Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹52.3 LAccepted-AOC | L1 | Accepted-AOC The lowest tenderer | |
| 2 | L2₹55.4 L+₹23,243 (0.42%)Rejected-Finance | L2 | Rejected-Finance Not the lowest tenderer | |
| 3 | L3₹56.4 L+₹1.2 L (2.20%)Rejected-Finance | L3 | Rejected-Finance Not the lowest tenderer | |
| 4 | L4₹57.4 L+₹2.2 L (4.01%)Rejected-Finance | L4 | Rejected-Finance Not the lowest tenderer | |
| 5 | L5₹58.6 L+₹3.4 L (6.14%)Rejected-Finance | L5 | Rejected-Finance Not the lowest tenderer |
Tender Value
Refer Docs
EMD Value
₹1.2 L
Closing Date
8 May 2024, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
HQ CWE SRI GANGANAGAR
HQ CWE POST BOX 48 SRI GANGANAGAR-335001 (Rajasthan)
SPL REPAIRS TO BLDG NO P14 AT MIL STN ABOHAR
2024_MES_649805_1
CA NO CWE SGNR T-90 OF 2023-24
Open Tender
Civil Works
Item Rate
180 days
GE ABOHAR
As per NIT
9 documents required · 9 mandatory
₹1,000
GE ABOHAR
₹1.2 L
15 Jun 2024
10 Apr 2024
9 May 2024
10 Apr 2024
8 May 2024
24 Apr 2024
Amount
Demolition of cement concrete (un-reinforced) in floors / pavings, (below or above ground level) and of any description and in any position complete all as specified and directed.
Demolition of cement concrete (reinforced) in roof , floors (other than ground floor), beams, staircase, landing, chajjas and similar suspepnded work
Demolition of mud in roofs any thickness including plastering and leeping complete all as specified and directed by Engineer-in-Charge.
Dismantling of brick tiles or terracing tiles in roofs single layer complete all as specified and directed by Engineer-in-Charge.
M & L for 75 mm thick cement concrete type C2, 1:3:6, (40mm graded stone aggregate) as in plinth protection/ path etc laid in suitable panels not exceeding 3.00 m length finished even and smooth without using extra cement with 10mm joints filled with bituminous sealing compound of grade 'A' / bitumen mastic filler /sealant , surface finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.
M&L for cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4, Type B-0, as required (superficial area n. exc 150 sq cm) all as specified
M & L mild steel TMT bars 10mm dia or over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as in column, beam etc complete all as specified and directed.
All as per Ser item No 7.00 above but 5 mm dia and over up to and including 8 mm dia as in stirrups.
M&L for reinforced cement concrete M-25 Design mix, type using 20mm graded stone aggregate as in as in foundations, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete complee all as specified and directed by Engineer-in-Charge.
M&L for reinforced cement concrete M-25 Design mix, type using 20mm graded stone aggregate as in Columns, pillars, piers, posts & struts etc. all as specified and directed. Note : Form work & reinforcement measured and paid under respective item of BOQ.
M&L for reinforced cement concrete M-25 Design mix, type using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5 metre span all as specified and directed. Note : Form work & reinforcement measured and paid under respective item of BOQ.
M&L for reinforced cement concrete M-25 Design mix, type using 20mm graded stone aggregate in slab supported on walls,beams and columns in floors, roofs, landings, balconiies, deck slabs and in shelves and the like all as specified and directed. Note : Form work & reinforcement measured and paid under respective item of BOQ.
M&L for Form work to sides of concrete foundation, footings bases of columns and plinth beams and similar works rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.
M&L for Formwork to soffits of suspended slabs, such as roof slabs, floor slabs landing and similar work not exceeding 200mm thick (Horizontal & sloping) fair finished surfaces Note- Steel props shall be used in formwork.
M&L for Fromwork to edges of concrete flates treads breaks in floors, window cill concrete railing, opening in convert valley floor and roof exc 5 but n.exc 10 cm wide and sides RCC/PCC band in walls complete all as specified and directed by Engineer-in-Charge.
M&L for Formwork to sides of pillars, posts, struts, piers columns & stanchions : rough finished surface of concrete flat complete all as specified and directed by Engineer-in-Charge.
M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.
S & F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified.
Dismantling of brick work built in any cement mortar all as specified.
M&L for Brick work using fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.
All as per Ser item No 20.00 above but except bricks all as specified .
M & L for brick work in half brick thick wall using fly ash bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.
Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the permices complete all as specified and directed by Engineer-in-Charge.
Roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust etc.
M & L for glazed ceramic coloured tiles 7mm thick 300 x 450mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick cement sand screed bed (1:3) complete all as specified.
