PROVN OF TOILET FOR TPS OFFICE AREA,SEPTIC TANK NEAR BLDG NO P-23,ADDN/ALTN OF DINNING ROOM BLDG T-61,TENSILE FABRIC SHED, VIEWCUTTER FOR BLDG P-28,VEGETABLE SHOP,MILK SHOP, STORAGE ROOM ACCN AND OTHER SANCTIONED WORK UNDER AGE B/R-II AT GE JHANSI

Amount

Surface dressing not exc 15 cm deep in Hard / dense soil complete all as specified and directed

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation ,shafts wells etc n exc 10 sqm on plan and getting out in hard/ dense soil complete all as specified and directed

M & L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed

M&L for treating the the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed

M&L for PCC Type D-2 1:4:8 ( using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed

M&L for TMT bars 5 mm dia and over upto and including 10 mm dia stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed

Use and waste of formwork for sides and soffits (if any) of concrete foundations, footing, bases of cloumns and plinth beam etc. for flat rough finished surfaces of concrete complete all as specified and directed

Use and Waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.flat rough finished surfaces of concrete complete all as specified and directed

Use and waste of Formwork to sides of pillars, posts, struts, piers, columns and stanchions flat rough finished surfaces of concrete complete all as specified and directed

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; n exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

M&L for RCC(Design Mix) M-25 grade (using 20mm mm graded stone aggregate) as Foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L for RCC (Design Mix) M-25 grade (using 20mm mm graded stone aggregate) as in columns, pillars, piers, post and struts, etc complete all as specified and directed

M&L for RCC (Design Mix) M-25 grade (using 20mm mm graded stone aggregate) as in roof beams, cantilevers, bressummers, lintels over 1.5m clear span, etc complete all as specified and directed

M&L for RCC (Design Mix) M-25 grade (using 20mm mm graded stone aggregate) in Roof Slab supported on walls, beams and columns in floors, roof, landings, balconies, canopies, in shelves and the like complete all as specified and directed

M&L for RCC (Design Mix) M-25 grade (using 20mm mm graded stone aggregate) as in chajja complete all as specified and directed

M&L for rolled mild steel Fe-410-W(Gde-E-250) quality B for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering, fixed with self tapping screws, complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces or brick walls or on concrete surfaces, finished surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 (in two layers 5mm thick setting coat mixed with WPC @ 3% by wt of cement over 10mm thick backing coat) , incl finished even and smooth, without using extra cement, Note:- [ Integral WPC will be measured and paid separately]

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 5 mm thick in cement mortar 1:3 on concrete surfaces like soffit of RCC slab/ceiling, chajja etc finished surfaces even and smooth (without using extra cement) complete all as specified and directed

Supply only Integral liqiud water proofing compound complete all as specified and directed

S&F powder coated aluminium window shutter Sliding type with frame of powder coated aluminium section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5.5mm thick coloured glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; complete all as specified and directed. Note : Glass Pan and Stainless Steel wire gauze shall be measure and paid separately.

S&F powder coated aluminium ventilator Louver type with frame , aluminium section weighting 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, side handles fixed to wall with fastener, etc complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted, or forged into spikes framed guard bars railing and similar works conforming to Fe 290. Gde-E165 complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n.exc 63mm deposited spread and leveled in layer n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed. .

M&L for 75mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) finishing surfaces even and smooth (without using extra cement) complete all as specified and directed.

M&L for moorum/red bajri in floors or paving laid in layers n exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed

M&L for 75 mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection and path laid in alternate panels not more than 3 mtr in length, laid to slope 1:30 including forming joints 10 mm wide and upto full depth of PCC and filled with bitumen mastic (1:3) 1 part bitumen 85/25 and 3 parts of sand complete all as specified and directed. {Note:-Rate is deemed to be inclusive of materials against forming & filling of joints }

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of exterior grade primer complete all specified and directed

M&L for preparation of new plastered surfaces of walls applying two coats of distemper acrylic emulsion white or tinted over a coat of chalk whiting primer over and including a layer of 1mm thick wall care putty on wall for getting smooth and even finish of surfaces, complete all as specified and directed

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying to coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S & F for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, quality confirming to Gde Fe-290 Gde E-165 complete all as specified and directed.

