBT & Inside : 19Deg WBT) . Conderser shall be capable to operate for outside ambient of 53 Deg C. All Outdoor unit must have " Ocean Black Fin " heat exchanger in the unit in dual layered & double sided with a black coating to shield it from Salt, Sand & other elements brought in by the air. Dual Sensing SLC ( Smart Load Control) - ODU-Dry Bulb Temperature & Relative Humidity. Outdoor Unit 10HP

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless Remote Hi-Wall Type .1.3 TR

Supply of Hi-Wall unit of following Capacities. The IDU capable of discharging air in 6 different angles alog with jet cool and auto clean feature.The set includes IDU & Cordless RemoteHi-Wall Type 1.5 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette -1.5 TR

Supply of 4-Way Cassette unit of following Capacities. The unit is having inbuilt drain pump, human detection (optional), individual vane control& air purification. The set includes IDU, Panel & Cordless Remote 4 Way Cassette - 2.5 TR

Y- Joints

Installation, testing & commisioning of 10HP VRV System with 100 % DC Inverter Scroll Compressor, complete Indoor Unit as specified in equipment schedule along with low side works of Indoor installation, piping with nitrile insulation, drain pipe, nitrogen flushing, vaccuming, gas charging and balancing of the complete system.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, byspreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and upto 5 km lead complete (earth measured in stacks will be reduced by carriage 20% for payment).(PH Value between 5.5 to 7.5 & soil should be loamy)

Supplying and stacking sludge at site including royalty and carriage upto 5km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source,including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16 mm

Supplying and stacking at site dump manure from approved source,including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm

Supplying and stacking at site dump manure from approved source,including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Rough dressing the trenched ground including breaking clods.

Supplying and stacking at site dump manure from approved source,including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Fine dressing of the ground.

Spreading / filling of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Renovating lawns including weeding, cheeling the grass, forking the ground,top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed (the cost of sludge,manure and the good earth shall be paid for separately).

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 1.2 m dia and 1.2 m deep

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 90 cm dia, and 90 cm deep

Flooding the ground with water including making kiaries and dismantling the same

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. Flats

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge

Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge

Anti termite treatment by digging holes 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.and as per direction of officer-in-charge

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as perdirection of officer-in-charge.and as per direction of officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Tree Plant

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Shrubs/ Creepers

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Hedge Plant / Ground Cover

Cleaning and Sweeping of Lawn / Garden area and keep it neat and clean by mechanized method / manually, remove litter,debries, picking of leaves, papers, plastic bottles etc. including disposal of collected waste in dustbin/ designated place, as per direction of officer -in- charge (All T & P, materials/ articles shall be provided by the contractor.)

Removal of garden waste by tata 407 or eqivalent including loading / unloadingnand carriage upto 1 km lead, complete disposal upto designated place as per direction of officer -in-charge.

Providing and stacking of Nauclea cadamba (Kadam) of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge. Nauclea cadamba (Kadam) of height 150-165 cm

Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria acutifolia of height 150-165 cm. with 3-4 branches in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Mimusops elengi (Maulsri) of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Terminalia arjuna of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Saraca indica (Sita Ashok) of height 105-120 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Peltophorum species of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus bengalensis krishna of height 75-90 cm., multi branched in earthen pots of size 30 cm as per direction of the officer-in-charge

Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Fishtail palm of ht. 150-180 cm bottom girth 15-20 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Eugenia jambolana (Jamun) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Spathodea campanulata of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Psidium guajava of height 60-75 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Alstonia scholaris of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge.

Providing and Stacking of Curry leaf of height 75-90 cm in poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Terminalia arjuna of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Phyllanthus emblica (Amla) of height 150-165 cm. in Big HDPE Bag as per direction of the officer-in-charge.

