Construction of Raj Niwas at Kavaratti, Lakshadweep. SH- Architectural Works, Interior Works and Exterior Development Works (Re e-Tender-III)

Amount

EXPERT FLOORING

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 300 mm Finished Floor Height (FFH)

Supply of machine tuffed polypropylene Textured Carpet with Rubberised Cushion backing as per details given below. The carpet shall have minimum production yarn weight equivalent in range of Oz per square yard as mentioned below. The carpet shall have sufficient gauge with sufficient stitches 1/10 per inch. The carpet shall be made of 100% solution dyed fibre content. The carpet should carry a warranty not less than 15 years from the manufacturer and supplier of carpets. The carpet shall have the pile height ranging from 2.5 mm + / - 0.5mm and total thickness of the carpet tile shall also range from 6mm + / - 0.5mm. The carpet shall have anti-static properties as per the manufacturers specifications and as approved by the Architects. The Carpet shall also be Stain and Soil resistant as per the manufacturers specifications. Shampooing of carpet to be done before site is handed over. This also includes covering of carpet with plastic cover and taping of joints with masking tape.

Providing and laying 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Bullberry Grey marble for vanity counters/ wash basin counters, facias and similar locations of required size, approved shade, colour and texture laid over 8 mm thick multiwood board, with cement based high polymer modified quick set adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete, all complete as specified and as directed by the Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete as per approved drawings and directed by Engineer-In-Charge

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required as per approved drawings and as directed by Engineer-In-Charge. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

CEILING

Providing and fixing Gypsum false ceiling with 2 layer (12.5+12.5mm) for grooves at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks) As per design approved by Architects.

Providing and fixing Gysum false ceiling (12.5 mm) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks)

Providing and fixing Gysum false ceiling (12.5 mm) with Gold foil finish in cuved/dome shape at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification including one or more coats of synthetic enamel paint and fixing golden foil leaves over one coat of PU polish and final finishinh with PU polish and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed and the cost of double height scaffolding all complete as per drawings, specification and direction of the Engineer in Charge : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks) As per design approved by Architects.

Providing & fixing 8 mm thick Calcium Silicate false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and fixing wooden trap doors for access to the areas above false ceiling. The trap door shall have an external frame made of 2" x 2" Teakwood scantling on which the shutter is hinged. Shutter shall be made 12mm thick solid core flush shutter with timber edge lipping as per the detail drawings. Concealed hinges shall be used to mount the shutters and locking shall be provided with panel locks. The shutter shall be molded in level with the false ceiling forming a groove all around. Sufficient number of hinges and locks shall be provided to avoid sagging of the shutter. Key also shall be supplied. No extra rate shall be provided for suspenders or frame works all-round for linking the trap door to false ceiling, as per design approved by architects.

Supply & Installation of veneer finsihed (teak finish) false ceiling made up of 12 mm thick BWP 710 fire retardant plywood conforming to IS: 5509/ 10701 grade with necessary frame work as required for holding 12 mm thick fire retardant plywood conforming to IS: 5509/ 10701 grade with veneer 4 mm thick A-grade finish etc complete. The frame work shall be supported by necessary GI supports as per requirments etc. complete as per design approved by architects.The exposed surface shall be polished to provide smooth finish with PU polish material of approved brand

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level,suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing & Installation of Decorative veneer finsihed wooden ceiling with 19 mm BWP 710 fire retardant plywood conforming to IS: 5509/ 10701 grade frame with base 12 mm BWP 710 fire retardant plywood conforming to IS: 5509/ 10701 grade with veneer 4 mm thick A-grade finish also with teak wood scantling with craving detail as per drawing,complete as per design approved by architects.The exposed surface shall be polished to provide smooth finish with PU polish material of approved brand

Providing and fixing teak wood beading of size 50mmx 20mm fixed with wooden adhesive of approved quality and screws/ nails or suitable adhesive on the edges of the ceiling as per design approved by architects.The exposed surface shall be polished to provide smooth finish with PU polish material of approved brand

Providing carved teak decorative blocks of size 300mmx250mmx100mm and fixing in ceiling along ceiling rafters in position with necessary stainless steel screws or required adhesives etc, as per design approved by architects.The exposed surface shall be polished to provide smooth finish with PU polish material of approved brand

Supply & Installation of veneer finsihed (teak finish) architrave with gold foil finish made up of 12 mm thick BWP 710 fire retardant plywood conforming to IS: 5509/ 10701 grade with necessary frame work in 19 mm thick BWP 710 fire retardant plywood conforming to IS: 5509/ 10701 grade as required for holding 12 mm thick plywood,applying one or more coat of wood primer,fixing gold foil leaves of approved brand over one coat of enamel paint and one coat of PU polish,a final coat of PU polish etc complete. The exposed surface shall be polished to provide smooth finish with PU polish material of approved brand.The frame work shall be supported by necessary GI supports as per requirments etc. complete as per design approved by architects.