M & L for non skid ceramic coloured joint free tiles with matt finish, 7 to 8 mm thick ( square/ rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in paste pigmented to tile shade over and including 15mm thick cement and sand screed (1:4) complete all as specified and directed by Engineer - in - Charge.
All as per Ser item No 26.00 above but as in skirting over 10 mm cement mortar backing coat (1:3) complete all as specified and directed by Engineer-in-Charge.
M & L Machine cut kota stone slab flooring 20 - 25 mm thick over and including cement screed base laid over and including 15mm thick screed bed in cement mortar 1:6 set and jointed with grey cement slurry mixed with pigment to match of the slab including rubbing and polishing complete all as directed.
M & L Machine cut kota stone slab 20 - 25 mm thick in riser of steps,skirting,dado and pillar over cement screed base laid over and including 10mm thick screed bed in cement mortar 1:4 set and jointed with grey cement slurry mixed with pigment to match of the slab including rubbing and polishing complete all as directed.
M&L for Granite 20mm thick (of any type) works (table rubbed and polished) in step, window cills, cooking platforms over and including 20mm thick cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigments to match complete all as specified and directed by Engineer-in-Charge.
Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each all as specified .
Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each and all as specified.
Taking down shutters and refixing in same opening but area exceeding 1.00 Sqm and not exceeding 2.0 Sqm all as specified.
Taking down shutters but area exceeding 1.00 Sqm and not exceeding 2.0 Sqm all as specified.
S&F "fiberways" brand fiber glass reinforced plastic (FRP) Door frame of three legged of cross section 90x45 mm size single rebate of 32mmx15mm to receive shutter of 30mm thickness. The laminate door frame moulded with two resistant grade unsatratedpolyster plain and chapped mat or frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all two three legs. The frame shall be covered with fibre glass from all side. MS stay shall be provided at the bottem to steady the frame.
S&F "fiberways" brand 30mm thick glass fiber reinforced plastic (FRP) panelled door shutter of required colour are approver brand and manufacture made with fire resistance grade unsatratedpolyster plain moulded to 3mm thick fiber laminate for foming hollow ralliuded styles with wooden frame and suitable blocks of sessoned wood inside at required place for fixing of fiber-cast monolithitically with 5mm thick FRB laminated for panels and conforming to IS-4858-2000.
S & F Aluminium butt hinges, medium weight 100 mm size fixed with steel screw all as specified.
S & F tower bolt 150 mm of aluminium all as specified.
S & F door handle D type 150 mm of aluminium all as specified.
S & F Factory made 35mm thick IInd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified.
S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as specified.
S & F Factory made Plain framed, panelled shutter IInd class hardwood rail and style 35 mm thickness (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated
S & F pressed steel door frames with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified size of frame 105X60mm all as specified .
S & F pressed steel door frames size of 125X60mm with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified
M&L Cement concrete 1:3:6, type C-1 using 20mm graded stone aggregate, for filling of pressed steel frame and hold fast blocks etc all as specified .
S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long all as specified .
S & F aluminium bow handle 150 mm long all as specified.
S & F mild steel sliding door, bolts, plate type, stove enamelled black with bright bolt not less than 12mm bore, length of bolt 250mm all as specified.
S & F mild steel 300mm ordinary rat rail rod pattern spring inluding roller and roller plate complete all as specified.
S & F small fittings such as door stops and like, including all necessary labours articles not exceeding 200 Cucm each of 2nd class hard wood all as specified .
S&F hasp & staple safety type mild steel with hinges pins incl bolt to hinge plate fixed with screw 125mm complete all as specified and directed by Engineer-in-Charge.
S&F peg set of stainless steel solid body of 125mm to 175 mm having 6 Nos hooks fixed with brass chromium plated screws complete all as specified.
S& F in repairs curtain rod of aluminium alloy of 25 mm dia with fixing brackets, stops, rollers etc complete all as specified.
S&F powder coated aluminium sliding window with and including three track with two glass shutters using 4 mm thick glass tinted and one shutter with stainless steel wire gauge wire cloth 0.36 mm nominal dia of wire and width of aperture 1.40 mm using aluminium powder coated section aluminium cleat, PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under :- (i) Three track top and vertical –jindal main-2010 section No 20621 or equivalent as approved by GE. (ii) Three track bottom-Jindal main-2010 section No 20620 or equivalent as approved by GE. (iii) Shutter vertical section-Jindal main-2010 section 20604 or equivalent as approved by GE. (iv) Shutter top and bottom –Jindal main – 2010 section 20604 or equivalent as approved by GE. (v) Shutter vertical middle (interlock) – Jindal main – 2010 section 20605 or equivalent as approved by GE. Note :- (i) Cost of Glass, wire cloth, three shutter and three track frame alongwith fixtures (push lock) etc shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. (ii) Measurement for payment shall be the opening area of the window between inner edges of wall.
