SPECIAL REPAIR TO BLDG NO P-5 (QTR NO 01 TO 08) OF OR MD ACCN AT STAGING CAMP AT NEW CANTT ALLAHABAD

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer in Charge.

M & L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10mm thick in cement mortar 1:4 finished rough to receive wall tiles etc complete all as specified and directed by Engineer in Charge.

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer in Charge.

M & L for Non skid ceramic colour tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engineer in Charge.

All as per Ser item No 04 here-in-above but on vertical surfaces including 10mm thick screed plaser in CM 1:4 ,complete all as specified and directed by Engineer in Charge.

M & L for Dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by Engineer in Charge.

M&L 40 mm thck brick tiles laid on water proofing membranes and jonted flush pointed in CM 1:3 with 5% of linseed oil incl bedding in cement in CM 1:4 20 mm thick shall be cured with water complete all as specified and directed by Engineer in Charge.

All as per Ser item No 07 here-in-above but except tiles( old tiles shall be used) complete all as specified and directed by Engineer in Charge.

Demolition of mud in roofs, any thickness, including plastering and leeping ( whether full thickness removed or only a part thereof) complete all as specified and directed by Engineer in Charge.

Removing of surplus excavated/demolised materilas to a distance exc 250mtr but n.exc 500m and deposited where directed at a level n. exc 1.5 m above the starting point complete all as specified and directed by Engineer in Charge.

M&L cutting crack to 'V' groove section in existing roof cleaning out wetting grouting with cement and sand slurry of 1:3 complete all as specified and directed by Engineer in Charge.

M&L PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in roof kerbs / benching / coving and roof padding over roof surfaces /sunken treatment etc rounded or chamfered on edges, complete all as specified and directed by Engineer in Charge.

M & L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- (a) 10 mm thick plastering in CM (1:3) using 100 % coarse sand on roof / parapet walls with WPC @ 3 % by weight of cement. (b) Applying a coat of bitumenous primer confirming to IS-3384-1986 @ 0.40 ltrs/Sqm on prepared surfaces and allow to dry. (c) Supply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 Kgs/Sqm. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

M&L for preparation of new or previously untreated surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of bituminous aluminium paint, complete all as specified and directed by Engineer in Charge.

Supply only integral water proofing compound

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area exc1.5 but n. exc 4 Sqm each complete all as specified and directed by Engineer in Charge.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm each.

Taking down shutters of any description exc 1 Sqm each and and removing to store etc all as specified & directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed by Engineer in Charge.

S&F Factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer in Charge.

S&F pressed steel frame for door with one or more rebates size 125x60mm including necessary fixing lugs, lock striking plates,hinges,hold fast etc. complete size /profile of frame as per IS complete all as specified and directed by Engineer in Charge.

S&F pressed steel frame for door with one or more rebates size 105x60mm including necessary fixing lugs, lock striking plates,hinges,hold fast ,etc. complete size /profile of frame as per IS complete all as specified and directed by Engineer in Charge.

S & F Flush shutters 35 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and directed by Engineer in Charge.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat,complete all as specified and directed by Engineer in Charge.

S&F Stainless steel wire mesh 0.36 mm dia fixed with tinned tacks of stainless steel wire and avg width of aparture 1.4mm complete all as specified and directed by Engineer in Charge.

S&F Steel ventilators, fixed type, with glazing bars complete all as specified and directed by Engineer in Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engineer in Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed by Engineer in Charge.

S&F window guard bars, plain let in and fixed independently in wooden frames L or T section support for shelves etc., and similar articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer in Charge.

S & F 4 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in square area exc. 0.5 Sqm in each pane complete all as specified and directed by Engineer in Charge.

S & F 4mm thick plain sheet glass pin headed and glazing with oil putty or wooden beads in square area exc. 0.5 Sqm in each pane complete all as specified and directed by Engineer in Charge.

S&F /fabrication in repair cupboard made out of 16 to 18mm thick PVC board plain sheet complete all as specified and directed by Engineer in Charge.

S&F /fabrication in repair cupboard made out of 16 to 18mm thick PVC board laminated shhet complete all as specified and directed by Engineer in Charge.

Supply and fix continues (piano) hinges, mild steel, bright finish width of flap (when open) 30mm complete all as specified and directed by Engineer in Charge.

S&F magnetic catches with steel body ‘H’ type, fixed to shutter complete all as specified and directed by Engineer in Charge.

S & F 75 mm dia aluminium handle cast type anodised complete all as specified and directed by Engineer in Charge.