Supply & Installation of veneer finsihed (teak finish) architrave made up of 12 mm thick BWP 710 fire retardant plywood conforming to IS: 5509/ 10701 grade with necessary frame work in 19 mm thick BWP 710 fire retardant plywood conforming to IS: 5509/ 10701 grade as required for holding 12 mm thick plywood. The exposed surface shall be polished in required number of coats to provide smooth finish with PU polish material of approved brand.The frame work shall be supported by necessary GI supports as per requirments etc. complete as per design approved by architects.

Providing and fixing of decorative (CNC cut) ceiling, made in Grade-I MDF Board 12 mm thick confirming to IS:14587, finished with golden mettalic paint and are fixed using necessary screw, etc complete, as per design approved by architects.

Supply and installation Acoustic ceiling of 15 mm thick Glass Fibre tile of size: 600x1200mm with density 110 kg/m3, with Green (VoC, RC%)-Recyclable having NRC value upto 0.9 and 17 mm thick Wood fibre of size: 600x1200 mm with density 750-1150 kg/m3, with Green(VoC,RC%)-Low class1,having NRC value upto 0.85. Fixed with T-grid with accessories. The rates for above works are inclusive of all cost materials and fabrics, fabrication charges, transportation and installation, labour, etc complete, as per design approved by Architects.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as directed by Engineer-In-Charge

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface as directed by Engineer-In-Charge. Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade as directed by Engineer-In-Charge:Two or more coats on new work

WALL PANELLING

Providing and fixing of wall panelling with 19 mm thick 710 BWP fire retardant plywood conforming to IS: 5509 /10701 grade internal frame work over which 12 mm thick 710 BWP fire retardant plywood is fixed on. Exposed area finishing with 12.5mm thick gypsum board with ash wooden skirting, as per design approved by Architects.

Providing and fixing of wallpaper with paper backing with 220-250 GSM. The wallpapers are printed on either low VOC, or PVC-free LEED-certified substrates- either of which are intended for a range of commericial applications. These are fixed with Bartoline or any brand approved by Architect/Engineer-In-Charge all purpose wallpaper adhesive of high quality and which is easy to mix. As per design approved by Architects.

Providing and finishing of walls by artist hand painted with acrylic paint of required finish, as per design approved by Architects.

Providing and fixing of wall panelling with 19 mm thick BWP 710 fire retardant plywood conforming to IS: 5509 /10701 grade internal frame work and 12 mm thick fire retardant plywood conforming to IS: 5509 /10701 grade . Exposed area finishing with 12 mm thk. BWP 710 fire retardant plywood conforming to IS: 5509 /10701 grade with veneer-A grade finish and one coat of PU coat and flexiply with veneer covering combination, with SS Gold finish profile 20mm, with all necessary fittings and labour charges, as per design approved by Architects.

Providing and fixing of artificial grass on 12 mm thick BWP 710 fire retardant plywood conforming to IS: 5509 /10701 grade backing ,fixed with necessary fittings. As per design approved by Architects.

Providing and installation of Acoustic wall panelling with 12mm pet panels of size: 1220x2440 of weight 1800 g/m2, which are 50 % recyclable material has LEED MR-4, having NRC value upto 0.8 and 15 mm Wood Fiber of size: 600x1200mm of density 410 kg/m3, with Green (VoC,RC%)-Low 10, having NRC value upto 0.9,with polyester fibre infill of 500GSM. Fixed with GI struts of Web Width 48mm, depth 48mm, 0.6mm thickness are used to form frame from ceiling to floor of CC – 600mm framing on both the planar sides from (Vertical & Horizontal). Above this framing, one side first layer will be gypsum board of 12mm thick and second layer will be 15 mm wood wool board and another side will two layer of 12 mm thick gypsum board of approved make. Wood wool boards, pet panels and gypsum boards are installed using black phosphate or nickel pated bugle head fine threaded screws horizontally or vertically as per the architecture design and infill is used to fill the gap between the frames. The rates for above works are inclusive of all cost materials incluidng fabric, fabrication charges, transportation and installation, labour, etc complete, as per design approved by Architects.

Providing and fixing 80 cm decorative mirror with backlighting and wooden edge moulding as per approved design and direction of Architect/Engineer-In-Charge

Providing and fixing of miror panelling of back panel with 12 mm thick 710 BWP fire retardant plywood panelling over 19 mm thick 710 BWP fire retardant plywood/ hardwood frame woth wooden architrave. Front face with 5 mm thick silver backed mirror with pencil edge finish, solid oak wood strips in all exposed area with approved finish/ shade.With LED back lighting. As per design approved by architects.

