WBPWD/SSE/SWEC/NIQ101/2025-26

Amount

Supply & Fixing 250A capacity Kit-Kat rewireable - Porcelain fuse carrier & base (3 Nos.) on suitable size plywood, nuts, bolts etc. on wall.

Supply, Installation, Testing & Commissioning of Floor Mounted L.T. cubical type fully compartmentalized distribution panel board having rigid and self supporting structure fabricated with 14 SWG CRCA sheet with M.S. angle iron frame (main frame with 50 x 50 x 6 mm angle and each vertical compartment with 40 x 40 x 6 mm MS angle iron). The base of panel should be made with 75 mm x 40 mm x 4.4 mm M.S. channel. [Manufacturer / Fabricator having Test Certificates from CPRI]. All incoming & outgoing switches are to be housed in respective compartments hinged and gasket doors at the front. All doors should have panel locking arrangement in such a fashion that it can not be on unless the feeder remains in off position. The rear panel should gasketed wire net guard for ventilation arrangement will be made of easy accessibility to each compartment by providing rear panel doors with locking system . The panel is to be properly gasketed to prevent the dust & vermin. All vertical bus bar chambers is to properly arrange and all electrical equipments are to be fixed by nuts and bolts on suitable Hylam board / porcelain insulators of adequate size and dimension. The outgoing feeder connection from respective switches are to be made at rear side of panel by means of busbar, copper multi core cables, to be terminated on bolted type terminals for cable connection or on bush insulators for bus bar connection. Each compartment will be providing with DMC/FRP board at back side. (Make :- Lauritz Knudsen / Siemens / Schneider / ABB). (For Raw and Emergency Power Supply).

INCOMER :- a) Supply and fixing 415V, 250A TPN SFU in S.S. enclosure incl. S & F of 3 Nos. DIN type HRC fuse as per rating - 1 No. b) Supply and fixing 415V, 125A on load change over switch with operating handle kit (Make :- Lauritz Knudsen, Cat. No. - CX30001OOOO) fuse mounting kit (Make :- Lauritz Knudsen, Cat. No. - CX21250OODO) and 3 Nos. DIN type HRC fuse - 1 No.

BUSBAR :- a) S & F 415 V, 315 A current carrying capacity electrolytic grade tinned copper BBC having bus bar dimension of (4 x 40 mm x 5 mm) will be fixed on FRP Chair & the entire bars are insulated with PVC heat sinkable sleeves with suitable size & colour as per direction of E.I.C. (FOR RAW POWER BUS BAR). a) S & F 415 V, 200 A current carrying capacity electrolytic grade tinned copper BBC having bus bar dimension of (4 x 20 mm x 5 mm) will be fixed on FRP Chair & the entire bars are insulated with PVC heat sinkable sleeves with suitable size & colour as per direction of E.I.C. (FOR EMERGENCY POWER BUS BAR).

OUTGOING : a) Supply and fixing 415V, 125 A TPN SFU in S.S. enclosure incl. S & F of 3 nos. DIN type HRC fuse as per rating - 1 Set. b) Supply and fixing 415V, 100 A TPN SFU in S.S. enclosure incl. S & F of 3 nos. DIN type HRC fuse as per rating - 1 Set. c) Supply and fixing 415V, 63 A TPN SFU in S.S. enclosure incl. S & F of 3 nos. DIN type HRC fuse as per rating - 2 Set. d) Supply and fixing 415V, 32 A TPN SFU in S.S. enclosure incl. S & F of 3 nos. DIN type HRC fuse as per rating - 5 Set.

ACCESSORIES : i) Digital Multifunction Meter (class 0.5) with RTC & RS 485 port, capable of display of Current, Voltage, PF, MD with date & time stamp etc. [Make : Lauritz Knudsen / Legrand /ABB /Schneider / Siemens] ----- 1 Set. ii) CT's for metering; CL : 0.5, 250/5A, 5 VA, tape wound. (Make :- Kappa). for all three phases. ------- 2 Set. iii) 6A 10KA SP MCB ------- 3 Nos. iv) E.I. Danger Board of suitable size ------- 1 No. v) LED Indicator Lamp (RYB) - 1 Set.

