SPL REPAIRS TO BLDG NO P 10 1 P 10 2 P 10 3 (OR MD ACCN) (TYPE II QTR) INCLUDING SPECIAL REPAIR TO WATER SUPPLY STORAGE/DISTRIBUTION SYSTEM AT MES INSTALLATION UNDER GE I GOS

Amount

Taking down chowkhats with shutters not exc. 1.5sqm each complete all as specified and as directed.

Taking down chowkhats with shutters exc. 1.5sqm but.not exc. 4 sqm each complete all as specified and as directed

S&F 2nd class Hard wood in plain, solid, straight chowkats and frames wrought framed, rebated on the solid, rounded or chamfered put together with glue pinned joints complete all as specified and directed

S&F Bands, straps, clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate for fixing of hold fast and making good disturbed surfaces complete all as specified and directed

S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides to match complete all as specified and directed

S&F 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing shown in section 8 of SSR part -II complete all as specified and directed

S&F 100mm size butt hinges medium weight (ISI Marked), rolled mild steel complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

S&F 150mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F Aluminium alloy, anodized, sliding door bolt (ISI Marked) of 300mm with hasp & staple (Bolt type) and fixing clips of sheets, coat or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required cessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each complete all as specified and directed.

M&L two coat of synthetic enamel paint over one coat of pink primer including preparation of steel/wooden surface of any description complete all as specified and directed.

M&L for veneered decorative plywood 19 mm thick, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with screws to timber fame work as in cup board shutters etc complete all as specified and directed.

S&F 40mm dia cub board knob brass polished fixed with nut screw and washer of mild steel bright finished complete all as specified and directed.

S&F ball catches with 8 mm dia steel ball and brass body and striking palte incl latting in and fixed complete all as specified and directed.

S&F continuous (Piano type) hinges 40 mm mild steel bright finish electro galvanised complete all as specified and directed.

S& F hasp and stapple safety type of aluminium anodised 75 mm long complete all as specified and directed.

Taking down existing water proofing membrane and cleaning roof, 15mm thick plastered surface etc preparing the surface to receive plaster by brushing with wire brush and fanning the surface to remove all loose dirt etc and brushing neat cement slurry @ 3.00 Kg/Sqm including 15 mm thick plastered in cement morter 1:4 with liquid water proofing comound complete all as specified and directed.

M&L for water proofing treatment for roof slabs by applying bitumen primer @ 0.3 ltr/sqm then applying hot blown bitumen 85/25 @ 1.20kg/sqm and laying 3 mm thickwater proofing membrance modified with glass mat reinforcement weight 50 gram/sqm not less than 3 kg /sqm with overlap of 100 mm and end lap 150 mm and finally applying aluminium based pain on top complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item No 26 above but on skirting/dado incl 10mm thick rendering of backing layer in CM 1:4 complete all as specified and directed.

M&L coloured glazed ceremic tiles 300x200x7 mm in dado set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles incl 10mm thick rendering of backing layer in CM 1:4 complete all as specified and directed.

M&L 20 mm thick Makrana Colour/white Marble machine cut on kitchen platform, over cement screed base laid and joined with gray cement slurry mixed with pigment to match the shade including edge cutting , nosging , rubbing and polishing incl 20 mm thick screed bed in CM 1:4 complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, pillars, arches etc complete all as specified and directed.

M&L brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface of wall and finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface of ceiling/chajjas etc and finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick rendering in cement and sand mortar 1:3 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound.

M&L for preparation of new plastered surface and applying two coats of oil bound distemper over 3 mm thick wall care putty complete all as specified and directed.

M&L complete removal of existing treatment on walls and applying two coats of oil bound distemper over 3 mm thick wall care putty to walls complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of oil bound distemper over 3 mm thick wall care putty to ceiling complete all as specified and directed.

M&L complete removal of existing treatment on ceiling and applying two coats of oil bound distemper over 3 mm thick wall care putty to ceiling complete all as specified and directed.

M&L for preparation of newly plastered or unplasetered surfaces and applying finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)® walls complete all as specified and directed.

M&L complete removal of existing treatment on wall including removal of vegetation and applying finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)® walls complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description not exc 10 cm width or girth and priming with red oxide zinc chrome and painting with two coats of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and pavings n. exc 15 cm thick (above or below ground level) complete all as specified and directed.