S&F for powder quoted Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.
Supply & fixing anodised aluminium window shutter (glazed or gauzed), side and top hung type without sash bars, made out of aluminium section weighing not less than 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings (each shutter) such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos) suitable handle (1 No.), complete all as specified and as directed by Engineer-in-Charge. Note :- Aluminium chowkhat/ frame, Glass, wiremesh and grill where required shall be measured and paid separately under appropriate item of BOQ.
S&F aluminum powder coated grill weight not less than 1.50 Kg /sqm in window ,doors or ventilators including fixing material complete all as specified and directed by Engineer-in-Charge.
M & L Washed stone grit plaster on exterior walls in two layers under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per sqm, top layer 15 mm cement plaster 1:1/2:2 (1 cement : ½ coarse sand : 2 stone chipping 10 mm normal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to be expose the stone chippings complete all as specified. Note : Payment for providing grooves shall be made separately.
Forming groove of uniform size 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden batterns, nailed to the under layer including removal of wooden battens, repair to the edges of panels, filling of epoxcy and finishing the groove complete as per specification and direction of the Engineer-in-Charge
S & F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified.
S & F figured glass 4 mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan complete all as specified.
Material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick PVC sheet (prelam) having one side decorative laminated sheet (for shutter, back side of cabinet, sides of cabinet, partition and shelves etc). All the edges of shutter and front exposed edge of partition/shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. Including all required fixing material such as SS brackets, screws, adhesive etc., including taking out old any type cabinet complete all as specified and as directed by Engineer-in-charge. Note :- (i) The area of each sheet (shutter, back side of cabinet, sides of cabinet, partition and shelves) shall be measured in sqm for payment. (ii) Magnetic catcher, handles, continuous Piano hinges and PVC frame (where required) shall be measured and paid separately under appropriate item of BOQ. (iii) Any other material required for making/fixing/hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.
S&F magnetic catcher fixed with nut screw and washer complete all as specified and directed by Engr-in-charge.
S&F extruded brass handle fabricated type 100mm long cabinet fixed with steel screw complete all as specified and directed by Engineer -in - Charge.
S&F Continuous (piano) hinges, stainless steel, bright finish, width of flap when open 30mm complete all as specified and directed by Engineer -in - Charge.
Supply and fixing Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as directed by Engineer-in-Charge. Note :- Frame shall be elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.
M & L providing two coats of synthetic enamel paint over new surface and a coat of red oxide primer on steel surfaces including preparation of surface of any description not exceeding 10 cm width or girth all as specified.
Dismantling wrought iron or mild steel work of any description all as specified.
S & F structural steel work rolled mild steel joist, channel,angle, or Tee sections, fixed independently conforming to Fe 410-W all as specified.
S & F exc 12 mm dia & n. exc 20 mm dia of neck mild steel bolts purpose made with hexogonal or square head one and end and screwed to other, or screwed to both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 30 cm long.
M&L plates (plain or chequered) channels , square cut or notched (ordinary and counter sunk) forming holes , without any attachment Fe-410 -W (Gde -e -250) quality -B complete all as specified and directed.
S & F framed work such as grills, cooler stand ,grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290.Gde -E- 165 all as specified.
S&F in repair sink with drainage board made of Stainless Steel 1mm thick kitchen with plug washer and waste including bedding in cement mortar to dwarf wall including fixing contilever brackets/on shelve, connecting union to pipe over all size 915x460 mm bowl of size 410 x 330 x 160 mm .
Dismantaling boarding, any discription fixed in any position with nails.
Material and labour for water proofing treatment to sunken slab and adjoining vertical surfaces as per any one of the two method as specified in PSS-II respective clause of CA complete all as directed by Engineer-in-charge/GE. Note : (i) Work shall be executed through specialized agency (ii) The treatment shall be carried out as per the manufactures instructions and as directed by the Engineer in charge. The name of firm shall be got approved from CWE before carrying out the work. (iii) Treatment should be continue on sunken floor and on vertical walls of sunken portion. (iv) PCC filling under sunken area will be measured & paid separately.
M&L for providing 100mm cement concrete Type E-2, 1:5:10 (40 mm graded stone aggregate) as in foundation, filling and mass concrete.
S&F Stainless steel plate rack of size 750mm x 600mm, made out of 1mm thick stainless steel of sheet of 1st quality complete all as specified and directed by Engineer -in -charge.
S & F in repair vitreous china squatting pan Orrisa pattern size 580mm x 440mm white with integral foot rest with PVC ‘P’ or ‘S’ trap and fixing in cement concrete, 150mm thick all round and finished just below level of rim of pan to receive the floor finishing all as specified.