S&F to chowkats 35 mm thick 2nd class hard wood, plain framed paneled shutter (any number of panels) with panel of timber flat on both side (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

M&L for 35mm thick second class hard wood glazed & skeleton shutter for doors divided into squares (fully glazed or gauged) open rebated & prepared to receive glass, gauge etc (without sash bars) edges of framing, plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc, conforming to IS-1003 Part-I & II; size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) complete all as specified and directed.

S&F 100 mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed

S&F 200 mm long mild steel barrel tower bolt stove enameled black with bright bolt complete all as specified and directed

S&F 125 mm size mild steel pressed handles, oval type, stove enameled black complete all as specified and directed

S/F mild steel sliding door bolts 300mm clip & bolt type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate two on staple plate complete all as specified and directed

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F of 5.5 mm thick sheet tinted glass and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed including hacking out old glass complete all as specified and directed

S & F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

M&L for machine cut Kota stone slab flooring 18-20 mm thick and laid over and incl 15mm thick screed bed in CM (1:4) set and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with and including Cutting / Griding / mirror Polishing on Kota stone as per local trade practice, complete all as specified and directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over 10mm thick CM rendering in CM 1:4 complete all as specified and directed

M&L for Non skid ceramic colored tiles of size 300x300mm, 7 to 8 mm thick as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surface of size 450 X 300 x 7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and directed.

M&L for 18- 20 mm thick granite slab (any type) tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed. (Note:- granite in one piece to be used for treads in step with nosing at front and two no of grooves)

S&F 15mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (including necessary chasing and cutting for concealing) complete all as specified and directed

S&F 20mm bore galvanised mild steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (including necessary chasing and cutting for concealing) complete all as specified and directed

S&F 15mm bore long body bib tap fancy cast copper alloy chromium plated with crutch of butterfly handle, screwed down, high pressure for iron pipe or for brass ferrule complete all as specified and directed

S&F 15mm dia pillar taps fancy cast copper alloy chromium plated with crutch of butterfly handle, screwed down, high pressure for iron pipe or for brass ferrule cast copper alloy type complete all as specified and directed

S&F vitreous china wash basin, white flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed

S&F 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as directed.

S&F for PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed.

S&F for 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F for 15 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F for 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor, complete all specified and directed.

M&L for 100 mm dia Cast iron Nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

Supply and fix PVC connection 15 mm size with PTMT nuts of length 450 mm long complete all as specified and directed

S&F for grating square 150 mm size of PTMT (Minimum weight 100 gms) complete all as specified and directed

S&F 32 mm bore waste coupling of PTMT (half of full thread) (Min weight 45 gms each) complete all as specified and directed

S & F of bottle trap 32 mm size with 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all as directed. Make : Hindware / Cera / Parryware / Prayag Polymer

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing. The door frame shall be tied to the wall using 75/100mm long MS screw complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. M S tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed

M&L for 100 mm butt hinges stainless steel medium weight approved make ISI marked complete all as specified and directed.

S&F 125 mm aluminium alloy handles, cast type anodised complete all as specified and directed

S&F150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed.

S&F of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type , having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, complete all as directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions laid with torch application complete all as specified and directed by Engineer-in-Charge with following course of description below:- (a) 10 mm thick plaster in CM 1:4 with WPC (liquid water proofing compound @ 0.20 Ltr/bags(50 Kg Bag)) will be applied over the roof slab (subjected to condition as mentioned in notes) . After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based grout. After the surface is repaired the slab will be tested for water tightness again before proceeding with further treatment. (b) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners. (c) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/Sqm to be applied on prepared surface, till the surface is propely impregnated. (d) After the application of approved bituminous primer the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer's instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. (f) after apllication of APP membrane one coat of aluminium paint @ 0.20 Kg/Sqm over APP membrance will be applied Note : The cost of all items i.e. from Sr No. (a) to Sr No.(f) are included in quoted rate and no separate payment will be done for the above except liquid WPC.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed.

