REPAIR TO WATER PROOFING AND JOINERY WORKS AND REPAIR/REPL OF DEFECTIVE ELECTRIC WIRING AND CONNECTED ITEMS ALONGWITH REPLACEMENT OF DBS REPLACEMENT OF METER BOXES AND FITTINGS AND FIXTURES INCLUDING AT AFS MADH ISLAND UNDER GE AF THANE

Amount

Removing existing water proofing treatment what so ever exist (except concret padding), and removing, including chhipping on concrete surfaceand debris/rubbish materials off the site all as specified.

M&L for roughening surfaces of old concrete floor by picking, sweeping clan and washing down with water to remove dust & brushing neat cement slurry with 3Kgs of cement per sqm etc all as specified & directed

M & L for 15mm thick screed bed or bedding layer in cement mortar 1:4 over RCC slab horizontal or vertical portion for laying water profing treatment all as spd.

Material and labour for Plain Cement concrete (PCC) padding in cement concrete (1:2:4), type BO (using 12.5 mm graded stone aggregate) finished even and smooth without using extra cement all as spd.

M&L for APP modified roof treatment over existing RCC roof with following specification:- (a) Applying bitumen primer @ 0.4 Liters/Sqm with density of 0.87 to 0.89 Kg/liters at 25 degree C on the prepared dry roof surface. (b ) Laying 3 mm thick APP membrane weight not less than 3.50 kg/sqm by torch application with minimum 10 cm side lap and 15 cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (c) Over the membrane provide a solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm prescribed by manufacturer complete all as specified

Taking down cement plaster on brick/stone or concrete surface including racking out joints, hacking for key, scrubbing down with water to receive plaster, including removing debris/rubbish materials off the site all as specified.

M&L for cement plaster in CM 1:4, 20mm thick in two coats (15+5) with using integral waterproofing compound finished even & smooth without using extra cement ( Note: Integral liquid water proofing compound to be used in per bag of cement shall be as per manufacturers instructions and paid separately under respective items.).

M&Lfor rendering 15mm thick in cm 1:6 finished with neeru finish as specified on fair faces of brick work or concrete surfaces.

M&L for rendering 5mm thick in cm 1:3 on fair faces of concrete as in soffit/ ceilling or slab, chhajjas finished even and smooth without using extra cement.

Supply only liquid water proofing compound (Make:- Scott No 1/Dr Fixit)

M&L preparing newly plastered surfaces ,and applying 2 coats of Oil Bound Distemper over a coat of alkali resistent primer Over 1 mm thick wall care putty on walls complete all as specified and directed by Engineer-in-Charge.

M&L Complete removal of existing treatment on old surface of walls and applying 2 coats of Oil Bound Distemper over a coat of alkali resistent primerOver 1 mm thick wall care putty on wallscomplete all as specified and directed by Engineer-in-Charge..

M & L for Preparation of new surfaces of ceiling and applying two coats of Oil bound distemper over a coat of primer.

M&L for applying two coats of acrylic water/weather proof exterior emulsion coating over one coat of primer all as per manufactures instructions including preparation of new/Old surfaces of wall/ complete complete all as specified and directed by Engineer-in-Charge.

Dismenrling floor hearth or wall tilling including cement mortar bedding ( but not backing) all as specified by Engr-in-charge.

M&L non skid ceramic tiles(Coloured) 7 to 8mm thick (square/rectangular) area of each tile exc 0.06sqm but n.exc 0.11 sqm, in in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge. NOTE :- Floor tiles repair with matching tiles in several Patches with proper levelling and fixing with existing tiles.

M&L Coloured Glazed Ceramic tiles 300 x 200 and 6-7mm thick on vertical surfaces such as skirting, dados and risers to steps etc including 10mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-Charge..

M&L Granite slab work 18 to 20mm thick in floors steps, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over & including screed bed 15mm thick in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Ditto as item No 18.00 above but as in vertical surface including 10mm thick backing coat in CM 1:4 .

Dismantling water tanks capacity 500 ltr including all fittings all as per specified and directed by engg-in-charge

S&F Rotational moulded polyethylene water storage tanks (cylindrical verticalwith closed top) with 500 litre capacity hoisted and fixed in position all as specified in SSR Part I

S&F ball brass valve, high pressure, with ploythene float and flynut complete, screwed for iron pipe or brass ferrule 20 mm bore.

Taking down chowkhats or frames exc 1.5 Sqm & n. exc 4 sqm with shutters without taking off shutters from the frame and removing to store

Taking down shutters of any description exc 1 sqm and n. exc 2 sqn each and removing to store

S&F factory made single exstruded WPC (Wood polymer composite) solid door/ window ceosetory window & other frames/ chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K Value 58-60 (suspension Grade) calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk ) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100N (Edge), minimum compressive strength of 58N/ mm2 , modules of elasticyty 900N / mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer -in - charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note :- For WPC Solid door/ window frames, minus 5 mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood polymer composite ) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 ((suspension Grade) calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk ) and non toxic additives (maximum toxicity index of 12 for 100 gms) f having minimum frame density of 650 kg/ cum, screw withdrawal strength of1800 N (Face) & 900N (Edge), minimum compressive strength of 50N/ mm2 , modules of elasticyty 850N / mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer -in - charge. Note Stainless steel butt hinges and necessary S S Screws shall be paid separately)

S&F PVC factory made wire gauged shutter with wire gauge warpped on an additional square 8mm MS solid tube and this tube shall be welded to MS tube. The wires gauge shall be stretched to tighten firmly, PVC door shutter 30mm thick (stiles) consisiting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm wigth stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail all as per specification and drawing given in SSR Part II, Schdule of rates 2010 and directed but as in four panels in lieu of two panels. Note : The wire mesh shall be measured separately.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as directed by Engr-in-Charge

M&L for cutting holes in bricks walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar or cement concrete 1:2:4 type B1 as required exc half brick but not exc one brick complete and as directed

S&F solid PVC double door frame of size 50mmx95mm made out of 5mm single side prelam PVC sheet reinforced with MS tube, supplying & fixing in opening as per specification and drawing

S&F factory made solid PVC moulded door shutter (single or double leaf) with particle board/wooden flush door core 28 to 30mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing

S&F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S&F 150mm long aluminium anodized barrel tower bolts of extruded section.

S&F 150mm extruded aluminium alloy handles fabricated type anodized.

S&F aluminium alloy anodized sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing botls and sliding bolts 300mm long

M&L for powder coated aluminium anodised (minium powder coating 50microns) window/ Openable Ventilators frames and shutters using standard aluminium anodised sections including necessary joining cleats, glazing clips, rubber packing anodised olurninium snap beading, screws, anodised aluminium fitting suitable rubber beading, nylon rollers, Nylon gaskit, concealed star lock, etc complete all as specified etc. complete of standard sections all as specified and directed ( Aluminium section shall be of make Jindal/Hindalco?Indalco) Note :- i) Weight of Aluminium sections for frames, shutters and 'C' or 'F' section for fixing of grill, glass and stainless wire mesh as applicable shall only be considered lex measurment for payment. ii) However cost of other consumable items shall be deemed in be included in the rate quoted. iii) Glass planes, anodized aluminium Grill and STainless steel wire mesh as applicable shall be measured and paid seprately as supplied only,

Supply only powder coated of approved colour aluminium grill of 5mm x 8mm bars size of opening 10 ems size mesh RG 103 ( as per Royal grill)

Taking down carefully point wiring and removing from site such as (Light,fan socket or power) Complete including fitting and fixtures,fan regulators switch boards,switches,ceiling rose's lamp holder from existing batten PVC conduit/steel conduit wiring complete excluding light fittings and fans all as specified and making good to the disturbed surfaces to match with existing ,complete all as specified and as directed

M & L for point wiring complete for light on independent /combine board with cable 1.5 sqmm (Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC casing & caping, hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for sunken GI terminal boxes Min 50mm deep ,suitable length and 1. 6 mm thickness for mounting, switches, sockets,fan regulator with 3 mm thick plastic laminated sheet cover fixed with cadmium plated screwed and cup washers, duly grouting and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced .( Make - Finolex/Anchor/Havells)

All as per Srl item No -39.00 here in before but for one socket outlet 5/6 amp on independent board complete all as specified and directed.

All as per Srl item No -39.00 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed.

All as per Srl item No 39.00 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed .

All as Srl item No 39.00 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed.

All as Srl item No 39.00 here in before but for call bell point complete all as specified and directed.

S & F in replacement switch piano flush type 5/6 Amps single pole one way complete all as specified and directed.

S & F in replacement switch piano flush type 5/6 Amps single pole two ways complete all as specified and directed.

S&F bell push flush type 5 Amp complete all as specified and directed .

S&F Electronic bell AC 230 Volt single pole ding dong type complete all as specified and directed .

S & F in replacement switch socket combination 5 pin, type 5/6 Amps flush type complete all as specified and directed.

S & F in replacement switch socket combination 6 Pin, 15/16 Amps flush type complete all as specified and directed.

S & F in replacement Socket outlet 5 pin 5 Amps flush type complete all as specified and directed

S & F in replacement Industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed.

S & F in replacement modular switch 5/6 Amps single pole one way,one module including modular cover plate with frame and metal flush box complete all as specified and directed .

S & F in replacement modular switch socket combination 5 pin, type 5/6 Amps5 in 1 flush type including modular cover plate and metal flush box with frame complete all as specified and directed .

S & F in replacement modular switch socket combination 6 Pin, 5/16 Amps flush type including modular cover plate with frame and metal flush box complete all as specified and directed.

S & F in replacement modular switch 5/6 Amps single pole two ways including modular cover plate with frame and metal flush box complete all as specified and directed.

S & F in replacement modular socket outlet 5 pin 5 Amps flush type including modular cover plate with frame and metal flush box complete all as specified and directed.

S&F in replacement modular bell push 5 Amp including modular cover plate with frame and metal flush box complete all as specified and directed.

S & F in replacement modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete including modular cover plate with frame and metal flush box all as specified and directed.

S & F ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified and directed.

Taking down carefully existing serviceable LED Tubelight/ bulkhead/ security light/ recess mount fitting of any size and refixing the same to respective location after carrying out cleaning all the components of fittings, including replacement of nuts, bolts and connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connectorcomplete all as specified and directed.

S & F in replacement LED Tubelight fitting with aliminium housing and integrated electronic driver, 20 watt having input voltage AC90-300V, 50 Hz , 6500K,surge protection min 4 KVA and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed Make Havells/Phillips/Crompton.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC surge protection 10 KVA outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.& Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 1 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed Make Havells/Phillips/Crompton.

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed

S&F LED lamp 9W for angle holder complete all as specified and directed

S & F timer switch with astronomical timer switch min 8KW, 3 pole, 230 V suitable for street light control including all assessories complete set all as specified and directed

S & F in replacement LED Water tight bulk head fitting 10 W,comprision of connector galvanised cast iron back plate,weather proof enamelled gallery ,glass well,and including 10 watt LED all as specified and directed Make :Havells/Phillips/Crompton

S&F in replacement LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.all as specified and directed Make : Havells/Phillips/Crompton

S & F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. all as specified. Make :Havells/Phillips/Crompton

S & F speed regulator for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S & F in replacement for Sub Main wiring with two single core 6 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade drawn in through flexible non metallic PVC casing caping with and including PVC insulated 6 Sqmm multi strand copper conductor as continuous earth wire in green colour connected to common earth dolly ,complete all as specified and as directed (Note : PVC cable and PVC casing caping shall be ISI marked) ( Make of cable - Havells/Anchor/Finolex) Note :- Two length of 6 Sqmm cable and one length of 6 Sqmm earth cable along with PVC casing caping will be measured as one running length

S & F in replacement for Sub Main wiring with two single core 4 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade drawn in through flexible non metallic PVC casing caping with and including PVC insulated 4 Sqmm multi strand copper conductor as continuous earth wire in green colour connected to common earth dolly ,complete all as specified and as directed (Note : PVC cable and PVC casing caping shall be ISI marked) ( Make of cable - Havells/Anchor/Finolex) Note :- Two length of 4 Sqmm cable and one length of 4 Sqmm earth cable along with PVC casing caping will be measured as one running length

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof IP 42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed ( Schneider /Havells / Legrand )

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 12 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof IP 42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed ( Schneider /Havells / Legrand )

S & F in replacement MCB ‘B’ series type suitable for 240 volts, AC supply 6 to 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed (Make - Schneider/Havells / Legrand )

S & F in replacement MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed (Make - Havells / Legrand / Schneider)

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted TP & N 4 ways, 415 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof, IP42 suitable for incorporation MCBs and isolators etc including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed (Make - Havells / Legrand / Schneider)

S & F in replacement MCB ‘B’ series type suitable for 415 volts, 10 KA, AC supply 40 to 100 Amps, triple pole and neutral (TPN) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed (Make - Havells / Legrand / Schneider)

Supply & fixing in replacement of meter box of size (0.9mX0.9mX0.2m) made of Polycarbonate shall have Transparent cover,should be weather/ vermin proof, anti-acid, anti corrosive, UV resistance, fire retardant, thickeness 2.25 mm double door,single opening with lock arrangement suitable for fixing 04 Electric meter & TPN DB box including taking down existing electric meters , refixing them with two single core PVC copper conductor unsheathed wire multistranded 4 sqmm,properly painting complete and fixing in wall with suitable cutting,cement & brick work etc all as specified and directed

S&F exhaust fan made of sturdy engineering plastic of 250mm sweep ,240 volt, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc. (Make : Havells/Orient/Crompton)

Jay Jyotirling construction co.

M/s Qureshi Construction Co

venus enterprises

M/s Mukesh Engineers

M/S KHUSHI ENTERPRISES