Supplying and fixing make wall to wall shower enclosure with one fixed glass 1- part. Glass partitions using 8mm thick Toughened glass with necessary hardware fittings in Chrome finish with 1 Top Channel, 1 Wall Profile, 2 Magnet Profile, , 1 Damn strip on the bottom, 1 fixed panel glass as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware. As per design approved by architects.

Supplying and fixing one sliding door using 8mm thick Toughened glass with necessary hardware fittings in Chrome finish with 1 Top Channel, 1 Magnet Profile, 1 Door knob, 1 Damn strip on the bottom, 1 guider for smooth sliding passage, Rollers : ball bearing encapsulated in brass should be concealed in the top channel, 1 Sliding Glass as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware. As per design approved by architects.

Supplying and fixing make wall to wall shower enclosure with one fixed glass and one sliding door 2- part. Glass partitions using 8mm thick Toughened glass with necessary hardware fittings in Chrome finish with 1 Top Channel, 1 Wall Profile, 1 Magnet Profile, 1 Door knob, 1 Damn strip on the bottom, 1 guider for smooth sliding passage, Rollers : ball bearing encapsulated in brass should be concealed in the top channel, 1 Sliding Glass & 1 fixed panel glass as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware. As per design approved by architects.

Supplying and fixing make wall to wall shower enclosure with two fixed glasses and one sliding door 3- part. Glass partitions using 8mm thick Toughened glass with necessary hardware fittings in Chrome finish with 1 Top Channel, 2 Wall Profiles, 1 Magnet Profile, 1 Door knob, 1 Damn strip on the bottom, 1 guider for smooth sliding passage, Rollers : ball bearing encapsulated in brass should be concealed in the top channel, 1 Sliding Glass & 2 fixed panel glasses as per the approved drawings & samples. Anti Limescale coating on the glass to prevent any lime deposits on the glass is a must for easy maintenance, should have 5 years warranty on all hardware. As per design approved by architects.

HANDRAILS

Providing teak wood top rail of size 50mmx35mm , fixed with necessary fittings and screws etc including PU polishing, as per design approved by architects.

Providing and fixing 12 mm thick toughened glass for railing, fixed on wood frame, as per design approved by architects.

SOFT FURNISHING

BEDDING

Supplying and fixing of Mattress (10")- breathable bonded foam core with HR foam layer on either sides, both sides usable- medium firm upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying and fixing of Mattress Protector - King (Size:78"x72"), of 100% Water Proof Terry Top , with Fitted Sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Bed sheet - King (Size: 112"x116"), of 100% Cotton-250 - 400 -60S-Percale, White upon approved design and sample approval by the Architect / Engineer-in-charge upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Duvet cover - king (Size: 104"x94"), of 100% Cotton-250 to 400 tcc-60S- 1 CM Satin Stripe, White upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Duvet-Quilt- King (Size: 102"x92"), 300 GSM-Super Soft Filling-Quilted-Polyester Micro Fabric Shell upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Pillow Cover - Large (Size: 20"x37"), Bag Type-100% Cotton-60S-300 TC-1 CM-Satin Stripes upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Pillow Cover - Regular(Size: 20"x30") , Bag Type-100% Cotton-60S-300 TC-1 CM-Satin Stripes upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Pillows - Large (Size:20"x36"), Denier Fibre 1.5 Filling-500Grams upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Pillows - Regular (Size:20"x30"), Denier Fibre 6 Filling-500Grams upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Pillow Protector - Large (Size:20"x37"), 100% Water Proof Terry Top - Zipper Closure upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Pillow Protector - Regular (Size:20"x30"), 100% Water Proof Terry Top - Zipper Closure upon approved design and sample approval by the Architect / Engineer-in-charge

Supplying of Cushions ,Designer Fabric + Poly Fill Cushions (Size:16"x16") upon approved design and sample approval by the Architect / Engineer-in-charge

CURTAINS

Supplying and fixing of Main curtain, brand D'Décor or any aooroved make for all rooms, with polyester based cotton blend pleated curtains upon approved design and sample approval by the Architect / Engineer-in-charge. Including all fixing charges and necessary fittings. Base rate of fabric is Rs.700/-

Supplying and fixing of Sheer curtain, brand D'Décor or any approved for guest room , of polyester based pleated curtain upon approved design and sample approval by the Architect / Engineer-in-charge. Including all fixing charges and necessary fittings.Base rate of fabric is Rs.500/-

Supplying and installation of Black out roman blinds with glass fabric (Low PVC light control with high solar reflection index and to provide privacy combined with low shading co-efficient) upon approved design and sample approval by the Architect / Engineer-in-charge. Including all fixing charges and necessary fittings. Base rate of fabric is Rs. 700/-