Providing and stacking of Tabernaemontana coronaria (Chandni single) of height 45-60 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Tabernaemontana coronaria (Chandni single) variegated of height 60-75 cm., 5-6 branches in p.bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Caesalpinia pulcherrima species of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge

Providing and stacking of Largerstroemia indica of height 90-105 cm. multibranched in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and Displaying Ficus black vivion piller Topiary (sylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Ficus infectoria (Pilkhan) of height 150-165 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Hibiscus variegated of height 60-75 cm. with 8-10 branches and healthy variegated foliage in cement pot of size 35 cm

Providing and stacking Acalypha Different colour well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size of Earthen Pot/ Plastic Pot bushy plant as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum inerme having ht. 25 cm to 30 cm multi branched in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Calliandra hybrida of height 105-120 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 30-45 cm. with 3-4 branches and healthy foliage in p.bag of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Dianella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Wedelia trilobata, full of leaves in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of of Chlorophytum (Green), full of leafy suckers in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge

Providing and fixing G.I pipes complete with GI fittings including trenching and refilling etc.- 20mm dia nominal bore

Providing and fixing G.I pipes complete with GI fittings including trenching and refilling etc.- 40mm dia nominal bore

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc complete 25 to 40mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end) 20mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end) 40mm nominal bore

Painting G.I pipes and fittings with two coats of ani-corrosive bitumastic paint of approved quality 20mm diameter pipe

Painting G.I pipes and fittings with two coats of ani-corrosive bitumastic paint of approved quality 40mm diameter pipe

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge. Averrhoa- carambola (kordol) fruit bearing tree of of ht. 90-105 cm

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge.Aegle marmelos (bael) fruit bearing tree of of ht. 90-105 cm

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge. Citrus maxima (Robab tenga) fruit bearing tree of of ht. 90-105 cm

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge. Ziziphus Mauritiana (Bogori)fruit bearing tree of of ht. 90-105 cm

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge. Litchi chinensis (Lychee) fruit bearing tree of of ht. 90-105 cm

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge. Cinnamomum verum (dalchini) medicinal tree of of ht. 60-90 cm

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge. Yucca Silver (shrub) of of ht. 40-65 cm

Providing and stacking of following plants in big size HDPE bag as per direction of the officer-in-charge. Chrysopogon zizanioides (erosion grass)- Ground cover of ht. 20-30cm

Supplying 20mm dia rubber thermo plast hose pipe (EPDM) in 30 mtr. Roll, confirming to IS: 444 -1987; Type 3A.

Bamboo Caging of tree plantation with ( bhuluka or equivalent ) upto a height of 1.5m- above GL & 45 cm below pained with black japan paint

Supporting with bamboo stick having three layer tiding by thread for potted plants.

Supplying and stacking & application of fertilizers at site including royality and carriage D.A.P well packed in jute / gunny bags in 50kg wt.

Carbofuran 3G in 5 kg bag

Gypsum well packed in jute / gunny bags in 50kg wt.

Formation of a rockery including supplying of all relevant material like -earth , manure , pebbles stones , bricks , plants and all other allied items as required to a proper shape, size and height as directed by architect / consultant and as per drawing.

Supplyng, installation, testing & commissioning of water pumps of approved brand with all accesories complete as per direction of Engineer-in-charge / officer-in charge 0.5HP

Supplyng, installation, testing & commissioning of water pumps of approved brand with all accesories complete as per direction of Engineer-in-charge / officer-in charge 1.00HP

Supplyng, installation, testing & commissioning of water pumps of approved brand with all accesories complete as per direction of Engineer-in-charge / officer-in charge 1.50HP

Supplying portable Zinc impact sprinkler on tripod base with 12mm head adjustable to reach upto 80 ft. ( 24mtr) in diameter in partial to full circle.The tripod base should be adjustable from 0.40m to 1.00m ht.

Swimming pool Earth work

P.c.c. work

soiling

shuttring work

R.C.C Work

plastring work

steel work

supplying fitting and fixing Re -Cireculating Pump for Filtration .Max. output: HP. capacity 50 m³/hr.(2 working , 1 standby )Make : Aquanomics or similar.

Chemical Dosing Pump ( 1 for Ch, 1 for pH)Electronic dosing pump with CH regulations,Electronic dosing pump with CH regulations,IP-65 protection.Make : E- Dose or similar.

Pool Filter TOTALLY ANTY- CORROSIVE FRP Bobbin wound 900 mm Dia. Suitable for 50 m³/hr. flow rate. Make : Aquanomics or similar.

Multiport Valve Filtration, back-washing, rising and shut down of the filters. Make : Aquanomics or similar.

HDPE Storage Tanks Capacity of tank 100 lts

Drain Made in ABS White Plastic. Make : Aquanomics or similar.