S & F 125 mm dia aluminium handle cast type anodised complete all as specified and directed by Engineer in Charge.

S&F Locks, cupboard, grade I, size 50mm complete all as specified and directed by Engineer in Charge.

M&L plain cement concrete cast in situ 1:3:6 type C1 using 20 mm graded stone aggregate as in copings ,hold fast,back filling of pressed steel frame and other similar work water troughs and the like including weathering, slightly rounded or chamfered angles and throating etc including form work complete all as specified and directed by Engineer in Charge.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed by Engineer in Charge.

All as per Ser item No 40 here-in-above before but 150 mm long complete all as specified and directed by Engineer in Charge.

S&F 100mm long Aluminium butt hinges of extruded aluminium alloy with galvanized mild steel hinge , pin anodized complete all as specified

Supply 100mm long mild steel cold rolled butt higes complete all as specified and directed by Engineer in Charge.

S & F extruded aluminium bow handle, fabricated type, anodised 125mm long complete fixed with steel screwscomplete all as specified and directed by Engineer in Charge.

S & F extruded aluminium bow handle, fabricated type, anodised 150mm long complete fixed with steel screws complete all as specified and directed by Engineer in Charge.

S&F Aluminium sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with & including a min of 6 bolts & nuts four on bolt plate & two on staple plate & fixed 250 mm long complete all as specified and directed by Engineer in Charge.

Demolition of brick work built in cement mortar and removing rubbish complete all as specified and directed by Engineer in Charge.

M & L Brick work with fly Ash old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete complete all as specified and directed by Engineer in Charge.

Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc.complete all as specified and directed by Engineer in Charge.

Taking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed by Engineer in Charge.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer in Charge.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer in Charge.

All as per Ser item No 51 here-in-above but refixing old steel tubing complete all as specified and directed by Engineer in Charge.

All as per Ser item No 52 here-in-above but refixing old steel tubing complete all as specified and directed by Engineer in Charge.

M & L for Cutting chases pinning in making good to facing where required for concealed water tubing and making good cutting not exc 10cm girth in brick walls complete all as specified and directed by Engineer in Charge.

S&F in repairs long body 15mm bore bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engineer in Charge.

S & F 15mm Stop valves, fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer in Charge.

S&F CP angle/stop valve long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type complete all as specified and directed by Engineer in Charge.

S&F vitreous china wash basin, white, flat back type of size 580x450mm including brackets including cutting for and pinning in ends of brackets in CM 1:3 including 32mm dia chromium plated waste couplingcomplete all as specified and directed by Engineer in Charge.

S&F pillar taps 15mm bore, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer in Charge.

S&F in repair 32 mm dia of discharge pipe bottel trap of PTMT having minimum water seal of 25 mm .(Minimum weight 32 mm -260 gms/40 mm-270 gms) etc complete all as specified and directed by Engineer in Charge.

S&F 40mm bore PVC low density (LDPE) pipe of pressure 6kg/Cm2 fixed to wall or laid in floor, complete all as specified and directed by Engineer in Charge.

S&F 15mm dia brass chromium plated mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed by Engineer in Charge

S&F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300 gms) complete all as specified and directed by Engineer in Charge.

S&F in repairs brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed by Engineer in Charge.

S&F in repair CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified.complete all as specified and directed by Engineer in Charge.

S&F in repair Soap dish,stainless steel, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer in Charge.

S&F in repair vitreous china squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including p or s trap and provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe etc complete all as specified and directed by Engineer in Charge.

S&F in repairs PVC valveless syphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer in Charge.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides,complete all as specified and directed by Engineer in Charge.

Demolition and breaking up or taking down PVC/AC/CI/SSW 100mm/75mm bore pipe drain pipes, set in cement mortar including PCC haunching and bedding, complete all as specified and directed by Engineer in Charge.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed by Engineer in Charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed by Engineer in Charge.

S&F 110mm bore PVC (SWR) bend, any radius complete all as specified and directed by Engineer in Charge.

S&F 75mm bore PVC (SWR) bend, any radius complete all as specified and directed by Engineer in Charge.

PVC (SWR) junction single (single T), equal or unequal, 75 mm bore, complete all as specified and directed by Engineer in Charge.

PVC (SWR) junction single (single T), equal or unequal, 110 mm bore,complete all as specified and directed by Engineer in Charge.

S&F PVC(SWR) 110mm dia branch piece, single(single Y) equal or enequal complete all as specified and directed by Engineer in Charge.

