CA No GE/H-02/2022-23 SPL REPAIR OF ONCOLOGY-II FEMALE WARD AT AHRR UNDER GE E/M RR HOSPITAL DELHI CANTT-10

Amount

Demolition of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

M & L for non-skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid incl over 15mm thick cement screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M & L for glazed ceramic digital coloured tiles 600x300x8 to 9 mm thick in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick rendering in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M & L for 18 to 20mm thick granite of any type (table rubbed & polished) in jambs, pillars, window cills, plate forms, steps, crumple joints in CM (1:4) including pointing in white cement (1:2), using marble dust with admixture of pigment to match with shade of granite incl 15mm thick screed bad or backing layer in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid incl over 15mm thick cement screed bed in CM 1:6 complete all as directed.

Dismantling of wall and ceiling board of any description, any thicknes including cover fillets and frame work complete all as specified and directed by Engr-in-Charge.

M&L for exposed GI frame/grid system duly powder coated for module size of 600 x 600 mm suitable for lay-in aluminium / mineral fibre ceiling tiles, having main T runner of 24 mm size, suspended at 1200mm C/C and cross T runner of 24 mm size, suspended at 600mm C/C with interlocking arrangements to form grid of 600 x 600mm, perimeter runner/channel of 15 mm size, main and cross T runner supported by 4mm dia GI rod from slab / Roof, wall angle etc with and including all fixing accessories and making good of distrubed wall surfaces complete all as specified and directed by Engr-in-Charge.

M&L for metal false ceiling, lay-in type, 0.5 mm thick, having tegular edge profile, duly powder coated, perforated type with glass fibre acoustic fleece, suitable for false ceiling grid/frame module of 600 x 600mm size, complete all as specified and directed by Engr-in-Charge.(Note : The grid /frame shall be measured and paid for separetly.)

Supply & fixing of false ceiling in step (s) comprising of 12 mm thick Gypsum board including GI frame work for seamless ceiling made of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 M length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including two coats of plastic emulsion paint complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutter from frame) area n. exc 1.50 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down chowkhat or frames with shutter (without taking off shutter from frame) area exc 1.50 Sqm but n .exc 4.00 sqm each complete all as specified and directed by Engr-in-Charge.

S&F, Powder coated aluminium chowkhats of 100x44x1.5mm section with rebate complete frame complete all as specified and directed by Engr-in-Charge.

S&F 3mm thick aluminium composite panel (ACP Sheet) including necessary clips, rubber packing & aluminium beading (aluminium frame ) complete all as specified and directed by Engr-in-Charge.

Supply fabricating and fixing aluminium sliding door powder coated of extrusion aluminium section, vertical style of door shutter of size 85mmx44.45mmx1.8mm thick. Top, middle and bottom rail of size 85mmx44.45x1.8mm thick and fixing 4.8 mm thick plain/tinted sheet glass or 3MM thick aluminium composite panel with aluminium beading and rubber gasket/beading as directed including provision of one mortice lock for aluminium door (each) and two aluminium tower bolts of 200mm size for each door fixed with rawl plug including making good of floor/wall to match the existing surfaces complete all as specified and directed by Engr-in-Charge.(Sheet glass Plain/frosted/particle board/ACP sheet shall be measured and paid seperately )

S&F aluminium powder coated glazed three track sliding window of frame 100 x 44 x 1.5mm and sliding shutter of section 40mm x 19mm including 3mm thick sheet glass, ordinary quality exceeding 0.5 Sqm in each pane, in two track shutter and in one track stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, all fittings such as aluminium handle of size 100mm and locking arrangements with each moving leaf complete all as specified and directed by Engr-in-Charge.