Floor Inlet Make : Aquanomics or similar.

Overflow Gratings ABS (300 mm)Make : Aquanomics or similar.

Filter Media Sand, Grit, Gravels & Pebbles

LADDER Stainless steel ladder, 3- step Make : Aquanomics or similar

Suction Inlet Make : Aquanomics or similar. Under Water Lights Illumination

LED Underwater Lights SS 18 W.

Junction Boxes, with 3 entries 3/4" or PG-16 coupling

Flexible Cable Conduits

Vacuum hose 1 ½" dia 15 mtrs long including hose cuffs Make : Aquanomics or similar.

Suction head with wheels Make : Aquanomics or similar.

Extensible pole Make : Aquanomics or similar.

Curved brushes Make : Aquanomics or similar.

Algae Brush, SS bristles Make : Aquanomics or similar.

Deep bag net Make : Aquanomics or similar.

Test Kit (for Ch and Ph) Make : Aquanomics or similar.

Wires, Cables, Casing PVC Pipes, Panel Box, Switch, etc.

Pipes & Fitting, Agri, 6 KG pressure

Transportation & Installation Charges

Supplying and installation of Glass Mosaic including fixing chemicals, Grout, Adhessive etc with make Italia, Peopleo or Similar complete.

CHILDREN PLAY EQUIPMENT AND STREET FURNITURE` GGAS 16117 SUPER MAX PLAYZONE Area (feet) :33.8 X 32.1 X 13.5 Play Area (feet):37 X 35 MAKE: PLAYGRO or equivalent * Virgin quality plastics namely LLDPE , HDPE are used to make these products and UV stabilizers are also used wherever required to maintain the products colour and life of the products. * Galvanized steel pipes are also being used wherever required. *All the iron parts of the products are of G I pipes with non toxic powder coated paint upon it. No. of Components 1. Hut Shaped Roof : 2Pcs. 2. Single Curved Roof : 1Pcs. 3. Leaf & Flower : 1 Pc. 4. Tunnel Slider : 7'Ht. 1Pcs.5. Single Slider : 1Pcs. 6. Double Slider : 5'Ht.1Pcs. 7. MS Net Climber : 1 Pcs. 8. MS Perforated Square Deck : 5Pcs. 9. Ms Bridge : 1 Pcs. 10. Ms Box Ladder : 1Pcs. 11. Ms Step Ladder : 1 Pcs.12. MS Loop Set : 1 Pcs. 13. Part Slider : 7'Ht. 1Pcs. The Sizes mentioned are approx.

Park Bench MAKE: KIDZEDUZONE or equivalent Capacity: 03 persons Size: 5ft x 2ft x 3.5ft Seating Height: 2.5feet Leg material: Heavy Duty Cast Iron Seating Frame: 2" x 0.5" rectangular MS pipe

Dust BinMAKE: SUPREME or equivalent Material: HDPE Bottom Size: 13 inch x 13 inch Top Size: 20 inch x 20 inch Height of Bin: 28 inch Height of Bin Wit Lid : 36 inch Capacity: 100 litres

2 Seater A Swing MAKE: KIDZEDUZONE or equivalent Age: 4-14Yrs Capacity: 02 Children Area: 10feet x 5feet Safe Play Area: 16feet x 8feet Height: 9feet Leg Support: 3inch MS pipe Seat: Rubber Seat Bearing: Sp. Forged Alloy Steel Casing Suspension: 6mm Dia. Heavy Duty Chain Top Bar: 2.5inch MS. pipe

EPDM Floring for Park area 14 mm thick black Base + 6 mm thick colourful layer Black & Colourful Plastic Granules are pasted with adhesive are used for this purpose.

RAW WATER TANK Earth Work

P. c.c. work

soiling

shuttring work

R.C.C Work

plastring work

steel work

Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per Technical Specification Clause 408.i. For Grading - I Materials

Construction of Water Bound Macadam using locally available material (Table 400.13) Providing, laying spreading and compacting local material in block or large discrete particles, such as kankar, Laterite, Dhandla etc. as per Table 400.13 to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming requisite type of screening /binding materials to fill-up the interstices of laid material watering and compacting to the required density as per Clause 405.3 and Technical Specification Cluase 408. Grading - III

Providing, laying of Interlocking Concrete Block (ICBP ) with cement concrete paver block as per IS 15658-2006 of thickness 80 mm and of specific 28 days compressive strength over a layer of bedding sand of compacted thickness 30 mm , laid either stretcher /running /herring bone pattern of bonds as directed by the engineer in charge and in proper level and grade and compacted with appropriate equipment such as plate vibrator along with spreading of a thin layer of sand to fill up the gaps between blocks including construction of edge restraint whereever required complete as per drawing and technical specification clause no 1504 of MORD 80 mm Thickness

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1.