S & F in repairs PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified.
S & F vitrous china oval corner wash hand basin white of small size 450X390 mm including brackets 300mm long PVC connection with brass nuts, 40mm dia waste coupling including cutting for and pinning in end of brackets or erecting stand etc coloured top bowl type screwed shank fly nut flange end including cutting for and pinning in granite slab of hole including 32 mm dia chromium plated waste coupling and bottle trap all as specified.
S&F in repair 15mm bore bib taps,chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, secrewed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in- charge.
S & F in repairs 15mm bore stop cock chromium plated fancy type , high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified .
S&F brass chromium plated central hole basin mixer with regular spout,popup waste system and including 450mm long braided hoses Hot and cold with connection and nuts complete all as specified and directed by Engr-in-charge.
S & F in repairs 15mm bore stop valve, cast copper alloy fancy type chromium plated with long shank and cup ( concealed type ) screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed .
S&F Sink mixer with swinging spout(wall mounted model)Chromium plated brass with connection and nut complete all as specified and directed by Engr-in-charge.
S&F brass chromium plated wall mixer for mixing hot& cold water screwed down for iron pipe and fixed as directed by Engr-in- charge.
S & F in repair PVC connection 15mm size with nuts of length 450mm suitable hot and cold all as specified.
S&F PVC bathroom cabinet mirror 450 x 350 mm complete all as specified and directed by Engr-in-charge.
S&F in repair 125mm size Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipeor union complete all as specified and directed by Engineer-in-Charge.
Material and labour for complete removal of existing treatment on Old external wall surfaces of any description, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and directed by Engineer-in- charge and applying the following:- (a) Applying Wall care putty in two coats for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers by Mechanical method (hand electric grinder) prepatory to paint as directed. (b) Two coats of exterior acrylic paint of approved tint over a coat of cement primer on old prepared surface by using paint brush / Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible.
S & F in repair soap dish vitreous china white approximately size 160 x160x 90 mm and fixed with as chromium plated brass screws complete all as specified and directed by Engineer -in -charge.
S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.
S&F for PVC corner shelf set of 3 with bracket complete all as specified and directed by Engr-in- charge.
Taking down steel tubing 15mm bore and connections complete all as specified.
Fixing only tubes any grade 15mm bore to walls and ceiling or in floors etc including provision of new fittings as required (Serviceable galvanised tubes retrieved from respective items shall be laid under these items) all as specified.
S & F 15mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor all as specified.
Taking down steel tubing 20mm bore and connections complete all as specified.
Fixing only tubes any grade 20mm bore to walls and ceiling or in floors etc including provision of new fittings as required (Serviceable galvanised tubes retrieved from respective items shall be laid under these items) all as specified.
S & F 20mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor all as specified.
Dismantling water tanks of 500 ltrs complete all as specified and directed by Engineer-in-Charge.
S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres all as specified and directed by Engineer - in - Charge.
M&L Ball brass valves 20mm, high pressure, with polythene float and fly nut complete, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.
S & F in repair 15mm bore gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed all as specified .
S & F in repair 20mm bore gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed all as specified.
Taking down CI/AC/PVC soil waste and vent pipe any radius including all fittings complete.
S & F PVC socketed SWR pipe with rubber ring joints 110mm dia fixed to wall complete all as specified.
S & F PVC socketed SWR pipe and pressure rating not less then 6kg/f /sqcm with rubber ring joints 75mm dia fixed to wall complete all as specified .
S&F cast iron waste and vent pipe and pressure rating not less then 6kg/f /sqcm in any length with or without ear with cement joints laid in trenches or in floor 100mm dia.
All as per Ser item No 109.00 above but 75mm bore complete all as specified and directed by Engineer-in-Charge.
S&F for 110mm bore PVC (SWR) bends any radious provided with access door complete all as specified and directed by Engineer-in-Charge.
S&F for 75mm bore PVC (SWR) bends any radious provided with access door complete all as specified and directed by Engineer-in-Charge.
S&F for 75 mm bore PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.
S & F Grating doom 125 mm dia with waste hole of PTMT ( Min wt 40 gm )
Taking down cement plaster/dado on brick wall including racking out joints, hacking for keys scrubbing down with water all as specified.
M & L rendering 15mm thick on fair faces or other than fair faces of brick work in CM 1:6 finished even & smooth without using extra cement all as specified.
M & L rendering 15mm thick on fair faces of brick work in CM 1:4 finished even & smooth without using extra cement all as specified.
