Construction of 1x5 MVA Sub-Station at I.A. Pocket-B Utelwa Distt. Amethi.

Supply and planting English rose plants Ashoka, pendula, mango, Neem etc. in beds including cost of all materials labor and T&P etc required for proper completion of the work. (Sl no. 23.13)

S/L of Control Cable for metering complete as per direction of E/I (2.5 sq. mm, 2 core copper) (Gloster /Havells/ Grandlay/Polycab/KEI make)

S/E of Terminal Gantry of R.S. Joist-175x85 mm 19.5 Kg/Mtr. 6.1 Mtr. above the ground and 1:3:6 cement concrete foundation mounted on a stone pad of 300x300x75 mm complete in all respect as per direction of E/I

Supply, Errection, testing & Commissioning of 33 KV VCB 750 MVA/1250 Amp., 1500 MVA 25 KA Motorized complete with CT, PT with structure complete in all respect as per approval of UPPCL and enlisted latest vendor list

S/E of Bus Bar gantry structure of 105 Lbs/Rail Pole 6.5 Meter long 5.2 Meter above in ground level with 33 KV section Isolator complete in all respect as per direction of E/I

S/E of 33 KV lighting arrestors with structure made of MS channel 125x65 mm 3.1 Kg./M top of MS angle 50x50x6 mm, 4.5 Kg/M Lighting Arrestor (one set of lighting arrestor shall be installed on gantry) complete in all respect as per direction of E/I

Supply, Erection, testing & Commissioning of outdoor type with copper wound 5 MVA power transformer with on load tap changer as per UPPCL with following provisions.(a) Cable termination box with disconnecting facility for 33 KV XLPE cable outdoor arrangement with 33 KV bushings at 33 KV side. (b) Cable termination box with disconnecting facility with 11 KV bushings for 11 KV XLPE cable at 11 KV side. (c) On load tap changer +5% to -15% (d) Bi directional roller (e) Conservator with drain valve & sump value. (f) Earthing terminals (Two) (g) Double diaphragm explosion vent (h) Radiator with top & bottom shut of valve (i) First filling of oil including makeup fill (j) Silica gel breather with oil seal (k) Rating and Diagram plate (l) Air release plug (m) Buchholz relay with shut off valves on both sides.(n) Winding temperature Indicator (WTI) (o) Oil Temperature indicator (OTI) (p) Magnetic oil level gauge (q) Pressure relief device (r) Marshalling Box (s) Tap position indicator (t) Marking plate for OLTC (u) Terminal marking plate (v) Drain valve with plug & locking arrangement (w) Filter valve (x) Oil sampling Valves (03 Nos.) (first quality material as per latest amendment in indian standard and approved by UPPCL and enlisted latest vendor list.)

S/F of 33 KV pin insulator with pin on main terminal gantry, as per direction of E/I. (first quality material as per latest amendment in indian standard and approved by UPPCL) as per latest approved vender list of MVVNL

S/F of 33 KV with 11 KV 4 Nos. Set B&S type strain disc insulators 120 KN E&M strength complete in all respects as per direction of E/I (first quality material as per latest amendment in indian standard and approved by UPPCL) .Busbar in two section as per latest approved vender list of MVVNL

S/F of P.G. Clamp suitable for panther conductor for jumpring complete in all respect as per direction of E/I as per latest approved vender list of MVVNL

S/F of overhead line with ACSR Panther Conductor on pole/service bracket including binding etc.

Construction of 33 KV transformer plinth suitable for 33/11KV transformer (1x10 MVA) as per drawing with all material, labour and T&P etc.required for proper completion of the work as per specifications of UPPCL as per drawing & as per direction of E/I

S/F of Fencing of 2.7 M height of chain link 2"x2" wire with Intermediate of T iron complete in all respect as per direction of E/I

Construction of Boundary Wall for the fencing complete in all respect as per direction of E/I

S/B of 40 mm dia x 4.5 meter long GI Pipe earthing as per PWD Sch. No. 701.

