Provn of rain water harvesting with check dam near firing range of HQ 22 Sector Assam Rifles at Jwalamukhi

Amount

SCHEDULE 'A' PART-I (Provision for RCC Check Dam for rain water harvesting at HQ 22 Sect AR at Jwalamukhi)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m in all kinds of soil

Providing and laying in position Plain cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering, all work up to plinth level.

M/L 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement

Centering and shuttering including strutting, propping etc. and removal of form for walls L = 2(34.00+2.00) = 72.00

Steel reinforcement for R.C.C. work incl straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade , one or more coats on old work

SCHEDULE 'A' PART-II (Provision of Pump House (PFTs) at HQ 22 Sector AR)

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavatedearth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m in all kinds of soil.

Providing and laying in position Plain cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centering and shuttering, all work up to plinth level.

Providing and laying in position 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for column

Centering and shuttering including strutting, propping etc. and removal of form for Plinth Beam

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m²

Rendering on fair faces of brick work 15mm thick with CM (1:4) External surface (below plinth level ) 0.45m high (230mm th wall)

M&L hardcore of gouge exc 45mm but n.exc 90mm

M&L PCC 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

M&L PCC 1:2:4 (1 Cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size) as in flooring the surface even and smoooth

M&L PCC 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) as in plint hprotection complete all as specified

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws 30 mm thick shutters With ISI marked stainless steel butt hinges of required size, Kiln seasoned and chemically treated hollock wood

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 150x10 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete 20 mm dia

M&L preparation of surface and applyingn /Finishing walls with water proofing cement paint of required shade New work (Two or more coats applied @ 3.84 kg/10 sqm)

Painting wood work with Deluxe Multi surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete, Hot finished welded type tubes

SCHEDULE 'A' PART-III (Provision of Electrification for Pump House (PFTs) at HQ 22 Sector AR)

S/F for point wiring for light point/fan point/exhaust fan point /call bell point with 1.5 sqmm FR PVC insulated copper conductor single core cable in surface/recessed PVC caping cashing with piano type switch, phenolic laminated sheet suitable size MS box and earthing teh point with 1.5 sqmm FR PVC insulated copper conductor single core cable etc as reqd

M/L for point wiring light/power plub with 2x4 sqmm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 No.4 Sqmm FR PVC insulated loop earthing as reqd

Installation, testing and commissioning of pre-wired flourscent fitting/compact flouroscent fitting of all types , complete with all accessories and tube etc directly on ceiling/wall, including connection with 1.5 sqmm FR PVC insulated copper conductor, single core cable and earthing etc as required

Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sqmm FR PVC insulated copper conductor, single core cable, including providing and fixing laminated sheet cover on the the fan box and carriage of ceiling fan from store to site etc as reqd

Installation, testing and commissioning of ceiling fan regulator, in existing switch box inclunding connection with 1.5 sqmm FR PVC insulated, copper conductor, single core cable, earthing the regulator etc as reqd

Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch connection, painting etc as reqd

Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 amps and 5/6amps modular socket outlet and 15/16 amps modular switch connection, painting etc as reqd

M/L for 5 amp to 32 amp SPN rating 240 volt 'C' series MCB suitable for lightning and other load of poles.

S/F of 3 pin, 5 Amp ceiling rose on the existing juction box incl connection etc as reqd

S/F brass batten/angle holder incl connection etc as reqd

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,"C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with nections, testing and commissioning etc. as required 63Amp

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MC B/RCCB /Isolator) :12 way, Double door

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required : 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

SCHEDULE 'A' PART-IV (Provision of Brick Masonry Water Tank at HQ 22 Sector AR)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Providing and laying in position cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - All work up to plinth level

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

20 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 48.30mm OD steel tubes

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/ m²

SCHEDULE 'A' PART-V (Provision for pipe line with pump set for rain water harvesting at HQ 22 Sector AR)

Providing and fixing 65mm dia nominal bore GI pipes complete with GI fittings including trenching and refilling etc.

Providing and fixing 65 mm nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end)

Providing and fixing 65 mm nominal bore Vertical gun metal non- return valve of approved quality (screwed end)

Providing and fixing 65 mm nominal bore G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25mm x 5mm copper strip at 0.50 metre below ground as strip earth electrode incl connection/ terminating with nut, bolt, spring, washer etc as reqd (jointing shall be done by overlapping and with two sets of GI nut bolt & spring washer spaced at 50mm)

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size upto 35 Sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as reqd.

Supply only XLPE power cable of 1.1 KV grade of sizem4 x25 Sqmm

Providing, Installation, commissioning and testing of centrifugal multistage water pump set of capacity 30 HP, head range 48-69 M, three phase (Make - Crompton Greeves, KSB, Kirloskar)

Providing, Installation, commissioning and testing of Panel board suitable for 30 HP centrifugal multistage water pump set (Make - Crompton Greeves, KSB, Kirloskar)

SCHEDULE 'A' PART-VI (Site Development)

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge All kinds of soil

Shree Meghalaya Construction & Supply Co.

M/s Ravina Enterprise

MEGHALAYA CONSTRUCTION AND SUPPLY CO.