Providing & applying Rising damp proof coating system with single component ready to use damp-proof coating water proofing compound: (a) SURFACE PREPARATION: Thoroughly brush and clean all laitance,loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings etc. all large voids or hollow portions must be removed and replastered.Non-moving cracks having width upto 5 mm must be filled with polymer based crack filler. (b) APPLICATION : Apply the first coat of Hydamp with paintbrush directly on the prepared surfaces. Allow to dry for a minimum 2-3 hrs.Apply one part of water proofing compound and 2 parts of OPC white cement and make the putty, apply putty on the entire surface area. Allow it to dry for atleast 3-4 hours. Apply the final coat of water proofing compound on the entire surface.
M&L for preparation of surfaces and applying three coats of white wash on ceiling complete all as specified and directed by Engineer-in-Charge.
M&L for preparation of surface and applying two coats of white wash on wall complete all as specified and directed by Engineer-in-Charge.
Material and labour for Preparation of new plastered Internal wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty in two coats on wall surface and smoothening the surfcae with sand papers by Mechanical method (hand electric grinder) prepatory to paint as directed. (b) Two coats of interior acrylic paint of approved tint over a coat of cement primer by using paint brush / Roller.
Material and labour for complete removal of existing treatment on Old internal wall surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and as directed by Engineer-in- charge and applying the following:- (a) Applying Wall care putty in two coats for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers by Mechanical method (hand electric grinder) prepatory to paint as directed. (b) Two coats of interior acrylic paint of approved tint over a one coat of cement primer on old prepared surface by using paint brush / Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible.
M&L for preparation of two coats of cement base paint over a coat of alkali resistant prilmer on newly plastered surface of wall complete all as specified and directed by Engr-in-charge.
M&L for complete removal of old plastered wall surfaces and applying two coat of cement base paint over a coat of alkali resistant primer complete all as specified and directed by Engr-in-charge.
M&L for preperation of old wooden surface and applying one coat of synthetic enamel paint complete all as specified.
M&L for preperation of old steel surface and applying one coat of synthetic enamel paint complete all as specified.
M & L providing two coats of synthetic enamel paint over a coat of pink primer on new wooden surface including preparation of surface with primer all as specified.
M & L providing two coats of synthetic enamel paint over new surface and a coat of red oxide primer on steel surfaces including preparation of surface of any description not exceeding 10 cm width or girth all as specified.
Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.
M&L for hard core of broken bricks of gauge not exceeding 63mm, deposited,spread and leveled in layers not exceeding 15cm thick, watered and rammed to a true surface.
M&L for 75 mm thick PCC 1:4:8, type D-2, (using 40mm graded stone aggregate) as in sub base complete all as specified and directed by Engineer-in-Charge.
M&L for Machine pressed precast concrete coloured interlocking paver block any shape and size conforming to IS 15658-2006 of 80 mm thickness M-40 Grade over and including 25 mm thick layer of fine sand complete all as specified and directed by Engineer-in-Charge.
M&L for contineous brick edging with burnt clay brick work with sub class ‘B’ with width equal to width of brick laid dry on end vertically complete all as specified and directed by Engineer-in-Charge.
S&F Floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engineer-in-Charge.
Excavation trenches n exc 1.50 wide and n exc 1.50 m depth for foundation etc in any type of soil complete all as specified and directed by Engineer-in-Charge.
Returning filling in including spreading leveling, watering and well ramming in layers n exc 25 mm thick soil complete all as specified and directed by Engineer-in-Charge.
Removing excavated material n exc 250 m and deposited where directed at a level not exc 1.50 m above the starting point complete all as specified and directed by Engineer-in-Charge.
M&L Providing cement concrete Type D-2, 1:4:8 (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.
S&F cast iron bend ( any radius) dimenshing pieces or tappers ( large bore measured) 100mm bore.
All as per Ser item No 139.00 above but 75 mm bore.
S&F in repair cast iron floor trap 75mm dia incl jointing to waste pipe fixed in cement concrete type B-1, 1:2:4, complete all as specified and directed by Engineer-in-Charge.
S & F steel work in rectanguler/square trusses incl special shaped washer etc complete using ERW or incl butt welded tubes confirming to relevant IS code with preparation of surface and applying one coat of zink chrome primer complete all as specified and directed by Engineer-in-Charge.
S&F 50mm thick PUF panel made of Puf insulation in core having density (40+2) Kg/Cum sandwiched betweeen two numbers of polyster coated galvalume steel sheet. These sheets shall be made out of 0.50mm thick (TCT) High tensile steel having min yield strength of 550 Mpa confirm to AZ 150 of AS-1397 wityh hot dip metalic coating of 55% ZN alloy having total coating mass of minimum 150 gms/sqm inclusive of bothside. the material shall be coated with polyster coating paint system of 20 micron over primer of 5 micron (exposed side) & alkyd back coat of 5 micron over primer coat of 5 microns.the material shall be supplied as per drawing (approved by GE),colour and as per instruction complete all as specified and directed by Engineer-in-charge.
