Sectional Signalling Maintenance Contract in section of SSE/Sig/RRI/CNB for period of Twenty Four Months.

Description:- Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003, issued vide RDSO document No. RDSO/SI/G/2010 Version 1.1 dated 04.02.2014 or latest, alongside the track in normal soil/strata (including soft rock), conforming to distances as per cable route plan and refilling and

trench by loose soil for a layer of 50mm thickness approximately before covering by bricks (supply of bricks shall be covered under different Sch. item). The work shall be done as per the extant practice on North Central Railway and instructions of Railway Engineer at site. In case 1.2 m depth of trench is not achievable due to site conditions, specific approval of JAG/SG Officer will be required for each site where trench depth of 1.2m is not possible, only after approval of JAG/SG Officer proportionate payment can be done.( Inspection By Consignee).

Description:- Horizontal Boring/Manual moling without damage to surface road /track for laying/insertion of DWC/GI/HDPE pipe. The bore shall be done at the depth of minimum 1400 mm from the ground level. The ground level shall be considered ignoring the bank height of the bank of

material required for work and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. Payment of boring shall be made only after DWC/HDPE/GI pipe is laid in the bore. (Inspection by Consignee ).

Description:- Removal of Rail (13m) in the way of cable route trench, signal/location box

The obstruction will be removed by the contractor for ensuring proper execution of related works. (Inspection by Consignee ).

PRAYAGRAJ DIVISION-S AND T/NORTH CENTRAL RLY

signal/location box foundation, track crossing etc. These obstruction will be removed by the contractor for ensuring proper execution of related works. (Inspection by Consignee )

cables. (Inspection by Consignee )

Description:- Laying of S&T Cables of various cores/ pairs/ quads in trenches/ GI pipes/ RCC pipes/ DWC pipes etc. as per the site requirement and as per approved cable route plan. This also includes

laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes.(Inspection by Consignee )

Description:- Refixing of electrical point machine, ground connection during phase working after

commissioning of electrically operated point, fixing and connecting point indicator on derail switch if necessary. The work shall be done as per extant practice on NCR and the instruction of Railway Engineer at site. (Inspection by Consignee )

Description:- Shifting of existing full location boxes coming in the alignment of new line. The work includes losing & removal of soil around location boxes by excavating soil around foundation, making of pit for shifting of location box horizontally opposite to railway track up to 0.5 to 1.0 mtr.

filled after shifting of Location Boxes Location box shall be shifted by push method with the help of jacks or by crane by contractors own expenditure under instructions of engineer in-charge at site. The work may affect train working hence the work shall be done as per margin only or during traffic block only.(Inspection by Consignee )

Description:- Shifting of existing half location boxes coming in the alignment of new line. The work includes losing & removal of soil around location boxes by excavating soil around foundation, making of pit for shifting of location box horizontally opposite to railway This includes loosing of

Location Boxes. Location box shall be shifted by push method with the help of jacks or by crane by contractors own expenditure under instructions of engineer in-charge at site. The work may affect train working hence the work shall be done as per margin only or during traffic block.(Inspection by Consignee )

Description:- Supply, fabrication and fixing of retro-reflective marker/boards/plates as per the

per Drg. no.SA-23459-60 (Adv), 'A' marker - Illuminated as per Drg. no.SA-23461(Adv), 'G' marker - Non illuminated as per Drg. no. SA-23477(Adv) or as applicable and provided by Railways. (Inspection by Consignee )

Description:- Supply, fabrication and fixing of the Calling On board/BSLB board as per RDSO Drg.

foundation and painting with Retro reflective paint. All work to be carried out as per Railway site engineer instructions.(Inspection by Consignee )

No. TYP/14/0014 dtd 28.11.2014 issued vide NCR LOA no. S&T/NCR/DRG/TYP dated 28.11.2014,on signal post with contractor's own material like clamp, U bolts, nuts etc.(Inspection by Consignee )

Complex/under the existing running rod or any other Signalling installation.(Inspection by Consignee ) Per