Supply of machine tuffed polypropylene Textured Carpet with Rubberised Cushion backing as per details given below. The carpet shall have minimum production yarn weight equivalent in range of Oz per square yard as mentioned below. The carpet shall have sufficient gauge with sufficient stitches 1/10 per inch. The carpet shall be made of 100% solution dyed fibre content. The carpet should carry a warranty not less than 15 years from the manufacturer and supplier of carpets. The carpet shall have the pile height ranging from 2.5 mm + / - 0.5mm and total thickness of the carpet tile shall also range from 6mm + / - 0.5mm. The carpet shall have anti-static properties as per the manufacturers specifications and as approved by the Architects. The Carpet shall also be Stain and Soil resistant as per the manufacturers specifications. Shampooing of carpet to be done before site is handed over.The work includes peripheral stiching to form decorative finish as approved by the Architect/Enginner-In-Charge Bedrooms

Formal Living

Lounge

Bathrooms

FIXED FURNITURE

Providing and fixing 600mm wide wardrobe consists of carcase with both side leather laminate pressed 19mm thick BWP 710 grade plywood with 2mm thick edge band with profile lighting at hanging space, end panel with 40mm thick end panel using 19mm thick plywood with 4mm thick ash veneer and wooden edge band, back panel with both side leather laminate pressed 12mm thick BWP 710 grade plywood, flutted wooden shutters, drawers fitted with smooth glides and lock. The cost shall include the price for auto closed self closing hinges, ss ball bearing telescopic slide/ drawer channel, drawer lock with two reversible keys, 10mm dia ss satin finish pull handles & 15mm dia dress hanging rod, all complete upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 600mm wide dress rack consists of carcase with both side leather laminate pressed 19mm thick BWP 710 grade plywood with 2mm thick edge band with profile lighting at hanging space, end panel with 40mm thick end panel using 19mm thick plywood with 4mm thick ash veneer and wooden edge band, back panel with both side leather laminate pressed 12mm thick BWP 710 grade plywood, flutted wooden shutters, drawers fitted with smooth glides and lock. The cost shall include the price for auto closed self closing hinges, ss ball bearing telescopic slide/ drawer channel, drawer lock with two reversible keys, 10mm dia ss satin finish pull handles & 15mm dia dress hanging rod, all complete upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 600mm wide luggage rack consists of carcase with both side leather laminate pressed 19mm thick BWP 710 grade plywood with 2mm thick edge band with profile lighting at hanging space, end panel with 40mm thick end panel using 19mm thick plywood with 4mm thick ash veneer and wooden edge band, back panel with both side leather laminate pressed 12mm thick BWP 710 grade plywood, flutted wooden shutters, drawers fitted with smooth glides and lock. The cost shall include the price for auto closed self closing hinges, ss ball bearing telescopic slide/ drawer channel, drawer lock with two reversible keys, 10mm dia ss satin finish pull handles & 15mm dia dress hanging rod, all complete upon approved design and sample approval by the Architect / Engineer-in-charge

Providing cubicle system in shower & changing room locker with compact laminate 3mm thick(side and back partition) and 9mm thick (top, bottom& shelves) with single colour of HPL boards and 3 tier locker with size of column 450x450x450 with acessories standard make aluminium, stainless steel 304 grade accessories: Aluminium interlocking supporting channels, SS cam locks with door number plate,SS hinges -SS, door stopper rubber lining, SS screws and pvc wall plugs and open locker for hanging dress complete upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 600mm wide, 1800mm long basin bottom storage consists of carcase with 19mm thick BWP 710 grade plywood with 4mm thick teak veneer and wooden edge band, 16mm thick BWP 710 grade plywood flutted wooden shutters. The cost shall include the price for auto closed self closing hinges,drawer lock with two reversible keys, 10mm dia ss satin finish pull handles , all complete as specified and as directed by the Engineer-in-Charge

Providing and fixing 600mm wide, 2600mm long basin bottom storage consists of carcase with 19mm thick BWP 710 grade plywood with 4mm thick teak veneer and wooden edge band, 16mm thick BWP 710 grade plywood flutted wooden shutters. The cost shall include the price for auto closed self closing hinges,drawer lock with two reversible keys, 10mm dia ss satin finish pull handles , all complete upon approved design and sample approval by the Architect / Engineer-in-charge

MOVABLE FURNITURE

Providing, supplying & fixing of armchairs and frame & legs are made up of Ashwood having Light walnut finish polish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of Heigh back armchairs and frame made up of Ash wood and legs made up of Ashwood with carving having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of Heigh back armchairs with wheels and leather back rest. The complete back is contoured to provide the needed lumbar support for long seating hours. The seat is made up of moulded foam, upholstered with leather.SYNCHRO MECHANISM: The mechanism installed for this chair is a Synchro-1 mechanism. This mechanism provides you with the utmost comfort while leaning backwards. There is a displacement in the ratio of 1:3 between seat and back respectively The Synchro mechanism is designed with 360 Degree revolving feature, Tilt tension adjustment and Upright locking. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12 cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal is made of nylon with glass reinforcement and fitted with 5 nos. twin wheel castors.(castor wheel dia. 5.0cm.) TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in 30% Glass Filled black Nylon. Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge.All exposed faces finished with PU polish for wood frames .

