GE/863/EWS-T-73/2019-20

Amount

Dismantling plain or corrugated steel sheeting (Roof covering) of any description or any gauge or thickness complete all as specified and directed by Engr-in-Charge.

Demolition of brick / block or stone measonry built in cement mortar, complete all as specified and directed by Engr-in-Charge.

Dismantling floor hearth and wall tiles including cement mortar bedding (but not backing) and removing from site complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete terrazo (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level), complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster on brick or stone wall including racking out joints hacking for key scrubbing down with the water etc, complete all as specified and directed by engineer-in-charge.

Dismantling Exc 500 & n exc 1000 water tanks and removing to store complete all as specified and directed by engineer-in-charge.

S&F Rolled sections mild steel Fe -290(Gde E-165) as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed by Engr-in-Charge.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering with self tapping screws complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering with self tapping screwsas in ridge complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S &F Galvanised, corrugated mild steel sheeting 0.63 mm thick, with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in roofs etc. with grade of zink coating 275 in repairs complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

M&L for Pre-cast cement concrete block masonry in 1:3:6 type C1 using 20mm graded stone agg with solid block exc 10cm width and setting in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors set and jointed in neat cement slurry and pointed in colour cement to match the shade of tile over and including 15 mm thick screed bed in CM (1: 6) complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F 300x300x7mm thick glazed ceramic concept tile coloured on vertical surfaces such as skirting, dados, risers to steps etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 10 mm thick cement mortar rendering in CM 1:4 complete all as specified and directed. Approved makes as per Appx 'B' of Tender Pages.

S & F Fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc.complete all as specified and directed by Engr-in-Charge.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floor laid on 15mm thick in CM (1:6) screed bed or bedding layer with grey cement and pigment complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm gradded stone aggreggate as in levelling course of flooring complete all as specified and directed by Engr-in-Charge.

M&L for machine pressed precast interlocking paver block any shape and size conforming to IS -15658-2006 of 80mm thickness M-40 Gde with grey cement and pigment over and including 25mm thick sand cushioning complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

M&L for 50mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection path laid in alternate panels not more than 3mtr in length laid to slope 1:30 including forming joints 10mm wide and upto full depth of PCC and filled with bitumen mastic (1:3) part bitumen 85/25 and 3 parts of sand complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate as in sub base of floor and path, complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats with shutters (without taking off shutters from the frame) and removing from site, area not exceeding 1.5 Sqm each, complete all as specified and directed by Engr-in-Charge.

All as per above item No. 21 but area exceeding 1.5 Sqm but not exceeding 4.0 Sqm each, complete all as specified and directed by Engr-in-Charge.

Taking down of shutters of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm each,complete all as specified and directed by Engr-in-Charge.

S &F 2nd class hard wood Plain, solid, straight chowkats and frames , wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood 35 mm thick plain, framed, panelled shutters (any no of panels) with panels of timber flat on both sides (feather edge) or of veneered partical boaed medium density, wood pertical board with commercial face veneers; supply and fix to chowkats complete all as specified. Approved manufacturer as per Appx 'c' of Tender Pages.

S&F 2nd class hard wood 30 mm thick Glazed and sketon shutters, open rebeated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SS Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkat complete all as specified and directed by Engr-in-Charge.Approved manufacturer as per Appx 'c' of Tender Pages.

S&F solid PVC door frame of size 50 mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, in opening as per specification & drawing in SSR Part-II 2010 section 8. complete all as specified and directed by Engr-in-Charge.Approved manufacturer as per Appx 'c' of Tender Pages.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail on either side and as gap insert for top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to this stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the frame at site as per specification and drawing all as specified in SSR Part-II 2010 section 8.complete all as specified and directed by Engr-in-Charge. Approved manufacturer as per Appx 'c' of Tender Pages.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars, complete all as specified and directed by Engr-in-Charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete glazing bars dovetailed or welded, complete all as specified and directed by Engr-in-Charge.Approved manufacturer as per Appx 'c' of Tender Pages.

S&F 100mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed by Engr-in-Charge.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed by Engr-in-Charge.

S&F 200mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed by Engr-in-Charge.

S&F 140mm floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, complete all as specified and directed by Engr-in-Charge.