Conductor Description:- Termination of Outdoor Cables (Main Cables /tail cables) at ARA/Disconnect type

generator room etc. The item includes dressing of cables and wires with dressing threads as per standard practice. All material required for this item will be supplied by contractor. The outdoor cable shall be terminated in Relay Room, DG Room, ASM Room etc under supervision and instructions issued by Engineer incharge of the work. (Inspection by Consignee )

PRAYAGRAJ DIVISION-S AND T/NORTH CENTRAL RLY Description:- Excavation, casting, curing of foundation and Installation and Erection of Apparatus case Full (Apparatus Case as per RDSO drg. No. RDSO/S-11500 or latest) with contractor's own

Apparatus case. Th is includes filling of location foundations with river bed sand and plastering on top with a mixture of 1:4 of cement and sand. It covers fixing of lamp holder, switch and lamp etc. in Apparatus Case. Foundation shall be done as per Drawing no AGC/Full loc/2023/01(Inspection by Consignee )

Description:- Fabrication and fixing of phenolic laminated sheet of grade P3, minimum 10 mm thick, as per Apparatus case diagram/plan, in location box by providing all fixtures like

coated string rods at the back side for cable support with contractor's own material like iron angle, nuts, bolts etc. The iron angle for fixing shall be minimum 3 mm thick. This also includes fixing of teak wood shelf minimum 25 mm thick for holding track circuit equipments. The work shall be done as per instructions of Rly engineer at site. (Apparatus case Full.(Inspection by Consignee )

Description:- Fixing of ARA(M-6) Terminals /Screw less connectors / modular disconnect terminal

This includes provision of two additional holes on the board on either side for cable conductor entry. The work shall be carried out as per instructions of railway Engineer incharge. (Supply of all above terminals has been covered separately)(Inspection by Consignee )

Description:- Supply and installation of earth electrode as per standard practice and as per NCR Drawing No. S&T/CONST/6.4/97. It includes supply of GI pipe of 3 meter length. It includes connecting the earth electrode to the equipments which are required to be earthed including digging

cover (cover as per drawing No. S&T/CONST/6.3/97. It includes installation of 7 strand GI wires as earth lead wires, supported on MS fl at size 5mm x 40 mm, soldering and nut bolt both, one end of both earth lead wire and MS flat to earth electrode and other end to Location boxes, block equipments, power equipments, cable sheath, signals etc. as per site requirement and as per instructions given by engineer incharge.(Inspection by Consignee )

Description:- Cement concrete work for miscellaneous, unscheduled items in ratio 1:3:6 of cement,

plastering with cement and sand mixture in ratio 1:4 (aggregate will not exceed beyond 3.8 cm). The aggregate cement and sand will be supplied by contractor.(Inspection by Consignee )

Description:- Painting of two coats of Enamel paint over one coat of Red Oxide primer after

App. Cases inside and outside to be done by Silver colour. (Apparatus Case Full) (Inspection by Consignee )

Description:- Painting of two coats of Enamel paint over one coat of Red Oxide primer after

App. Cases inside and outside to be done by Silver colour. (Apparatus Case Half)(Inspection by Consignee)

scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar. (Main Signal post, base, unit and complete fittings)(Inspection by Consignee)

scrapping and cleaning of the surface. Paint to be of reputed make Asian/Dulux/Berger or similar. (Shunt Signal post, base, unit and complete fittings)(Inspection by Consignee)

Description:- Painting of two coats of Enamel paint over one coat of Red Oxide primer after

(Point machine and ground connections, Point machine by Black enamel and ground connection by Red oxide)(Inspection by Consignee)

Description:- Hiring of JCB/Hydra/ Poclain machine (in good working condition) for levelling & dressing of ground/ dismantling structures including disposal of debris through dumpers/Shifting the

machine operator, fuel etc. Payment shall be made for actual working hrs. at site & proportionate payment to be made in case less than hours. .(Inspection by Consignee) PRAYAGRAJ DIVISION-S AND T/NORTH CENTRAL RLY

TLJBs, Block joints etc. Each item to be taken as one unit. (Inspection by Consignee )

other associated S&T fittings. All the released material will be transported to the SSE/Consignee depot. (Inspection by Consignee )

etc.) during Rolling Block/Disconnections/NI Note: Contactor/Firm should provide sufficient Manpower with Workable tools & Equipments. (Inspection By Consignee) LOT =Per Gear.