M&L for sand cushion over sub base, spreading and well ramming in layers not exc 15mm thick complete all as specified and directed.

M&L for 100 mm thick cement concrete type D- 2, 1:4:8 (40mm graded aggregate) for pavement of pathway complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour& pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for PCC Type 1:2:4 (12.5 mm Stone Aggregate) ,copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, kerb stop rounded or chamfered in edges complete all as specified and directed.

M&L for cement concrete in foundation filling and mass concrete type C2 1:3:6 (using 40 mm graded crushed stone aggregate) complete all as specified and directed.

M&L for Brickwork with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) on fair/other than fair faces of brick work finished even and fair complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 using 20 mm graded stone aggregate as in coping & in bedding & haunching against the side of wall of manholes complete all as specified and as directed.

Providing and fixing SFRC (Steel fibre Reinforced Concrete) cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter confirming to IS-12592, total weight of cover and frame not less than 182 Kg fixed in cement concrete 1:2:4 type B-1 using 20mm garded stone aggregate complete all as specified and directed

M&L DWCPE(SN8) 200 (OD)/175(ID)mm complete laid in trenches including earthwork, removal and return filling and jointed including testing alongwith necessary jointing material tees/ union / socket etc complete laid on PCC bed 150 mm thick PCC in 1:2:4 type B0 of avg depth 2.0 m including packing under and haunching against the side of pipes after they are laid and tested all as specified in IS 16098:2013 and as directed

M & L for ATT treatment to the soil alongwith external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall.

M&L for Formwork to chullah hoods, chajjas and similar items etc complete all as specified & directed by Engineer-in-Charge.

S&F mild steel TMT bars 6 to 8 mm dia & over for roof slab, cut to length bent to shape required, including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M&L for preparation of surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

S&F second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chemfered, put together with glue pinned at joints, supplied and fixed.

S&F 35 mm thick factory made 2nd class hardwood rail and styled plain framed panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commerecial veneering on both faces. The size of rail and stiles as per IS : 1003 (Part-I), klin seasoned and chemically pressure treated.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in floors finishing complete all as specified & directed by Engineer-in-Charge.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips or sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium ally fixed.

S & F vitreous china washdown water closet pan & trap (pedestal pattern) with plastic water closet seat black closet pattern with flat bottom and cover and mild steel chromium plated or aluminium hinginng device with flush pipe to pedestal pan incl all joints incl connection to drain pipe and flush pipe.

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, Vitreous China urinals, bowl type (back to corner wall type), complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe).

S&F 75 mm size PVC floor trap with grating incl jointing with solvent cement complete all as specified & directed by Engr-in Charge.

S&F 15 mm bore stop valves, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed.

S&F 4.0 mm thick figured glass, pin head type and glazing with oil putty in square n.exc 0.5 sqm in each pane.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 Kg/m incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc, complete all as specified.

Supplying and laying of 25 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in wall/trenches complete all as specified.

Supplying and laying of 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in wall/trenches and closed the end of existing line if required complete all as specified.

S&F Towel Rail 600 mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (min wt 190 gms).

Extra for forming fair finished to channel or drain 30 cm inner girth in cement concrete using extra cement including mitred/stopped ends, frames mould etc; complete.

M&L for providing pre cast reinforced concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) for man holes cover slab, set in CM 1:4 including necessary form work complete all as specified and directed

M&L for providing plain cement concrete type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in bed to drain pipes of 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S & F Salt glazed stone ware drain pipes of 150 mm dia grade ‘A’ laid in trenches and jointed and tested as specified.