S&F PVC(SWR) 75mm dia branch piece, single(single Y) equal or enequal complete all as specified and directed by Engineer in Charge.

M&L in repair PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by Engineer in Charge.

S&F PVC(SWR) 75 mm bore floor trap plan with grating including jointing with solvant cement complete all as specified and directed by Engineer in Charge.

S & F for 500 ltr capacity rotational moulded polyethene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position including tank nipple etc all as specified in SSR part I complete all as specified and directed by Engineer in Charge.

Dismantling PVC water tanks and removing for capacity exceeding 250 litres & not exceeding 500 litres etc.complete all as specified and directed by Engineer in Charge.

S&F 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed by Engineer in Charge.

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore, complete all as specified and directed by Engineer in Charge.

S & F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed by Engineer in Charge.

S & F Stainless steel plate rack (utensil rack) of size (600 mm x 750 mm) and depth 300 mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts complete all as specified and directed by Engineer in Charge.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etccomplete all as specified and directed by Engineer in Charge.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 2% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. incl mouldings, chamfers, splay srounded or coved angles, beads,grooves and rebate upto 10 cm in width or 15 cm in girth. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed by Engineer in Charge.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete all as specified and directed by Engineer in Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade over a coat of 3 mm thick white wall care putty , complete, all as specified & directed

M&L for preparation and complete removal of existing treatment from old plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of 3mm thick white wall care putty complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of alkali resistant primer of approved shade/tint complete all as specified.

M&L for preparation & complete removal of existing teatment from old plastered surfaces of wall & applying two coats of cement base paint over a coat o f alkali primer of approved shade over a coat of primer complete all as specified.

M&L for preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete, all as specified.

M&L for preparation and complete removal of old decorated plastered surfaces of ceilling and applying two coat of white washing on ceilling complete all as specified and directed by Engineer-in-Charge.

M&L for preparation and complete removal of old decorated plastered surfaces of wall and applying two coat of white washing on wall complete all as specified and directed by Engineer-in-Charge.

S&F PVC coated 25mm dia anodize aluminium alloy pipe as in curtain rods including brackets and fancy type end knobs, complete, all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, laid bedded and pointed in cement mortar aprons etc

M&L machine cut Kota stone slab flooring 20-25mm thick over 15mm screed bed (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and including granite polish on Kota slab stone all as specified and directed by Engineer-in-charge.

All as per Ser item No 102 here-in-above but on vertical surface such as dado, skirting etc over 10 mm thick skirting in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20mm thick screed in CM 1:4 including cutting, polishing, rubbring & moulding of edges including making hole in granite slab for gas pipe complete all as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situation complete all as directed.

M&L Water proofing treatment on sunken floor consisting of the following operation :- (i) Cleaning of surfaces by wire brushing brooming removing dust particles (ii) M & L PCC 1:2:4 type (B0) using 12.5 mm graded stone aggregate 25 mm thick, finishing the surface even and smooth without using extra cement (iii) Applying two coat of Fosroc Brushbond 2 component POLYMER MODIFIED CEMENTITIOUS water proff coating with proper overlapping when the coating is green all as specified. (iv) Laying of water proof protective layer of cement mortar screed in the ratio of 1:4 15 mm thick mixed with integral water proofing compound Fosroc Conplast WL, finishing the surface even and smooth without using extra cemtent

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even without using etra cement complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L pcc type E2 1:5:10 using 40 mm graded stone aggregate as in sub base complete all as specified and directed

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for incl removing rubbish off the premises complete all as specified and directed.

M/L RCC 1:2:4 type B1 (using 20 mm graded aggrigate)as in slab,beam etc complete.

Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work n.exc 200mm thick

M&L for Formwork torough finished surface edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

M&L 8 to 10mm dia and over TMT bars, cut to length, bent ot shape required, including cranking, bending , hooking ends and binding with and including mild steel wire(annealed not less than 0.9mm dia) icluding welding,rivetting etc complete.

Repairing of RCC projections chajjas, roofs, facia etc by necessary preparation, scrapping, cutting, chiseling, derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC and providing cement concrete (1:1.5:3) using 12.5 mm graded crushed stone aggregate including necessary form work and reinforced with chicken wire mesh and rendering in cement mortar 1:3 using coarse sand in patches area not exceeding 5 sqm each and thickness of RCC member not exceeding 70mm including applying two coats of finishes as provided to the existing surfaces to match with the existing surfaces in at any height complete all as specified and directed.

