SPL REPAIR TO BLDG NO JP 120 01 02 05 06 JCOS ORS MD ACCN OF 642 EME BN BLDG NO 242 01 TO 04 OF

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified & directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L Brick work with FLY ASH brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified & directed.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete all as specified and as directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete all as specified & directed.

Demolition of cement concrete (un-renforced) in ground floor and paving not exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as specified & directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), 25mm thick, as in Sub base complete all as specified & directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L non skid ceramic tiles colored 300x300x7mm thick in floor set and jointed in neat cement slurry and pointed in white or coloure cement and over 20mm thick screed bed in CM 1:6 complete all as specified & directed

M&L for Non Skid white ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, Complete all as specified and directed by Engr-in-Charge.

Dismantling floor,hearth or wall tiling incl cement mortar bedding (but ot backing) , removing serviceable tiles to store and rubbish off the premises.

M&L Glazed ceramic coloured tiles in vertical surface 300x450x7mm/300x600x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed.

M&L Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types complete all as specified& directed

M&L machine cut kota stone slab flooring 18-20mm thick over 20 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

M&L machine cut kota stone slab 18-20mm thick in steps for riser, dado, skirting, wall etc over 20 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

M&L 75 mm thick PCC(1:3:6) type C1 (using 20mm graded stone aggregate ) as in plinth protection finished fair and even complete all as specified & directed

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L rendering 10mm thick in cement mortar 1:6 on fair faces of stone masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in CM 1:4 on stone wall surfaces or other than fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & fair without using extra cement complete all as specified.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand morrtar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed.

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment alongwith the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear meter incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors drilling and plugging holes etc all as specified and directed

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment of soil under existing floor using chemical emulsion 300mm apart incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors using emulsion @ 1 litre per hole complete all as specified and directed

M&L for preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of 1 mm thick wall care putty of approved tint complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified & directed.

M & L for preparation of newly plastered surfaces of walls and applying two coat of exterior emulsion apex paint (exterior grade) over one coat primer on walls complete all as specified & directed.

M&L for preparation of newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified& directed.

M&L complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of acrylic emulsion paint (exterior grade) over a coat of priming paint on walls all as specified & as directed.

M&L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of white wash complete all as specified& directed.

M&L for preparation of old plastered surfaces & applying one coat of white wash on ceiling complete all as specified & directed.

Treatement for sunken portion is as follows :- (i) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L for providing 12 mm dia holes of 40mm deep @2.00m c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry by pressure grouting for sunken floors of toilet , includind sealing the holes with CM 1:3, all as specified and as directed . (iii) M&L for water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement.(WPC will be measured and paid seperately). (iv) M&L for applyin evenly two coats of industrial bitumen 85/25 at the rate of 1.20 Kg/Sqm in each coat over vertical surfaces and floors of sunken floors of toilet including cleaning of surfaces. (v) M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc.

Demolition Mud in roofs, any thicknes, including plastering , APP membrane existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified& directed

M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified& directed.

M&L rendering 15mm thick in CM 1:4 with water proofing compound over green concrete surface (WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified& directed.

Supply only Integral waterproofing compound

M&L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 Kg/Sqm conforming to IS : 3384 and applying a layer of APP based polymeric membrane not less than 3mm thick weighing not less than 3.50 Kg/Sqm, reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) and upper side of membrane thermally insulated with white gravel finish uniformly embedded during manufacturing process. It shall be laid by torch application having side over lap 75 mm and at the end 100 mm, all overlaps and joints shall be sealed by torch application. For parapet, membrane shall be taken to a height of minimum 60 cm and inserted inside the parapet in a groove to a depth of 65 mm. The same shall be furnished by a membrane flashing, including two coats of aluminium paint over APP membrane Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified& directed by Engr-in-Charge.

M&L 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4,complete all as specified & directed.

Cutting holes in stone walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 exc half brick wall complete all as specified & directed.

Taking down chowkat or frame area not exc 1.5 Sqm each including cutting holes for hold fasts & making good complete all as specified.

Taking down chowkatts or frames exc 1.5 sq. m but n exc 4 sq m each complete all as specified& directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed.

M&L for Mild steel angle iron door frame 40mmx40mmx5mm conforming to Fe 410-0 (Gde-E-250 ) incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified& directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintel hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps,plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified & directed.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified & directed.

S&F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified& directed.