S&F 500 Ltr rotational moulded poly-ethylene water tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I

Excavating in post holes (or similar holes) each n.exc 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surface in hard/dense soil complete all as specified and directed

M & L cement concrete 1:3:6 type C2 (using 40 mm graded crushed stone aggregate) as in filling and mass concrete, complete all as specified and directed

S&F steel work in tubular trusses, vertical post, struts, purlins etc incl special shaped washer etc., complete using ERW or incl butt welded tubes conforming to I.S. 1161-1998 grade St-240. complete all as specified and directed

M&L for Providing precast cement concrete 1:3:6 (Type C-1) as in kerb stone etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:6 complete with joints to match complete all as specified.

M&L for cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for laying in trenches 150mm bore reinforced concrete pipes, class NP2, laid and jointed with skeins of spun soaked in neat cement wash shall be inserted in the grooves at the ends of the pipes, the two adjoining pipes put against each other the collar is slipped over the joint covering equally both the pipes, more skiens of spun yarn soaked in cement wash shall be passed round the pipes and inserted in the joints by means of caulking tools after that cement mortar 1:2 slightly moistened shall be inserted in the joints finished in 45 degree slope complete all as specified and directed. Note:- After curing 7 days to the joints the sewage pipe shall be tested as per procedure laid down for water test.

Providing and fixing on site LLDPE septic tank conventional designed to carry sewage and sullage water, including excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 30 Users complete all as specified and directed. Make : Prince/Sintax or equivalent approved Note: The rate of earthwork i.e. excavation, returning, filling in and removal of any type of soil is included in this item and nothing extra will be paid on this account.

M&L for construction of soakage wells, including excavation in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8 M dia X 6.0 M effective depth complete all as specified and directed. Note: The rate of earthwork i.e. excavation, returning, filling in and removal of any type of soil is included in this item and nothing extra will be paid on this account

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chamberedframe, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.

Supply & Erection of tensile member structure as per drawings with following specification M. S. Frame- structure,1-Base plate 400mm x 400mm x 14mm Thick ,Anchor Bolt 16mmx600mm long ,Cloumn-130 mm outer dia 4.5mm thick ,Structure frame-76 mm Outer dia 3mm thick , Purlins 76mm Outer dia 3mm thik, ( all structure member should be Apollo /Tata/ SAIL/JSW make) Painting: - The MS frame shall be cleaned of dirt/grim and oil/grease deposits. The frame shall be sprayed with primer to finish. After primer, NC putty shall be manually filled at joints and dents if any. It will be wet sand papered to a smooth glossy finish. The ready surface will be painted with 2 or more coats of spray paint. ( ICI or ASIAN/Berger) Fabric: - High Quality Tensile Membrane silicon make of 750 GSM fabric welded on height frequency machine Tensile fabric to have following specification (a) Base fabric : 100% Polyster (b) Yarn : 1100 dtex (c) Weave : Plain weave (d) Total wight : 785 g/m2 (e) lacquering : SI FLUO PVDF both sides (f) Special feature : Low wicking (g) Breaking strength : 3000/2800N/ 5cm (h) Tear strength : 300 / 300 N (j) Adhesion 120 N/ 5cm (k) Flame retardancy M2/ B1 (l) Temperature resistance :- -30 OC / + 70 OC (m) Light fastness : 7.8 Note :- (1) Structure to be supported on tubular / square / rectangular section of ERW B-Class. MS pipes (2) The rate shall include supply & executing of all necessary jointing system of nuts & executing of all necessary joining system of nuts & bolts, base plate , etc (3) The rate should include cost of transportation of materials, crew charge, scaffolding and necessary labour charges for the entire job (4) The rate should include all the necessary civil works and structural works related to this. (5) the measurement shall be done as per plan area of structure (6) The work should be executed by specialised agency approved by Engr -in- Charge

S&F mild steel screw bolts 11 to 15 mm dia with hexagonal or square heads at one end and screwed the other or serewed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n exc. 0.5 cm , complete

Excavating over areas, n.exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed

M&L 100 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggt) as in floor including finished even and fair complete all as specified.