S&F Anodised aluminium snap grid frame work for false ceiling Size of Grid 605 x605 mm with 6mm dia GI wire hanger ( upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long Complete all as specified and directed by Engr-in -Charge.
S&F,7 to 8 mm thick exposed metal frame celing with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mmx600mm grid all as per manufacturer's instructions. finish, fixed to aluminium/ CGI frame work with hold down clips in false ceiling complete all as specified.
M& L for Pre painted gavalume zinc coating GI based plain steel sheet 0.50mm thick for ridge ,hip,vally gutter ,drips of an colour having tensile strength of 550 Mpa as in wall,fixed with self tapping screws complete all as specified.
M& L for Pre painted gavalume zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof coverings/cladding to wall,fixed with self tapping screws complete all as specified.
Shotcreting 25mm thick in RCC columns, beams and slabs etc in layers with approved design mix (minimum cement content of 350 Kg/Cum on M-25) concrete having the specified minimum characterristic compressive strength (with ordinary protland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria) including the cost of centring and shuttering at edges and corners etc as directed by Engineer-in-Charge including Chipping of unsound /weak concrete material 25 mm average thickness from slabs, beams, columns etc with manual chisel and /or by standred power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and thoroughly washing with water and allowing it to dry etc. including removal of rust by applying approved rust removal chemical & the coating with Dr Fixit epoxy zinc primer@ 6sqm/ltr at DFT of 100microns as per specifications and disposal of debries for all lead and lifts all complete as per direction of Engineer-in-Charge.
S&F Hard drawn steel wire fabric not exc 4Kg/Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt all as specified & directed by Engineer-in-Charge.
M & L 5mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge .
M& L PCC 1:2:4, type B1, using 20 mm graded stone aggregate, as in bed blocks , coping, hold fast blocks etc complete all as specified and directed by Engineer-in-Charge.
Removing excavated material n exc 50m and depositing where as directed at a level n exc. 1.5 m above the starting point comlete all as specified.
M & L for sand cushioning with dry and clean locally available sand for underground cable 8cm before laying cable and 15 cm after laying cable and punned to 18 cm after laying of cable complete all as specified and directed by Engineer-in-Charge Note: Pressed thickness shall be considered for payment purpose
M & L brick sub class 'B' locally available best quality laid in trenches above sand consolidted forcable protection complete all as specified and directed.
Supplying, laying, jointing and testing in repplacement XLPE PVC insulated heavy duty multi stranded armoured and PVC sheathed LT cable 1100 volts grade with aluminium conductor cross sectional area 25 sqmm 4 core conforming to IS- 1554 laid in trenches/ ducts/ along poles/ through pipes complete all as specified & directed by Engineer-in- charge. Note: Excavation & earth work shall be measured & paid separately under appropriate item of this Schedule.
Taking down carefully copper /aluminium point wiring (light, fan, socket or power) complete incl fixture and fitting such as Switches, ceiling roses, pandents, regulators,sockets, light fitting etc removing materials to store for keeping in safe custody for taking credit(credit for above items shuold be made as per conditions separately) and making good distrubed surface of wall ,floors etc. complete all as specified and as directed.
M & L point wiring with PVC FRLS insulated unsheathed multistranded copper conductor drawn in and incl of size 1.5 Sqmm, 1100V grade in concealed PVC regid conduit of suitable size, including provn of of 1.2 mm thich pressed steel sunken terminal boxes 60mm deep,suitable lenthand painted with red oxide primer for mounting switches, sockets, fan regulators covered with and including 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including 1.5 Sqmm PVC insulated stranded copper conductor as earth continuity wire and connected to common earth dolly with copper lugs inserted in including MS boards complete heavy duty for housing switches, sockets, regulators, bell push etc, complete all as directed for the following:-
One light/Bell/fan point controlled by one way switch 5 Amp.
One light/Bell/fan point controlled by one two way switch 5 Amp.
One 3 pin socket outlet, 5 Amps on the same board complete all as specified and directed.
One 3 pin socket outlet, 5 Amps on independent board complete all as specified and directed.
All as per Ser item No 157.00 above but with cable of 2.5 sq mm for 15 amps Socket Independent board with other switches complete all as specified.
All as per Ser item No 157.00 above but for 15 amps socket outlet with 4 Sqmm Copper incl 4.0 Sqmm PVC insulated copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and directed.
