Shifting and erection of Transformer along with all fittings from existing Four Pole structure to Two Pole structure at Ash Recovery Pump House Area

Amount

Supply of 'A' Structures for 11 KV Take off with top mounted AB Switch and provision of Lightening Arrester (Galvanized)

Supply of MS Channel AB switch(100x50x6 mm) GALVANIZED

Supply of Clamp for AB switch base channel (50 x 6mm) (1 Set for 2 pair) for 9 meter 400 KG PSC pole (Galvanised)

Supply of Male female contact of 11 KV AB Switch 200 Amp

Fixing and fitting of 11KV AB Switch on DP with all hardware fitting used for sectional listing of Line as per direction of Engineer I/C

Supply of MS channel (75 x 40 x6 mm) for supporting H.G. fuse & L.A. set (Galvanised)

Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Supply of 11 KV D.O. Fuse unit (porcelain type)

Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts,washers etc. as required.

Supplying, installing, testing and commissioning of following capacity 63 Amperes TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required.

Supplying of two lengths of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) double pole cross arm for three wire 11KV over head line conductors complete with through bolts and nuts for clamping to the poles, 50 mm X 6 mm M.S. flats welded on one side to the channel iron and with bolts and nuts on the other side for tying the cross arms together, including drilling holes for insulator pins/ fittings, bolts, nuts and washers etc (as per drawing) and painting with primer and finish paint as required.

Supply of Transformer base channel (100 x 50 x 6)mm Galvanised

Clamp (50 x 6mm) for transformer base channel Galavanised (1 Set of 2 pair)

Transformer Belting (50 x 50 x6 mm) and belting support (40 x 40 x 6mm) Galvanised

Clamp (50 x 6mm) for transformer belting Galavanised (1 Set of 2 pair)

Supply of 11 KV H.G. Sets

Fixing and fitting of Horn Gap fuse set and fitting of HT pin insulator of Horn

Erection of 100KVA Substation Transformer

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Erection of ACSR conductor of 7/3.35 mm to 7/4.00 diameter and above including binding etc. as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

M S Nuts & Bolts of different size

Transportation and hiring charges of Hydra, JCB etc.

Anticlimbing Device(Barbed wire) 2x12 SWG

Supply of 35 mm X 55 mm X 4 mm Galvannised slotted/angle iron/ channel.

Supply of Stone aggregate (single size) 40mm nominal size

Paintaing of transformer by removing white or colour wash by scrapping and sand papering and preparing surfaces smooth including necessary repaires to scratches etc. complete. Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacturer. Painting of two coats with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.

UNIFIED POWER PRIVATE LIMITED

M/s. GOPAL MISTRY