Forming 20 mm thick expansion joints filled with preformed bituminous filler & top 30 mm premixed & sealed with sealing compound grade 'A' in 100 mm thick.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm thickness comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws incl in this item)

M&L for MS work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles of Fe290 Gde E-165 complete all as specified and directed

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate as in bed blocks etc for embedding hold fasts complete all as specified and directed

M&L for box type steel window with 80x40x1.25 m MS tubular frame with side hung shutters ( double shutter for glass and gauze) jointed together with and incl grill using 12 mm square bar @ 10 cm C/C incl box type hinges with steel handle and steel pag stay complete glazing bars doweled and welded complete all as specified as directed. Note:- (a) The Glass / gauze shall be measured and paid separately. (b) Side hung Z-Section shutter shall be of size 20mm x 20mm x 25mm and 0.3mm thick.

M&L for light shade Vitrified ceramic coloured tiles 8 to 10 mm thick (Square or rectangular) polished,area of each tile not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in same colour grout to match over and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

S&F 18mm thick prelaminated WPC, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in any situation as in cup board shelves/shutter or similar work, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flap (when open) 30mm, complete all as specified and directed

S&F of stainless steel handles 100 mm size for kitchen cabinet shutters complete all as specified and directed.

S&F 140mm long ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed

S&F 3mm thick sheet glass ordinary quality type & glazing with oil putty in squares not exc 0.5 Sqm in each pan, complete all as directed.

M&L for soling (or sub base) 100mm spread thickness with crushed or broken boulders of grading 90 to 100 mm interstices filled surface formed and rolled and consolidated to required gradient and camber with 8 to 12 ton power roller complete all as specified and directed.

M&L for 150mm thick (compacted thickness) WBM in two layers of 75mm thick each with coarse stone aggregate of lime stone, sand stone, flint or quartzite of grading 2(63 to 40mm size) or of grading 3 (50 to 20mm size),spread, rolled and consolidated to gradient materials and camber required with 8 to 12 tonne power roller etc. complete all as specified and directed.

M&L for laying in alternate bays cement concrete work (not less than 150 mm thick) in pavement/ hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre complete all as specified and directed. (Note: The cost for use and waste of formwork for laying pavement concrete/ hard standing in alternate bays is included in the quoted rate).

M&L for Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified and directed.

M & L for edge stones to flooring with stone setts of size 250 to 300mm long x 150 to 200mm wide, and 450mm deep and sides dressed, bedded in cement mortar 1:3, joints 20mm thick, grouted in CM 1:2 with an admixture of metallic floor hardener 5% by weight of cement and stuck flush complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of electogalvanised terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed by Engineer-in-Charge for the following points:-

One light point controlled by one switch

One ceiling fan controlled by one switch

One exhaust fan controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per srl item no. 155 here-in-before but with 2.5 sq mm FRLSH copper wire with 2.5 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch .

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 4 sqmm + 1 run x 4 sqmm with FRLS insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed by Engineer-in-Charge. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

Notes for item No. 155.00 to 157.00 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

S&F, Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed.

S&F, Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed.

S&F, Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed.

S&F, Socket, two-in-one, 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed.

S&F, angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed.

S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

S & F 7W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed by Engineer-in-Charge.

Supply and fix LED lights fitting 1 x 20 W 4 feet, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and fix LED building security light fitting 25 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and as directed by Engineer-in-Charge.

Supply and fix of LED bulkhead luminaire in die-cast aluminium alloy body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection suitable for and including provision of 10W retrofit LED bulb, full white with B22 lamp holder complete all as specified and directed by Engineer-in-Charge.

Supply and fix of ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engineer-in-Charge.

Supply and fix of exhaust fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. including taking down existing unserviceable ventilating fan of any description complete all as specified and directed.

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge.

Cutting and screwing of existing steel tubing for alterations or additions of size 40 or 50 mm done in position without taking down and inserting tee branch connection complete all specified and directed by Engineer-in- charge.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed, 16 sq. mm nominal cross section, 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB distribution board, TPN, 4 way 415 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

S& F MCCB 4 pole 63 Amp, 16 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed.

Supply and fix MCB SP 6 to 32 Amp, 230 V `C curve 240V 50Hz complete all as specified and directed.

M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Yashoghan Construction (BID ID -3140361)