S/F of 50x6 mm GI strip from earth electrode directly complete in all respect as per direction of E/I

S/F of 33 KV Post insulator 2x22 KV of approved quality complete in all respect as per direction of E/I

S/F of 63 amp DP MCB (10 KA) CAT ‘A’ complete in all respect PWD Sch.No. 1011 Catt-A Type

(Civil Building and Boundry Item)Excavation in foundation in ordinary soil (Loam clay or sand) including lift up to 1.5 mtr. And lead up to 30m and including filling watering and ramming of exacavated earth into the Grenaches or into the space between the building and sides of foundation vetches’ or in to the all nuts and removed and disposal of surplus earth as directed by the Engineer. Charge up to a distance of 30 mm from the foundation Grenaches.(sl no 251)

Job No: ED-III (232) Date. 30.06.2025

Supply, Fixing, installation, testing & Commissioning of 11 KV VCB Panel as per latest specification outgoing 11 KV complete with 1250 Amp., 350 MVA, 600/300/5 Amp. CT ratio with PT 1 Nos. incoming panel and 800 AMP., 350 MVA, 400/200/5 Amp. 4 Nos. Outgoing panels as per approval of UPPCL and enlisted latest vendor list

S/F of Jointing kit 185 sq. mm indoor type 11 KV heat shrinkable type complete in all respect as per direction of E/I (Raychem/Denson/Birla make)

S/F of Jointing kit 18 sq. mm outdoor type 11 KV heat shrinkable type complete in all respect as per direction of E/I (Raychem/Denson/Birla make)

S/F of Jointing kit 300 sq. mm indoor type 11 KV heat shrinkable type complete in all respect as per direction of E/I (Raychem/Denson/Birla make)

S/F of Jointing kit 300 sq. mm outdoor type 11 KV heat shrinkable type complete in all respect as per direction of E/I (Raychem/Denson/Birla make)

S/F of Jointing kit 70 sq. mm indoor type 11 KV heat shrinkable type complete in all respect as per direction of E/I (Raychem/Denson/Birla make)

Supply & fixing of lugs for Cable (10 sq. mm) as per PWD Sch. No. 504 I

S/laying of 70 sq. mm, 3.5 core Aluminium conductor PVC Insulated, armoured, served, sheathed cable 1100 V grade as per PWD Sch. No. 501 (m). (Gloster /KEI / Havells/ Grandlay/Polycab make)

S/laying of 10 sq. mm, 2 core Aluminium conductor PVC Insulated, armoured, served, sheathed cable 1100 V grade as per PWD Sch. No. 501 (b) (Gloster/ KEI / Havells/ Grandlay/Polycab make)

S/f of fire extinguisher, dry chemical type 6.00 Kg. capacity as per PWD Sch. No.1131 (A).

Construction of Control cable trench of required size 0.30x 0.45 Mtr. complete in all respect as per direction of E/I

S/B of 600x600x6mm G.I. Plate earthing with GI Strip as per PWD Sch. No. 702

S/filling of 20 mm stone grit in yard of size 26x36 Mtr. 75 mm thick complete in all respects as per direction of E/I

S/F of 100 mm dia GI Pipe "B" class for protection of cable on pole complete in all respect as per direction of E/I SIDC Sch. No ER 25.1

S/F of earth mat in the switch yard of the sub-station for all Electrical Equipments and structure by laying of M.S. rod of 32 mm in 750 mm deep trenches and earth electrode 3 Mtr. long MS round bar 32 mm dia 0.5 Mtr. belowground level as per detail specification of UPPCL complete in all respect as per direction of E/I

Painting of terminal gentry, lighting arrestor, Busbar gentry, line isolator & Bus isolator structures, post insulator, fencing, Poles and other structure complete in all respects as per direction of E/I

Supply, installation, testing & Commissioning of battery charger 24V/40 Amp. float cum boost battery charger with dropping diodes suitable for I/P 230V+-10% 1 phase 50 Hz type FCBC as perUPPCL specification

S/E testing & Commissioning of 63 KVA 11/0.4 KV Aluminium wound outdoor type Transformer, latest Level as per conforming IS, as per BIS as per direction of E/I (first quality material as per latest amendment in indian standard and approved by UPPCL)

S/F of fire bucket, round bottom made of GI sheet 9-11 Liters capacity as per PWD Sch. No. 1133

S/F of shock treatment chart as per PWD Sch. No. 1134.