S&F aluminium partition wall of aluminium section 100mm x 44mm x 1.5mm thick frame rectangular section and panel of ACP sheet or prelaminated board in bottom panel and 5.5mm thick sheet glass in top panel with rubber lining and aluminium beading around length including necessary fixing arrangement for bottom and top member of aluminium frame in floor/PCC/Brick work as per site requirement with rawl plug etc, including chromium plated steel screws 60cm centre to centre complete all as specified and directed by Engr-in-Charge. (Note : Cost of ACP sheet or prelaminated board and sheet glass shall deemed to be included in the rate quoted for this item )

S&F in repair toughened glass frameless door with fixed portion, of 12 mm thickness, including cutting holes, edges rounded and etching works etc and all kind of SS patch fitting & fixture, spider patch etc, complete all as specified and directed by Engr-in-Charge.

S&F of stainless steel handle 450 mm long fixed to 12 mm thick toughned glass door with and including all fixing accessories i. e. bolt washer, adhesive etc, complete all as specified and directed by Engr-in-Charge.

S&F of SS door lock, glass to glass type, suitable for 12 mm thick frameless toughned glass door with and incl all fixing accessories i. e. bolt, washer, screw, adhesive etc of suitable size, complete all as specified and directed by Engr-in-Charge.

M & L for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engr-in-Charge.

S & F 4.0 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

S & F solid PVC wall panelling consisting of 5mm thick wood grain finish PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed by Engr-in-Charge.

S & F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engr-in-Charge.

S & F solid PVC leeping of 2mm thick wood grain finish PVC sheet is heatbent as lipping on the edges of doors, windows & other edges inclusive of solvent cement and fixing at site complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of old treatment on surfaces of walls through electrically operated grinder using sand paper for preparation of old decorated plastered surfaces of wall and applying two coat of oil emulsion distemper over one coat wall care putty (average thickness of 1.5 mm) complete all as specified and directed by Engr-in-Charge.

Taking up or down tubing GI 15 mm dia incl all fittings complete all as specified and directed by Engr-in-Charge.

S & F of medium grade concealed galvanised steel water tubing with all fittings fixed to wall or laid in floors for 15 mm bore, with and including for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc. complete all as specified and directed by Engr-in-Charge.

S&F of in repair vitreous china wash basin, white colour, flat back type, of size 580 x 450 mm (for hospital use) including waste coupling, wall bracket, waste pipe of suitable size etc, complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), complete all as specified and directed by Engr-in-Charge.

S&F in repair 10 liters PVC valve less syphonic action type flushing cistern, low level white with inlet, ball valve, float and handle including bracket and flush pipe to squatt pattern closet including all joints and making good to the floor complete all as specified and directed by Engr-in-Charge.

S&F in repair of 15mm dia connection 45 cm (PVC), complete all as specified and directed by Engr-in-Charge.

M&L in repair 15mm Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair of 15mm Bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed chromium plated, complete all as specified and directed by Engr-in-Charge.

S&F in repair of wash basin mixer, with out popup waste system, long body, made of cast copper alloy, chromium plated fancy type, suitable for 15 mm bore pipe, complete all as specified and directed by Engr-in-Charge.

S&F in repair Toilet paper holder, vitreous China, box type fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by Engr-in-Charge.

S&F in repair of bottle trap 32 mm size with 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed by Engr-in-Charge.

S&F in repair of two way bib cock suitable for 15 mm bore water pipe, with & including wall flange, made of cast copper alloy, chromium plated fancy type, complete all as specified and directed by Engr-in-Charge.

S&F in repair of handshower (health faucet) with 8 mm dia, 1.0 M long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed by Engr-in-Charge.

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and directed by Engr-in-Charge.

S&F in replacement of PVC made multipurpose cabinet with front door looking mirror of overall minimum size 350 x 450 mm, complete all as specified and directed by Engr-in-Charge.

M & L in repairs for Cast iron floor trap of 75 mm outlet plain with grating including jointing to waste pipe in run lead fixed in cement mortar complete all as specified and directed by Engr-in-Charge.

Dismantling 100/75 mm bore, cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required complete all as specified and directed by Engr-in-Charge.