M&L Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified & directed.

M&L 25mm thick Prelaminated particle board, interior grade, prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified& directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified& directed.

M&L for preparation of old wooden surfaces over 10cm width or girth and applying one coat of synthetic enamal paint (of approved shade) complete all as specified& directed.

S&F Butt hinges 100mm long medium weight, colled rolled mild steel complete all as specified & directed.

S&F Butt hinges 75mm long medium weight, colled rolledmild steel for Prelaminated doors complete all as specified& directed.

S&F aluminium anodised barrel tower bolt 200 mm long extruded section and fixed

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed.

S&F 150mm 'D' type Aluminium handles, anodised complete all as specified & directed by Engr-in-Charge.

S&F 150mm Aluminium handles, cast type, anodised complete all as specified & directed.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and directed

S & Fixed 300mm Helical/rat tail door Spring 300mm size with MS sheet wing pattern including roller plate complete as directed.

S&F 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work etc. including taking down existing frame work complete all as specified & directed.

S&F in repairs 25 mm dia stainless steel curtain rod complete with SS brackets as required at site and SS side caps fancy type fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete all as specified as directed.

S & F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed.

S&F in repair for pressed steel shutter 1mm thick including pressed steel frame of 1.25 mm thick sheet, 12mm dia MS rod for locking, two Nos chromium plated handle and one Godrej pattern lock including two coat of spray painting over a shop coat of primer, complete, all as shown in Drg No. TD/2004/29 sheet No. 1/3 to 3/3

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

S & F for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed.

Supply only sheet glass ordinary quality,in squares n. exc. 0.5 SQM each 4.80 mm thick complete as directed.

S&F Sheet glass, ordinary quality, in squares exc 0.5 sq. m each pane 5.5 mm in thickness complete all as specified& directed by Engr-in-Charge.

S/F in repair kitchen sink without draining board made out of stainless steel 1mm thick with plugs, washers and waste pipe including bedding in cement mortar to dwarf wall or including and fixing cast iron cantilever brackets and connecting union to pipe over all size 495x420 mm bowl size 410x330x160 mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as specified & directed.

S&F in repair PVC waste pipe of 32mm bore of suitable length for WHB/Urinal/sink complete all as specified and directed

S&F in repair Stainless steel plate rack 1mm thick of size 900mm x 900mm x 250mm including fixed with rawl plug and screws on walls complete all as specified and directed by Engr-in-Charge. Make : Nirali

S&F Stainless steel plate rack, 1.00mm thick for kitchen size 600x900x230mm complete all as specified & directed.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified & directed.

Dismantling/demolition water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete all as specified & directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling water tanks complete all as specified& directed.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 20 mm dia complete all as specified & directed.

S&F brass Gun-metal, globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed.

Taking up or down 20mm steel tubing and connections, complete all as specified& directed.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed.

S&F 20mm GI tubing Medium grade fix to wall/floor complete all as specified & directed.

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed omplete all as specified & directed.

M&L for flat iron as in hold fast, hooks, cleats welded to angle iron door/window frames etc complete all as specified and directed

S&F white vitreous china wash hand basin 'Flat back/ Corner' of size 550x400mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete all as directed.

S&F 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as directed.

S&F in repair wall mixer chromium plated complete cast copper alloy, chromium plated, scrwed downhigh pressure, complete all as specified & as directed.

S&F in repair stop valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified & directed by Engr-in-Charge.

S&F in repair Stop/angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of Brass chromium plated complete all as directed by the Engr-in-charge.

Cutting holes into or through brick but in brick walls built, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime Ex 150 sq. cm but n exc 400 sq. Cm (not excluding 25CM depth) for cooler stand complete all as specified & directed.

S/F in repair Vitreous China Squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rests connection to trap and to flushing pipe, etc.complete including making food to floor complete all as specified & directed .

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, fixed in repairs, complete all as specified.

S&F in repair PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified & directed.

S&Fin repair PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&Fin repair PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified & directed.

S&F in repair PVC (SWR) bends any radius 110 mm bore complete all as specified & directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F in repair Grating doom 100 mm dia of PTMTwith/without hole (Minimum weight 25 gms) fixed with cement complete all as specified & directed.

S&F PVC (SWR) vent cowl 110mm complete all as specified & directed.

S&F in repair 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed.

S&Fin repair PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed.

