ADDN/ALTN AND SPECIAL REPAIRS TO T-102, PROVISION OF CHAIN FENCING AROUND ASHIYANA (BLDG NO P-406), PROVISION OF ALUMINIUM GRILL IN WINDOWS OF 1ST FLOOR OF GANGA BLOCK AND REPAIRS TO RAMP AND PROVISION OF STAINLESS STEEL RAILING OF WTC (P-413A) AT IN

Amount

Dismantling floor, hearth or wall tilling including cement mortor bedding (but not backing), removing serviceble tiles to store and rubbish off the premises complte all as specified.

Demolition of Brickwork or stone/bou-lder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Coloured Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed in CM 1:6

M&l for Glazed ceramic tiles of any colour in vertical surfaces 300 x 600x 8mm thick mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat cement plaster in CM 1:4 including refixing electric points and switch boards where as specified and as directed

Vitrified ceramic tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, as in floors/ walls etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20mm thick screed bed in CM 1:4

M & L RCC type B1, 1 :2:4 (using 20mm graded sotne agregate) in slabs suported in walls and the like and including demolition of old reinforced cement concrete of any escription, in any position complete all as speified.

M &L for use and waste of form work to soofits of suspended slab and the like fair finished flat complete all as specified.

M & L for mild steel TMT bars upto 8mm dia cut to lenth, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed ) not less than 0.9

M & L for Mild steel TMT bars upto 10mm dia cut to lenth, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed ) not less than 0.10

M&L for 18 to 20 mm thick Granite (of any type) work in single piece (table rubbed and polished) in steps, floors, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade over and including 20mm thick CM (1:6) bedding layer complete all as specified and as directed.

M&L for Brickwork with Modular bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 in narrow widths including Cutting out bricks/stone, for- ming toothing for, and bonding new into old brickwork /stone masonry

M&L for half Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in in CM 1:4

M&L for Rendering 15 mm thick CM 1:6 on fair faces of brick work or concrete surfaces and to be finished even and smooth(without using extra lime or cement)

M&L for Preparing newely plastered surface and primng with alkali resistant priming paint and applying 2 coats of oil bound distemper on walls over 3 mm thk wall care putty

M&L for Preparing newely plastered surface and primng with alkali resistant priming paint and applying 2 coats of antifungal weather proof paint exterior grade emulsion paint complete all as specified and as directed.

M&L for preparation of old surfaces of wall and applying two coats of oil bound distemper complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces including removal of old paint and preparation of surface all as specified and as directed.

Dismantling of cast iron/PVC or reinforced concrete drain pipes, jointed in cement mortor anf taking out of trenches if required 100/75 mm internal dia pipe complete all as specified.

S&F PVC (SWR) pipes of dia 110mm bore single socketed in any length with rubber ring joints fixed to walls/in trenches.

S&F PVC (SWR) pipe of 75 mm bore in single socketed in any length with rubber ring joints fixed to walls..

S&F PVC (SWR) bends of 110 mm dia bore

S&F PVC(SWR) vent cowl of 110mm dia bore.

M & L PVC Nahani trap 75mm size with grating including jointing to waste pipe fixed in cement concrete type type B1 (1:2:4)

S&F PVC Bottle trap having minimum water seal of 25mm (Minimum weight 32mm-260gms/40mm-270 gms) of 32 mm dia, complete all as specified and as directed.

S & F in repairs Wash basin wall hung with half pedestal 550x400 mm as per CERA -CAT No. S2040105 wash basin and Cat No S2090102 Half pedestal including waste pipe connections and pillar tap complete all as specified

S&F in repairs two piece EWC 680x360x765mm white, with seat cover and Twin flushing cistern complete all as specified and directed by Engr-in-Charge as per CERA -CAT No. S1021103 S Trap 230mm, CAT No S1060101 Cistern, CAT No B1510101 seat cover, CAT No B1810101 Twin Flush fittings all as specified

Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm

S&F Bib taps 15 mm dia, fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm dia pipe.