Description:- Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No RDSO/ SPN/ 197 Ver. 1.0 or latest to achieve a resistance less than 1 ohm. It consist of following: [a] Copper bonded steel electrode of minimum 3.0 meter long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 no. [b] Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. [c] Copper strip of 150 x

Copper strip of 150 x 25 x 6 mm [SEEB] = 1 no. [f] Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS : 694 for connecting main earth electrode to MEEB in the equipment room in duplicate. [minimum 10 meter] [g] Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS : 694 for connecting MEEB to SEEB and SPD to MEEB [minimum 10 meter ] [h] Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS : 694 for connecting various equipments to SEEB [i] Supply of copper lug sleeve for 3/16 cable.(Inspection by RDSO).

Description:- Installation of Unit Maintenance Free Earth to achieve a resistance less than 1 ohm as supplied under item no. 13002 of Chapter 13 of SOR. It includes- [i] Digging the earth to the required depth. [ii] Insertion of electrode. [iii] Filling of earth enhancing compound [Approx.30 Kg] [iv] Provision of exothermic weld connections to copper tape of 25 mm x 6 mm x 150 mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. [v] This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3 inch thickness. [vi] Cables 35 Sq mm/ 16 Sq mm/10 sq mm for connecting earth to busbar, busbar to busbar and busbars to various equipments. Earth electrode of 17.20 mm dia and 3.00 meter long high tensile low carbon steel circular rods molecularly bonded with copper and outer surface [minimum copper

or latest. [vii] Copper strips of 150 mm x 25 mm x 6 mm to be welded with each earth electrode, copper strips of 300 mm x 25 mm x 6 mm for main equip- potential busbar, copper strips of 150 mm x 25 mm x 6 mm sub equip-potential busbar in relay room, power room and panel room. [viii] GI strip 25 mm x 2 mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300 mm x 300 mm x 300 mm [Inside dimension] of approximate 50 mm thick with pulling hooks to cover the earth pits. Note : The installation of this item shall be carried out by the contractor as per RDSO Specn.No.RDSO/SPN/ 197 Ver 1.0 or latest. Typical RDSO approved drawings referred in the RDSO specification document are : [i] SDO/RDSO/E&B/001 for typical installation of Earth, [ii] SDO/RDSO/E&B/002 for typical bondong and earthing connections, [iii] SDO/RDSO/E&B/003 for typical arrangement for earth resistance measurements.(Inspection by Consignee )

as per Drawing No. RDSO/S-3592 (1No.), RDSO/S-3593 (1 No.),S-23199 (2 No.), S-8640 (4 No.),S-

S.No. Item Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Amount Bidding Code Unit Above/ Schedule () 002-NS Item 6214907.63 Below/P ar NS 200.00 cum 84.23 16846.00 AT Par 16846.00 Description:- Earth work around location boxes signals etc Where necessary including 50m lead & 1.5 lift by excavation .The leads be measured from the centre of gravity of excavation to the centre

levelling & dressing. The earth work around the location/junction boxes shall be up to the plaster level and for width sufficient for the maintainer to attend the box both from front and back side. (Inspection by Consignee) NS 500.00 Sqm 81.08 40540.00 AT Par 40540.00 2 PRAYAGRAJ DIVISION-S AND T/NORTH CENTRAL RLY 2 Description:- Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 13.92.1 Old work (one or more coats) (Inspection by Consignee) NS 10.00 Numbers 1232.87 12328.70 AT Par 12328.70 Description:- Painting two coats of synthetic enamel paint over one coat of Red Oxide primer on the following after scrapping and cleaning of the surface wherever necessary with contractor's own

of Railway representative at site. Primer and paints to be used by contractor should be both of Asian Paints make. electrical lifting barrier booms complete with pedestal box both side. (Inspection by Consignee) NS 10.00 Numbers 863.00 8630.00 AT Par 8630.00 Description:- Painting two coats of synthetic enamel paint over one coat of Red Oxide primer on the following after scrapping and cleaning of the surface wherever necessary with contractor's own

