NIT NO: 1121/TC/2025-26

2.3 Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned including all leads and lifts removal and disposal of top organic soil not exceeding 150 mm in thickness if required and as per relevant clauses of section-200. A In area of light jungle Hectare 61253.00

Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing graded Material, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401. Plant mix method (with Mechanically crushed stone only) (b) For Lower Sub-base with (i) Grading-V Material

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per clause 406.

Prime coat Providing and applying primer coat with bitumen emulsion (SS-1, grade confirming to IS:8887) on prepared surface of granular base including clearing of road surface and spraying primer using mechanical means as per clause 502. (i) on WBM / WMM surface @0.85 kg/ sqm.

Tack coat Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom and as per clause 503. (ii) Granular surface treated with primes @ 0.30 kg/ Sqm

5.3 Bituminous Macadam Providing and laying bituminous macadam as per clause 504 with mixed prepared in minimum 40-60 TPH capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction. (ii) for Grading II (19 mm nominal maximum size aggregate, bitumen content 3.40%) Cum.

Close Graded Premix Surfacing/Mixed Seal Surfacing Mechanical means using minimum 40-60 TPH capacity of HMP. Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness using bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade, complete as per clause 508.II. With mechanical paver finisher A With bitumen ii) Type B ( 13.2 mm to 0.09 mm size aggregates ) Sqm.

6.3 Providing and laying cement concrete for plain concrete/ reinforced concrete i/c form work, shuttering complete in as per drawings and specifications.( For Village roads ) (i) P.C.C. M-10 Cum.

Providing and laying Un-reinforced Cement Concretc. Without Dowel bars incliding fromwork and expansion, contraction & longitudinl joints as per design and as per IRC-62-2014, over a prepared base a per approved mix design and finishing to lines and grade as per Drawing for Pavement thickness less then 200mm in Low Volume Roads. PCC Grade M 30 with minimum Cement Content @375Kg/cum

Providing and laying cement concrete for plain concrete/ reinforced concrete i/c form work, shuttering complete in as per drawings and specifications.( For Village roads ) (ii) P.C.C. M-15

Providing and fixing guard stones 200 x 200 x 900 mm made of precast RCC M20 grade fixed at 300 mm into the ground in P.C.C. 1:3:6 blocks of size 400 x 400 x 400 mm and given two coats of paint with white and black bands including excavation

Kilo Meter Stone (Reinforced cement concrete M15grade kilometer stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) (i) 5th kilometer stone (precast)

(ii) Ordinary Kilometer stone (Precast)

(iii) Hectometer stone (Precast)

Providing and laying Reinforced Cement Concrete pipe NP 3 / prestressed concrete pipe on first class bedding Laying Reinforced cement concrete pipe NP3 /prestressed concrete pipe complying to IS:458, with ends casted as per the requirements of flush jointing of pipes for culverts on first class bedding of granular material including joints duely filled and finished with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets. B 600 mm dia

Boundary pillar Reinforced cement concrete M15 grade boundary pillars of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per clause 807.

Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material as per Clause 304, loading the unserviceable material in tipper and unloading with all leads & lifts as directed by Engineer-in-Charge. Ordinary soil upto 3 m depth

Plain cement concrete complete as per drawing and Technical Specifications (i) PCC Grade M 15

(ii) PCC Grade M 20

Providing and laying Reinforced Cement Concrete pipe NP 3 / prestressed concrete pipe on first class bedding Laying Reinforced cement concrete pipe NP3 /prestressed concrete pipe complying to IS:458, with ends casted as per the requirements of flush jointing of pipes for culverts on first class bedding of granular material including joints duely filled and finished with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets. D 1000 mm dia

Providing 1st class bedding below pipes with graded sand or other granular materials passing through 5.6 mm sieve as per clause 2904.

Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification as per clause 2503.

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification 710.1.4 of I.R.C. 78 and 2200 (i) Granular material

Construction of RCC drain/chamber/cover, placing in position, providing shuttering and concreting by using concrete mixer, compaction by vibration etc complete as per drawings and technical specifications excluding reinforcement. with RCC M-20 Cum.

(iii) Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in drain/cover/chamber complete as per Drawing and Technical Specifications.

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead upto 1000 meters and as per relevant clauses of section-200 in (i) Lime / Cement Concrete B Cement Concrete Grade M-15 & M-20

(i) Lime / Cement Concrete C Prestressed / Reinforced cement concrete grade M-20 & above

Excavation for Structures Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material including dewatering etc. complete. I Ordinary soil (i) Upto 3 m depth

II Ordinary rock (not requiring blasting)

Add extra 20% in the rates of above items for dewatering (Assessment of dewatering shall be made as per site condition ) The cost of shoring and shuttering, where needed, be added @ 1 percent on cost of excavation for open foundation.

Sand Filling in Foundation Trenches as per Drawing & Technical Specifications.

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications. A Using concrete mixer (i) PCC Grade M15

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 (Newly laid concrete shall be covered by gunny bags). A Height upto 5m (a) Using concrete Mixer (ii) P.C.C. Grade M-20

D Height upto 5m (b) With Batching Plant, Transit Mixer and Concrete Pump (i) R.C.C. Grade M-20

Supplying, fitting and placing HSD (High Strength Deformed Steel) bars reinforcement in sub-structure complete as per drawing and technical specifications section 1600 and 2200

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification sections 1500, 1600 and 1700 (Newly laid concrete shall be covered by gunny bags). (b) Using Batching Plant, Transit Mixer and Concrete Pump (i) Height upto 5m

Supplying, fitting and placing HSD (High Strength Deformed Steel) bar reinforcement in super-structure complete as per drawing and technical specifications

Providing and fixing in position tar paper bearing for slab as per approved drawings and specification sqm

Providing weep holes in Brick masonry/ Plain/ Reinforced concrete abutment, wing wall/return wall with 100 mm dia. AC pipe, extending through the full width of the structure with slope of 1 V: 20 H towards drawing face. Complete as per drawing and Technical specifications section 2706 and 2200.