Construction of Water Bound Macadam using locally available material (Table 400.13) Providing, laying spreading and compacting local material in block or large discrete particles, such as kankar, Laterite, Dhandla etc. as per Table 400.13 to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming requisite type of screening /binding materials to fill-up the interstices of laid material watering and compacting to the required density as per Clause 405.3 and Technical Specification Cluase 408. By Manual Means Grading - II

Excavation for Structure (Earth work in excavation of foundation of structures as per drawing and technical specification , including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottoms, backfilling th excavation earth to the extent required and utilising the remaining earth locally for road work.) Ordinary soil by manual means depth upto 3m without dewatering)

Construction of granular sub-base by providing coarse graded material, spreading in uniform layers

PCC 1 : 3 : 6 with crushed stone aggregate 40mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing fo 14 days.

RCC in open foundation.....without plasticiser , M-25, using concrete mixer

Providing weep holes with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing foce. Complete as per drawing and Technical specifications.2no per metre length for 10 m=20 Nos

12.5cm thick slab :Funishing and placing Reinforced /Prestressed cement concrete in Sub- structure as per drawing and technical specification. RCC grade M25, using concrete mixure. a. Height upto 5 m

Supplying, fitting and placing TMT bar in sub-structure complete as per drawing and technical specifications.

Earth work in excavation in foundation trenches including refilling the quantity as necessary after completion of works of pipe line dressing, ramming, watering etc. and removal of surplus earth with 50 m lead and lift up to 1.5 m all complete including dewatering as directed including bailing out water where necessary.(a) Ordinary soil For pipeline

Construction of brick masonary valve chamber with 23 cm 1 st class brick in prop. 1:4 finished with 10 mm thick cement plastering prop. 1 :4 inside wall in floor including necessary earth work in excavation and refilling the sides of the same after completion of brick work. The size of chamber 60cm x 60cm x 120 cm inside with a RCC cover slab in 10 tor T.S @150 mm c/c both ways binding with black wire. Brick flat soling with 1:3:6 in the base of chamber complete as per specification and drawing approved by the Deptt.

Construction of platform of hydrant pillar with average 60 mm thick cement concrete in proportion 1:2:4 of size 1.45 m x 1.45 m (outside to outside) over one brick flat soling with one brickwork edging, all-round with mortar 1:4 and 10 mm thick cement plastering in proportion 1:3 to exposed surface, finished with neat cement and curing complete as per approved drawing of CPHE 08/05 including necessary earthwork and refilling after completion of work as specified and directed.

Construction of R.C.C. hydrant pillar of size 13 cm x 13 cm x 165 cm high (75 cm below G.L. & 90 cm above G.L.) in prop. 1:2:4 reinforced with 4 Nos. of 10 mm dia HYSD bars and 6 mm dia MS tie bars @ 150 mm C/C including cutting, bending and placing in position and binding with tieing wire complete with shuttering, curing, earthwork in foundation etc. and 10 mm thick cement plastering in prop. 1:4 to exposed surface finished with neat cement coat as per approved drawing of CPHE 08/05 including necessary earthwork etc. all complete as directed. (Hydrant pillar is to be constructed along with the platform at a time where it is necessary)

Construction of drain with cement concrete works in proportion 1:2:4 in slope 1:50 with a base layer of concrete of proportion 1:4:8 as per respective approved drawings including necessary earth work and refilling after completion of work all complete as directed.