of Railway representative at site. Primer and paints to be used by contractor should be both of Asian Paints make. Painting of sliding booms complete with pedastal box both side (Inspection by Consignee) NS 2.00 Numbers 3849.09 7698.18 AT Par 7698.18

with rubber tyre, measure forward & amp; Backward, Telescopic handle, Precision measuring wheel .Make/Brand: Stanley or Bosch or JCB or Freeman or Equivalent.(Inspection by Consignee ) NS 3.00 Numbers 103309.00 309927.00 AT Par 309927.00 Description:- Supply of battery operated Rail Core Drill machine (Eibenstock Make ERD35-2-V50.4 B or similar) as per RDSO specification no. TM/SM/468 dated 31.03.2014 First Revision, 2017 or

drill bit for sizes 7.2 mm (Solid drill), 13 mm (Rail HSS Cutter), 14mm (Rail HSS Cutter), 16mm (Rail TCT Cutter), 22 mm (Rail TCT Cutter) to be included as standard accessory in each machine. (Inspection by Consignee ) NS 3.00 Numbers 132113.52 396340.56 AT Par 396340.56 Description:- Supply of Track maintenance tools and accessories ,as Light weight Rail Drilling

RATTLER, make Broach Cutter Drilling Machine Pvt. Ltd or similar/superior along with all accessories and drill bits. (Inspection by Consignee ) NS 25.00 Numbers 64324.09 1608102.25 AT Par 1608102.25

Connection) set for TWS electric point machine(RDSO Type) as applicable. (Inspection by RITES) NS 10.00 Numbers 1568.06 15680.60 AT Par 15680.60

suitable for 230 volts, 50 Hz A C supply, 1440 RPM heavy duty with wiring and flexible PVC pipe as required. Make: Almonard, Bajaj, Havell's, RR or similar.(Inspection by Consignee ) NS 5.00 Numbers 5468.58 27342.90 AT Par 27342.90 Description:- Supply of CO2 type fire extinguisher capacity 4.5 Kg capacity ISI marked, with all

pipe fitted with PVC bend horn, with carrying handle and wall mounting bracket, complete in all respect. It should conform to IS2878:2004. Extinguisher certificate has to be supplied along with the item. .(Inspection by Consignee ) NS 50.00 Kg 84.60 4230.00 AT Par 4230.00

SpecificationNo.IS:279/81 or Latest. (Inspection by Consignee ) NS 25.00 Numbers 477.34 11933.50 AT Par 11933.50

for the job such as E type lock , MS angle, Nut and bolt etc. will be supplied by contractor as per RDSO DRGNO-SA 33763377 & IRS-S-30/64.(Inspection by Consignee ) NS 2.00 Numbers 50762.53 101525.06 AT Par 101525.06 Description:- Recharging for DM plant as capable Strong Acid cation 200 liters strong base anion

strong base anion 01 No hydrochloric acid 50 Kgs caustic soda 25 Kgs treated water TDS -: Less than

NS 50.00 Numbers 1534.37 76718.50 AT Par 76718.50 PRAYAGRAJ DIVISION-S AND T/NORTH CENTRAL RLY

Reinforced Plastic Drg. SI-10272ALT-1 as per Specn. No. IRS.S-10/78 with latest amendment. PBT terminals are to be supplied by the contractor. The angles for fixing TLJB are to be supplied by the contractor with all allied materials of Track Lead Junction Box made of fibre glass (FRP) asper Drg. No. SI 10277 Alt-1 fitted with four (04) nos. PBT terminals with disconnecting facility. FRP should be as per RDSO Specification No. RDSO/SPN/151/1997 with latest amendment. The track lead junction box should be fitted with an iron angle of size 50mm/50mm, Length 01 (One) mtr. & Thickness 05(five) mm with 02 (two) nuts & bolts of size 10mm and 50mm by drilling holes. Lower portion of iron angle to be cut and bend & to be buried in the earth up to 0.7mts. (Inspection by Consignee ) NS 100.00 Lot 147.29 14729.00 AT Par 14729.00 Description:- Charging of Low Maintenance Lead Acid batteries with contractor's own battery grade Sulphuric Acid and distilled water with minimum two charge- discharge cycles. Installation of