S/L of 1800x900x12 mm thick chequered rubber matting as per PWD Sch. No. 1136.

S/F of 11 KV TPMO with insulator complete in all respect as per direction of E/I. (Jaishree, azad, Rama make)

S/L of 70 sq. mm, 3 core 11 KV XLPE cable complete in all respect as per direction of E/I (Gloster /Havells/ Grandlay/Polycab/KEI make)

S/L of 185 sq. mm, 3 core 11 KV XLPE cable complete in all respect as per direction of E/I (Gloster /KEI / Havells/ Grandlay/Polycab make)

S/L of 300 sq. mm, 3 core 11 KV XLPE cable complete in all respect as per direction of E/I (Gloster / Havells/ Grandlay/Polycab/KEI make)

S/F of outdoor type 11 KV fuse set with insulator complete in all respect as per direction of E/I 23(Jaishree, azad, Rama make)

S/F of brass nickel plated compression gland 10mm x 2 core as per PWD Sch. No. 503 (b)

S/F of brass nickel plated compression gland 70mm x 3.5 core as per PWD Sch. No. 503 (m)

Providing steel furniture with 1 No. table & four No. chairs complete in al

l respect etc.

S/Providing of 1.98 MVAr. Capacitor Bank complete in all respect as per UPPCL and latest vendor list

Supply & Erection of Steel Tubular Pole 410-SP-29, 9 Mtr. Long complete with 1/6th of overall length of pole in cement concrete with 30 cm dia cement plinth around the pole and 30 cm above the ground level.The Foundation of underground will be of cement conrete in the ratio of 1:3:6 alround the pole. The brick ballast used will be of 1.2 cm size with stoone pad 30cmx30cmx7.5cm at the base. The cost includes all materials including MS Pole Cap complete in all respect As Per SIDC No. 2(a) II Bottem section G.I

Supply & Fixing of 415 V metal clad TPN rewireable type switch fuse unit an angle iron bracket complete in all respect as per UPPWD Sch. No. 315

Supply & Wiring of sub-main with 2 Nos. of 2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistarnd copper condcutor cable in existing conduit complete with supply of all material labour and T&P required for proper completion of work as per PWD Sch. No. 289.

S/E of Double Pole structure on 410-SP-55, 11 Mtr. Long ST Pole Complete With All Respects as per SIDC Sch. No. ER 04.2

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 110 to 130 Watt. Confirming to IP 66 Protection complete in all respect. as per PWD Sch. No. 1424 Cat-AA (first quality material as per latest amendment in indian standard )

Painting of ST pole and all mountings on it with two coats of aluminium paints with an under coat of red oxide paint on length of above 10 M. support above the ground level as per direction of Engineer in-charge of work/site including T&P , men & material required for proper completion of work as per SIDC Sch. No. 20.2

Supply & fixing anticlimbing device fabricated from G.I. flat of 25mm x 6 mm size in a shape of ring of the pole size, having G.I.flat pointed fins of length 225 mm in 8 nos. and also barbed wire in 200 mm length above the said ring including material as per SIDC Sch. No.26.1

Supply & fixing of danger board fabricated from 10 guage M.S. sheet as per I.E. Rules as per SIDC Sch. No. 27.1

(Internal Wiring)Supply and fixing of approved quality celling fan including all cost all materials labor, T&P etc. from proper completion of the work. (NSI)

Wiring point for light with 1.5 sq. mm. far. P.V.C. insulated multistrand and single core copper conductor cable in P.V.C. conduit pipe concealed in the wall, complete with 14 SWG copper earth continually wire, Piano type switch & celling rose/angle/button holder on 3 mm thick phenolic laminated backelite sheet etc. complete in all respects as directed including matching colour wash. (PWD Sch.No. 131(B)

Digging pits of 60cm dia and 60 cm deep in ordinary soil and refilling the same with excavated earth mixed with manure of sludge in the ratio of 2:1 by volume and flooring with earth dressing including removal of rubish and Surplus earth if any with all leads and lifts etc (cost of manure and earth local sand to be paid separetely) (Sl no. 23.09)