Providing, supplying & fixing of armchairs and frame & legs are made up of Ashwood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of armchairs and frame & legs are made up of Ashwood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of armchairs and frame & legs are made up of Ashwood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of arm chairs and frame & legs are made up of Ash wood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of visitors armchairs and frame made up of Ash wood and legs made up of Ashwood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing,supplying & fixing of 4 drawers ,Frame/Carcase shall be made up of Ashwood with CNC engraved design and legs made up of ashwood upon approved design and sample approval by the Architect / Engineer-In-Charge. All exposed faces finished with Light walnut finish polish for wood frames. Provide drawer accessories with sliding channels (Hettich brand).

Providing and fixing of art display stand having 18mm thick Carcase made up of Green Club plywood or hard wood framework upon approved design and sample approval by the Architect / Engineer-In-Charge. The exposed surface were provided with impored marble or tile.

Providing & fixing console with the Carcase of 18mm thick BWP Green Club plywood or hardframe wih Ash veneer & legs shall be made up of Ashwood upon approved design and sample approval by the Architect / Engineer-In-Charge. Shutter were engraved with CNC and having Antique white polish.

Providing & fixing console with the Carcase of 18mm thick BWP Green Club plywood or hardwood frame and legs shall be made up of Ashwood upon approved design and sample approval by the Architect / Engineer-In-Charge. Shutter were provided with leather shutter and having Light walnut finish polish.

Providing & fixing study table with the Carcase of 18mm thick BWP Green Club plywood or hardwood frame wih 4mm tk Ash veneer upon approved design and sample approval by the Architect / Engineer-In-Charge.Legs shall be made up of Ashwood and provided with two shutters and having light walnut finish polish.

Providing & fixing media console / study table with the Carcase of 18mm thick BWP Green Club plywood or hardwood frame provided with 2 drawers upon approved design and sample approval by the Architect / Engineer-In-Charge.Legs shall be made up of Ashwood and having light walnut finish polish.

Providing & fixing media console with the Carcase of 18mm thick BWP Green Club plywood or hardwood frame wih 4mm tk Ash veneer upon approved design and sample approval by the Architect / Engineer-In-Charge. Top & legs shall be made up of Ashwood. Shutter are provided with cane shutters and having light walnut finish polish.

Providing & fixing media console with the Carcase of 18mm thick BWP Green Club plywood or hardwood frame wih 4mm tk Ash veneer upon approved design and sample approval by the Architect / Engineer-In-Charge. Top & legs shall be made up of Ashwood. Shutter are provided with cane shutters and having light walnut finish polish.

Providing, supplying & fixing offire storage cabinet and Carcase of 16mm thick BWP Green Club plywood and provided with 16mm tk laminated shutters and having light walnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing,and fixing wall mirror of size 600mmx1800mm in position of 5mm thick extra clear mirror frame made up of Ashwood with CNC engraved design upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing,and fixing wall mirror of size 900mmx1200mm in position of 5mm thick extra clear mirror frame made up of Ashwood with CNC engraved design upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing and fixing of sculpture stand having made up of Brickwork with granite coping upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table and the top shall be made up of Ashwood & legs shall be made up of Brass leg and having Antique Brass finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table and the top shall be made up of Marble & legs shall be made up of Brass leg and having Light walnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table and the top shall be made up of Ashwood & legs shall be made up of metal and having Light wallnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table with 2 drawers and 2 knob and the top shall be made up of 18mm thick BWP Green club plywood or hardwood framework with 4mm thick ash veneer & legs shall be made up of ashwood and having Light wallnut finish polish and accessories having hinges of Hettich brand upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table and the top shall be made up of 18mm tk BWP Green club plywood/hardwood frame work with marble top & legs shall be made up of Ashwood and having Light wallnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table and the top shall be made up of 18mm tk BWP Green club plywood/hardwood frame work & legs shall be made up of Ashwood upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table and the top shall be made up of 18mm tk BWP Green club plywood/hardwood frame work with marble top & legs shall be made up of Ashwood upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing side table and the top shall be made up of 18mm thick BWP Green club plywood or hardwood framework with 4mm thick ash veneer & legs shall be made up of ashwood and having Light wallnut finish polish.

