AS PER TENDER NOTICE LOT 3

Providing and Laying Interlocking Pathways including Earthworks excavation, P.C.C 1:3:6 (1 Cement:3 C.Sand: 6 Graded stone aggregate 40mm nominal size), Kerb Stone with M-25 cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), factory made chamfered edge Cement Concrete 80mm thick cement concrete paver block of M-30 grade with approved colour, design & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand including cost of all material,labour and T&P etc. required for proper completion of work as per direction of Engineer-in-Charge

Providing and laying CC road including Earthworks excavation, P.C.C 1:3:6 (1 Cement:3 C.Sand: 6 Graded stone aggregate 40mm nominal size)in foundation , Class M-150 brick work in 1:4 (cement: coarse sand), Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade,Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site,With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25, cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge i/c Item of joint fillers, sealants, dowel bars, including cost of all material,labour, lead (50 metre) and lift and T&P etc. required for proper completion of work as per direction of Engineer-in-Charge.

Supplying and fixing of 16mtr high mast shaft of apporved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 3mm. Top dia minium 150mm bottom dia 360mm base plate 32mm thick suitable for wind velocity as pe IS 875 part 3& having no circumferential weld with accesories for high mast suh as head frame suitable for 6 to 12 luminaries & its control gear boxes 1.5HP power tool moter 3point suspension system with steel wire rope 6 mm dia double drum winch including making suitable foundation as per manufacture drawing/ site reiment along with foundation bolt nuts wahers anchors plates etc complee in all respect.

Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 170 to 200 Watt. Confirming to IP 66 protection complete in all respect.

Supply and Fixing 6 Sq. mm ISI marked, FRLS PVC insulated, single core copper conductor cable complete in all respect. as directed at site by Engineer in charge

Supply and Fixing 1.5 Sq. mm ISI marked, FRLS PVC insulated, single core copper conductor cable complete in all respect. as directed at site by Engineer in charge

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750mm below ground level over a cushion of 75mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect.10 sq. mm 3-1/2 core

Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect .40 A TPN

Supply and burring of Safe Earthing Electrode T-39 (Hot Dip Galvanized), Length up to 3000mm, outer pipe 76mm inner Dia 38mm terminal Dia 12 mm ,outer GI pipe of 16 SWG and inner GI pipe of 12 SWG with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonary housing. (From electrode terminal to switch board, cost of 25 X 3 GI. Strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified.

supply and fixing of twin unit aviation obstruction light (GEC-ZH 752) / Bajaj BJAOL-2 with red glass, B.C. holders etc. complete in all respect, at the top of the building complete in all respect