INTERCONNECTION : All interconnections between incoming main to Busbar are to be made with suitable size electrolytic tinned Aluminium bars or equivalent flexible pvc insulated multistranded single core Al. cable and the same between busbar to all outgoing mains and also for metering arrangements are to be made by suitable size of Copper wire with proper socketing of the end of each wire leads.

Supply and delivery of 7 Metre Octagonal Pole, 7 Metre long octagonal poles with a shaft thickness of 3 mm, featuring the following specifications : Top Across Flats (A/F) : 70 mm Bottom Across Flats (A/F) : 130 mm Base Plate Dimensions : 200 mm x 200 mm x 12 mm Wind Load Design : Suitable for wind speeds up to 180 km/h, in accordance with IS:875 Bracket Provision: Supplied with a suitable bracket arrangement for installation of one or two LED street lights Material Specifications : A) The shaft shall be manufactured from S355JO/JR grade steel as per BS EN 10025, or E350 BR grade as per IS:2062 (or equivalent). B) The base plate shall be of E250 BR grade as per IS : 2062. C) Hot-dip galvanization shall be carried out in accordance with BS EN ISO 1461. [Make :- Bajaj / Valmont / Transrail / Lysaght] Note : The Test Certificate and Warranty Certificate from the Original Equipment Manufacturer (OEM) shall be submitted to the Engineer-in-Charge (EIC) for review and must be approved prior to execution of the work.

The pole will consist of a built-in loop-box having one 32A 4-terminal stud type connector, one 250V 2A SP MCB 'C' (Make :- Siemens / Schneider / Legrand], one NL on porcelain insulator, it permits clear access to equipment like winches, cables, socket, etc and also facilitate easy removal of the winch. The door opening shall be complete with a closefitting, vandall resistance, weatherproof door (to IP-55 of IS:2147), providing with a heavy duty double internal lock with special paddle key. The door opening shall be carefully designed and reinforced with welded steel section , so that the mast section at the base shall be unaffected and undue buckling of the cut portion is prevented. The Pole should be supplied with adequate templates for the purpose of construction of base foundation. The pole should have earthing terminals 02 (two) nos. at a height of 600 mm from the base plate for connection of earth continuity wires / conductors.

Supply and delivery of 4 Nos. M20X600 “J” Type foundation bolts as per EN - 8 Grade (TS - 600) manufactured from special steel along with nuts, washers, and templates for 7 Mtr. Pole.

Supply and delivery of 1500 mm Single Arm Bracket made of 40 NB / 48.3 OD Mild Steel Pipe as per IS:1161 suitable to insert at Pole Top A/F 70.

Construction of suitable Shallow foundation 7 Mtr. Octagonal Pole with M-20 grade concrete for Pole considering soil bearing capacity (SBC) 10T/sq. mtr. at 2 Mtr. depth with all materials and labour payment made as per PWD civil schedule & as per direction of EIC. Erection of Pole by using of lifting equipment like hydra etc. and fixing of foundation bolts, anchor plate etc. with necessary arrangement & Testing & commissioning of all electrical equipment of Pole like led fixtures, MCBs Terminal etc. with necessary connection. Testing & commissioning of all electrical equipment, Bracket fixing hardware of 7 Mtr. Octagonal Pole. All works shall be carried out in accordance with relevant IS codes, good engineering practices, and to the full satisfaction of the Engineer-in-Charge. [Note: Before execution of the foundation work for the octagonal pole, a detailed foundation drawing from the Original Equipment Manufacturer (O.E.M.) must be submitted and approved by the Engineer-in-Charge (EIC).]

S&F of 240V, 90 Watt LED Street Light including IP65 protection with CCT (5700-6500) & minimum Luminious efficacy>= 120 Lumen / Watt. with inbuilt SPD. (Make: - Philips, cat No.- BRP502 LED126CW R3C PSU S1/ Wipro / Bajaj). (with 5 years warranty).

