construction of medical gas plant room

Amount

Earthwork in excavation by manual means over area for leveling purpose including disposal of excavated earth up to 1m from cutting edge, and should be disposed in Near-by all kinds of soil. Total= 20.50mᵌ

Providing and laying of cement concrete (1:4:8) Using 40 mm nominal size Nallah stone. Total= 20.50mᵌ

P/L in position cement concrete of specified grade excluding the cost of centering shuttering-all works up to plinth level 1:3:6 ( 1 cement:3coarse sand:6 Nallah stone aggregate of 40mm nominal size ) Total = 15.20 mᵌ

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead up to 50m and lift up to 1.5m. Total = 5.18mᵌ

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centenng. shuttering, finishing and reinforcement-All work upto plinth level 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) Total = 12.69m3

Brick Work:- Brick work with common burnt clay F.P.S (non-modular) bricks of class designation 75 in foundation and plinth in (1:6)mix 1cement : 6 coarse sand (wall of height 10ft) Net Qty. of Brick work = 25.50mᵌ (approx.)

Design, Providing and Laying of MS-Round steel bars of different dia. i.e. 16mm, 12mm, 10mm and 08mm for Stirrups for horizontal beams, vertical columns, roof linter and flooring including cutting, bending, straightening, hoisting, laying and fixing of steel bars. Thermo-Mechanically Treated bars Total Quantity = 60 qtl (approx.)

15 mm cement plaster on both sides of brick wall in (1:4) mix (1 cement: 4 fine sand):-outside area as well as inside area and roof. Total Area of Plaster after deductions of Doors and Windows including Main Gate:- Net Area under Plaster= 300m² Approx

Reinforced cement concrete work in floors having slope upto 15°, excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) Area:-30ft x 30ft x 6 inch Total Area = 12.6 m3

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Total Area = 300m2 (Approx.)

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface Total Qty. = 300m²

Distempering with 1st quality acrylic washable distemper (readymade) of approved manufacturer and of required shade/ colour.

Finishing walls with exterior water proofing cement paint of required shade (two or more coats)

Providing and fixing Powder coated aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete. Total Weight of = 175 kg

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. with float glass panes of 8 mm thickness (weight not less than 20.0 kg / sqm) Total Area: 4.41M2 (Approx.)

Providing and fixing powder coated anodized aluminium grill with opening of 2 inch and having thickness 10mm with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws@ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening. Total Weight = 35 Kg (Approx.)

Providing and Laying of Complete Electrical Circuit in the medical gas pipeline plant room by way of Laying of PVC flexible Pipe 3/4’’ – 80 mtr., Modular Electrical Wall Boxes – 06 No., Laying of Copper Wire 1.5 sqm – 05 rolls, Copper Wire 2.5 sqm – 02 rolls, Copper Wire 4sqm – 03 rolls, Copper Wire 6sqm = 02 rolls, P/F of 16 amp electrical Switches and Sockets – 10 No., 06 Amp. Switch – 14 no., 10Amp. Socket – 14 no., LED PANEL Lights of size (2ft x 2ft) – 10 No., in the false ceiling of the plant room, Electrical LED Bulb Holders- 14 no., Electrical LED Bulbs 12 Watt – 14 no., Ceiling Fan 48 inches - 04 No. Complete Job including laying & fitting of the circuit, material, skilled labour charges, testing the complete circuit on load and all taxes as applicable.

Design, Fabrication and Fixing of MS-Pipe Gate of Size (08 ft x 08 ft) by way of steel work in built up square, rectangular including cutting, hoisting, fixing in position weighing approx. 12 quintals along with fixing of 1 inch square type weld mesh on the MS-Gate of the plant room and applying a priming coat of approved steel primer including welding and bolting with special shaped washers etc complete hot finished seamless type tubes. The job includes cost of material, tools and tackles, skilled labour charges, carriage, transportation, all taxes applicable. Complete Job

M/S MOHD AAMIR

M/S SHRI ANUBHAV GANDOTRA