M & L 75 mm thick PCC 1:3:6 type C-2 as in sub base, Paving, plinth protection, finished even and fair complete all as specified and directed.

M&L for 20mm thick screed bed in cement mortar(1:6) as in bedding of chequered tiles complete all as specified and directed.

M&L for chequered cement concrete tiles 20cmx20cmx25mm thick set, jointed and painted with grey cement and pigment in neat cement slurry in floors complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8, type D-2 using (40mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc 0.5 Cum getting out, any to types of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and directed.

M&L PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate as in foundations filling and mass concrete complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws incl ridge complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

S&F steel work in tubular poles & trusses (framed) including purlins,rafters and special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1979 grade St-240 complete all as specified and directed.

S&F Framed work such as grill grating, doors or gates with ends of bars shouldered and / or rivetted, or forged into spikes, framed gurad bars, barred iron doors, ladders, framed balusters, walk ways railings and similar work confirming to Fe 290 Gde E-165 of any section and sizes complete all as specified and directed.

Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames, aluminium frame glazed with putty or fixed with beads in repairs complete all as specified and directed.

S&F glass pan ordinary quality 3mm thick and glazing with oil putty/ wooden beads in square n. exc 0.5 m each pane complete all as specified and directed.

S&F in repair vitreous china wash basin, white flat back size580mmx450mm, excludings taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with integrall footrest (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair PVC low level flushing cistern (white) 10 Ltrs capacity with internal fitting, push button operated type with and including bracket, PVC flush pipe etc complete all as specified and directed.

S&F in repairs.Sink with draining board made out of stainless steel 1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410 mm x 330mm x 160mm complete all as specified and directed.

S&F 1 mm thick stainless steel plate rack of size 900x600x200mm including fixing with rawal plug and screws complete all as specified and directed Make Blue Star cat No kpr - 313/ kpr- 314 or equivalent of nirali/ parryware complete all as specified and directed.

S&F in repair Tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls complete all as specified and directed.

S & F in repair Chromium plated shower roses with or without swivel joints, of size 125 mm, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair angle valve 15mm bore brass chromium plated with capstan head screwed for iron pipe complete all as specified and directed.

S & F in repairs grating doom 125mm dia with waste hole of PTMT fixed on floor/nahani trap with cement mortar, (Minimum weight 40 gms) complete all as specified and directed.

S & F in repairs PVC waste pipe 32mm dia, 60 cm long for WHB with cup, complete all as specified and directed.

All as per Item No 67 above but 40mm dia for sink complete complete all as specified and directed.

S & F in repairs Stainless steel waste coupling for S.S Sink 75mm to 100mm dia set with rubber washer plug etc complete all as specified and directed.

S&F in repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts complete all as specified and directed.

Taking up or down steel water tubing and connections of following descriptions :- (a) 15 mm bore

(b) 20 mm bore

Supply and laying CPVC pipes SDR 11 & Plain CPVC 11 fitting on walls/ceiling or laying in floor complete all as specified and directed of following descriptions :- (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Brass Elbow (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Brass Elbow (3/4 x1/2) 20 mm outer dia

S&F CPVC Brass Tee (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Male Brass Threaded Adaptor (MTA/MBTA) (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Female Brass Threaded Adaptor (FTA/FBTA) (a) 16 mm outer dia

(b) 20 mm outer dia

S&F CPVC Tank adaptor 20 mm outer dia

S&F CPVC Union (a) 16 mm outer dia

(b) 20 mm outer dia

S&F in repair ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms), complete all as specified and directed.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm bore complete all as specified and directed.

S&F in repair 15 mm fancy type pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts complete all as specified and directed.

S&F in repair 15 mm fancy type stop valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed.

S&F in repair 15mm bore bib tap cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube complete all as specified and directed.

S&F in repair sheet glass shelf assembly consinsting of 5.5 mm thick sheet glass shelf 12 CM wide with CP bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repair 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F in repair 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&Fin repair PVC (SWR) vent cowl of 110 mm dia complete all as specified and directed.

Supply only 32mm dia flush pipe of polythelene of low or high density, for low or high level flushing cistern complete all as specified and directed.

S&F in repair CI 'P' or 'S' trap of 100mm size complete all as specified and directed.

Dismantling PVC water tanks exc 1000 ltr but n. exc 2000 ltr capacity and removing to store complete all as specified and directed.