S&F Stop valves 15 mm dia, fancy type chromium plated, screwed down, high pressure, screwed both ends for 15mm dia pipe or for unions fixed in repairs

S & F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F Brass chromium plated overhead shower rose 120 mm dia with 3 flow with swivel joint, including shower arm, fixing to steel pipe or union including taking down old shower rose complete all as directed and specified by Engr- in- Charge. Make Cera shower rose F7020305 shower arm F7040104 or equivalent in Hindware/ Parryware.all as specified and directed

CP hand Health faucet of brass body with wall hook and 1mtr stainless steel braided rubber hose pipe fixed in repair complete all as specified and as directed.Make: Cera Cat No F8030102 or equivalent in Hindware / Parryware.

S&F in repairs pvc flexible waste pipe of length n exc 1m and dia 32/40mm fixed to wash basins.

S&F Stainless steel soap dish, white of size 160X160X90 mm as approved fixed with brass screws or embedded in wall . Make : Cera Cat No. F5003106 or equivalent in other makes as specified

Towel rail brass chromium plated fancy type 60cm long including bracket fixed between flanges complete Make: Cera Cat No. F5007103 or equivalent in Hindware/ Parryware

Taking up or down steel tubing of bore 15/20 mm and connection, including cleaning for refixing or removal complete all as specified.

Taking up or down steel tubing 25/32 mm and connection, including cleaning for refixing or removal to store complete all as specified.

S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6 kgf/sqcm conforming to IS-15778 with all fittings such as Tee,Bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls/ floors (Conceled where required) with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure

S&F CPVC pipes, SDR 11, 25 mm outer dia of pressure rating 6 kgf/sqcm conforming to IS-15778 with all fittings such as Tee,Bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls/ floors (Conceled where required) with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure

S&F Powder coated aluminium alloy curtain rod of any size including fancy type brakets all as directed by Engg-in-charge

Taking down chowkats or frames N.exc 1.5 Sqm with shutter (without taking of shutter from the frame.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

Providing 30mm thick "RAJSHRI" BRAND FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 500 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.

S & F 100 mm size Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11

S&F Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed 200mm long.

S&F 300mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed

S&F 100mm Extruded brass handles, fabricated type polished

Taking down (dismentling)wall and ceiling boards(fibre, pulp, insulation, etc) or insulation boards/slab/blankets, any thickness, including cover fillets complete all as specified and as directed.

S&F 4mm thick Non Asbestos (E-Board) designer tiles of approved design suitably fixed in false ceiling grid/frame with staples or screws complete in repair all as specified and as directed.

S&F Powder coated aluminium snap grid frame work of size 605x605mm for false ceiling all as specified

Taking down steel/aluminium windows/ventilator of any size with all fittings complete

M&L for powder coated aluminium three track and three shutter (of equal width) sliding type window without sash bars including necessary jointing clips, rubber packing, neoprene rubber gasket, aluminium snap beading, screws, aluminium fittings, handles, locking arrangement (star lock), bearings two No's for each shutter with 4.00mm thick sheet glass for glazing shutters & stainless steel wire cloth of 0.36mm nominal dia of wire & average width of aperture 1.40mm for wire gauge shutters including following powder coated sections as given in 'JINDAL' catalogue complete all as specified and as directed :- (i) Frame (Bottom)-20620. (ii) Frame (Top & Side)-20621. (iii) Shutter vertical (Handle lock)-20846. (iv) Shutter vertical (Int lock)-20845. (v) Shutter (Top)-20844. (vi) Shutter (Bottom)-20847. Note :- (i) The window opening shall be provided with three shutters of equal width. (ii) Two shutters shall be glazed shutters & one shutter shall be with stainless steel wire cloth all as specified hereinbefore. (iii) The shutters shall be placed in such a manner that at a time the entire width of window can be utilized as fully glazed window and at time the same can be utilized as partly glazed and partly gauzed window. (iv) The thickness of powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE. (v) Sealing the gap of frame with Jamb and Cill (alround) using silicon gel at the rate of 0.05 lit/m for both faces of window.

Supply and fix aluminium powder coated fixed type ventilator without sash bar, centre to centre distance of horizontal members not exc 60 cm & vertical members not exc 45 cm with 4 mm thick plain sheet glass,rubber packing with & including following powder coated section as given in 'JINDAL' catalouge complete all as specified and as directed. (i) Frame (SP) -20052 (ii) Frame (DP) - 20051 (iii) Glazing clip - 19352

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar all as specified and directed

PCC (1:4:8) type D2 (using 40 mm graded stone aggtegate) as in foundation filling and mass concrete

M&L for filleting section of fillet exc 25 but n.exc 50 sq cm in cement mortar 1;3 in any shape in cement mortar.