Rly & as per instructions of Rly representative at site. The Sulphuric acid & Distilled water to be used for charging shall conform to specification Is-266-1961 & IS1070-1960 respectively.(Inspection by Consignee) LOT=Per 100 VAH (Inspection By Consignee ) NS 10.00 Numbers 45238.34 452383.40 AT Par 452383.40

39A/Motwane or similar. (Inspection By Consignee) NS 10.00 Numbers 10625.27 106252.70 AT Par 106252.70

BLUE STAR or Similar. dt.07/05/2025) (Inspection by Consignee) NS 600.00 Numbers 194.07 116442.00 AT Par 116442.00

earthing to be done).Insp. (Nos=Per cable) (Inspection by Consignee) NS 4.00 Numbers 33000.00 132000.00 AT Par 132000.00 Description:- Provision of one time repair & service of DG Set of 125 KVA Cummins Make installed

filter Kit, Change of coolant, Change of Mobil oil & Service charge. All the tools for repair & service manpower, transportation to be brought by contractor. (Inspection by Consignee) NS 100.00 Sqm 1092.38 109238.00 AT Par 109238.00 Description:- Providing and fixing permanently colour coated trapezoidal profiled sheet of depth 28-30 mm at 195-205 mm pitch distance with precisely engineered " Rib & Flute " design . Profilled

galvalume steel sheet (550 mpa yield strength ) having a coating of mass of 150 gsm zinc- aluminium coating AZ-150 total on both side as per , AS 1397:1993 finished with 20 microns approved colour coating of Silicon Modified Polyester (SMP) / Super Polyester paint coat on exposed surface. (Inspection by Consignee). NS 500.00 Sheet 11.18 5590.00 AT Par 5590.00

(EPM) with cover. One booklet both side printing page 20 Nos (Size:-7 inch length and 5 inch width). (Inspection by Consignee). NS 600.00 Numbers 57.60 34560.00 AT Par 34560.00

booklet both side printing page 20 Nos with cover(Size:-7 inch length and 5 inch width). (Inspection by Consignee). NS 600.00 Numbers 57.60 34560.00 AT Par 34560.00

One booklet both side printing page 20 Nos with cover (Size:-7 inch length and 5 inch width). (Inspection by Consignee). NS 200.00 Numbers 57.60 11520.00 AT Par 11520.00

booklet both side printing page 20 Nos with cover(Size:-7 inch length and 5 inch width). (Inspection by Consignee). NS 100.00 Numbers 57.60 5760.00 AT Par 5760.00 PRAYAGRAJ DIVISION-S AND T/NORTH CENTRAL RLY

booklet both side printing page 20 Nos with cover (Size:-7 inch length and 5 inch width). (Inspection by Consignee). NS 400.00 Numbers 57.60 23040.00 AT Par 23040.00

booklet both side printing page 20 Nos with cover (Size:-7 inch length and 5 inch width). (Inspection by Consignee). NS 225.00 Numbers 162.72 36612.00 AT Par 36612.00

section of SSE/Sig/RRI/CNB . (Inspection by Consignee ) NS 30.00 Numbers 4322.25 129667.50 AT Par 129667.50

of SSE/Sig/RRI/CNB as per Annexure-A Number = 10 SMC Record Register (Inspection by Consignee) NS 100.00 Lot 2464.01 246401.00 AT Par 246401.00

etc. and sealing of cable entry pit etc. as per Technical specifications, complete with contractors's material.(Inspection by Consignee ) Lot = Per Location NS 25.00 Sqm 1303.02 32575.50 AT Par 32575.50

HIGH GLASS RETRO REFLECTIVE ACRYLIC SHEET WITH PERMANENT PRESSURE SENSITIVE ADHESIVE. MAKE AVERY, 3M, KIWA OR SIMILAR.(Inspection By Consignee). NS 25.00 Sqm 1303.02 32575.50 AT Par 32575.50

HIGH GLASS RETRO REFLECTIVE ACRYLIC SHEET WITH PERMANENT PRESSURE SENSITIVE ADHESIVE. MAKE- AVERY,3M, KIWA OR SIMILAR.(Inspection By Consignee). NS 25.00 Sqm 1303.02 32575.50 AT Par 32575.50