Fixing galvanized corrugated iron roofing 24 BWG in position including supply of material labour and T&P etc. required for proper completion of work. (Sl no. 23.09)

Wiring point for fan fresh air fan (light duty exhaust fan) in PVC conduit with 1.5 sq. mm FR PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit.(PWD Sch.No. 133(B)

Wiring point for plug with 1.5 sq.mm FR. PVC insulated multistrand single core copper conductor cable in P.V.C. conduit concealed in the wall, complete with 14 SWG copper earth continuity wire piano type switch and socket etc. complete in all respects including matching colour wash. (PWD Sch.No. 134(B)

Supply and burying of 600 mm *600 mm*6mm Gi plate vertically for earthling with its top at least 3 meters below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthling lead of one no 8 to 10 SWG copper wire in 15mm dia G.I. piper and copper wire will be extra 30 mm square C.I. frame with hinged cover misery housing alternate layers of charcoal coke and salt at least 150 mm thick alluring etc. complete in all respect PWD Sch.No. 704

Supply & wiring of submains with 2 nos. 4 sq mm & with 1 Nos. earth wire of 2.5 sq mm for FRLSH PVC insulated copper conductor cube in existing PVC conduit complete including supply of all material labor and T&P etc required for proper completion of the work as directed by Engineer in charge as per UPPWD sch. No. 291 (A).

Supply and fixing of 6 amp. to 32 amp DP MCB (10 KA) as per UPPWD sch. No. 1009 Catt. B Type

Wiring point for exhaust fan/power plug in PVC conduit with 1.5 sq. mm FR insulated multistrand copper conductor cable as earth wire drawn inside the conduit. (PWD Sch.No. 137(B)

Supply and fixing of 63 Amp S.P. isolator as per UPPWD sch. No. 1004(B)Catt. B Type

Local filling in plinth including supply of necessary quality of local sand outside the UPPCL premises including watering dressing etc. Rate to under cost of all materials labor and T&P etc. required fbr proper completion of work (local from approved local quarry) .(sl no 255(a))

Concrete with 4 cm gauge 1st class brick ballast (class 150) fine sand (F.M. 1.8 to 2.5) and. cement in proportion of 10:05:1 in foundations and under floors including supply of all materials labor and T & P etc. required for proper completion of work .(sl no 274)

1st class brick (class 150) work in 1.6 cement & fine sand (F.M. 1.8 To 2.5) mortar in foundation & plinth including supply of all materials, Labor and T&P etc. required for proper completion of work.(sl no 303)

1st class brick (class 150) work in 1.6 cement & fine sand F.M. (1.8 to 2.50) mortar but in supper structure but for wall of one brick thick including supply of all materials, labor T&P required for proper completion of work. (sl no 303)

Cement concrete with 2cm gauge approved hard stone ballast coarse sand (F.M 1.8. to 2.5) & cement in propertied 1:2:1 including supply of all materials, labour, side shuttering if required and T&P etc. required for proper completion of work..(sl no 279(a))

Mild’s steel 01 iron in plain work such as reinforced concrete or reinforced brick work (when not included in over all rate) wrought to required shape as necessary including bending for proper completion of the work & including supply of steel its wastage, bend, books and authorized over lapping shall be measured, steel shall not be supplied by the department. (sl no 504 a&b)

Mild steel or iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof work gates etc, wrought to required form including bolts nuts wastage etc. and their fixing required for proper completion of the work steel is not supplies by the Department.(sl no 9.03)

Providing M.S. frames work for B.C.C. Trench covers and edging with M.S. Angles including cutting bending and vending of M.S. angle and cutting and welding of M.S. bars for reinforcement and lifting books as per approved design. The rate is including cost of all labour, materials etc proper completion of the work. (sl no 502)

Concreting of 40 mm thick RCC trench covers in mild steel frame work with c.c. 1:1:5:3 in cement. Coarse sand and 2 cm gauge graded hard stone ballast with 3 mm thick loathing coat of near cement finish on top of cover complete with all labor, materials T&P etc. required for proper completion of the work but excluding gust of frames.(sl no 5.19)