M&L writing letters or figures(Block,roman,Italic or Indian letter n.exc 30cm high) complete complete all as specified & directed.

S&F brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position complete all as specified & directed.

S&F for Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified & directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming Fe 410 (Gde E-250 quality A) & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.

S&F M.S. frame work such as grills, gratings, angle frame etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stands and similar work conforming to Fe.290.Gde-E-165 a oat of red oxide primer after preparation of steel surfaces complete all as specified & directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in soft/loose soil complete all as specified & directed.

M&L for PCC Type D2 1:4:8 (40 mm graded stone aggregate) Cement concrete in foundations, filling and mass-concrete complete all as specified & directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggragate as in bed blocks, coping etc including weathering slightly rounded or chamfered angles and throating making grovves for fixing of man hole cover including necessary form work complete all as specified & directed.

Returning filling in incl spreading levelling watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified & directed.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified & directed.

M&L Concrete bed to drain pipes 150mm dia including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC(1:4:8) type D2 (using 40 mm graded stone aggregate) complete all as specified and directed.

M&L 150 mm Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed

M&L PCC(1:3:6) type C1 (using 20mm graded stone aggregates) in benching to manhole complete all as specified and directed.

Demolition of RCC (water tank) of any description and in any position not otherwise specifically provided for is reinforced (reinforcement cut as required to facilitate demolition) complete all as specified & directed.

M & L for precast RCC 1:2:4 type B-1(using 20mm graded stone aggregate) for manhole/drain cover including placing and set in CM 1:4 all as specified

M&L for RCC (Nominal mix ) in chajjas ,kitchen shelves Type B1 1:2:4 (20mm graded stone)

Form work to chulla hoods ,chajjas,troughs ,kitchen slab and similar items including edges

M & L mild steel (TMT bar)10mm dia and over cut to length bent to shape reqd, incl, cranking benching spirally for copying for columns hooking ends and bending with and including MS wire annealed wire not less than 0.9 mm dia.

All as per ser item No 129 above but 5mm to 10mm dia as in stirrups, spacers binders etc

Ditto- all as per item No 129 above but 6 to 8 mm dia TMT bars.

M&L Plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in landing, chajjas, shelves and similar articler as directed including necessary scaffolding complete all as specified& directed by Engr-in-Charge.

Dismanlting of kerb stone including cement bedding & removed off rubble.

M&L for 75 mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base of path/hardstanding complete all as specified & directed.

M&L 60mm thick machine pressed precast conctete coloured interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 , M-35 Grade and over 25mm thick sand complete all as specified and as directed.

M&L Precast cement concrete solid block /kerb stone factory made in PCC 1:2:4 type B-1 using (20 mm graded stone aggregates) set in CM 1:6(size of precast concrete block complete all as specified & directed.

M&L RCC Type B1 1:2:4 using 20mm graded stone aggregate in foundation including footing, plinth beam, base for column, etc complete all as specified and directed.

M&L RCC Type B1 1:2:4 using 20mm graded stone aggregate in for columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L form work to side of concrete foundation , footing , bases of columns, raft and raft beams, sides and soffits (If any) of foundation and plinth beams and similar work, vertical or to batter

M&L form work to side of pillar posts struts piers columns etc

S&F 4mm thick Aluminium composite panels of Alstrong/Eurobond/Duroboil or equivalent in combination with and combination of solid/metalic colours consisting of 3mm thick polyethelene resin(Thermoplastic core) of LDPE sandwhiched between 2 skinsof 0.5mm thick aluminium sheet (Alloy designation 310s) Making a total thickness of 4mm and with a tensile strength 16.67 Kg/cum. The skin shall be electrolytic colour anodizing of approved shade and colour for an anodic coating of minimum 20mirons)(+/-2 microns) & painted with PVDF paint coat(Kynar 500 or equivalent approved) of a minimum 25 micron thickness and bottom skin with a protective paint coat a per manufactures specification. The panel will be fixed in position with necessary fittings and fixturers on Mild steel frame work (squre/rectangular Hollow section ) fixing with screw complete all as specified and directed. The joints of panels will be filled with sillicon sealent to create a waterproof sealn and prevent moisture infilitration complete all as speciied and directed. Steeel frame work will be maesured and and paid seperately

S&F stainless steel work as in door /gate (ornamental type) design will approved by GE, made out of hallow/square/rectangular/circular section and other covering door to be prepared for handing or sliding with including either hooks , fittings complete all as specified and directed by Engineer in charge.