M & L point wiring with PVC FRLS insulated unsheathed multistranded copper conductor of size 1.5 Sqmm, 1100V grade in Existing concealed conduit, and one run PVC FRLS insulated unsheathed copper conductor of size 1.5 Sqmm as earth continuity wire and connected to common earth dolly with copper including provn of of 1.2 mm thick pressed steel sunken terminal boxes 60mm deep suitable lenth and painted with red oxide primer in place of unserviceable shunken box complete for housing switches, regulators, bell push etc, complete all as directed for the following:-
One light / fan point controlled by one way piano switch 5 Amp.
One socket point 5 Amp on an independent board.
One socket point 5 Amp on same board
Point wiring controlled by two, two way switch.
All as per Ser item No 169.00 above but with cable of 2.5 sq mm for 15 amps Socket Independent board with other switches complete all as specified.
S & F switch piano ,flush type single pole, one way 5 amp, 2way 5 Amp bell push all as directed.
S & F switch piano ,flush type single pole, one way 6/15 Amps 5 pin complete all as speccified aand directed.
Supply and fix in replacement of socket outlet 2 in 1, 3 pin 5 Amps complete all as specified and directed.
Supply and fix in replacement of socket outlet 2 in 1, 3 pin 5 Amps and 15 Amps complete all as specified and directed.
S & F for celling rose 3 pin/pvc/ polycarbonate isolated body complete all as specified and as directed.
S&F batten holder insulated body with back plate inluding 12 watts LED lamp complete all as specified.
Supply and fix in replacement of stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required complete all as specified and directed.
S&F in replacement for LED tube light fitting of LED T5 tube lights (6500K) environomental freiendly energy efficient of 18/20 Watt LED including electric connection with PVC copper flexible twin core cable, 1.0 sqmm from ceiling rose to light fitting complete all as specified and directed by Engr-In-charge.
S & F in replacement LED street light luminaitres 20/25 watts with IP66 complete with pressure dia cast aluminium housing with GI pipe bracket made out of 25 mm dia medium grade pipe (60 cm long) bend to shape including fixing arrangement to wall with MS flat 25x3mm-2 Nos by nut, bolts and washers including electric connection with PVC copper flexible twin core cable 1.0 sqmm from ceiling rose to light fitting complete all as specified and directed by Engr-In-charge.
S&F in replacement for LED Batten with LED tube light integrated LED channel of capacity 10 Watt white colour complete all as specified and directed by Engr-In-charge.
M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to galvanised iron of 4 sqmm SWG earth wire fixed by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 40mm dia upto 3m height above ground level and water pipe 20mm dia GI medium grade with socket and plug 30 cm above ground level including earthwork, PCC chamber in PCC (1:3:6) type C-2 using 40mm stone aggregate, cast iron cover, wire meah etc all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009 complete and all as specified and direcrted by Engr-in-charge Note :- (i) 20 mm dia GI pipe for watering to be provided with a socket and plug and should be 30 cms above ground level. (ii) GI strip upto DBs earth connection is included in this item. (iii) GI pipe 40 mm dia protection pipe shall be provided upto Ground level.
S & F in replacement sheet metal enclosures for DBs double door type when MCBs to be used single pole & nuteral 8 ways complete all as specified and directed by Engg-in-Charge.
S&F in replacement MCB SPN 63 Amps, 240 Volts complete all as specified.
S&F in replacement MCB SP 6 to 40 Amps, 240 Volts complete all as specified.
M&L in replacement for submain wiring comprising single core, 2 Runs of 10 sqmm nominal cross sectional area multimultistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including appropriate dia. PVC conduits and conduit fittings not less than 25 mm dia complete, including provision of 1x10 sqmm nominal cross sectional area multimultistranded copper conductor cable PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS and specified and making good all disturbed work to match the existing complete incl taking down old UNSV sub main all as specified. Note :- Extra length of cables/ wire required for connection to MCBs shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly. Note : Two run of wire, one run of earth wire and PVC conduit shall be measured as one unit.
All as per Ser item No 174.00 above but 2 Runs of 6 sqmm nominal cross section and including provision of 1X6.0 sqmm nominal cross sectional area for earth wire complete all as specified and directed.
All as per Ser item No 174.00 above but 2 Runs of 4 sqmm nominal cross section and including provision of 1X4.0 sqmm nominal cross sectional area for earth wire complete all as specified and directed.
M & L cutting chases, pinning in, making god to facings where reuired and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed wiring etc, and making good, cutting not exc 10 cm girth in brick walls complete all as directed by Engr-in-charge.