M&L PPC tiles coloured rubber moulded Paver block any shape and size conforming to IS 15658-2006 of 60mm thickness,M-35 grade in set jointed and pointed with grey cement slurry and pigment to match the floor approved design /colour set and bedded over and including 25mm thick coarse sand laid over compacted sub soil all as specified and directed.

M&L Cement concrete tiles with grey cement and pigment 20cm x 20xm x20mm thick, machine pressed; set, jointed and pointed in net cement slurry in floors, and cut and polished

M&L for preparation of new surfaces of steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide complete all as specified.

M&L for preparation of new surfaces of wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L for preparation of old surfaces of wooden surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

S & F in repair 300mm long Stainless steel six peg hanger chromium plated as approved by engr-in-charge complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for.

S&F in repair PTMT grating 125mm dia withiout waste hole (Minimium weight 40 grams) complete all as specified and directed

Supply & fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long.

S&F in repairs mild steel 300mm, ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed

M&L Water proofing treatment to walls of bathroom consisting of the following operation :- (i) Cleaning of surfaces by wire brushing and removing dust particles (ii) Filling of all brick joints with cement mortar 1:4 (iii) Appling two coat of Fosroc Brushbond 2 component POLYMER MODIFIED CEMENTITIOUS water proff coating with proper overlapping when the coating is green all as specified and sprinkling of coase sand on the surface to make it rough.

M&L for Rolled sections as in cooler stands confirming to Fe290 (gde E-165) complete all as specified and directed by Engineer in Charge.

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing caping/conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade conceal conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all acessories and making good to disturbed conceal surfaces complete all as specified and directed for the following :-

(a) One light/fan/bell point controlled by one switch

(b) One point for socket outlet 5 amps on independent board but not below the switch board in same vertical plane

(c) One point for socket outlet 5 amps on independent board but below the switch board in same vertical /horizontal plane

(d) One point for socket outlet 5 amp same board

(e) One bell/ buzzer point controlled by one push button on the same board with other switches or independent

(f) One 3 pin 15 Amp socket outlet point controlled by one switch using 2.5 sqmm copper conductor cable with continuous earth wire of 2.5 sqmm copper conductor on independent board.

(g) One 3 pin socket outlet. 15 amps, independent, with cables 4 sq. mm size on independent board

S&F in repair ceiling rose surface type bakelite 65x50mm three terminal complete all as specified and directed.

S&F angle/batten type holder insulated body with back plate suitable for light point complete all as specified and directed.

S&F call bell, ding dong type, AC, 230 V, single pole complete all as specified & directed.

S&F switch piano flush type, 5 amps, 230V AC,single pole, one way complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5 amp flush type complete all as specified & directed.

S&F switch piano flush type 16 amps, 230V AC single pole one way complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5 & 15 amp flush type complete all as specified & directed.

S&F fan regulator, 5 stepped, electronic type, single phase, 80 watt, socket size incl connection complete complete all as specified & directed.

S&F bell push piano flush type 5 amp, SP , 230V AC complete all as specified & directed.

S&F in replacement of sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket along with one MCB, single pole of current rating 20 amps, C series 240 volts AC complete all as specified & directed.

Taking down main switches fuse unit, MCB/Kit kat distribution board with steel enclosure along with MCB’s /Kit kat fuse of any amps/ways including wooden board or from steel board and making good disturbed surfaces complete all as specified & directed.

S&F sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole & Neutral, 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole & neutral 40/63 amp, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

Taking down carefully sub main wiring of any nos of wire and size with earth wire on wooden batten/surface conduit/casing caping complete with its all accessories complete all as specified & directed.

M&L for two single core (submain) FRLS PVC insulated cable and one single core green PVC insulated copper conductor earth continuity cable as mentioned below is drawn in and including non metallic, medium duty, rigid PVC conduit not less than 20 mm dia concealed in wall including all conduit and fixing accessories including cutting chases & making good to disturbed surfaces with cement mortar ratio of 1:4 and colour wash complete all as directed. Note :- (I) The cost for cutting, chases required shall deemed to be included in the quoted unit rate. (II) Two run of submain wire, one run of earth wire and one run of PVC conduit shall be measured one RM

(a) 2x4.0 sq. mm + 1x2.5 sq. mm earth wire

(b ) 2x6.0 sq. mm + 1x4.0 sq. mm earth wire

Taking down existing old /worn out tube/CFL/bulk head/sketch light fittings of indoor type fixed on wall of any type/size with its all accessories including lamp complete all as specified & directed