S&F 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 25/32 mm dia decorative/drapery curtain rod with bub & Bracket & internal tunnels complete all as specified and directed.

S&F in repair 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair soap dish,chromium plated, 100X100X60mm, fixed to wall with plugs with chromium plated screws complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan/exhaust fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders, brackets, bulk head fittings etc removing material to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and also making good disturbed surfaces of wall, floors etc complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheating FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly by providing lugs including sunk in pressed steel terminal boxes of 1.6 mm thick concealed in wall (duly painted with two coats of black bituminous paint over a coat of red oxide primer in and out sides) with and including cutting holes for switches, sockets, regulators etc as per requirement including fixing with machine screw, washer etc complete all as specified and directed. Make of wire : Finolex/Plaza/Polycab/Havells. (a) One light/bell point controlled by one, one way switch

(b) One fan/exhaust fan point controlled by one, one way switch

(c) One 5 Amp socket point controlled by one way switch on independent board.

All as per item No 107 above, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and directed.

M&L for socket outlet 2 in 1, 3 pin, 5A flush type complete all as specified and directed. Make : Indo Asian/Plaza/Havells.

M&L for socket outlet 2 in 1, 3 pin, 5 Amp and 15 Amp flush type complete all as specified and directed. Make : Indo Asian/Plaza/Havells

M&L for Switch piano flush type single pole one way 15 Amp complete all as specified and directed. Make : Indo Asian/Plaza/Havells.

M&L for Switch piano flush button 5 Amps complete all as specified and directed. Make : Indo Asian/Plaza/Havells.

M&L for ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all as specified and directed.

S&F for sub main wiring two single core PVC insulated and unsheathed cable with 4 Sqmm multi -strand copper conductor drawing in PVC casing caping with 2.5 Sqmm PVC copper conductor cable as in earth wire system ,including taking out old wiring complete all as specified and directed. Make : Finolex/Plaza/Polycab/Havells.

S&F Sheet metal enclosure for DB’s suitable for MCBs of single pole and neutral 8 way (Double door) with 200 amp rated bus bar complete all as specified and directed. Make : Indo Asian/Legrand/Havells.

S&F Isolator DP 32A, 240 volts complete all as specified and directed. Make : Indo Asian/Legrand/Havells.

S&F MCB SP up to 32 Amp, 240 voltcomplete all as specified and directed. Make : Indo Asian/Legrand/Havells.

S&F Ceiling Fan regulator electronic step type complete all as specified and directed. Make : Havells/CG/USHA/Bajaj.

M&L for PVC rectangular block of size 25 cmx20cmx5cm depth, closed recessed 3mm thick plastic laminated sheet complete all as specified and directed.

S&F energy efficient LED integrated batten suitable for indoor applications tube light fitting 1x20 Watt 4 FT complete all as specified and directed. Trim LED NEO all as per Surya Cat Part No SLE BT 20 IL equivalent in Philips/Wipro.

S&F LED Bulk Head fitting complete all as specified and as directed. Make : Surya Part No SLE BLH10W PLUS or equivalent in Wipro/Philips.

S&F Decorative, wall mounting, champagne gold finish fixture with plastic body with 12W retrofit CFLsuitable for lamp all as per Surya Cat Part No SLE WL12W-GP200 or equivalent in Wipro/Philips.

S&F LED Lamp pin type 9 watt all as per C&S Cat Part No LTHPLEDLAMP9W22 BULB or equivalent in Surya/Wipro.

S&F for ceiling Fan 1200 mm sweep with blade, down rod complete all as specified and directed. Make : Havells/Bajaj/Surya.

S&F exhaust fan 300 mm sweep, 1400 RPM with louver complete all as specified and directed. Make : Havells/Bajaj/CG.

Supply and laying for 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire one twin core cable flat or circular single stranded conductor size 10 Sqmm , including taking down old cable complete all as specified and directed. Make : Polycab/Plaza/Finolex.

Supply and fix in replacement Security light fitting LED type of 36 watt High performance IP-66, energy saving and environmential friendly long life LED with GI tubing 25/40 mm dia medium grade suitable for street light , mounting bracket with its clamps including two coats of synthetic enamel paint over a coat of red oxide primer and other accessories and connecting with twin core flexible wire all as per Surya Cat Part No SLE UL 36WIP66 (LXN) or equivalent in Philips/Wipro.