Supply & fixing stainless steel (gde 304) letters made of hollow tubes, plates including welding, grinding, buffing polishing fittingas per size and design approved by GE with necessary frame work whrere required, made of mild steel hollow section of 25 mm SQ pipe , nesessary accessories required for fixing and in any position up to 9 mtr height. all steel surface will be painted with two coats of synthetic enemal paint. for mearurement purpose height of the each word will be measured.

Excavation in post holes (soft/loose soil) each n.exc.0.5 cum, getting out, RFR in and ramming earth or broken rubble mixed wth earth around in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc. 50m.

M&L PCC (1:3:6) type C-2, using 40 mm graded stone aggregate in foundation filling /mass concrete as in post hole

S&F structural steel work as in roof truss made of MS hallow section for pulines , crane , gantries,rails, and cercular/rectangular frame work for fixing of ACP Board for gates Pillars fastenings and heavy brackets, framing (Beam, tee, angle, chanel or flat section including necessary cutting welding notching complete all as specified and directed

S&F structural steel as vertical post or single stanchions made of MS hallow round/square pipe medium graded frame plates , caps , bases , splices, angle brackates , cleats and other connections complete all as specified and directed

S&F plates (Plain or chequered ) Chanels square cut or notched (ordinary and counter sunk) forming holes, without any attachment

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws as specified

Suface excavation n exc 30cm deep and averaging 15cm deep in any type of soil

S&F in repair brass chromium plated towel ring incl a pair of CP brass bracket complete all as specified and directed by Engr-in-Charge.

M & L for brick work with subclass “B” Old size bricks, straight or curved on plan,to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

S&F PVC (SWR)110mm Branch piece (single Y ) equal or unequal

S&F Stainless steel plate rack 1.00 mm thick for kitchen size 600x900x250 mm fixing with stainless steel screw on wall properly complete all as specified and directed.

M&L for 100mm thick Cement concrete type B-1, 1:2:4 (40mm graded aggregate) all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for

Taking down carefully copper/Aluminium point wiring for light/fan/socket/light fitting/power point and taking down of teak wood batten / PVC casing caping/PVC conduit/steel conduit and making good disturbed surfaces of walls/ceilings /floors etc incl dismentling of fittings.

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke and halogen (FRLSH) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20 mm external dia) but shall be increased as per actual site requirement in accordance with clause No. 19.125 of SSR Part-I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLSH PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0 mm thick for one light point controlled by one way switch including cutting chasis in stone/brick wall as required on site all as specified & directed.

All as per item No.160 here-in-before but for one fan point controlled by one switch and regulator

All as per item No. 160 here-in-before but for one exhaust point controlled by one switch .

All as per serial item No. 160 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No. 160 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per item No 160 here-in-before but for one bell/buzzer point controlled by one bell push

All as per item No.160 here-in-before but for one light point controlled two ,two way switches

All as per serial item No.160 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

All as per serial item No.160 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts.

S&F switch piano flush type single pole two way 5 Amps 230 Volts .

S&F bell push flush type 5 Amps 240 V complete all as specified & directed.

S&F bell/buzzer AC 230 volts single pole complete all as specified & directed.

Supply and fixing switch piano, flush type, single pole, one way, 15 Amp, 230 Volts.

Supply and fixing socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts.

Supply and fixing socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts.

Supply and fixing ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified.

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part STOUTPLUS600BS20WLED840SPCWH

Supply and fixing LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete including all as necessary fitting accessories complete all as directed. Make : Philips/Havells/Crompton

Supply and fixing lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

Supply and fixing sheet metal enclosures double door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar,8 way, 240 Volts.

S & F MCB 32/40 Amp, single pole & neutral,240 Volt complete all as pecified & directed.

S & F MCB 6-40 Amp, single pole 240 Volt complete all as pecified & directed.

Supply and fixing Vertical sheet metal enclosures double door type , suitable for fixing MCB, TPN with 200 amps rated bus bar , 4 way. 415 Volts with inbuilt MCCB 4 pole 63 Amp,16 KA

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cable fire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note: Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length)

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed. Note : - Quoted rate shall be deemed to include for earth wire with protection pipe up to 7.5 meter length.

Disconnecting form elect connection and taking down carefully the existing electric energy meter of any capacity, any make,any size and depositing same the electric energy meter in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same inside the Old Meter inside Box carefully incl necessary electric connections complete all as directed.