Hall brick thick (115 mm) wall with 1 class brick (class150) in cement mortar 1:4 cement & coarse sand in super structure 1/c supply of all materials labor and T&P etc. required for proper completion of work.(sl no 6.03+6.07+6.09) (5050+240+210+105)

Supply and fixing water proof craft paper in double layer with grease in between over 4 mm thick c.c. 1:1.5:3 in cement coarse sand & 12 mm gauge stone grit (c.c. 1:1.5:3 shall be paid separately .(sl no 10.13)

S/F hexagonal fan box with hexagonal side of approx 800 mm in length fabricated from 16 SWG MS sheet incorporating 10mm dia. M.S. round bar duly bent for supporting fan hanger duty pained with red oxide and screwing arrangement with wiring conduit mid in the RCC roof before concerting along with supply of all material labour, T&P. etc required to proper completion of the work.(sl no 11.49)

R.C.C. work with cement approved course sand (F.M.1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast in proportion 1:2:4 in linters of doors & windows excluding supply of reinforcement and its bending but including its fixing & windows excluding supply of reinforcement and its bending but including its fixing & binding the same with 24 BWG G.I. binding wire and including necessary centering & shuttering etc. and also including cost of all materials labor and T&P etc required for proper completion of the work.(sl no 283)

R.C.C. work with cement approved coarse sand (F.M. 1.8 to 2.50) and 2 cm gauge graded approved hard stone ballast in proportion 1:1:5:3 for lighter leam excluding supply of reinforcement and its bending but including its fixing & binding the same with 24 BWG G.I. binding wire and I/C necessary centering & shuttering etc. and also I/C cost of all materials labor and T&P etc. required for proper completion of work.(sl no 285)

12 mm thick plaster with cement in proportion 1:2 cement and fine sand of 1.8 TO 2.5 Line ness modulus over brick work minimum thickness not to be less than 10 mm including supply of all materials labor and T&P etc required for proper completion of the work.(sl no 583)

12 mm thick plaster with cement in proportion 1:6 cement and fine sand of 1.8 To 2.5 Lineless modulus over brick work minimum thickness not to be less than 10 mm including supply of all materials labor and T&P etc required for proper completion of the work. Add for extra labor and materials for plaster over though over though face of one brick thick wall. .(sl no 11.10+11.15)

12 mm thick plaster with cement in proportion 1:2 cement and fine sand of 1.8 To 2.5 Lineless modulus over brick work minimum thickness not to be less than 10 mm including supply of all materials labor and T&P etc required for proper completion of the work.(sl no 11.10)

12 mm thick plaster with cement mortar consisting of 1:4 of approved cement and coarse sand mortal including supply of all materials labor and T&P etc required for proper completion of the work same as above in item no. 24.(sl no 584(a))

Providing (12x15) mm section groove in plaster at the junction of selling & walls, including all material labor and T&P etc required for proper completion of the work .(sl no 11.19)

R.C.C. work with cement approved coarse sand (F.M. 1.8 to 2.50) and 2 cm gauge graded approved hard stone ballast in proportion 1:1:5:3 for lighter lead excluding supply of reinforcement and its bending but including its fixing & binding the same with 24 BWG G.I. binding wire and I/C necessary centering & shuttering etc. and also I/C cost of all materials labor and T&P etc. required for proper completion of work.(sl no 284)

R.C.C. columns in 1:1:5:3 proportions of cement fine sand and 20 mm graded hard approved stone ballast R.C.C. columns e

xcluding. Supply of reinforcement and its bending but including its fixing & binding the same with 24 BWG G.I. binding wire and including necessary centering & shuttering etc. and also including cost of all materials labor and T&P etc. required for proper completion of work.(sl no 289).