M&L for coloured chequered cement concrete tiles 30cm X 30cm X 25mm thick set jointed & pointed in neat cement slurry with grey cement and pigments ove 20 mm thick screed bed in CM (1:6) complete all as specified

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M & L for Point wiring with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box fixed with suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed. (a) One light point or one fan point or bell point controlled by one switch

One 3 pin socket outlet, 5 Amp independent

One 3 pin socket outlet, 5 Amp on the same board with other switches

One bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 sq mm size.

All as per item No.2 here in before but wiring with cables of size 2.5 sqmm for wiring & cables of size 2.5 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 3 pin Switch/Socket outlet on Independent board complete all as specified and directed. (Note : cutting chases & making good of disturbed surfaces shall be measured and paid separately).

S & F switch piano, 5 Amp, single pole, flush type one way 230 volts complete all as specified and as directed.

S & F socket out let, 2 in 1, 3 pin, 5 Amps, 240 volts complete all as specified and directed.

S & F Switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts complete all as specified and directed.

S & F Switch socket combination, 5 in 1, 5/15 Amps, 240 volts, flush type with fuse & neon incator complete all as specified and directed.

S & F Ceiling rose, 3 way PVC insulated body complete all as specified and directed by engineer in charge.

S&F of Tubelight Rod ultra bright LED tubelight with very high efficacy suited for installation in existing tubelight G13 lamp holder to give glare free light for 18W20W/22W complete all as required at site and as directed by Engineer -in-Charge. Make : Havells,CRYSTAL812DSTL20WLED865GLASS or equivalent of Bajaj/Philips / Wipro

S&F of surface and wall mounted reagal batten for 18W20W/22W compact batten suitable for single LED Tubelight with integral LED driver complete with all accessories complete all as required at site and as directed by Engineer -in-Charge. Make : Havells,REGALBATTENT8UPTO1X22WSSBSWH or equivalent of Bajaj/Philips / Wipro

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make: Crompton or equivlent Bajaj/Philips/Havells

S/F switch bell push, flush type 5 Amp.

S&F in repairs bell, electronic type AC, 230 Volts single pole.

M&L lamp holder, PVC/ poly carbonate type with black plate suitable for batten fittings.

Supply and fix new adore LED lamp 9 Watt confirming to Cat No LHLDBWH4L8R009 of Havell's or euivalent in Philips / Bajaj

Supply and fix Inverter Bulb LED lamp 9 Watt confirming to Cat No LHLDEGEDML8009 of Havell's or euivalent in Philips / Bajaj

Labour only for taking down and fixing repairs to Ceiling Fan with Fan regulator/Exhaust Fan, any Make & any Sweep Oiling, Greasing , removing all dust with painting and Rewinding of fan by super ennameled copper insulated wire as per existing gauge, varnishing, heating assembling and testing for serviceable condition complete all as directed by Engineer-in-Charge.

S&F in repairs fan regulator electronic step type complete all as directed by EIC at site

Supply and fixing LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.Make: Crompton or equivlent Bajaj/Philips/Havells

Taking down electric meter of any type and any make single/three phase by dismantling of all electrical connection checked the meter ,and Refixed same Nos of meter on wooden board in metal box of suitable size in same Nos of qtr after repair works completed

S&F in repairs MCB DB TPN 6 ways double door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed Make: HAVELLS, Standerd/Legrand Complete all as specified and as directed.

S&F in replacemen MCB DB SPN 8 ways double door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed

S&F in repairs MCB SPN 40 to 63 AMP, 240 Volts 10KA 'C' curve , Complete all as specified and directed.

S&F in repairs MCB FP 40 to 100 AMP,415 V with adjustable thermal and adjustable magnetic release,Make- HAVELLS, Standerd/Legrand Complete all as specified and as directed.

S&F in repairs MCB SPN 32 AMP, 240 Volts 10KA 'C' curve , Complete all as specified and directed.

S&F in repairs MCB SP 5 To 32 AMP, single pole 240 Volts 10KA 'C' curve, Complete all as specified and directed.