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 80 mm dia

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 65 mm dia

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 50 mm dia

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 40 mm dia

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).40 mm diaG.I. Pipes (Medium Class)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).50 mm dia G.I. Pipes (Medium Class)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).65 mm dia G.I. Pipes (Medium Class)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).80 mm dia G.I. Pipes (Medium Class)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).100 mm dia G.I. Pipes (Medium Class)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).80 mm dia G.I Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).65 mm dia G.I Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).50 mm dia G.I Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).40 mm dia G.I Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I Union Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).80 mm dia G.I Union Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).65 mm dia G.I Union Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).50 mm dia G.I Union Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).40 mm dia G.I Union Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I Threaded flange

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).80 mm dia G.I Threaded flange

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).65 mm dia G.I Threaded flange

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).50 mm dia G.I Threaded flange

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).40 mm dia G.I Threaded flange

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I Bend

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).80 mm dia G.I Bend

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).65 mm dia G.I Bend

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).50 mm dia G.I Bend

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).40 mm dia G.I Bend

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I Elbow

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).80 mm dia G.I Elbow

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).65 mm dia G.I Elbow

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).50 mm dia G.I Elbow

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints).40 mm dia G.I Elbow

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 100 X 80 mm dia G.I Reducing Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)80 X 65 mm dia G.I Reducing Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)65 X 50 mm dia G.I Reducing Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)50 X 40 mm dia G.I Reducing Socket

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)100 mm dia G.I Nipple 150 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)80 mm dia G.I Nipple 150 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)65 mm dia G.I Nipple 150 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)50 mm dia G.I Nipple 150 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)100 mm dia G.I Nipple 225 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)80 mm dia G.I Nipple 225 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)65 mm dia G.I Nipple 225 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)50 mm dia G.I Nipple 225 mm long

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)100 mm dia C.I D.F sluice valve

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints)80 mm dia C.I D.F sluice valve

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 65 mm dia Bronze/ Gunmetal Full Way Valve (Zoloto or Equivalent)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 50 mm dia Bronze/ Gunmetal Full Way Valve (Zoloto or Equivalent)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 40 mm dia Bronze/ Gunmetal Full Way Valve (Zoloto or Equivalent)

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 50 mm dia double A/Release Valve

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 100 mm dia 3 mm thick rubber insertion (For 35(N))

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 80 mm dia 3 mm thick rubber insertion (For 35(N))

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 100 mm dia Bolts & Nuts (For 35(N))

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 80 mm dia Bolts & Nuts (For 35(N))

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 110 mm dia UPVC Service Saddle Piece

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 90 mm dia UPVC Service Saddle Piece

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 75 mm dia UPVC Service Saddle Piece

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 63 mm dia UPVC Service Saddle Piece

Sypplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. reflex valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints) 15 mm dia Bronze Ferrule Cock (Medium) (Zoloto or Equivalent)

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 65 mm dia G.I pipe

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 65 mm dia G.I socket

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 65mm dia G.I union socket

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 65 mm dia G.I Bend

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 65 mm dia G.I Threaded Flange

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 65 mm dia G.I Elbow

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 80 mm x 65 mm G.I Reducing socket

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 65 mm dia (225 mm long) G.I Nipple

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). Nuts & Bolts 65 mm dia

Supplying, carrying, laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work). 3 mm rubber insertion sheet 65 mm dia

100 mm dia Clear water pumping main Earth work in excavation in foundation trenches including refilling the quantity as necessary after completion of works of pipe line dressing, ramming, watering etc. and removal of surplus earth with 50 m lead and lift up to 1.5 m all complete including dewatering as directed including bailing out water where necessary. 1 x 105.00 m x 0.60m x 1.00m=91.30 Cu.M In ordinary soil

Supplying ,carrying laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work).100mm dia

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). (i) 100 mm dia

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I socket

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I union socket

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100mm dia G.I Bend

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I Flange

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia G.I Elbow

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia (225 mm long) G.I Nipple

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). 100 mm dia Non Return Valve

Supplying , carrying, placing in position, fitting and fixing C.I. sluice valve (with wheel & cap) C.I. Non return valve complete with supplying bolts and nuts, 3 mm thick rubber insertion sheet etc. (the tail pieces if required will be paid separately) all complete as directed (one valve and two flanged joints). Nuts & Bolts 100 mm dia

3 mm rubber insertion sheet 100Mm dia

Three phase Submerssible motor pump set (Texmo/ Crompton Greaves / Aquatic/ CRI/ V-Guard/ Calma make) suitable for 100 mm bore well and above 3 HP STAGE 7 to 40 with MCB controlled Submerssible motor pump set control panel 3.0 H.P. Three Phase