40mm thick 1:2:4 floor without base concrete floor with cement approved coarse sand & 2cm graded approved stone ballast (shingle for barely lard in panels finished with 3 mm floating coat of near cement of cement and marble dust in ratio of 5:1 as specified and giving them a uniform finish including supply of all labor and T&P etc. required for proper completion of work.(sl no 605)

2 cm thick plaster or dado or skirting consisting 1 part of cement and 2 parts of approved coarse sand laid in panel finished with 3 mm floating coat of neat cement or cement and marble dust in ration 5:1 including supply of all materials, labor and T&P etc. required for proper completion of work.(sl no 597)

Supply and fixing of single leaf flush door shutter (boiled water resistance, phenol maldehlje resin boded, not pressed factory made commercial quality to ISI 2202 part-a (1983) ISI marked including fixing of wooden cleats and stoppers and including fixing and adjustment of hings including their supply of approved anodized aluminum fittings (a) 32 mm thick (sl no 8.80(a)+8.59)/(470(a))

Supply and fixing of single leaf flush door shutter (boiled water resistance, phenol maldehlje resin boded, not pressed factory made commercial quality to ISI 2202 part-a (1983) ISI marked including fixing of wooden cleats and stoppers and including fixing and adjustment of hings including their supply of approved anodized aluminum fittings (b) 35mm thick double leave door shutter.(sl no 8.80 (b)+8.80 (d)+8.59)/(470(b))

Supply and fixing galvanized mosquito proof zall 14*24 gauge with M.S. flat of 20*3mm size on both sides screwed or welded to window or door frame.(sl no 455)

p/f steel glazed window & ventilators of standard rolled man or mohair steel sections conforming to is 7452-1974 as per drawing joints metered and welded with 100*14*3.15mm hold fast embedded in cement concrete lock 15*10*10 cm size of 1:3:6 proportion i.e. 1 part cement 3 parts as approved coarse sand and 6 parts of graded stoma (aggregated 20mm nominal size including s/f of glass panes plain pin headed 4mm thick nuts glazing clips and special putty of approved make complete & including a cost of red oxide paint the fabrications should confirming to 1.5. 1038 to 1975 (aluminum beading with rubber packing included 20 Kg/Sq.mtr.(sl no 9.24)

Painting or varnishing on new iron work in small areas or new wood work with one coat of ready mixed priming paint and three coats of approved superior quality ready mixed paint (Luxor) or equivalent brand or varnish I/C supply of all materials babour T&P etc. required for proper completion of work. Paint to be used should conform I.S. 103-1950.(sl no 642+643)

Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement prime of ICL or equivalent brand for smothering and leveling of the surface as per requirement and direction of engineer including cost of all material labor T & P etc required for proper completion of work. .(sl no 13.21)

3mm thick floating coat of Neat cement finish over roof & walls including supply of materials labor and T&P etc. required for proper completion of work (cement consumption 0.444 tag/sq.m.(sl no 20.23)

Supply and fixing of 110mm dia PVC pipe 6 kg./sq, cm for water supply making &rain water pipe of Tirpati or equi. make with special such as tee, bend, socket, elbow, etc including cutting of pipe where necessary and including excavation of trenches for laying the pipe line of approved sixe (600*900mm)and including its back filling after testing the pipe line, watering ramming etc. complete including disposal of suiplusmeth from the sides 100 mtr as per defection of engineer uncharged as required for proper completion of work.(sl no 26.64a)

Supply and fixing of 75 mm dia PVC pipe 6 kg./sq, cm for water supply making &rain water pipe of Tirpati or equi. make with special such as tee, bend, socket, elbow, etc including cutting of pipe where necessary and including excavation of trenches for laying the pipe line of approved sixe (600*900mm)and including its back filling after testing the pipe line, watering ramming etc. complete including disposal of suiplusmeth from the sides 100 mtr as per defection of engineer uncharged as required for proper completion of work.(sl no 26.64c)

Supply and fixing of 50 mm dia PVC pipe 6 kg./sq, cm for water supply making &rain water pipe of Tirpati or equi. make with special such as tee, bend, socket, elbow, etc including cutting of pipe where necessary and including excavation of trenches for laying the pipe line of approved sixe (600*900mm)and including its back filling after testing the pipe line, watering ramming etc. complete including disposal of suiplusmeth from the sides 100 mtr as per defection of engineer uncharged as required for proper completion of work..(sl no 26.64e)

R/F glass strip of 3.15mm thickness in points of floor and skirting at the time of laying, floors flush with floor level including labor, Tools and plants etc. complete (a) of 25 mm depth.(sl no 631(a))