Inter connection of LED fittings by 3 x 1.5 Sq.mm. PVC insulated copper wire from loop box with 19 mm bore PVC polythene pipes as per direction of EIC.

Supply & Delivery of 1.1 KV Gr. XLPE insulated as per IS -7098 (Part -1) 1988 armoured sheathed Aluminium conductor cable. (Make :- Havells / Polycab / RR Kabel). 4 core 10 Sq.mm.

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.

Laying of cable as below, after cutting floor / pavement / wall and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish.

From 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor / pavement / wall etc.

Laying of cable upto 3/4 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting.

Laying only Cable upto 50 sqmm through existing RCC / Hume / GI Pipe / open masonary trench for single, 2, 3, 3½ & 4 core.

Supplying & fixing medium gauge GI Pipe (ISI-Medium) Protection with necessary fittings and jointing metarials as required. 32 mm dia.

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE / PVC armoured cables as below : 4 core 10 Sq.mm.

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials : 4 Core 10 Sq.mm.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI - Medium GI pipe.

Excavation of soil for installation of Earth Electrode and filling & ramming. For Morrum Soil.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work (1 : 6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 36.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe.

Connecting the equipments body to earth busbar including S & F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required. 2x84/0.3 (4 sqmm) + 1x56/0.3 (2.5 sqmm) as ECC.

Finishing of the PVC insulated wire ends by socketting with pin / ring type copper sockets and insulated tapes etc., including supplying sockets, tapes.

S & F of Glow Sign Board (12 ft x 4 ft x 6 inch. depth) made from 40 x 40 x 5 mm MS angle, 40 x 5 mm MS flat having the provision for opening from front by 25 x 25 x 5 mm MS angle, 3 nos. hinges duly welded. The board should be enclosed from out side by 20 SWG GI SHEET except the front. The entire board should be painted with one coat of synthetic enamel paint over one coat of RO primer. The front facia of the board is to be made with 2 mm thick approved colour PVC sheet of export quality having suitable size and to be fixed on the front structure by S & F suitable size aluminium angle, SS Screws. The matter is to be encrypted on a whole best quality venyle sheet as per approved size, colour & matter which will be pasted properly over the PVC sheet. S & F of 25 (twenty five) Nos. 4 feet single LED fitting including incl. all accessories (Make :- Philips, Cat. No.- TMC 502 1xT-LED 22W / Wipro of equivalent or higher specifications) including S & F of 230V, 18 watt Polycarbonate body, Aluminium heat sink, 2100 lm LED Mas tube light (Make :- Philips, Cat. No. - Mas LEDTube 1200 mm 18W 865 T8I - 2100 lm / Wipro of equivalent or higher specifications) and making entire connection with 3 x 1.5 sq.mm. stranded copper wire (Make :- Havells / RR Kabel / Finolex) through flexible PVC pipe for proper illumination of the GSB from inside as per direction of EIC. --- 2 nos.

Supplying & Fixing GI waterproof type looping cable box size 200 x 150 x 100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint.

S & F 415V 32A Timer controller for compound lights in SS double door (2+10) way DB enclosure (Make :- L&T, enclosure Cat. No. - DBSPN012DD or equivalent) with S & F following electrical accessories & front door locking arrangement with all connection by finishing the ends of 2 x 4 & 1 x 2.5 copper wire dowells solderless socket by crimping method as to GS earthing attachment on wall incl. necessary connections as per direction of EIC:- i) 32A TPMCB. (Make :- L&T) --- 1 No. ii) 24 Hr. programmable Digital/Analog Timer. (Make :- L&T, Cat. No. - 67DDT0) --- 1 No. iii) 3 pole 32A power contactor. (Make :- L&T,Type MNX) with 1 NO + NC additional contact block --- 1 No. v) 2 Module plate with cover (Make :- Legrand - Myrius Regular) -- 1 No vi) On, Off push button -- 2 Nos. (Make :- L&T/ ABB) --- 1 No. vii) 2A Auto - Off - Bypass SPDT toggle switch. (Make :- Approved / Reputed) --- 1 No. viii) Outgoing connector. (Make :- Approved / Reputed) --- 1 No.