Providing & fixing side table with 2 drawers and 2 knob and the top shall be made up of 18mm thick BWP Green club plywood or hardwood framework with 4mm thick ash veneer & legs shall be made up of ashwood and having Light wallnut finish polish and accessories having sliding channels of Hettich brand.

Providing & fixing of 198x183 mm cot and frame works made up of BWP marine grade plywood or hardwood and provided with fabric headboard and having finished Light walnut polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing of 198x183 mm cot and frame works made up of BWP marine grade plywood or hardwood and provided with fabric headboard of imported fabric and having finished Light walnut polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing of 198x183 mm cot and frame works made up of BWP marine grade plywood or hardwood and provided with fabric headboard and having finished Light walnut polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing of book shelf and top portion shall be made up of 18mm thick BWP Green Club plywood or hardwood frame work with 4mm thick ash veneer & legs shall be made up of Ashwood legs and having Light walnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge.Shutters are provided with Ashwood frame and accessories having hinges of Hettich brand.

Providing & fixing of 90mm diameter centre table and metal centre table having finished with Antique brass upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing dining table and the top and legs shall be made up of Ashwood and having Light wallnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of dining chairs and frame & legs are made up of Ash wood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric of Italian leather upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing console and top or frame shall be made up of Ashwood and Legs are made up of metal upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing of Crockery shelf and top portion shall be made up of 18mm thick BWP Green Club plywood or hardwood frame work with 4mm thick ash veneer & legs shall be made up of Ashwood legs and having Light walnut finish polish.Shutters are provided with Leather shutter and accessories having hinges of Hettich brand upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of study chairs and frame & legs are made up of Ashwood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing coffee table and the top shall be made up of 18mm thick BWP Green club plywood or hardwood framework with marble top & legs shall be made up of ashwood and having Light wallnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of coffee chairs and frame & legs are made up of Ash wood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing conference table and the top & legs shall be made up of ashwood and having Light wallnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of office chairs with wheels and frame made up of Ash or hardwood with matching finish or walnut finish upon approved design and sample approval by the Architect / Engineer-In-Charge.seat and back are made up of 1.2 cm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam. The complete back is contoured to provide the needed lumbar support for long seating hours. The seat is made up of moulded foam, upholstered with fabric. ARMRESTS: The Arm rest is injection moulded in Polypropylene fitted to the seat base . SYNCHRO MECHANISM: The mechanism installed for this chair is a Synchro-1 mechanism. This mechanism provides you with the utmost comfort while leaning backwards. There is a displacement in the ratio of 1:3 between seat and back respectively The Synchro mechanism is designed with 360 Degree revolving feature, Tilt tension adjustment and Upright locking. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12 cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal is made of nylon with glass reinforcement and fitted with 5 nos. twin wheel castors.(castor wheel dia. 5.0cm.) TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in 30% Glass Filled black Nylon. Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric.All exposed faces finished with PU polish for wood frames .

Providing, supplying & fixing of office chairs with wheels and leather/rexin back rest upon approved design and sample approval by the Architect / Engineer-In-Charge. The complete back is contoured to provide the needed lumbar support for long seating hours. The seat is made up of moulded foam, upholstered with fabric.SYNCHRO MECHANISM: The mechanism installed for this chair is a Synchro-1 mechanism. This mechanism provides you with the utmost comfort while leaning backwards. There is a displacement in the ratio of 1:3 between seat and back respectively The Synchro mechanism is designed with 360 Degree revolving feature, Tilt tension adjustment and Upright locking. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12 cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal is made of nylon with glass reinforcement and fitted with 5 nos. twin wheel castors.(castor wheel dia. 5.0cm.) TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in 30% Glass Filled black Nylon. Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric.All exposed faces finished with PU polish for wood frames .

Providing & fixing working table and the top shall be made up of 18mm thick BWP Green club plywood or hardwood framework with 4mm thick ash veneer and having Light wallnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of Pouf and frame are made up of Ash wood having Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing center table and the top shall be made up of 18mm thick BWP Green club plywood or hardwood framework with 4mm thick ash veneer and having Light wallnut / Antique brass finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing of centre table and top portion shall be made up of 18mm thick BWP Green Club plywood or hardwood frame work with 4mm thick ash veneer and having Light walnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing discussion table and top & legs shall be made up of Ashwood having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Supply & fixing two seater sofa with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with imported fabric of GenuineLeather and having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Supply & fixing two seater sofa with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m densitywith Art leather and having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Supply & fixing two seater sofa with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with imported fabric of Art Leather and having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Supply & fixing two seater sofa with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with imported fabric of GenuineLeather and having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Supply & fixing three seater sofa with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m densitywith Art leather and having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Supply & fixing three seater sofa with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m densitywith Art leather and having Light walnut finish ploish.