HIGH GLASS RETRO REFLECTIVE ACRYLIC SHEET WITH PERMANENT PRESSURE SENSITIVE ADHESIVE. MAKEAVERY, 3M, KIWA OR SIMILAR.(Inspection By Consignee). NS 25.00 Sqm 1303.02 32575.50 AT Par 32575.50

HIGH GLASS RETRO REFLECTIVE ACRYLIC SHEET WITH PERMANENT PRESSURE SENSITIVE ADHESIVE. MAKE AVERY, 3M, KIWA OR SIMILAR.(Inspection By Consignee). NS 25.00 Sqm 1303.02 32575.50 AT Par 32575.50

HIGH GLASS RETRO REFLECTIVE ACRYLIC SHEET WITH PERMANENT PRESSURE SENSITIVE ADHESIVE. MAKE AVERY, 3M, KIWA OR SIMILAR.(Inspection By Consignee). NS 75.00 Set 3300.00 247500.00 AT Par 247500.00 Description:- Repairing of S-Bonds of size (11, 16, 20.5 & 21.5 Mtr.) long for Seimens make Audio

(32 mm dia 94 mm length one side 20 mm hole and one side 16 mm x 43 mm thread position) (b) IS

Consignee) NS 1000.00 Kg 157.95 157950.00 AT Par 157950.00 Description:- Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing

required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. (Inspection .By Consignee) NS 50.00 Set 4100.00 205000.00 AT Par 205000.00 Description:- Erection of fencing unit complete should comply with the item includes foundation fabrication & fixing of fencing unit. Fixing material such as rivets, nut bolts washer or any machine and tools will be supplied by the contractor. The team to be provided for this work should comprise

coat of Red Oxide primer on the following after scrapping and cleaning of the surface wherever necessary with contractor's own supply of paints & labour. The work shall be done as per extent practice on N C Railway and the instructions of Railway representative at site. Primer and paints to be used by contractor should be both of Asian Paints make. Note:-1. All steel structure material, Transportation provided by railway (Inspection By Consignee). NS 100.00 Numbers 2088.88 208888.00 AT Par 208888.00 PRAYAGRAJ DIVISION-S AND T/NORTH CENTRAL RLY Description:- Supply and provide exothermic weld in earth strip and other side with lug tightened 41 through Nut-bolt, with supply of 1 x 16 Sq mm Green multi strand copper power wire as per IS: 2465/1984 and IS:694:2010 or latest, 101 conductor each dia 0.45 +/- 0.01 with insulation thickness of 1.2 mm and nominal conductor resistance of 1.127 ohms/km and test parameters as per RDSO Specn.No.IRS:S-76/89(Amnd.3), copper Lug 16 sq mm both side, 16 sq mm cables will be laid normally on layer of soft earth under the floor. The cutting to be filled and finished with cement/concrete, and plastering. The wire will be laid in suitable PVC pipe and this work is to be executed as per directions of Railway engineer at site as per extent practice on NCR. (Inspection by Consignee ) NS 136.00 Numbers 471.22 64085.92 AT Par 64085.92

during Maintenance / Engg. Machine work and reconnection at its original place. (Inspection by Consignee) NS 143.00 Numbers 369.81 52882.83 AT Par 52882.83

Maintenance / Engg. Machine work and reconnection at its original place. (Inspection by Consignee) NS 564.00 Numbers 51.51 29051.64 AT Par 29051.64

Engg. Machine work and reconnection of insulated lead wire & double bonding wire after completion of Engg. work. (Inspection by Consignee) NS 10088.00 Numbers 92.05 928600.40 AT Par 928600.40 Description:- Cleaning, Lubrication of slide Chairs and assembly up to 3 sleepers from the toe of

powder/Lubricating oil. (Contractor to arrange required men and all other materials like kerosene oil, cotton waste, hand gloves, brush for cleaning etc. Graphite powder/Lubricating oil will be supplied by Railways) Rate is for executing the activity for 1 point one time. (Inspection by Consignee)