SPECIAL REPAIRS TO BLDG NO P-124 WG-1 OF ADM AND TRG REGT AT ARTY CENTRE UNDER GE NASIK ROAD CAMP

Amount

Dismantling single layer Mangalore or similar tiles including ridges in roofing all as specified and directed.

Dismantling battens for tiles shingles etc of any size incl tiling fillets spaced exc 15 cm complete alll as specified and directed by Engineer-in-Charge.

S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and making good to wall and roof joint.

S & F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutter, drip and straight flashing.

S & F Rolled mild steel section / tubular section as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and directed

M&L preparing new or old painted steel or iron surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer

M&L for polygonal rubble mesonry, uncoursed well bonded bedded and solidly hearted built in CM 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, Hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 40mm as specified, of random rubble walling,uncoursed or brought upto courses

M&L for keyed pointing of CM 1:4 to random or polygonal rubble;uncoursed or brought upto courses complete all as specified and directed.

Dismantling of stone slabs & tiles of any description or thickness (except ceramic tiles) in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed

M/L Screed bed or bedding layer of cement mortar 20 mm thick for laying floors finishes in cement mortar 1:6.

M&L for machine cut kota stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.(Note: screed bed or bedding layer measured and paid seperately )

M & L Kota stone slab 20-25 mm thick in riser of steps , dado and pillar laid and jointed with grey cement slurry with pigment to match the shed of the slab incl rubbing and polishing complete all as specified and directed. (Note: Backing coat shall measured and paid seperately )

S & F machine cut cudappa stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete (Note: screed bed or bedding layer measured and paid seperately )

M&L granite (of any type)work (table rubbed and polished) 20 mm thick in steps, jambs,pillars, cooking platforms and like set in cement mortar 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillers etc but including ashlar facings, dressed stone work and precast concrete articles

M&L Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 with old size bricks.

M&L Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 with old size bricks.

Taking down cement plaster on brick or stone wall etc including raking out joints hacking for keys scrubbing down with water etc. including removing all the debris out side MD land

M&L for rendering 5 mm thick (1: 3) on fair faces of concrete surfaces incl preparation to new surfaces on ceilings finished even and smooth without using extra cement

M&L for rendering 15 mm thick on than fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement adding water proofing compound 3% by weight of cement (water proofing compound shall be measured and paid separately)

M&L for rendering 15 mm thick in cement mortar 1: 6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement incl Sagol finish complete all as specified and directed

Supply only intergral water proofing compound

M&L Preparation of new plastered surfaces and applying three coats of white wash on ceiling surfaces all as directed

M&L for cleaning of existing wall surfaces including preparation by brooming down plastered/unplastered surfaces complete and applying two coats of acrylic weather proof exterior paint over a coat primer( Make : APEX of Asian Paint or equivalent) complete all as specified ad directed

M&L for preparing New plastered surfaces and applying two coats of distemper oil emulsion over a priming coat of chalk whiting on plastered surfaces preparatory to distempering of walls.

S&F in repair stainless steel sink made of stainless steel 1mm thick with out drainage board including plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing contilever brackets and connecting union to pipe overall size 495mm x 420mm, bowl size 410mmx330mmx160mm complete all as specifed and directed

Dismantling wall and ceiling boards( Fibre, pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified & directed.

S&F interlocking aluminium powder coated snap grid consists of main Tee runners of size 38mm x 25mm x 1.00 mm spaced 1200mm centre to centre and cross Tee of size 25mm x 25mm x1.00mm, 1200 long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mm x 600mm and provide a secondary cross Te 25mm x 25mm x 1.4mm (of length 600mm) to be interlocked of the centre of 1200mm x 600mm panel to form a grid of 600mm x 600mm and wall angle 25mm x 25mm x 1.5mm . Aluminium alloy extruded section shall be aluminium anodized ( minimum 15 micron) and shall conform to IS 733, IS 1285 and IS 737, and providing and fixing with Hangers of 4mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long size of grid 600 x 600mm complete all as specified and S&F non asbestos cement building board 4mm thick of make E board classic of M/s Everest industries Ltd or equivalent make as approved, “in ceiling fixed with screw as per manufacturer instruction”

M & L for special treatment to sunken portion with 10mm thick plaster in CM 1:4 with WPC liquid complast 421 and applying one coat each of Nitopro of 100 & Nitproof 120 on plastered surface. Rendering again 10mm thick plast in CM 1:4 mixed with complast 421 in sunken portion of WC & CI pipe joint shall be filled/jointed with mixture of cement fine sand and Nitoproof 130 and provide hole in the wall & fix 600mm long 20mm dia GI spouts light grade & 1:3:6 C2 filling, floor area of WC upto 1.5 Sqm etc complete all as specified and directed.