Supplying and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV grade solid Aluminium conductor up to 10 Sq mm balance standard conductor , XLPE Insulated , cores laid up , PVC tape inner sheathed , Armour (Aluminium for single core up tpo 70 sq. mm balance aluminium strip , Galvanized for cable up to 2 X 10 sq.mm , 4 x 6 sq.mm balance all galvanized steel strip ..................... sand cushioning etc. complete handling of surplus spoil, debries to proper place as specified and directed by the Deptt. (Nicco / Havells/ RPG/ CCI/ Polycab/ Gloster/ Finolex make or equivalent) 2 Core A2 XWaY A2XFaY b) 4.0 sq mm core UG cable

Supplying , carrying laying and fixing G.I. pipes complete with G.I. fittings specials with jointing materials and supplying the jointing materials all complete as directed excluding trenching and refilling of earth (external work).65 mm dia

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 65 mm dia G.I pipe

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 65 mm dia G.I socket

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 65mm dia G.I union socket

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 65 mm dia G.I Bend

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 65 mm dia G.I Threaded Flange

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 65 mm dia G.I Elbow

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 80 mm x 65 Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. mm G.I Reducing socket

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 65 mm dia (225 mm long) G.I Nipple

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. 63 mm dia full way valve

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed. Nuts & Bolts 65 mm dia

Supplying, cutting and threading G.I. pipes with requird size of thread including finishing the end all complete as directed.3 mm rubber insertion sheet 65 mm dia

Supplying and making bore hole horizontally across road or embankment for crossing distribution pipe line including fitting fixing of G.I. casing pipe of required dia excluding the cost of pipe all complete as directed by the deptt.150 mm dia G.I pipe for casing

Supplying and making bore hole horizontally across road or embankment for crossing distribution pipe line including fitting fixing of G.I. casing pipe of required dia excluding the cost of pipe all complete as directed by the deptt.Bhaluka Bamboo

Supplying and making bore hole horizontally across road or embankment for crossing distribution pipe line including fitting fixing of G.I. casing pipe of required dia excluding the cost of pipe all complete as directed by the deptt. Coconut Rope

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2.00 m below the existing G.L.In ordinary soil

Shuttering and shoring the earth at different levels in foundations where necessary with required prop, struts, planks, timbers, nails etc. including dewatering if necessary, complete as directed and specified (measurement to be taken in the face area timbered)Upto a depth of 1.5 metre

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).(a). In prop. 1:3: 6 (1 cement:3 coarse sand : 6 coarse agg. by volume (using mixture machine)

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.Brick on flat soling.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level).a) From primary producer : TATA/ SAIL/ Jindal steel/ Shyam steel/RINL (i) TMT corrosion resistant steel (CRS)

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.Using 38mm thick plank

Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using mixture machine In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M25 grade concrete

10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. (b). In cement mortar 1:4

Preparation of site for placement of the drilling rig including excavation of mud pit, circulation drain, collection chamber etc. all complete as directed.

Construction of temporary accommodation and low cost sanitary facility for drilling staff including cost of camp materials viz. cots, tables, chairs, utensils, dresses, safety helmets etc. and dismantling the accommodation after completion of the work all complete as directed.

Providing water supply facilities at drilling site all complete as directed. By installing 1 Nos. of Singur hand pump

ReJAHAng in hard soil / pebble / gravel by bit of size either 8 1/2" or 9 5/8" or 12" from either 5 5/8" or 6 7/8" or 7 7/8" all complete as directed.

ReJAHAng in soft soil / normal clay / sandy soil by bit of size either 14" or 16" or 18" from either 8 1/2" or 9 5/8" or 12" all complete as directed.

ReJAHAng in hard soil / pebble / gravel by bit of size either 14" or 16" or 18" from either 8 1/2" or 9 5/8" or 12" all complete as directed.

Extraction of drilling pipes / bits against skin friction at the end of each day and after completion of the operation including washing of the bore hole all complete as directed.

ReJAHAng in soft soil / normal clay / sandy soil by bit of size either 14" or 16" or 18" from either 8 1/2" or 9 5/8" or 12" all complete as directed.