Providing and fixing 550 mm*400 mm wash hand basin of white glazed Carton ware first quality I.S.I. marked (Hindustan Neycer/cera make) with R.S. or C.I. bracket painted white 15mm dia C.P. brass pillar cock with C.P. metal handle (weight not less than 400gms) I.S.I. marked and 32 dia C.P. brass waste standard pattern with check nut 32mm dia C.P. brass or “s” trap and unions complete with P.V.C. connection 5” size including supply of all materials labor and T&P etc. Required for proper completion of the work and including cutt

ing and making good the walls and floor with cement coarse and githi fittings uses should of superior quality. .(sl no 27.07)

Providing and fixing 600mm*450mm beveled edge mirror of Atul,Kiran make glass with Indian polish 6.50mm thick complete with back of 600mm*450mm*6 mm hard board sheet fixed to wooden cleats with C.P. brass screws and washers including supply of all materials labor and T&P etc. required of proper completion of the work .(sl no 27.23a)

Providing and fixing 750mm*20mm size C.P. brass towel rill of approve quality (weight 275 gms. Including brackets with pair of C.P. brass brackets to fit the size of towel rail fixed on the wall on wooden cleats with C.P. brass screw including supply of all materials labor and T&P etc. required for proper completion of work and cutting and making good the wall plaster etc. required to work. .(sl no 27.25)

Providing and laying and joining 100 mm dia stone ware pipe line first quality perfect make with special where necessary in proper slope with still mixture of cement (1.30 bag /30 m and line san (0.45cum / 30m in proportion of 1:1 including testing of joints etc completely spun yarn 4.50kg / 30 mtr and including supply of all materials labor T&P etc. required for proper compilation of work. .(sl no 27.71)

Supply and fixing Nahani Trap India make of heavy approved quality complete with brass grating Nahani Trap laid over base cement concrete 1:6:12 including cost of cement supply of all materials labor and T&P etc. required for proper completion of work. .(sl no 27.70)

Proving and fixing 100 mm dia C.P. grating over Nahani Trap of drain holes including cost of all materials labor and T&P etc. required for proper completion of the work. .(sl no 27.87)

Supply and fixing of brick bllast in soak pit including supply of all labor material T&P etc required of proper completion of work.(sl no 6.23)

Earth filling under floors and/or substation area when earth is obtained from outside UPPCL premises including cutting and cartage upto 3 km. cost of earth royalty and lilting ate site including watering ramming in 20 cm layers & dressing of earth etc complete.(sl no 4.11)

Providing and injecting chemical emulsion for pre construction anti-terminate treatment and creating a chemical barrier under and around the column pits, wall tranches basement excavation top surface of plinth filling junction of wall and floor along the external per meter of binding expansion joints shrouding of pipers and conduit etc. complete (plinth area of the building at ground floor only shall be measured as per I.S. 6313 (part II 1981) Airline emulsifialbe concentrate or another approved material such as Heptachlor or chlordance will be used. The rate of application of chemical shall be as follows 1 Treatment for Masonry & foundation 5 liters per sqm. 2. back fill in immediate contact with foundation 7.5 litters /sqm 3. Treatment of top surface of plinth filling 5 liters/sqm 4. Treatment junction of wall and the floor 5 liters/sqm 5. Treatment of soil along external parameter of building wall and the floors 7.50 .(sl no 17.01)

Providing barbed iron wire fencing including stretching fixing into the post including all labor all material and T&P required for proper completion of the work the weight of hot dipped GI barbed wire having 12 SWG- 2 ply wires and 4 points ordinary barbs @ 150mm (approx) CC should be 100gm per mtr. (Sl no. 9.913)

Finishing walls with water proofing cement paint of approved made like super snowcap or equivalent quality on new work with three coats ot given an even shade including supply of all materials labor T&P etc. required for proper completion of work (Sl no. 660+661)

First class brick on edge floor laid dry. Joints sand filled. Including preparation of base to proper slope and its ramming including supply of all material labor & T&P etc required for proper completion of the work (Sl no. 12.08)