S&F Vitreous china squatting pan ,'Orissa' pattern, size 580x440 mm white,with integral foot rests (excluding flushing cistern and flush pipe)

S&F of PVC(SWR) 'P' trap of 125/110 mm bore

Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises.

M&L for 15 mm thick rendering in cement mortar 1:4 on brick masonary or concrete rough finished surfaces as backing coat

M&L for coloured glazed ceramic tiles 300 x 450 x 7-8mm thick in vertical surface, set and jointed in neat cement slurry & pointed with white or coloured cement to match

M & L for 15mm thick Screed bed or bedding layer in cement mortar 1:6 for laying floors finishes

M&L non-skid coloured ceramic tiles 7 to 8mm thick square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile all as specified and directed by Engineer-in-Charge

S&F in repairs bib taps standared of PTMT 15mm bore dia any colour high presure screwed for iron pipe of Make Prayag fixed and repairs (minimum weight 90 gms) complete all as specified and directed

S & F PVC connections 15mm size with PTMT nuts of length 300mm.

S&F in repair stop valve, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed

Taking up or down tubes galvanized iron and connections and fittings or removal from site as incl cleaning for refixing where directed complete all as specified and directed.

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

Re-fixing only tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixing new fittings such as socket, bends, elbows nipple, union etc all as specified and directed of size complete all as specified and directed

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

S/F for tubes medium grade, galvanized with iron all fittings fixed to walls, ceiling and laid in floor of sizes complete all as specified and directed :-

(a) 15 mm dia

(b) 20 mm dia

(c) 25 mm dia

S&F of PVC(SWR) pipes single socketed,in any length with rubber ring joints fixed to walls

(a) 75 mm dia

(b) 110 mm dia

S&F of PVC(SWR) bends of any radius

(a) 75 mm dia

(b) 110 mm dia

S&F of PVC(SWR) branch piece,single(single Y) equal or unequal

(a) 75 mm dia

(b) 110 mm dia

S&F of PVC(SWR) junction single,(single T),equal or unequal

(a) 75 mm dia

(a) 110 mm dia

S&F of PVC(SWR) Vent cowl

(a) 110 mm dia

(a) 75 mm dia

S&F 50mm dia low density polyethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to walls as directed by Engineer-in-Charge

S & F PVC (SWR) 75 mm dia floor trap plain with grating incl jointing with solvent cement

S & F Vitreous china half stall type white with grating spreader & union and discharge pipe line complete incl providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plug with and incl 60 mm long brass screws pointing around urinal back in cement fixing spreader flush pipe and union for discharge pipe all as specified and directed by Engineer in charge

S & F waste coupling of 40 mm bore (half or full threaded) suitable for urinals

Taking down carefully existing bitumen tarfelt incl. Screed and cleaning of surfaces of roof etc. With wire brush incl. Flashing and junctions of parapets/kerb walls etc. And removing of the rubbish to a distance exc. 500 metres but not exc. 1.5 km and deposting where directed.

M&Lfor screed bed or bedding layer 15mm thick in cement mortar (1:4) on concrete surfaces mixed with water proofing liquid and smooth finished and smooth(without using extra cement). (WPC paid and measured saperately).

Waterproofing on roof including flashing and junction of parapet, kerb, wall etc. As under (a) Applying bituminous primer on cleaned and dried surface @ 0.2 kg/sqm. (b) A coat of hot blown type bitumen of grade 85/25, applied hot @ 2.25 kg/sqm (c) Laying by thermo fusion ( torch applied) 3 mm thick APP based polymeric water proofing membrane weighing not less than 3.5kg/sqm and reinforcement with polyester non woven fabric ( not less than 150 gms/sqm) (d) Painting the exposed APP membrane surface with bituminous paint @ 0.15kg/sqm

Taking down chowkat or frames with shutters (without taking off shutters from the frame not exc. 1.5 Sqm each.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube S&F in opening as per specification and drawing.

S&F factory made soild panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing.

S&F MS butt hinges 100mm size medium weight complete all as specified and directed

S&F aluminium alloy barrel tower bolt 150 mm long

S&F 150 mm aluminium alloy handels cast/plate type

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc.

Taking down unservicable/partly servicable light fittings any type, tube light fitting and fixtures, etc, and making good to the disturbed surfaces of walls/floor etc to macth with existing surfaces including white washing/colour washing/distempering to match with existing wall/floor/ceiling finishes.

Dismantling unserviceable main switch/DBs/MCB incl wooden board and deposit to MES store yard including making good disturbed surface of wall

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces.

Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing capping not less then 20 mm width with MS sheet metal sunken switch/Terminal box 1.2 mm thick and ebonite switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface all as directed and specified.

(a) One light point controlled by one, one way switch

(b) One ceiling /exhaust fan point controlled by one switch and regulator

(c) One 3 pin 5 amp socket out point on the same board with other switches.