S&F 100mm bore cast iron soil waste and vent pipe (sand cast pipes) in any length with or without ears with cement joints laid in floors or in trenches complete all as specified and directed by Engr-in-Charge.

S&F cast iron soil waste and vent pipe (sand cast pipes) in any length with or without ears with cement joints laid in floors or in trenches, bore of pipe 75mm complete all as specified and directed by Engr-in-Charge.

S&F for 100mm bore cast iron soil waste and vent pipes (sand cast pipes) in any length fixed with cement joints fixed to walls, complete all as specified and directed by Engr-in-Charge.

S&F for 75mm bore cast iron soil waste and vent pipes (sand cast pipes) in any length with cement joints fixed to walls, complete all as specified and directed by Engr-in-Charge.

S&F for 100mm bore cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) with parallel branches complete all as specified and directed by Engr-in-Charge.

S&F for 75mm bore cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) with parallel branches complete all as specified and directed by Engr-in-Charge.

S & F in repair of 100mm dia stack clamps made out of 50mm wide and 3 mm thick flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, complete all as specified and directed by Engr-in-Charge.

S & F in repair of 75mm dia stack clamps out of 50mm wide and 3 mm thick flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, complete all as specified and directed by Engr-in-Charge.

S & F in repair stainless steel curtain rod 25mm dia of including brackets, side knobs fixed to wall complete all as specified and directed by Engr-in-Charge.

S & F Solar control film 25micron reflective type sticked to glass panes as per instruction of manufacturers complete all as specified and directed by Engr-in-Charge.

M&L MS framed work for door frame (chowkhats) of angle or other section etc Fe 410-W complete for fixing of door shutters complete all as specified and directed by Engr-in-Charge.( Note:- Door shutter shall be measured and paid for seperately)

S & F Steel door MS sheet 0.80 mm thick fixed on MS angle 40x40x6 mm including projecting type hinges, steel handle, complete,with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-Charge.

Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed by the Engr-in-Charge.

Demolition of un-reinforced cement concrete in ground floors and pavings in any position thickness. (Below or above ground level) and removing rubbish off premisses n exc 500 m complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in sunken floor complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for 15 mm thick rendering of ready mix mortar having ratio equivalent to CM 1:4 on brick work or concrete surfaces of wall and finished even and smooth without using extra cement mixed as a whole or in patch work complete all as specified and directed by Engr-in-Charge. Note: White cement shall be used as per site requirement as directed by Engr- in- charge. 2. rendering upto four storey building height complete all as specified and water proofing compound shall be measured and paid separately.

M&L for 15 mm thick rendering of ready mix mortar having ratio equivalent to CM 1:6 on brick work or concrete surfaces of wall and finished the surfaces even and smooth as a whole or in patch work complete all as specified and directed by Engr-in-Charge. Note: White cement shall be used as per site requirement as directed by Engr- in- charge.

M&L for 5 mm thick rendering of ready mix mortar having ratio equivalent to CM 1:3 on concrete surfaces as on ceiling, soffit of stair case, chhajjas facia etc including cement slurry etc finished the surfaces even and smooth as a whole or in patch work complete all as specified and directed by Engr-in-Charge.

M&L for prepartion new decorated external surface of wall and applying two coats of 100% Anti fungal acrylic emulsion exterior grade weather proof paint over a coat of weather resistant acrylic primer complete all as specified and directed by Engr-in-Charge.

Preparing new plaster surface by washing rubbing down and stopping of distempered and painted surface and applying two coats of distemper oil emulsion on surface of walls surface complete all as specified and directed by Engr-in-Charge.

Preparing new plaster surfaces of ceilings by brooming down or by steel wire brushing and applying two coat oil emulsion distemper on ceiling complete all as specified and directed by Engr-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B0 (Using 12.5mm graded stone aggregate) as in flooring smooth surface finished complete all as specified and directed by Engr-in-Charge.