Supply & Delivery of 1.1 KV Gr. XLPE insulated as per IS -7098 (Part -1) 1988 armoured sheathed Aluminium conductor cable. (Make :- Havells / Polycab / RR Kabel). 4 core 35 Sq.mm.

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.

Laying of cable as below, after cutting floor / pavement / wall and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish. From 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor / pavement / wall etc.

Supplying & fixing medium gauge GI Pipe (ISI-Medium) Protection with necessary fittings and jointing metarials as required. 50 mm dia

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE / PVC armoured cables as below : 4 core 35 Sq.mm.

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials : 4 core 35 Sq.mm.

Earthing with Copper plate (610 x 610 x 3 mm size) having weight of 9.84 Kg and 1 No. 25 x 5 mm Copper strip (3.20 mt long) & 1 No. 6 sqmm PVC insulated stranded Copper wire (4 Mt long) incl. S & F 15 mm dia GI pipe (ISI-Medium) protection (4 mt. long) to be fillied with bitumen, partly under the ground level & partly above ground level to an average depth of 3.65 Mts. below the ground level and restoring the surface duly rammed incl. providing 3.0 mt long, 25 mm dia GI pipe (ISI-Medium) for periodic treatment, incl. providing masonery enclosure on the top of the earth electrode of overall size 86.36x86.36x46cm deep (below Ground level) complete with cemented brick work (1:6) of 25 cm width, duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 x 36.56 cm with locking arrangement, GI reducer and treatment of soil by using salt & charcoal or coke for plate electrode. (For Neutral Earthing).

Supplying & fixing earth busbar of copper bar flat 50 mm x 5 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required as per GS .

Connecting the equipments to earth busbar including S & F copper strip of size 25 mm x 6 mm in UG trench with necy arrangement.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI - Medium GI pipe. (For Equipment Earthing).

Excavation of soil for installation of Earth Electrode and filling & ramming. For Morrum Soil.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall / floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work (1 : 6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe.

Construction of DG Set Foundation size by 10 Ft. (L) x 6 Ft. (W) (3 Ft. below the ground level and 2.5 Ft. above the ground level), ordinary cement concrete mix. 1 : 1.5 : 3 with graded stone chips of 20 mm down pakur variety laying concrete base (1 : 3 : 6) using 40 mm down stone metal & single brick flat solling of picked jhama brick incl. at shuttering work by 25 mm to 30 mm thick wooden plank also, reinforcement with 8 mm tor steel atleast 150 Kg total, this rate are incl. all materials , labour charges & carrying etc. (As per direction of EIC).

M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS : 816-1969 & IS : 9595 using electrodes of approved make and brand conforming to IS:814 - 2004, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour required for execution and all incidental chages (such as electricity, labour insurance) etc. complete. Payment to be made on the basis of calculated weight of structural members of MS Hollow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a height of erection 8 m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4 m. beyond the initial 8 m. or part thereof. i) For roof truss works. a) Span up to 12 Mtr.

Drilling holes of requisite diameter in R.S. joists channels, tees. Plates etc. (b) (I) Dia.above 12 mm and depth upto 10 mm.

Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed. (i) 16 mm dia bolt. (b) 450 mm long.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with superior quality aluminium paint of approved make and brand including smoothening surface by sand papering etc. on steel surface : (b) Two coats

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). (i) In Roof :- (a) With 0.5 mm thick sheet.

Supplying and fixing of 415V TPN with fuse on L&N Sheet steel Main Switches on flat iron frame on wall. (Make :- Standard / Havells / HPL). 32 A.