Supply & fixing four seater sofa with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with ART Leather and having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of Arm Seater with Upholstery and frame are made up of 18mm tk BWP Green club plywood/hardwood frame work & legs are made up of Ash wood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with Art Leather upon approved design and sample approval by the Architect / Engineer-In-Charge

Supply & fixing Arm Seater with Upholstery with Frame structure made of 18mm thick BWP Green Club Plywood or hardwood frame work and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with Art Leather and having Light walnut finish ploish upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of Arm Seater (Double seater) with Upholstery and frame are made up of 18mm tk BWP Green club plywood/hardwood frame work & legs are made up of Ash wood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with Art Leather of imported fabric upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of Arm Seater (Single seater) with Upholstery and frame are made up of 18mm tk BWP Green club plywood/hardwood frame work & legs are made up of Ash wood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with Art Leather upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing, supplying & fixing of Arm Seater with Upholstery and frame are made up of 18mm tk BWP Green club plywood/hardwood frame work & legs are made up of Ash wood having Light walnut finish ploish, Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density with Art Leather upon approved design and sample approval by the Architect / Engineer-In-Charge

Providing & fixing dressing table and the top shall be made up of 18mm thick BWP Green club plywood or hardwood frame and legs shall be made up of ashwood and provided with 2 shutters and having Light wallnut finish polish upon approved design and sample approval by the Architect / Engineer-In-Charge

MODULAR KITCHEN

Providing and fixing 2 door work top chiller (120x 60x100cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Table top fryer made of 316 grade SS sheet and are fitted with appropriate heating elements with thermostatic temperature controls, rotary switchs, indicating lmps ans fibre coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing wall mounted cabinet (120x30x60cm) with door, made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing masala table with under shelf (40x70x100cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 2 burner chinese cooking range (120x 70x125cm) with under shelf, made of 1.5mm 316 grade SS sheet. and are fitted with appropriate heating elements with thermostatic temperature controls, rotary switchs, indicating lmps ans fibre coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing single bowl sink with cross support (60x70x100cm) made of 316 grade SS sheet and sink units tops shall have sunk (N)shape and with 15cms splash back on the wall side unless otherwise specified upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing dosa tawa with pipe under shelf (120x70x100cm) made of 1.5mm thick 316 grade SS sheet, side panels made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing granite top table with under shelf (115x70x100cm) made of 1.2mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Wall mounted salamender, made of 316 grade SS sheet. All inner supporting frames made of SS 316 L angles. Equipment will br mounted on 40x40 square tube with adjustable nulone leg bush upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Mobile tandor top (75x75x100cm) made of 1.5 mm thick and side made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing wall mounted double skin exhausted hood made of 316 grade SS sheet with air ventilations, and will be mounted on 40x40 square tube with adjustable nylone leg bush,etc upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 2 burner indine cooking range (120x60x100cm) made of 316 grade SS sheet, and are fitted with appropriate heating elements with thermostatic temperature controls, rotary switchs, indicating lmps ans fibre coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing bulk cooking range (60x 60x45cm) made of 1.5 mm thick and 1mm thick 316 grade SS sheets, and are fitted with appropriate heating elements with thermostatic temperature controls, rotary switchs, indicating lmps ans fibre coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Bain marie counter with OHS and sliding doors (150x70x145cm) made of 316 grade SS sheet and are fitted with appropriate heating elements with thermostatic temperature controls, rotary switchs, indicating lmps ans fibre coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Pickup counter with OHS and sliding doors (110x70x145cm) , top made of 1.2 mm thick and sides 1mm thick 316 grade SS sheets upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing mobile work table with 2 under shelf (90x60x85cm) made 1mm thick 36 grade SS sheets upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing wall mounted cabinet with door (90x30x60cm) , made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing drain trough (size:30x30x15cm) made of 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 2 burner cooking range 1 Indian, 1 Chinese with u/s (120x70x100cm) with under shelf, made of 1.5mm 316 grade SS sheet. and are fitted with appropriate heating elements with thermostatic temperature controls, rotary switchs, indicating lmps ans fibre coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Chappathi plate with pipe under shelf (90x70x100cm) made of 316 grade SS sheet, and are fitted with appropriate heating elements with thermostatic temperature cotrols rotary switchs, indicating lmps nad fibr coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing griddle plate with under shelf (60x 70x100cm) made of 316 grade SS sheet, and are fitted with appropriate heating elements with thermostatic temperature cotrols rotary switchs, indicating lmps nad fibr coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing wall mounted cabinet with door (100x 30x60cm) , made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing granite top table with under shelf (65x70x100cm) made of 1.2mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 2 burner cooking range (120x70x100cm) with under shelf, made of 1.5mm 316 grade SS sheet. and are fitted with appropriate heating elements with thermostatic temperature controls, rotary switchs, indicating lmps ans fibre coated wires upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing preparation table with sink and cross support (120x60x100cm) made of 1.2 mm thick 316 grade SS sheet and sink units tops shall have sunk (N)shape and with 15cms splash back on the wall side unless otherwise specified upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing work table with under shelf (95x60x100cm) made 1mm thick 36 grade SS sheets upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 2 tier wall shelf (120x 30x20cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 2 tier wall shelf (95x 30x20cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 4 tier storage rack (150x45x180cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 4 tier storage rack (100x45x180cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing pallet stand (size:100x50x20cm)made of 316 grade SS, with necessary fittings, etc upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 2 door vertical chiller (75x75x210cm) made of 316 grade SS sheet with necessary fittings,etc upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing work table with 2 under shelf (170x70x100cm) made 1mm thick 36 grade SS sheets upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing wall mounted cabinet (170x30x60cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing work table with sink ( 150x60x100cm) made of 1.2 mm thick 316 grade SS sheet and sink units tops shall have sunk (N)shape and with 15cms splash back on the wall side unless otherwise specified upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing wall shelf (150x 30x20cm) made of 1mm thick 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing drain trough (size: 30x30x15cm) made of 316 grade SS sheet upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing of Potato peeler made of 316 grade SS sheets, with necessary fittings etc upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing cutting table with (60x60x100cm) made 1mm thick 36 grade SS sheets upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing work table with sink and cross support (120x60x100cm) made of 1.2 mm thick 316 grade SS sheet and sink units tops shall have sunk (N)shape and with 15cms splash back on the wall side unless otherwise specified. As per design approved by architects.