M&L earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 Metres below normal ground level, connecting to the Galvanised iron earth lead wire 4mm dia, by means of bolts, nuts, check nuts and washers of galvanised iron and 4mm earth lead protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of 75x50x6mm phosphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 3 of SSR-2009 Part-I and connecting to earth test point including testing on completion complete all as specified and directed.

Supply and replacent of GI pipe light grade with all fittings laid in trenches/walls of size 20 mm dia complete all as specified and directed.

Supply and replacement of Gun Metal, globe or gate valves, 20 mm with iron wheel head, screwed both ends for iron pipe and fixed with pipes as suitable complete all as specified and directed.

Dismantling posts or struts (wood,steel or RCC) any section,Including taking out embedded portion concrete brick, ground massonary,etc and making good disturbed ground complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground ground level) and removing demolished material to a distance exceeding 50 metres but not exceeding 100 meters where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

Excavating in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundations etc and getting out in soft/loose soil complete all as specified and directed.

M&L for hard core of gauge exc 63 mm but n exc. 100 mm deposited spread and levelled in layers n.exc 15 cm thick watered and rolled/rammed to a true surface with broken stone or boulders complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling & mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded aggregate as in walls or retaining walls, any thickness, size or shape including plasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

M&L for precast cement concrete, PCC 1:3:6 type C-1 blocks masonry with solid blocks exc 10 cm in width and set in CM 1:6 complete all as specified and directed.

M&L form work to flat sides of concrete foundations, footings, sides and soffits of foundation and plinth beams, columns and similar work vertical or batter rough finished surface of concrete of that surfaces complete all as specified and directed.

M&L cement concrete 1:3:6 type C-1 using 20 mm graded aggregate as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply only chain link MS galvanised fencing any size or type n.exc 4 kg/sqm complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and 'scraved the other to be fitted with washers and one hexagonal or square nut n.exc 5 cm long and dia 5 to 10 mm complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over cut to length bent to shape required, hooking, bending and binding with ms wire (annealed) not less than 0.90 mm dia complete all as specified and directed.

M&L preparation of plastered or unplastered new surcafe of wall and applying three coats of white wash to walls complete all as specified and directed.

M&L painting to steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamel paint over a coat of Red oxide or Zinc chrome incl preparation of surfaces complete all as specified and directed.

M&L painting to steel surfaces of any description n.exc. 10 cm in width or girth with two coats of synthetic enamel paint over a coat of Red oxide or Zinc chrome incl preparation of surfaces complete all as specified and directed.

S & F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. (each line wire to be measured).

S&F in repairs Concertina coils super barbed bladed profile of dia 600 mm of and wt of coil for 50 spiral turns shall not be less than 9.0 kg and one coil (50 spiral) shall not be stretched to more than 6.0 mt. blade shall be 0.50mm th galvanised steel strip and 2.5mm dia core wire fixed to angle iron brackets or masonry surfaces with necessary accessories like straining wires, fixing clips etc complete all as specified and directed.

Returning filling in incl, spreading, levelling watering and well ramming in layers n.exc 25 cm soft/loose soil complete all as specified and directed.

Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

S&F GI wire netting 0.90mm dia and12mm mesh lathing to wood or metal studding ,joists,etc.in walls, ceilings, stanchions, beams,etc.Including all laps,cutting and waste complete all as specified and directed.

M&L cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in leveling concerte in floor of SWT,laid to slope for further treatment with using Integral water proofing compound .(WPC shall be measured separtly)

M&L for 15mm thick wearproof topping as specified in CM 1:3 mixed with metalic floor hardener @5% of weight of cement,laid on conceret floors and pavings and finished even and smooth (except metalic hardener) complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concerte surfaces mixed with integral water proofing compound finished even & smooth without using extra cement complete all as specified and directed. Note: WPC shall be measured and paid separtly.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extracement complete all as specified and directed.

Supply only metalic floor hardner.

Supply only Liquid water proofing compound

M&L for PCC (1:2:4 type B-0 using 12.5mm graded stone aggregate)as in copings,cills,stepsseismic and other similar bends,plinth courses,string corses,lacing courses ,parapets and railings upto 60cm in height,apex stonews,water throughs and the like including weathering.sightly rounded or chamfered an gles and throating, complete all as specified and directed.

M&L for preparation of new plastered sufaces of walls including cornices,pilasters and applying three coat of white wash complete all as specified and directed.