Taking down sub main wiring of any size from the ceiling, walls etc and incl making good to disturb surface of wall and match with the existing surface.

M&L for sub main wiring drawing through PVC casing and capping with four runs of single core 6 sq mm and two runs of 6.0 sq mm as earth wire of stranded copper conductor PVC insulated and unsheathed cable of 1100 volts grade all as directed.Note:- Two run of 6 sqmm wire and One run of 6 sqmm wire and One run of PVC casing caping will be measured as one running meter.

M&L for earthling complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR part1991,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on complition.

M & L for cutting/making hole for fixing of ser item No 15 and making good disturbed surface with existing surface all as specified and directed by Engr-in-charge.

M&L for sub main wiring drawing through PVC casing and capping with Wiring alongwith earth wire size 2x2.5 sq. mm + 1x2.5 sq. mm earth wire of FRLS is PVC insulated copper conductor, single core cable in surface/recessed as required .Note:- Two run of 2.5 sqmm wire and One run of 2.5 sqmm wire and One run of PVC casing caping will be measured as one running meter.

Supply ,laying and testing cable XLPE insulated,screened,PVC bedded,galvanized steel strip or wire armoured,electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete all as specified and as directed.

Supply and lay in trenches / along the wall / floor pipes GI light grade of size 50 mm dia with and including all fittings and accessories including taking down old U/S pipe complete all as specified and and directed for cable protection

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out hard dense soil.

Removal excavated surplus soil to a distance n.exc. 50 m and depositing where directed at level n.exc. 1.5 m above the starting point all as directed by Engr-in-Charge.

Excavation in trenches n.exc 1.5m wide n.exc 1.5m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 Sqm on plan and n.exc 1.5m depth and getting out in hard dense soil

M&L for providing cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in foundation, bed blocks,filling and mass concrete

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete.

S & F Mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165

Supply only chain link fencing, MS galvanised of any size and type complete all as specified and as directed by Engr in Charge.

Fixing only chain lnk fencing including line wires, any mesh, size, any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed Note : chain link fencing shall be measured and paid separately as " supply only"

Preparing new or previously untreated steel surface of any description, over 10 cm in width or girth not other wise described and appying two coats of synthetic enamel paint over red oxide primer.

S&F fixed 5 to 10 mm dia Mild steel screws bolts(Machine made)with hexagonal or square heads at one end and screwed both ends ,each screwed end to be fitted with washers and one hexagonal or squre nut, lentg of bolt exc 5cm and n.exc 10cm long. With washers.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer?in-charge.

S&F for 4 mm Sheet glass, ordinary quality and glazing as in Aluminiu windows, Doors, Ventilators etc in square/ rectangular shape n exc 0.5 sq.m in each pane including taking out and removal of old glass all as directed.

S&F for 5 mm Sheet glass, ordinary quality and glazing as in Aluminiu windows, Doors, Ventilators etc in square/ rectangular shape exc 0.5 sq.m in each pane including taking out and removal of old glass all as directed.

S&F in Repairs galvanised steel steel wire cloth, 0.63 nominal dia of wire and average width of aperture 1.0 mm and fixed to wooden skeleton shutter/ Aluminium windows all as directed.

S&F Aluminum powder coated partitions, partly panelled & partly glazed with 12 mm thick both side laminated MDF board in bottom panel and 5mm thick tinted glass in top panel fixed with clips, aluminium beads, rubber gaskets etc., centre to centre distance of vertical member shall n.exc 1mtr and horizontal members shall n.exc 1.10 mtr using following aluminum powder coated section as mentioned in Jindal Catalogue complete all as specified & as directed :- (a) SP – 20048 (b) DP - 20047 (c) Glazing clips - 19352

Demolition of Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M & L PCC (1:2:4) type B-2 (Using 40 mm graded stone agg.) as in foundation.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240

S&F Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment of FE 410-W (Gde-E-250) quality B

M&L preparation of new steel surfaces of any descriplain, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer all as specified and as directed.

DWARKESH STRUCT-CON

M/s S.D Construction Co

JADHAV CONSTRUCTION AND INFRASTRUCTURE

SHAILENDRA B TULSANI

VIJAYA ENTERPRISES