Providing and fixing 2 door vertical freezer (75x75x210cm) made of 316 grade SS sheet with necessary fittings,etc upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Tilting Grinder 15L made of 316 grade SS sheet, with necessary fittings upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Atta Kneder 10kg made of 316 grade SS sheet, with necessary fittings. upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing 3 bowl sink with chut (180x 60x100cm) made of 1.2 mm thick 316 grade SS sheet and sink units tops shall have sunk (N)shape and with 15cms splash back on the wall side unless otherwise specified upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing Dish washing machine made of 316 grade SS sheet, with necessary fittings,etc upon approved design and sample approval by the Architect / Engineer-in-charge

Providing and fixing wall mounted pot rack (size:180x30x15cm) made of 316 grade SS sheet, with necessary fittings,etc upon approved design and sample approval by the Architect / Engineer-in-charge

EXTERIOR DEVELOPMENT

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Procuring healthy grass free from weeds and foreign materials and laying on the soil medium as turfing upon approved design and as directed by Architect / Engineer-in-charge. The rate include for grass cost, transport to site, cost and application of manure, planting, labour, supervision and maintenance for 2 months after planting Pearl Grass

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge. .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Royal palm

Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Foxtail palm

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge..Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Bismarkia palm

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge. .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Jackfruit tree

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge.Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Elenji tree

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge.Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Coconut tree

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge.Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Malpighia Topiary in steel mesh

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge..Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Eugenia Topiary

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge.Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Clerodendrum Inerme -Hedge

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge.Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Murraya Exotica - Flower bush

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge.Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Heliconia Caribea

Procuring and planting specified nursery grown trees, shrubs and other plants upon approved design and as directed by Architect / Engineer-in-charge..Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting. Areca tree

Supplying , stacking and spreading sludge / well decayed farm yard manure from thesource upon approved design and as directed by Architect / Engineer-in-charge incl. screening, loading, unloading, conveyance and stacking at site.

Disposal of earth work by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 5 km for all lifts, complete upon approved design and as directed by Architect / Engineer-in-charge.

Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered). Depth exceeding 1.5 m but not exceeding 3 m

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site.

Dry stone pitching 22.5 cm thick laid in courses and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete. (Payment for Stone to be made separately).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Weather shade, Chajjas, corbels etc., including edges

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Edges of slabs and breaks in floors and walls. Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer?in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer?in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick)

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia M.S. bars 4 nos on each side, including setting in position in footpath to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse sand), having joint thickness not more than 5mm except on curve, including filling of joints with same cement mortar and making grooves etc. complete as per direction of Engineer-in-charge.

Water fountain including supply, installation, complete. As per landscape architect's design

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer?in-charge).

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in?charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete. New work (Two or more coats)

Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level. Cement mortar 1:6 (1 cement : 6 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. Granite of any colour and shade

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross?section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in?built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Float glass panes. 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).

Providing and fixing ball bearing for rolling shutters.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

Dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometre, as per direction of Engineer-in-charge.

DORA INFRASTRUCTURES AND PROPERTIES PVT LTD