S&Fin repairs mild steel 300mm ordinary rat tail rod pattern springs including roller, roller plate, complete all as specified and directed by Engr-in-Charge.

S&F in repairs galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm, complete all as specified and directed by Engr-in-Charge.

M&L for preparing new or previously untreated surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

M&L for preparing new or previously untreated steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

Hacking out old broken glass (any thickness size quality or description) from Wdn or steel frames glazed with putty or fixed with beads, complete all as specified and directed by Engr-in-Charge.

S&F 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in squares area not exceeding 0.5 Sqm in each pane, complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

Taking up or down 15 mm bore GI tubing and connection including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge.

Taking up or down 20 mm bore GI tubing and connection including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge.

Refixing old steel tubing and connection 15 mm bore in new or old position in wall, ceiling and floor etc complete all as specified and directed by Engr-in-Charge.

S&F 15mm medium grade GI steel tubing including all fittings and fixed complete to wall ,ceiling and laid in floor etc complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

Refixing old steel tubing and connection 20 mm bore in new or old position in wall, ceiling and floor etc complete all as directed.

S&F 20mm medium grade GI steel tubing including all fittings and fixed complete to wall ,ceiling and laid in floor etc complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F in repairs 15 mm dia stop cock of cast copper alloy but fancy type chromium plated screwed down high presser with crutch or butter fly handle on both ends for iron pipe or for union fixed complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F Sheet glass shelf assembly consisting of 5.50 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge.

S&F in repairs Bib taps, fancy type CP cast copper alloy with crutch or butter fly handle, screwed down, or secrewed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F in repair 15 mm bore pillar tap, cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F in repair vitreous china squatting pan `Orissa’ pattern, size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with ‘P’ or ‘S’ trap including provision of lime concrete bedding complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F in repairs 10 ltr capacity PVC valve less symphonic action type flushing cistern, white ,with inlet ball valve, float and handle including bracket and 32 mm dia HDPE flush pipe and connected to squat pattern /pedestal pattern water closet at suitable height for smooth functioning complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F PVC connection 15mm bore with PTMT nuts and 750mm long complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

S&F in repair vitreous china wash hand basin, white flat back size 550x400 mm complete including necessary cutting for and pinning in ends of brackets) including brackets and 750mm long PVC waste pipe 32mm bore & waste coupling 32mm dia of PTMT (half or full threaded) complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

S&F 20 mm dia stop cock of copper alloy screwed down high presser with crutch or butter fly handle on both ends for iron pipe or for union fixed in repair complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S&F in repairs 19/20 mm dia curtain rails mild steel chromium plated with fixing brackets, stops, roller etc, complete all as specified and directed by Engr-in-Charge.

S&F rotational moulded polyethylene cylindrical vertical with closed top water storage tank double layered 500 Ltr capacity, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

All as per item No 58 above but of 1000 ltr capacity complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

M&L for 15mm thick rendering in CM (1:4) on external surfaces of brick work finished fair and even complete all as specified and directed by Engr-in-Charge.

M&L for 10mm thick rendering in CM (1:6) on internal surfaces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of cement primer complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

Preparation of new wall surface and applying three coat of White wash complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper over 1mm thick wall care putty on walls, complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

M & L for cleaning of RCC/PVC water tank (underground sump) of cap 5000 ltrs tank 2 Nos and 20,000 Ltrs capacity 2 Nos clear water sump by wire brush and chemicals to remove all algae/ fungi growing on inside water tank surfaces and than white wash the tank surfaces in two coats with freshly burnt fat lime of class 'C' complete all as specified and directed by Engr-in-Charge.

M&L for replacement of filter media (Gravel) of size 40mm grade coarse aggregate of filteration tank including removing of old coarse aggregate from the site complete all as specified and directed by Engineer-In-Charge

M&L for replacement of filter media(Gravel) of size 20 mm grade coarse aggregate of filteration tank including removing of old coarse aggregate from the site complete all as specified and directed by Engineer-In-Charge

M&L for special filter silica sand suitable for water filteration bed complete all as specfied and directed by Engineer-In-charge.