Disconnecting form elect connection and taking down carefully the existing Ceiling fan/Exhaust fan/Geyser of any capacity, any make,any size and depositing same the Ceiling fan/Exhaust fan/Geyser in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same Ceiling fan/Exhaust fan/Geyser carefully incl necessary electric connections complete all as directed.

M/L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore

Supply and fix ceiling fan complete with electronic type regulator , copper winding and accessories 230v 1200mm sweep BEE 5 star rated with brushless direct current motor (BLDC) including taking down old unserviceable ceiling fan complete all as specified and directed by engineer-in-charge.

S&F in repair cubical metallic box of size 1.00m x 0.90m x 0.30m depth made out of 2mm thick mild steel sheet, front openable, double door with locking arrangement with & including 3mm thick plain sheet clear glass of suitable size fixed to facilitate meter reading, all internal & external steel surfaces painted with two coats of synthetic enamel paint over a coat of red oxide primer, internal wiring with PVC insulated single core multistranded copper conductor FRLS cables IS-694 marked of adequate size but not less than 6 sqmm with proper ferrule & cable gland, box shall be fixed on wall with ‘Anchor’ type /fastener type bolts & nuts (Set of 6 bolts of 12mm dia 200mm long with nuts & washers) grouted into the wall properly to hold the box, writing MES No/Qtr No for each energy meter with thick white synthetic enamel paint, Neoprene rubber gasket shall be provided for proper sealing, box shall have arrangement for fixing electric energy meters – 04 Nos, MCB DB TPN 4 way -01 No complete all as directed.

Supply and fixing in repair of GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the following sizes :- (a) 25 mm bore Note :-excavation earth work will be measured and paid saperatly.

Supply and fixing in repair of GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the following sizes :-(a) 20 mm bore Note :-excavation earth work will be measured and paid saperatly.

Supply and fixing in repair of GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the following sizes :- (a) 15 mm bore Note :-excavation earth work will be measured and paid saperatly.

supply and fix exhaust fan metal body AC single phase 230/240 V of size 300 mm sweep with louver including making suitable opening/hole in wall all as specified and directed by ebgineer-in-charge

Taking down Unserviceable DB TPN/SPN any type any capacity complete and making good to disturbed surfaces of wall.

Supply and fix ceiling fan regulator electronic step type 230 Volts single phase all as specified and directed.

Taking down submain wiring cable any number of runs alongwith earth wire from the existing concealed or surface conduit and offering credit as per schedule of credit all as directed. Note : Any runs of cable and earthwire will be measured as one unit length.

M&L for submain wiring with 4 run of 6 sqmm single core copper conductor PVC insulated cable and 1 run of 6 sqmm single core copper conductor insulated cable as earthing lead drawn through PVC conduit all as directed. Note:4 run of 6 sqmm cable and 1 run of 6 sqmm cable together will be measured as one unit length.

Supply & fix Inverter rechargeable LED batten tube light along with fixture, 3feet long, 1x20 W AC ,Energy saving, back up up to 4 hrs, power ful lithium battery-5600 mah, long battery life-500+ rechage cycle charging time 8-10 hrs including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Halonix, Havells, philips, wipro or equivalent

Supply & fix in repairs LED 10 watt B 22 inverter rechargeable LED T-bulb complete all as specified and directed Make: Philips, Halonix, Havells, wipro or equivalent

Supply and fix batten Holder PVC/polycarbonate type with cord grip cap suitable for pendent fittings ISI marked, all as specified and directed.

M&L for rewinding ceiling fan 1200/1400mm sweep with super enamalled copper wire of exisiting gauge including insulation material varnishing and drying all as directed.

S&F in repairs MCB DB TPN 8 Way double door 415 Volts all as specified and directed.

Supply & fix in repairs MCB TPN 63 amp, 230 Volts, Single phase, 10 KA Capacity all as specified and directed.

M&L for earthing complete with galvanized steel earth plate 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check-nuts, and washers of galvanized iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, GI pipe light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point of galvanized Iron/steel of size 75 x 75 x 25 mm, supplying and laying charcoal dust, common salt, PCC 1:2:4 type B-1 chamber and MS angle iron frame 40 x 40 x 3 mm and RCC cover 40 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia, GI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in Plate No. 3 of SSR Part I of 2009 and connected to earth test point including testing complete all as specified & directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 50 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified. Note :- Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M/S RAJESH KUMAR & SONS (BID ID -3292455)