Taking down old unsv LT panel and supply, install and commissioning of LT panel board outdoor type, factory fabricated prewired, CPRI aproved, cubical type of appropriate size in door, dust and vermin proof, made out of 50x50x6mm angle iron frame/legs and 3,15 mm thick CRCA sheet with openable shutters on both sides (front & rear), and painting to all steel surfaces internally and externally with two coats of powder coated paint over a coat of red oxide zinc chrome primer suitable for 440 volts, 3 phase 4 wire system enclosed with copper bus bar of 400 amp for R,Y,B phases and 400 amps for neutral, having locking arangement mounted on four legs 90cm high (30 cm below ground level and 60 cm above ground level), embedded in PCC (1:2:4 ) type B2 block each of size 200x200x300mm complete all as specified & directed by the Engr-in-Charge to accommodate the following accessories and the panel should have arrangement sufficient space to work easily :- Incomming:- (a) Copper bus bar 400 A for three phase and neutral duly insulated with sleeves of different colour RYB. (b) MCCB 4 Pole 200A 35 KA - 1 Nos (Make : C&S Cat No CSE2N250ATM4P-* or equivalent in L&T/HPL. (c) Digital multi functional Panel meter showing V/I.Fq, PF along with CTs , Make:-C&S/Schneider/Indoasian/ - 01 Set (d) Indicators lamp LED type RYB 240 volts - 01 Set. Outgoing :- (e) MCCB 4 Pole 100A 25 KA - 1 Nos (Make : C&S Cat No CSE1M125FMU4P-* or equivalent in L&T/HPL). (f) MCCB 4 Pole 63A 25 KA - 1 Nos (Make : C&S Cat No CSE1M125ATM4P-* or equivalent in L&T/Indoasian). (g) MCB 2 Pole 40 Amp 25KA - 2 Nos (Make : C&S Cat No CSMBS1C32N or equivalent in L&T/Indoasian). (Note : (i) Incoming and outgoing cable shall be fixed with appropriate size of copper thimble. (ii) Apron shall be provided at bottom for protection of cable to avoid entry of vermins, reptiles. (iii) Entries of all sizes of cables in panel should be done through adequate size of metallic cable glands.

M& L for MS/CI/DI fittings up to 150mm bore such as collar, bends (any type radius, any angle, double end socketted or double flanged or spigot & socket, tail pieces (all socketed or all flanged with an equal & other end tapering bellmouth or flanged plates, connecting pieces straight (both end flanged or socketed of socket & flanged & spigot ends or bellmouth tailpieces ( one end flanged & other end spigot or socket or tatering as bell mouth or flanged ) caps blank flanges heavy duty suitable for mechanical joint/flanged joint with and incl taking down old fitting of any type and any size complete all as specified and directed. Note: Certifiacte for Weight of fitting by the manufacturere shall be submitted before payment.

Taking up or down cast iron water mains of 80mm bore(including all fittings), with spigot and socket ends and lead joints including burning out joints including turning water OFF or ON as necessary and taking off and refixing covers, access doors etc. complete all as specified and directed.

Supply and laying in trenches /Wall upto height 12mtr and flanged ends, centrifugally cast (spun) iron pipes class 'A"80mm bore including rubber gasket ring, conforming to IS : 1536-2001 and ISI marked, complete all as specified and directed. (Excavation and earth work, joints and jointing material and CI specials will be measured and paid seperately)

Supply and fixing and testing CI sluice valves 80mm bore both ends flanged and drill in with brass spindle and brass check nuts, hand wheel made out of CI complete suitable for tested hydrostatic pressure 15 Kg/Sqcm. (PN 1.6) and confirming to IS 780 complete and of size 150mm dia Make: Kirloskar/Zoloto/BIR

All as per Item 167 above but of size 100mm dia

M & L for replacement of valve Chamber Cover with angle iron framed works by welding angle iron of size 40x40x6mm and 3mm MS Sheets of Fe-410 W (Gde-E-250) qualtiy - B, with handle and hinged at one side complete all as specified and as directed including applying two coast of synthetic enamel paint over a coat of red oxide primer.

HARAGOURI SUPPLIERS

M/S JAGANNATH SASMAL

M/s MAA BHAIRABI ENTERPRISES

M/S SIWALIK AND CO

G.KRISHNA MURTHY AND PARTNERS

DHABALESWAR ENGINEERING WORKS