S&F PVC 18/19mm thick PVC moulded solid board ,one side prelaminated for cabinets boxes shutters,etc with shelf and shutters full size fitted under/above kitchen cooking platform and other platform complete all as specified and directed by Engr-in-Charge.

S&F soft closing clip on hinge, full / half overlay type, of stainless steel, complete all as specified and directed by Engr-in-Charge.

S&F multipurpose lock 50mm size with triple keys, suitable for cup board door/drawer , complete all as specified and directed by Engr-in-Charge.

S&F of cup board / drawer knob of stainless steel with matt finish fixed with screw, complete all as specified and directed by Engr-in-Charge.

S&F telescopic type ball bearing slide & runner, suitable for drawers, complete all as specified and directed by Engr-in-Charge.

Demolition of brick work built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed by Engr-in-Charge.

M & L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for aluminium anodised Deco grill 7.5 mm size DG-102, fixed to E/H frames, 1.5mm th, bar size 6.2mm and 7.5mm thick in required sizes complete all as specified and directed by Engr-in-Charge.

S&F in repairs of roller blinds vertical type made out of fabric cloth of approved shade fixed as per the instructions of manufacturers, complete all as specified and directed by Engr-in-Charge.

Removal of demolished material or soil to a distance n.exc 500M and depositing where directed at a level n.exc. 1.5 M above the starting point complete all as specified and directed by Engr-in-Charge.

Taking down old unserviceable point wiring with and including existing conduit / batten type (light, fan, socket or power point) complete such as tube light any type switches, ceiling rose, pendent holder, regulator and socket etc and removing the material from site with chasing and cutting surface of wall / floor/ ceiling etc complete all as specified and directed by Engr-in-Charge. Note: Taking down of LED lights be done carefully and kept in safe custody fo re-use.

Taking down existing sub main wiring aluminium/copper 4/6/10 sqmm complete all as specified and directed by Engr-in-Charge.

M&L for point wiring concealed type with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable connected to common earth and earth dolly with suitable copper lugs drawing into and including rigid non-metallic PVC surface conduit of 20mm dia or higher, medium grade complete with all PVC conduit accessories, GI metal flush box of 1.60 mm thick suitable for modular/conventional switches/sockets/fan regulators with cover plates, blanking plates, brass screws, cup washers etc including all cutting / chases etc in walls and making good to the disturbed surfaces to match the existing complete all as specified and directed by Engr-in-Charge for the followings :- (Note - All accessories likes modular top cover plate/ hylum sheet cover plate, Metal flush box, screws etc as applicable will be included in quoted rates.) For one light point/ceiling fan/exhaust fan point controlled by one switch.

All as per srl Item No. 78 here-in-before but one socket outlet 5 Amps controlled by one switch on same board.

All as per srl Item No. 78 here-in-before one socket outlet 5 amps controlled by one switch on independent board.

All as per srl item No. 78 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 15 Amp power point.

All as per item No.78 above but wiring with 4 sq mm PVC insulated multi-stranded copper conductor for industrial socket outlet 3 pin 16 / 20 Amps point and one single core 2.5 sq mm PVC insulated unsheathed copper cable as earth continuity conductor.

Material and labour in replacement of Sub main wiring with 2 run of 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including cutting and chasing,and also PVC conduit suitable dia as per SSR part-I with medium grade including 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as specified and directed by Engr-in Charge. Note : 1. The two run of 4 Sqmm wire, one run of 4 Sqmm wire and 1 run of PVC conduit will be measured as one unit.

All as per srl item no. 83 here-in-before but with 2 run of 6.0 sq mm FRLS copper wire with 6.0 Sqmm FRLS copper cable as earth wire.

All as per srl item no. 83 here-in-before but with 4 run of 16.0 sq mm FRLS copper wire with 16 Sqmm FRLS copper cable as earth wire.