Supply and fixing in replacement LT Main control board of CRCA sheet metal board made out of 2.0mm thick and painting with 2 coats with synthetic enemel paint over a coat of red oxide primer including copper bus bar and fixed on/inside wall for fixing arrangement of existing electronic meter incl internal connection with suitable size of copper conductor wire, and accessories, locking arrangement with opening handle (size not less than of box 100cmx80cmx25cm and adequate depth for the following equipments,internal wiring and termination of external cables, lugs and glands and conduit as required) including Taking down existing Old Unserviceable main control board comprising of following :- (a) Incoming :- MCCB 100 Amps, 4 Pole,415 Amps, 25 KA-01 No. (b) copper Bus bar 200 Amps for phase and neutral and earth bar. (c) Out going MCB SPN 63 Amps - 4 Nos. (d) Taking down Electric meter from existing distribution board and Re-fixing only existing electronic meter single phase 15 to 40 Amps, 240 Volts on new distribution panel- 04 Nos
S & F GI tube light grade galvanised of size 50 mm with all fitting and fixed to wall and celling or laid in floors for cable protection complete all as specdied and directed by Engineer-in- Charge.
S&F call bell ding-dong type, AC 230 Volts single pole complete all as specified.
Taking down/ dismantling complete ceiling fan of size 1200/1400 mm sweep down rod with its canopies, shackle, condenser housing with its rubber bushes, split pins, unscrewing the body parts of ceiling fan, taking out starter, rotor winding ball bearing, gun metal bush etc. complete to carry out the following repairs :- (a) Removing of burnt out fan winding and re-winding of motor with suitable size of copper enamelled wire, varnishing, heating as per manufactures design and directed and re-assembling complete ceiling fan fixing only old/new spare parts (i.e.) rubber bush of shackle and condenser housing, condenser, gun metal bushes, ball bearing, twin twisted copper cable, etc complete all as specified and directed by Engineer-in-charge. Note :- Ball bearing and Gun metal bush are measured and paid separately as supply only rates and fixing charges for spare parts shall deemed to be included in quoted rate.
S&F for Condenser 2/2.5 MFD.
S&F for rubber bush for shackle with bolt, nut and lock pin suitable for ceiling fan 1200mm/1400mm sweep.
Supply only ball bearing number of 6201/6202/6203/6204 as required.
Supply only gun metal bush as required.
Taking down/dismantling complete exhaust fans of any size for spray painting with two coat of synthetic enamel paint of approved colour including filling cavities with filler on coat after cleaning all dust etc. including re-assembling the same and testing after writing of MES NO on completion.
Taking down/ dismantling of defective/rusted storage type hot water Geyser of 50/35/25 Ltr capacity from different Qtrs of Bldg p-14 by disconnecting inlet/outlet connections and taking out unserviceable parts by unscrewing bolts and nuts, de-scaling/cleaning inner shell, servicing etc. Checking defects, re-assembling and re-installing the Geyser in position, connection and testing complete all as specified and directed.
Supply and fixing Plug and socket type DB (Functional Unit) 20 Amps capacity with provision of single pole 20 amps MCB, plug top and earth plug, grouted flush to walls complete all as specified.
M&L for painting of Geyser complete in site by scraping/removing old spray paint with brush/emery paper and spray painting with two coat of synthetic enamel paint of white colour and marking MES number with synthetic enamel paint of black colour in good and proper size all as directed by Engineer-in-Charge.
S & F GI tube light grade galvanised of size 40 mm with all fitting and fixed to wall and celling or laid in floors for cable protection complete all as specdied and directed by Engineer-in- Charge.
S&F for PVC flexible pipes 15mm dia (heavy duty) both end socketed 450mm long for hot/cold water.
S&F for copper (CP) hot water pipe for Geyser, connection with check nut and washer.
M&L for PCC preparation including cutting up to 45 cm width and depth of the road/hard standing and making good disturbed surfaces by using PCC type C2(1:3:6) by using 40mm graded stone aggregate for the fixing the pipe/laying cables complete all as directed by the Engineer- in-Charge.
Supply and fixing in replacement MCCB TPN/TP 100 Amps 415 Volts of braking capacity 36 KA of 3 pole confirming to (Adjustable Thermal and Magnetic Release Setting with short circuit settings) complete taking down and making necessary connections including all provisions for fixing in panel compartments as existing using necessary links of suitable metals and cleaning the terminals with CTC solutions complete all as specified and directed.
All as per Ser Item No 194.00 above but 63 Amps with braking capacity 36 KA.
M&L for Boring hole across the Road/plinth/hardstanding/path/drain/pavement etc., suitable for inserting HDPE/GI pipe of upto 100mm dia bore pipe for 0.4 mpa working pressure for cable passing without damaging existing Raod/path/hardstanding/floor by trenchless technology or manual using necessary equipment complete all as specified and directed.
RANDHIR AND COMPANY
MANCHANDA CONSTRUCTION CO
CHILLANA CONSTRUCTION COMPANY
M/s HANS BROTHERS
G S CONSTRUCTIONS
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .