Construction of SIB OCR Complex at Minicoy. SH - Construction of Office Building, 2 Nos Type II Quarters, Cycle Shed, Garage, Toilet Blocks, Guard Room, Reception, Visitors Longue, Compound Wall, Sump, Well, Septic Tank, Soak Pit and Manhole

Amount

Surface dressing of the ground including removing vegitation and in equalities not exceeding 15cm deep and disposal of rubbish lead up to 50 metres and lift up to 1.5 metres

Earth work excavation in foundation trenches or drains not exceeding 1.5m in width or 10 sq.m on plan including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of (a) Upto 1.50 m.

(b) Up to 1.50 metre to 3 metres (pie x0.7x0.7xh)

(c ) Up to 3.00 metre to 4.50 metres (pie x0.7x0.7xh)

(d) Up to 4.50 metre to 6.00 metres (pie x0.7x0.7xh)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc layers not exceeding 20cm in depth consolidating each deposited layers by ramming and watering lead up to 50 mtr and lift up to 1.5 metres

Providing and laying cement concrete 1:4:8 (1 cement 4 M. sand 8 graded stone aggregate 40mm nominal size) excluding the cost of centring and shuttering and reinforcement for foundation and plinth

Providing and laying cement concrete 1: 5:10 ( 1 cement: 5 M. sand:6 granite chips ) foundation and plinth.

Providing and laying damp proof course 40mm thick with cement concrete 1:2:4 ( 1cement 2 M. sand 4 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work 1:1.5:3 (1 cement 1.5 M. sand 3 granite chipps 20mm nominal size excluding cost of centring,shuttering and reinforcement .

foundation footing base of coloum etc and mass concrete

Reinforced cement concrete work in (wall any thickness ) including attached pilasters, buttresses, plinth and string course, fillets, columns, pillars, piers, abutments, post and struts etc.. up to floor five level excluding cost of centering and shuttering finishing and reinforcement.1:1.5:3 ( 1 cement :1.5 M. sand :3 graded stone aggregate 20 mm nominal size

Reinforced cement concete work 1:1.5:3(1 cement, 1.50 M.sand, 3 granite chips 20mm nomnal size) excluding cost of centering, shuttering and reinforcement. Beam,Suspended floors, roofs,having slope upto 15 degree landings, shelves, chajjas, lintels, beams, plain window sills,staircase and spiral stair case up to floor five level

Reinforced cement concrete work in well sterning excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 (1 cement 2 M sand 4 graded stone aggregate 20mm nominal size)

Providing and fixing up to floor two level precast reinforced cement concrete 1:2:4 (1 cement 2 M sand 4 graded stone aggregate 20mm nimnal size) set in position with cement mortar 1:2 (1 cement 2 M sand) and finished smooth with 6mm thick cement plaster 1:3 (1 cement 3 M sand) on exposed surface including centring and shuttering in baffle wall and slab.

Centring and shuttering including strutting, propping etc. and removal of form for Foundation footing base of coloum etc and mass concrete. Coloum

Centring and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform.

Centring and shuttering including strutting, propping etc. and removal of form for Lintel, beam, plinth beams,bressumer and cantilevers

Centring and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts.

Centring and shuttering including strutting, propping etc and removal or form for Stairs, (excluding landings) except spiral-staircases.

Centering and shuttering including strutting propping etc. ad removal of form work for well sterning

Cold twisted steel reinforcement for R.C.C work including bending, binding and placing in position complete.

Brick work with modular bricks of class designation in foundation and plinth in cement mortar 1:6 ( 1 cement 6 M. sand)

Brick work super structure above plinth level in cement mortar 1:6 ( 1 cement 6 M. sand) upto floor five level.

Half brick work masonry in super structure above plinth level C M 1:4(1 cement;4 M. sand)

Providing wood work in frames of doors, windows , clearestory windows and other frames wrought, framed and fixed in position complete I1nd class Teak wood

Providing and fixing 30mm thick panalled glazed or panelled and glazed shutters for doors and windows and clestory windows including anodised aluminium butt - hinges with necessary screws I1nd class Teak wood . Including 4mm thick glass panes.

Providing and fixingI1nd class Teak wood 25 mm squre wooden bars at required spacing in wooden frames of windows and clerestory windows

Providing 40X5mm Iron hold fast 40cm long i/c fixing to frames with 10mm dia bolts, nuts and wooden plugs and embedding in cement concrete blocks of sizes 30x10x15cm of mix 1:3:6 ( 1 cement 3 river sand 6 graded stone aggregate 20 mm nominal size)

Providing and fixing brass tower bolt (barrel type) with necessary screws etc complete.

Providing and fixing brass handle with necessary screws etc complete.

Providing and fixing brass door latch with necessary screws etc complete. (a) 300x16x5 mm

(b) 250x16x5mm

Providing and fixing bright finished brass casement stay with necessary screws etc complete 250mm weighing not less than 280 gms

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/ Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer- in-charge. (Glazing and panelling to be paid for separately):

For fixed portion anodised aluminium(anodised transparent or dyed to required shade according to Is: 1868 minimum anodic coating of grade AC15)

Providing and fixing aluminium work for doors, widows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/ Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer- in-charge. (Glazing and panelling to be paid for separately):

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Providing and fixing 12mmthick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing anodised aluminium grill (andised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existng window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cuttingb the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge.

Providing and fixing glazing in aluminium door,windows,ventilator shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architechtural drawings and the directions of engineer-in-charge. With float glass panes of 5.5 mm thickness

Providing and fixing bright finished Brass door stopper with rubber cusions and necessary screws etc.complete.

Providing and fixing bright finished brass hydraulic door closer with necessary screws etc.complete.

Providing and fixing aluminium tubular bar 32 mm outer dia, 3 mm thick & 2100 mm long with SS screws etc.complete as per direction of engineer-in-charge. Anodised (AC 15) aluminum tubular handle bar

Providing fixing 100mm brass lock (best make of approved quality) for aluminium doors including necessary cutting and making good etc.complete.

Providing and fixing anodised Aluminium tower bolt (barral type) anodised transparent or dyed to required colour and shade with bolts , nuts and screws etc complete. a) 225 mm x 10mm

b) 100 mm x10mm

Providing and fixing anodised aluminium hooks and eyes anodised transparent or dyed to required colour and shade with necessary screws etc complete. 200mm

Providing and fixing anodised Aluminium handles anodised transparent or dyed to required colour and shade with bolts , nuts and screws etc complete. 100 mm

Providing and fixing brass handle with necessary screws etc complete.100 mm

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge.

Providing and fixing to existing door frames 24 mm thick factory made PVC door shutters made of style and rails of UPVC hollow section of size 59 X 24 mm and wall thickness 2 mm +/- .2 mm with in built edging on both sides the styles and rails mitres and joined at the corners by means of MS galvanized / plastic brackets of size 75 X 220 mm having wall thickness 1.0 mm and stainless steel screws the styles of the shutter reinforced by inserting galvanized MS tube of size 20X20 mm and 1 mm / -.1 mm wall thickness. The lock rail made up of H section, a UPVC hollow section of size 100 X 24 mm and 2 mm +/- .2 mm wall thickness fixed to the shutter styles by means of plastic /galvanized M.S.U cleats. The shutter framed filled with a UPC multi chambered single panel of size not less than 620 mm. Having overall thickness of 20 mm and 1 mm +/- 0.1 mm wall thickness the panels filled vertically and tie bar at two places by inserting horizontally 6mm glavanized MS rod and fastened with nuts and washers complete as per manufacture's specification and sirection of Engineer-in-charge.(For WC and bathroom door shutter).

Providing and fixing Stainless steel(Grade 304) railing made of hollow tubes, channels,plates etc., including welding, grinding,buffing, polishing and making curvature (wherever required) and fitiing the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fastners, stainless steel bolts etc,. of required size on thetop of the floor or the side of waist slab with suitable arrangements as per approval of EIC( for payment purpose only weight of stainless steel members shall be considred excluding fixing accessoires such as nuts, bolts, fasteners etc.)

Cement concrete flooring 1:2:4 (1 cement 2 M.sand 4 stone aggregate) finished with a loating coat of neat cement including cement slurry, rounding of edges and strips etc. But excluding the cost of nosing the steps etc. complete. including Neat cement punning (a) 40 mm thick with 12.50mm nominal size to aggregate.

Providing and fixing ceramic Anti skid glazed floor tiles of size 300x300mm (thickness to be specified by the anufacture ) of first quality confirming to IS:15622 of approved make,in colours such as White , ivory, Grey,Fume red brown,laid on 20 mm thick cement mortar 1:4 (1cement, 4 plastering sand ) and joining with white cement and matching pigment etc... complete.Department shall be provide Cement Contractor has to be bring the tiles.(Kajariya/Jonson/Bell)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to IS:15622 ( thickness to be specified by the manufacture ) of approved make,in all colours,shades except burgundy ,bottle green,black of any size as approved by engineer-in-charge in skirting,risers of steps and dado over 12mm thick cement mortar 1:3 ( 1cement, 3 plastering sand ) and joining with grey cement slurry @3.3 kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.Department shall be provide Cement Contractor has to be bring Tiles.(F.C)(Kajariya/Jonson/Bell)

Providing and laying Mat finished vitrifid floor tiles (premium quality ) in diffren sizes ( thickness to be specified by the manufacture ) with water absorbtion less than 0.08 % and confirming to IS: 15622 of approved make in all coulers and shades, laid 20mm thick cement mortar 1:4 ( 1 cement 4 P. sand ) including grouting the joints with white cement and matching pigments etc.. complete. Size 800x800mm( flooring), Khajariya/Jonson/Bell or equivalent

Providing and laying Mat finished vitrified tiles (premium quality ) in diffrent sizes ( thickness to be specified by the manufacture ) with water absorbtion less than 0.08 % and confirming to IS: 15622 of approved make in all coulers and shades, in skirting,riser of steps,over 12 mm thick bed of cement mortar 1:3 ( 1 cement 3 P. Sand ) including grouting the joints with white cement and matching pigments etc.. complete. (Skirting), 800x800 mm, Khajariya/Jonson/Bell or equivalent

6mm cement plaster to ceiling 1:3 (1 cement 3 P. sand)

12mm cement plaster 1:6 (1 cement 6 P. sand)

15mm cement plaster 1:6 ( 1 cement 6 P. sand) on the rough side of single or half brick wall

Finishing with Delux Multi surface paint systm for interiors and exteriors using primer as per Manufactures specification. Two or more coats applied on wall @ 1.25 ltr/10 Sqm over and including one or more coat of special primer applied @ .75 lir/10 Sqm Teflon coated (Nerolac/Berger/Asian)

Providing and applying wall putty of approved brand and manufacture 2mm thickness over plastered surface to prepere the surface even and smooth complete. (Nerolac/Berger/Asian)

Painting Wood work with Deluxe Multi surface paint give an even shade.Two or more coats applied on @0.90ltr/10 sqm) over under coat of primer applied @ 0.75 ltr/10 sqm of approved and manufacture (Nerolac/Berger/Asian)

Painting on steel work Deluxe Multi surface paint two or more coats with superior ready mixed paint of approved brand and manufacture in all shades on new work to give an even shade , including priming coat (Nerolac/Berger/Asian)

Finishing wall with water proofing cement paint of of approved brand and manufacture of required shade on new work (three or more coats) to give an even shade

French spirit polishing for a new work (two or more coats) including a coat of wood filler with ready mixed polish of approved brand and manufacture.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This inclues joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (External work)

(a) 15 mm nominal bore

(b) 32 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This inclues joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work, including cutting chases and making good the walls etc.)

20 mm nominal bore

Providing and fixing CP brass bibcock of approved quality and manufacture complete. Conforming IS 8931 , 15mm nominal bore (Jaquar /cera/hindware)

20mm nominal bore (Jaquar /cera/hindware)

Providing and fixing CP brass stopcock of approved quality and manufacture complete. Conforming IS standard weighing not less than 810 gms ,15mm nominal bore (Jaquar /cera/hindware) 15 mm nominal bore

20mm nominal bore (Jaquar /cera/hindware)

Providing and fixing CP brass shower rose with 15 to 20mm inlet of approved quality and manufacture complete. 150mm dia(Jaquar /cera/hindware)

Providing and fixing GM full way wheel valve of approved quality and manuefacture complete. 25 mm nominal bore

Providing and fixing nominal guage PVC Pipe of approved quality complete with special flang compression type fittings including trenching and re filling etc. External work, 110mm nominal bare

Providing and placing water tank on terrace ( at floor level ) polythene water storage tank ISI : 12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet ,outlet and over flow pipe but without fittings and the base support for tank ( 500 ltr capacity )

( 1000 ltr capacity )

Providing anf fixing white vitrous China water closet Pedestal pan (European) type WC pans with white plastic seat and lid and rubber buffers, 15 white vitrous China low level flushing system of approved make with fittings and brackets 40mm flush bend, 20mm over flow pipe with complete including cutting and making good the walls and floors where required. White EWC with plastic seat and lid (Jaquar or equivalent)

Providing anf fixing white vitrous China wash basin wih RS or CI brackets painted white, 15mm C.P bras pillar tap and C.P brass chain and rubber plug 32mm C,P. brass waste of standrad pattern 32mm diametre and waste pipe complete including cutting and making good the walls and floors where required. White vitreous China Flat back wash basin 550x400mm with one 15mm C.P. brass pillar tap.(Jaquar or Equivalent)

Providing and fixing stainless steel A ISI 304(18/8) kitchen sink asper S 13983 with CI brackets stainless steel plug 40mm, including painting of fittings and brackets and making good the walls where required.

Kitchen sink with drain board 510x1040mm bowl depth 250mm

Providing and fixing 600x450mm mirror of superior glass (approved quality) complete with 6mm thick asbestose sheet ground fixed to wooden cleats with necessary screws and washers. (Cera or equivalent)

Providing and fixing towel rail brackets fixed to wooden cleat with CP brass screws with concealed ritting arrangement of approved quality and colour . 600 mm long towel rail brackets with total length of 645 mm,width 78mm and effective height of 88 mm ,weighing not less than 190 gms. (Cera or equivalent)

Providing and Fixing PTMT liquid soap container109 mm wide,125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour,weighing not less than 105 gms.

Providing and laying and PVC pipes grade "A" with stiff mixture of 1:3(1 cement 3 m. sand) including testing of joints etc. complete.

(a) 110 mm diameter

(b) 90 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement 5 M sand 10 graded stone aggregate 40mm nominal size) around the pipe 15cm thick as per standard design excluding cost of centring, shuttering and reinforcement. 100 mm dia

Supplying and Fixing Rolling Shutters of approved make.made of 80x1.25mm M.S.laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft, with brackets side,guides and arrangements for inside or outside locking with push and pull operation complete,including the cost of top cover and spring.

Providing and fixing on wall surface PVC waste and vent pipe with solvent cement including cutting jointing etc complete. A) 75mm dia pipes.

Providing and fixing nominal guage PVC Pipe of approved quality complete with special flang compression type fittings including trenching and re filling etc. External work. 63 mm nominal bore

Providing and fixing PVC pipe half round eaves gutter with M.S brackets including bolts and nuts and necessary fitting as per approved brand and manufacture etc.complete 100 mm (10kg/sqcms)

Providing and fixing PVC ball valve of approved quality and manufacture complete. 63 mm nominal bore

Providing and fixing cast iron Gate in approved patteren with locking arrangements and neat finishing with Delux Multi surface paint including priming coat

Quarters

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group A

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

3 pin 5/6 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing 3pin, 5A cealing rose on the existing junction box/ wooden block including connections etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying of LED Tubelight set 20w 1800 lumen 4 feet

Supplying of LED Lamp 9watts

Supplying of PVC Bulkhead with Suitable LED bulb

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying of exhaust fan 300mm BEE 5star rated

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 300 mm sweep

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

10 Amps Single pole and neutral

16Amps Single pole and neutral

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DBcomplete with connections, testing and commissioning etc. as required.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

8 way (4 + 24), Double door

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Office

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

3 pin 5/6 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing 3pin, 5A cealing rose on the existing junction box/ wooden block including connections etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying of LED Tubelight set 20w 1800 lumen 4 feet

Supplying of LED Lamp 9watts

Supplying of PVC Bulkhead with Suitable LED bulb

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying of exhaust fan 300mm BEE 5star rated

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 300 mm sweep

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

6 Amps Single pole and neutral

10Amps Triple pole and neutral

20Amps Triple pole and neutral

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DBcomplete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of changeover switch

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ complete with tinned copper bus bar, neutral bus bar, earthrecess, bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way , Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

8 way (4 + 24), Double door

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Trench cutting size 40cm width and 95cm depth including fillings of 5: +5 cm dry sand over and below the cable and paving of bricks/ RCC slab over the cable and filling and levelling the trench with sand including transportation of brick/ RCC slab etc and other materials from store yard to site and vice versa as reqired.

LT underground power cables as below including transportation of cables from stock yard to work site and vice versa

LT underground power cable size 2 x 10sqmm

LT underground power cable size 4x 16sqmm

kurian and varghese

JAIN BUILDERS