Supply & Fixing of 3 Phase 3 HP D.O.L. Starter fixing on angle iron frame on wall. (Make :- Lauritz Knudsen, Cat. No. - SS97756COTO).

Supply & Delivery of 1.1 KV Gr. XLPE insulated as per IS - 7098 (Part -1) 1988 armoured sheathed Aluminium conductor cable. (Make :- Havells / Polycab / RR Kabel). 4 core 10 Sq.mm.

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.

Laying of cable as below, after cutting floor / pavement / wall and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish. From 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor / pavement / wall etc.

Laying of cable upto 3/4 core 25 sqmm on wall / surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting.

Laying only Cable upto 50 sqmm through existing RCC / Hume / GI Pipe / open masonary trench for single, 2, 3, 3½ & 4 core.

Supplying & fixing medium gauge GI Pipe (ISI-Medium) Protection with necessary fittings and jointing metarials as required. 32 mm dia.

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE / PVC armoured cables as below : 4 core 10 Sq.mm.

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials : 4 Core 10 Sq.mm.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI - Medium GI pipe.

Excavation of soil for installation of Earth Electrode and filling & ramming. For Morrum Soil.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work (1 : 6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 36.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe.

Supply & Delivery of Split type fixed speed, Non-Inverter Air-conditioning machine having the following specification : Rated ISEER : 3.81, Compressor Type : Hyper Tropical Rotary, Rated Voltage / Phase / Frequency : 230V / Single / 50 Hz, Power Consumption at 100% Capacity (Watts) : 1850, Standard Cooling at 100% Capacity (Watts) : 7050, Airflow rate for indoor unit (m3 / h) : 1480, PM filter, Eco Cool 4 way wide & long airflow, LCD remote control, Electronic metal housing box, 12 hour on and off timer, auto restart, auto swing, fan speed option (low / medium / high / turbo) etc. Refrigerant- R32. Min. BEE Star Rating : 3 star, Minimum Tonnage : 2.0 Ton or Higher. [Make :- General, Model No. - ASGA24BUTA-B / Equivalent or Higher specifications of Mitsubishi Electric].

Supply & Delivery of Split type fixed speed, Non-Inverter Air-conditioning machine having the following specification : Rated ISEER : 3.90, Compressor Type : Hyper Tropical Rotary, Rated Voltage / Phase / Frequency : 230V / Single / 50 Hz, Power Consumption at 100% Capacity (Watts) : 1360, Standard Cooling at 100% Capacity (Watts) : 5300, Airflow rate for indoor unit (m3 / h) : 1480, PM filter, Eco Cool 4 way wide & long airflow, LCD remote control, Electronic metal housing box, 12 hour on and off timer, auto restart, auto swing, fan speed option (low / medium / high / turbo) etc. Refrigerant- R32. Min. BEE Star Rating : 3 star, Minimum Tonnage : 1.5 Ton or Higher. [Make :- General, Model No. - ASGA18BUTA-B / Equivalent or Higher specifications of Mitsubishi Electric].

Installation,Commissioning and Testing of 1.9 ton Or Higher Split type AC machine both indoor / outdoor including fixing of 40 x 40 x 5 mm MS angle iron frame and mending good the damages.

Supply and laying of 3 core 2.5 sqmm 1.1 KV grade XLPE insulated round flexible copper cable. (Make:- Havells / RR Kabel / Polycab / Finolex).

Supply and delivery of (I) Copper pipe 3/8" / 1/2" for liquid as required. (II) Copper pipe 5/8" / 1/4" for suction as required.

Supply and drawing of 10 mm thick nitrile rubber insulation & Aluminium strip taping for 3/8" / 1/2" for liquid & 5/8" / 1/4" for suction as required.

Cost of charge - 20 mm dia. PVC drain pipe.

Rigid 32 mm PVC water pipe with 10 mm nitrile rubber insulation & Aluminium strip taping including tee, bend, plug, socket etc. as required.

ELCON ENGINEERS (BID ID -7804594)

BAPPA CONSTRUCTION (BID ID -7814459)