ReJAHAng in hard soil / pebble / gravel by bit of size either 14" or 16" or 18" from either 8 1/2" or 9 5/8" or 12" all complete as directed.

Extraction of drilling pipes / bits against skin friction at the end of each day and after completion of the operation including washing of the bore hole all complete as directed.

Supplying , sinking, lowering, fitting, fixing in position of 150 mm dia U.P.V.C. pipe assembly comprising of strainer, pipes and cone in potable water bearing strata, washing the bore well etc. and supplying necessary jointing materials including carriage of materials and cleaning and priming the tube well all complete as directed. (a) 150 mm UPVC pipe:For 0 to 50 m depth

Supplying , sinking, lowering, fitting, fixing in position of 150 mm dia U.P.V.C. pipe assembly comprising of strainer, pipes and cone in potable water bearing strata, washing the bore well etc. and supplying necessary jointing materials including carriage of materials and cleaning and priming the tube well all complete as directed. 150 mm UPVC pipe for 50 to 100 m depth

Supplying , sinking, lowering, fitting, fixing in position of 150 mm dia U.P.V.C. pipe assembly comprising of strainer, pipes and cone in potable water bearing strata, washing the bore well etc. and supplying necessary jointing materials including carriage of materials and cleaning and priming the tube well all complete as directed. (c) 150 mm Ribbed Screen

Developing of the D.T.W. with air compressor, Make- Kirloskar / Cumins all complete as directed.

Supplying and packing pea gravel around the periphery of casing including screening, washing etc. all complete as directed.

Supplying, fitting, fixing MS clamp of size 15 mm thick and 150 mm width having projection of 300 mm and three holes of 20 mm dia for clamping the plates by 16 mm dia hexagonal bolts of length 75 mm and nuts on both sides encircling the column pipe including two coat of enamel paint over one priming coat of different dia all complete as directed and specified.150mm Dia

FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL) Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Two pair, 2-core, 1.5 sqmm

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 88 m Head

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 200 mm. dia (wall thickness = 6.3 mm)

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 200 mm. dia (wall thickness = 6.3 mm) 150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 32 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 40 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 200 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 250 mm dia

Supplying and fixing Single headed internal/ external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 200 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 150 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 200 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 200 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :4 way-150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Upright Sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :100mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 700 mm

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1000 mm

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1500 mm

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Providing and fixing of 4.5 Kg. carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating gauge ingernal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming ro IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with internal charge.

Providing and fixing 6.0 Kg. ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating gauge internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with inernal charge.

Providing, fixing, testing and commissioning of 50 Litres (trolley mounted) Mechanical Foam type Fire Extinguisher. In HP Mild Steel Cylinders ISI marked TAC approved fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged complete in all respects including wall suspension bracket / trolley mounted and confoming to IS:13386 .

Portico of Size 7200mm X 6000mm Fabrication and erection of MS structure with SHS 150X150X5 and SHSI00XI00X4.5 sections of Tata / Nezone make (IS 4923YST 310 grade) for Glass Portico of size 7200mm X 6000mm as per design enclosed along with application of two coats of red oxide primer.

Supply and installatrion of 10mm + 10mm clear glass PVB(Poly Vinyl Butyral) sandwitched, total thickness 22mm approx. Pasted to the 1 Structural member with both side adhesive pressure tape and Silicon filling

Providing protective coating system by supplying and application of two coats of Synthetic Enamel paint complete conforming to IS17244.

Supply, Drilling and Fixing of M16x160 Anchor Bolts with the application of Epoxy chemicals

Portico of Size 7200mm X 4500mm Fabrication and erection of MS structure with SHS 150X150X5 and SHSI00XI00X4.5 sections of Tata / Nezone make (IS 4923YST 310 grade) for Glass Portico of size 7200mm X 4500mm as per design enclosed along with application of two coats of red oxide primer.

Supply and installatrion of 10mm + 10mm clear glass PVB(Poly Vinyl Butyral) sandwitched, total thickness 22mm approx. Pasted to the Structural member with both side adhesive pressure tape and Silicon filling

Providing protective coating system by supplying and application of two coats of Synthetic Enamel paint complete conforming to IS 17244.

Supply, Drilling and Fixing of M16x160 Anchor Bolts with the application of Epoxy chemicals

KMV Projects Limited