(d) One3 pin 5 amps socket out let point on independent board

(e) One light point controlled by two 2-way switches, with cables 1.5 sq. mm size

All as per same in item No 68 above but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 1.5 Sq.mm. earth wire.

S &F Switch piano flush type single pole one way 5 amps.

S &F Switch piano flush type single pole two way 5 amps.

S &F Socket out let 2 in one, 5/3 pin 5Amp

S &F Switch socket combination 5 Amps 5 pin flush type

S &F Switch socket combination 5 in 1, 5 pin 5/15 Amps flush type universal .

S &F Ceiling rose, surface bakelite 65x50 mm three terminal

S &F Electronic regulator 100/120 Watt step type

S &F Lamp holder insulated body with back plate for angle holder all as per specified.

S & F 1x 18 watt universal batten for T5 and T8 lamps as regal batten for LED tube. Make Havells Cat No: REGALBATTENT8UPTO1X22WDSBSWH or eqvt in Crompton/Bajaj/Philips

S & F Ultra bright glass 18W LED tubelight with very high efficacy suited for installation in existing T8 fitting with G13 lamp holders as crystal glass LED Tubelight (Double Side Connection). Make Havells Cat No: CRYSTAL 1213T8DSTL18WLED865SGLASS or eqvt in Crompton/Bajaj/Philips

Supply & fix Exhaust fan 450 mm sweep heavy duty including 3 core copper cable & cutting holes/ circular opening in brick, stone wall and making good to disturbed surfaces if required etc, complete all as specified and directed by Engr-in-Charge. Make - Havells Cat Part No-Turbojet SP 1400 RPM or eqvt in Crompton/Bajaj/Philips

S &F energy saving and environmental friendly long life 1X15 Watt LED street/security light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistance of IK07, complete all as specified of make- Havells Cat No-ENDURAPEARLSL15WLED757SASYTOPC or eqvt in Bajaj/C&S/Crompton

Fabrication,supply & fixing of GI pipe bracket up to 40 mm dia- 0.9m long & 2 set of clamps made out of 30x5mm ms flat & fixed with anchor bolt suitable for 1x15 w LED security light fitting

S & F MCCB DB Vertical type made of sheet steel enclosure 4 way 415 volts TPN double door with detachable gland plates for flush / surface mounting with busbar, neutral link with earth bar complete all as specified and directed. Make : Legrand, Cat part No. 507725 or eqvt in Havells/Standard/L&T

MCB DB made of sheet steel , powder painted with NUTRAL bus bar 200 A, neutral link, earth bar and Din rail , 240Volts SPN with 8 way Double door , IP-43-IK09 protection grade. Make : Legrand/Havells/Standard/L&T

MCB DB made of sheet steel, powder painted with bus bar 200 A, neutral link, earth bar and Din rail , 240 Volts SPN with 4 way Double door IP-43-IK09 protection grade, Make : Legrand/Havells/Standard/L&T

S & F MCCB TPN 100Amps , 415Volts, 25KA ,4 pole. Make - Legrand/Havells/Standard/L&T

S&F MCB, single pole and neutral, 240 Volts , 40-63 Amps all as specified and as directed. Make : Legrand/Havells/Standard/L&T

S&F MCB single pole 240 Volts , 6 to 32 Amps all as specified and as directed. Make : Legrand/Havells/Standard/L&T

S&F MCB single pole 240 Volts ,40 to 63 Amps all as specified and as directed. Make : Legrand/Havells/Standard/L&T

Taking down and refixing the ceiling fan/exhaust fan of any size and sweep in proper manner and making connection withT 3 core copper cable including painting all as per specified and directed by Engr-in-Charge

Sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC Casing Capping not less then 32mm dia medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge.Notes:- (i)Two wires of 6 sqmm and one wire of 4 sqmm and one run of PVC casing/caping shall be measured as one unit.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in gound (Earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connecting to the galvanised iron earth lead wire of 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and earht strip protected by provision of GI light grade pipe 15 mm light grade bore including provision of pit in PCC (1:2:4) type B-1 using 20 mm graded of stone aggregate with PCC cover including 20mm bore pipe for wetering perforated at bottom 1.75 mtr long placed on top edge of earth plate common salt and charcoal (not less than 40 Kgs, 80 Kgs each) filling with fixing arrangement funnel wire mesh and earth work in hard dense soil returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electircal plate No 03 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion.

M/s. JBSR ENTERPRISES.

Alpha Construction

RELIANCE ELECTRONICS

M/S MANISH CONSTRUCTION CO

M/S G.S RAWAL

K P Enterprises

M/S YOGESH CONSTRUCTION

Vinod Enterprises

DEVA CONSTRUCTION