Supply and fixing of street light fitting for 60 watt LED with lens, compact street light fitting with deep drawn MS housing complete with acrylic cover including suitable driver set , and provn PVC of Cable 1.5 Sqmm 3 core approx 1.5 mtr long from fitting to from Ceiling rose to light fitting complete all as specified and directed by Engr-in-Charge. Make: - Crompton Greaves cat part No - LSTP-60-CDL or other equivalent approved makes as in Appx 'B' of tender documents.

Material and labour for pull out the 90 mm HDPE PE100 PN 16 water supply Pipe line from the Span which is of 700 Mtr length hanging between M. Dogri location to Samsung more over Pare-Chu River after care fully disconnection of both ends of pipe line, opening of hanging rings etc, anchoring the other side with and making arrangement for locking of main pipe line with traper machine with suitable size of SWR. complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages. Note: The joint material like clamp set, nuts, bolts, washers will be kept in safe custody for reuse for serviceable and schedule of credit will be paid against the retrieved material

Material and labour for checking the damaged pipe line, replace with new pipe line, making joints, rings and relaying the 90mm HDPE PE100 PN 16 Pipe line on the same span carefully duly making the arrangement for locking and hanging of HDPE 90 mm pipe line with the help of traper machine duly fixed on both side on basement , employment of experienced labour on the site complete all as specified and directed by the Engineer-in-Charge. Approved makes as per Appx 'B' of Tender Pages. Note : The length of new pipe line, joints material etc will be measured and paid separately under relevant items

Material and Labour for laying of HDPE Pipe of Grade PE100 PN 16 of dia 110 mm on surface/ wall including anchoring arrangement complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

Material and labour for laying HDPE Pipe of Grade PE100 PN 16 of dia 90 mm on surface/ wall including anchoring arrangement complete all as specified and directed by Engr-in-Charge.Approved makes as per Appx 'B' of Tender Pages.

Supply and fix of clamps with internal teeth work for jointing the two ends of HDPE pipe PE 100, PN 16 of dia 90mm with the help of HDPE Pipe of dia 110/80mm medium grade GI pipe/ clamp on both ends, including locking arrangment of clamps with each other, nuts, bolts & washer complete all as specified and directed by Engr-in-Charge. Note : The length of the GI tubing medium grade and HDPE pipe 110mm dia shall be measured and paid separately under relevant item

Material and Labour for laying of HDPE Pipe 6 Kg/Sqcm from Water main reservoir to unit area of dia 50 mm on wall/surface/underground making joints and leak proof of pipe line complete all as specified and directed by Engr-in-Charge. Approved makes as in Appx 'B' of tender pages. Note : The excavation of soil will be measured and paid separately under relevent items

Complete all as above ser item No 75 but of dia 40mm

Complete all as above ser item No 75 but of dia 25mm

Supply and fix GI tubing medium grade of dia 80 mm incl necessary fittings. complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

Supply and fix GI tubing medium grade of dia 50mm incl necessary fittings. complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

Supplying, laying Flat type PVC insulated & PVC sheathed industrial cable confirming to IS 7098 (Part-I)-1988, ISI marked for submersible pumps for working voltage upto and including 1100 Volts, cross sectional area of cable 10 Sqmm 3 core.complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

Supply and fix Steel Wire Rope of dia 8 mm for pulling the pipe from span over Pare-Chu River.

S& F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm. complete all as specified and directed by Engr-in-Charge. Approved makes as per Appx 'B' of Tender Pages.

S& F Three phase power contactor 7.5 KW 18 Amp in Motor starter panel as specified. Make :BCH Part No CE15D1N3 or equivalent in approved makes as in Appx 'B' of tender pages.

Supply and fix push button in Motor starter panel all as specified and directed Approved makes as per Appx 'B' of Tender Pages.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 m in depth in a hard/dense soil for laying underground cables/ errection of steel tubular poles / stay pit etc all as directed by Engr-in-charge.

Returning, filling in incl spreading,levelling watering and well ramming in layer n exc 25 cm in soil each layer complete specified and directed by Engr-in-Charge.

Removing excavated surplus material to a distance n.exc 50 m and depositing where directed at a level n exc. 1.5 m above the starting point in any type of soil complete all as specified and directed by Engr-in-Charge.

Net Contract Sum will be after deducting Sch Of Credit of Rs 48349.00

R B TRADERS

akshikconstruction