Supply & fixing surface /wall mounted light fitting in CRCA powder coated white housing with pre wired suitable for single T8 LED tube along with supply and fixing one number LED tube in polycarbonate housing of nominal wattage - 18 Watt, Lumen out put - 2100 Lm, Colour Temp - 6500 Kelvin, Size & Length - G13/ T8/ 4 Feet with integral/in built driver, having short circuit and surge protection including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. Cat Part No for batten:- REGALBATTENT8UPTO1X18WDSBSWH of make Havells 'or' IGP161LT8-16 of make Crompton 'or' TMC501 P 1xT-LED 22W P3241 of make Philips or its equivalent as approved Cat Part No for Tubelight:- PHOTANULTRA2.01213T8SSTL18WLED865SPC of make Havells 'or' LTT8-20 of make Crompton 'or' MAS LEDtube 1200MM 18W865 T8 I-2100 lm of make Philips or its equivalent as approved

Supply & fixing energy efficient LED light of 10 Watt of length - 02 Feet long having minimum 1150 Lumen output, wide voltage protection range 140-270 Volt AC housed in extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed. Cat part No: -LUMILINEPLUSSBS10WLED865SPCSS of make Havells 'or' BN 021 LED10S- 6500 PSU GR S1 of make Philips 'or' LDL-10-WW of make Crompton or its equivalent as approved

S&F LED light fitting 10 Watt bulkhead luminaires in high pressure die cast aluminium housing, lumen out put - 700 Lm, colour Temp - 6500 K having Ingress protection - IP 65 fpr dust, water & IK 08 for external impact including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Cat Part No - WT140 LED7S NW PSU S1 PC; Vistaglow of make - Philips 'or' LBHP-10-CDL of make Crompton 'or' LW07-11-XXX-57-XX of make Wipro or its equivalent as approved

Taking down fan, sealing cable end, dismantling blades and removing fan and blades, oiling, greacing and painting of ceiling fans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. incl Hanging and connecting up including provision of cable from ceiling rose or connector to fan as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F (in replacement) bracket for street light made out of 40 mm bore GI pipe medium grade not less than 1.2 mtr length bent at 120 degree to shape fixed on pole/wall with and including 50x6mm FI clamps = 02 Nos with nut bolts, washers including painting of clamps with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Cutting & Chasing required on on brick wall, exceeding 20 CM girth and making good to disturbed surface with cement mortar 1:3 including facing / finishing where as required to match with existing surfaces to recess the MCB DB/sheet steel enclousure complete all as specified and directed.

Cutting & chasing required not exceeding 10 CM girth for concealed conduit wiring and for GI earth wire including making good to disturbed surface with cement mortar 1:3 and distemper / colour wash to match with existing surfaces including facing / finishing where as required complete in all respect as specified and directed.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 all as per manufacture's instructions complete including dismantling all as specified & directed.

M&L for two coats of synthetic enamel paint on steel surfaces, over 10cm in width or grith not other wise described complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI bassed plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed

Supply and fixing of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and as directed.

M&L for PCC 1:4:8 type D2, using 40mm graded stone aggregate, as in foundation filing of manhole/sumps, sub base etc complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block with grey cement and colour pigmentany shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified and as directed.

Supply and fixing Mild steel plates of Fe-290 (Gde E-165), plain or chequered, 5mm thick or over in thickness in available sizes complete all as specified and directed

M&L Earthwork in excavation in foundation in trenches exc 1.5 mt wide and exc 1.5 mt depth in soft/loose soil and getting out complete as all specified and directed by EIC.

Returning filling including spreading levelling watering and well ramrning not exc 25mm thick soft or loose soil complete as all specified and directed by EIC.

Removing excavated material (soil) n.exc 50 mt and depositing where directed at a level n. exc 1.5 mt above the starting point complete as all specified and directed by EIC.

M&L RCC M-25 Design mix using 20mm graded stone aggregate in foundation beams plinth beams bases for columns, etc basement slabs, under reamed piles and mass concrete.

M&L formwork to rough finished flat surface of concrete to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work vertical or to batter complete as all specified and directed.

M&L of mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends binding with and including mild steel wire (annealed) not less than 0.9mm dia securing with clips complete as all specified and directed by EIC.

M&L of mild steel TMT bars 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends binding with and including mild steel wire (annealed) not less than 0.9mm dia securing with clips complete as all specified and directed by EIC.