R.C.C. works with cement approved coarse sand and 2 cm (3/4)”: gauge approved stone ballast in the proportion 1:1:5:3 (1 cement :6 aggregate in column excluding supply of reinforcement and its bending the same with 24 SWG binding wire and necessary centering and shuttering etc. and also including supply of all materials labours and tools and plants etc required for proper completion of works Strength of the concrete shall no be less then M-150 (Sl no. 5.17)

Supply and laying of 80mm thick cement concrete interlocking tiles grey coloured shaped over 40 mm thick layer of local sand including supply of all material labor and T&P etc including cost of sand required for proper completion of the work. (Sl no.12.27)

Supply and installation of single phase submersible pump of 1 H.P. outlet 32mm dia or more head 78/30, discharge 1100/2800 LPH of K.S.B. or equivalent make Iidia Marka hand pump-II including 150mm dia 70m deep boring up to second strata including supply and lowering 110mm to 63mm dia PVC pipe (4m 110m & 46m 43mm, 6 kg/sq/mtr.) with required strainer reducer joining 90mm dia long cylinder 32mm dia GI pipe 3m long including supply and filling of course sand of approved quality approx. 15 cu.m) including developing the bore well to a achive clear and sand free water for continuous 60min. including cost of all material labour and T&P and its cartage for installation of hand pump complete as per drawing including excavation of earth and laying 25mm c.c. floor 1:2:4 with cement c. sand and 20mm stone ballast with water proofing compound over 100mm thick c.c.1:6:12 with cement c sand and 40 mm brick ballast and making side edge 115mm thick and 300mm deep with brick work 1:4 and plaster the same with 1:4 mix with neat cement finish also including 115mm wide drain in 1:4 brick work & plaster all around the peripheral of platform complete including supply of all materials labour and T&P required for proper completion of the work. (Sl no. 22.80)

One priming coat and two coat oil distemper on new work including supply of all materials labor and T&P etc. required for proper completion of work (Sl no. 13.17+13.14)

Providing and laying of 10mm thick virtified floor tiles of approved brand and sample in size 600*600 mm of first quality of bell, Johnson or equivalent make shade color and pattern as approved by Engineer in charge laid over base cement mortar 1:4 mix including finishing the joints etc required for proper completion of work. (Sl no. 12.26a)

Flooring with 19mm thick keta stone or skirting over base cement mortal 1:4 max and joined with grey cement slurry mixed with pigment to match the shade of slab including supply of all materials labor and T&P etc. required for proper completion of work. (Sl no. 12.24)

R/F glass strip of 3.15mm thickness in points of floor and skirting at the time of laying, floors flush with floor level including labor, Tools and plants etc. complete (a) of 40 mm depth (sl no 631(b))

2.5 cm thick 1:2:4 plain cement concrete floor with cement approved coarse sand & 2 cm graded approved stone ballast (single for Bareilly lad in panels finished with 3 mm floating coat of neat cement of cement and marble dust in ratio of 5:1 as specified and giving them a uniform finish including supply of all labor and T&P etc required for Proper completion of work.(sl no 631(a))

Providing and fluxing first quality white glazed “Orissa” pattern W.C. pan 80mm Hindustan Cera make with 10 cm. H.C.I. ‘P” Trap approved make with 10 liters high level C.I. lusting cistern (Hindustan sunifa. Ashok make) I.S.I. marked with siphon brass lifting and G.I. chain pull R.s. or ci. Bracket 32 mm dia. G.I. flush pipe “b” class 2m with brass unions etc. 32mm die G.I. bend 32 mm dia G.I. Secker 15mm dia overflow pipe with specials and mosquito proof couplings of approved municipal lasing 15mm dia brass stop cock (400gms plastic connect 1.5”*a*1” with brass unions including supply of all materials labor and T&P etc required for proper completion of the work and painting of cistern and fittings with apricot paint cutting and making good the walls and floors where required with cement sand and grit. The seat and trip shall have to be fixed over minimum 3” thick c.c. in proportion of 12:6:1 including supply of all materials labor and T&P etc. complete. (sl no 27.02a)

S/laying chicken mesh of (20mm) hexagonal heavy quality over roofs joints of roof as per direction of the Engineer in charge (Sl no. 27.33)