Drainage Spouts complete as per drawing and Technical specifications of section 2705

Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications as per relevant clause of section 2700.

Construction of RCC railing of M30 Grade in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequate space between vertical post for expansion, complete as per approved drawings and technical specifications. (vide drawing No. SD/201, SD/304)

PCC M15 Grade leveling course below approach slab complete as per drawing and Technical specification and as per relevant section 2700

Providing and laying M-30 grade Reinforced cement concrete approach slab including reinforcement and formwork complete as per drawing and Technical specification and as per relevant sections 1500, 1600, 1700 and 2704

Filler joint B Providing & fixing 20 mm thick compressible fiber board (12 m long x 25 cm deep ) in expansion joint complete as per drawing & Technical Specification.

Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specifications 710.1.4 of I.R.C. 78 and 2200 cum

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification 710.1.4 of I.R.C. 78 and 2200. (i) Granular material

Providing and fixing in position tar paper bearing for slab as per approved drawings and specification.

Granular Sub-base as per Table:- 400-1 Construction of granular sub-base by providing graded Material, , carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401 (b) For Sub-base cum drainage layer or upper sub-base with (ii) Grading-VI Material

8.4 Retro- reflectrorized Traffic signs as per Clause 801 Providing and fixing of retro- reflectrorized cautionary, mandatory and informatory sign digitally printed over reflectrorized sheeting of required grade confirming to ASTM D 4956 including covering with transparent sheeting (lamination sheeting) to protect from fading and damage due to wheather effect as perClause 6 of IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminum/ Aluminium Composite Material (ACM) sheeting including application of fluorocarbon coating applied on exposed surface of aluminium to ensure corrosion resistance, supported on a mild steel back frame of ISA 40 x 40 x 5 mm and mild steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paints or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.) C. Made of Class-A High Intensity Mirco Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-2022 (for ODR & Village Roads) a) With Aluminium Sheeting of 2 mm thickness (i) 900 mm equilateral triangle

800 mm x 600 mm rectangular

900 mm high octagon

750 mm high octagon

Providing & Fixing tree studs in Square/ Round shape of 4” side/diameter made of Grade-C retro-reflective sheeting of Type-XI fixed on 2 mm aluminum sheeting (Confirming to IS:736-Material Designation 24345 or 1900) as specified in section 801.3 of MORT&H and fixing the same with four Nos. high strength nails confirming to 1S:1367 on trees at site each.

Providing & Fixing Hazard Marker type 2 Partial Reflective hazard marker as per clause 15.66 of IRC 67-2022, made of 16 gauge (1.6 mm) thick mild steel sheet Confirming to IS: 2062 Painted with one coat of Zinc Chromate Stoving Primer and two coats of Black Stove Enamel (Oven Baked) paint with 10 cm alternative bands of yellow Retro- Reflective Sheeting of Micro Prismatic Grade pasted as per IRC:79 and black paint, including back frame made of angle iron 25x25x3mm mounted over one MS angle Iron post of size 50X50X6 mm of 1.65 meter long duly painted with synthetic enameled paint block including bolts and fixing the same in M-15 concrete black of size 30X30X30 cm Including transportation etc. Complete B Made of Class-B Micro Prismatic Grade Sheeting of Type XI (for MDR, ODR & Village Roads) Each

8.6 Direction and Place Identification signs upto 0.9 sqm size board as per Clause 8.1. Providing and erecting direction and place identification retro- reflectrorized sign Digitally Printed over reflectrorized sheeting of required grade confirming to ASTM D 4956 including covering with transparent sheeting (lamination sheeting) to protect from fading and damage due to wheather effect as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminum sheeting / Aluminium Composit Material (ACM) Sheeting including application of fluorocarbon coating applied on exposed surface of aluminium to ensure corrosion resistance, supported on a mild steel back frame of ISA 40 x 40 x 5 mm and mild steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, 60 cm below ground level as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paints or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.) C. Made of Class-A High Intensity Mirco Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-2022 (for ODR & Village Roads)

Direction and Place Identification signs with size more than 0.9 sqm size board as per Clause 8.1. Providing and erecting direction and place identification retro- reflectrorized sign digitally printed over reflectrorized sheeting of required grade confirming to ASTM D 4956 including covering with transparent sheeting (lamination sheeting) to protect from fading and damage due to wheather effect as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminum sheeting / Aluminium Composit Material (ACM) Sheeting including application of fluorocarbon coating applied on exposed surface of aluminium to ensure corrosion resistance, supported on a mild steel back frame of ISA 40 x 40 x 5 mm and mild steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paints or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.) C. Made of Class-A High Intensity Mirco Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-2022 (for ODR & Village Roads)

8.26 Providing painting figuring and numbering to culverts upto 6 m span complete as per IRC specifications. Each 307.00

Providing painting figuring and numbering as per IRC specification complete for (i) 5th kilometer stone

Ordinary Kilometer stone

Hectometer stone

Boundary stone

8.38 Metal Beam Crash Barrier A Type - A, "W" : Metal Beam Crash Barrier Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanized by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811.3. Meter

UOM Name

Percentage

Per mile

Siemens Per meter

Item Code