S&F modular switch 10 Amps, one way, one module 240 volts complete all as specified and directed by Engr-in-Charge.

S&F modular switch 16 A, 1 module,240 volts complete all as specified and directed by Engr-in-Charge.

S&F modular socket, 3 pin 6 Amps,240 volts, 2 module complete all as specified and directed by Engr-in-Charge.

S&F modular socket 6/16 A, 5 pin, 2 module, 240 volts complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of electronic fan regulator, Modular type and making all necessary connections complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps with and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of MCB protected modular AC/Geyser box complete with and including 6 pin socket, plug top, modular cover plate, mini MCB SP 20 Amp capacity and PVC gang box etc, complete all as specified and directed by by Engineer-in charge.

Supply and fixing in repair LED luminaire (2'x2' LED fittings), 36 watt, 220 V AC recessed/surface mounted type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engr-in-Charge.

Refixing of LED light fitting any type complete with all existing accessories complete all as specified and directed by Engr-in-Charge.

Taking down carefully ceiling fan/Exhaust Fan/cabin fan of any size, sealing cable end, dismantling blades & removing fan and blades to store complete all as specified and directed by Engr-in-Charge.

M&L for painting of ceiling fan complete with synthetic enamel paint by spraying including filling cavaties with filter one coat after cleaning complete all as specified and directed by Engr-in-Charge.

Hanging only with fixing accessories ceiling fan and connecting with and including 3 core flexible copper cable from ceiling rose to fan complete all as specified and directed by Engr-in-Charge.

Fixing only exhaust fan/cabin fan and connecting up including provision of cable from ceiling rose to connector block complete all as specified and directed by Engr-in-Charge.

Supply and fix in repair of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 08 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as specified and directed by Engr-in-Charge.

All as per srl item No. 99 here in before but of 12 Way SPN suitable for incorporation of MCBs and isolator etc complete all as specified and directed by Engr-in-Charge.

All as per srl item No. 99 here in before but of 415 V, 8 Way TPN suitable for incorporation of MCB TPN, MCBs and isolator etc complete all as specified and directed by Engr-in-Charge.

All as per srl item No. 99 here in before but of 415 V, 8 Way VTPN suitable for incorporation of MCCB, MCBs and isolators etc complete all as specified and directed by Engr-in-Charge.

M&L in repair MCB SP 6 to 32 Amp, B Curve type, 10kA, single pole with over load and short circuit protection complete all as specified and directed by Engr-in-Charge.

M&L in repair MCB SP 63 Amp, B Curve type, 10kA, single pole with over load and short circuit protection complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair MCB, SPN type of 40 to 63 amps capacity, 240V, 10 KA with all connections complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair MCB, TPN type of 63 amps capacity, 240V, 10 KA with all connections complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair MCCB 415 Volt, 16kA,4 pole of 125 Amp capacity with all connections complete all as specified and directed by Engr-in-Charge.

Taking down carefully by disconnecting, sealing cable ends of addressable/conventional heat & smoke detector, manual call point, response indicator etc & refixing, connecting with existing wires including testing the same in to their original position to make the system fully functional complete all as specified and directed by Engr-in-Charge.

Supply and fix electric water heater(geyser), storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed by Engr-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair round shape LED down lights15 watt, 220 volts, AC, recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair bed head light fitting including 1x18 Watt FTL/LED, 1x36 watt CFL/LED, 1x5 watt LED lamp made of powder coated CRCA sheet & acrylic cover including 2 metre lenth of pendent with 03 Nos switches for each light complete all as specified and directed by Engr-in-Charge.

M&L for french polish on old wooden surfaces of any description width ae girth including cleaning and preparing the surfaces incl a coat of wood filler but one or more coat complete all as specified and directed by Engineer-in-Charge.

SANJEEV ENTERPRISES

R D ENTERPRISES

V.K. Enterprises

OMVIN ENTERPRISES LLP

M/s SAAR ENGINEERS