Interior and Renovation Work for the SIDBI Office RO BO at Chandigarh

Name of Work : Interior and Renovation Work for the SIDBI Office (RO/BO) at Chandigarh.

DETAILED SUMMARY

S.No. Sub-Head NDSR Amount (in Rs.)

1 Civil & Interior Works 17,81,704.43 50,54,618.45

5 CCTV AND NETWORK 0.00 6,22,450.00

6 Furniture Work 0.00 37,71,995.00

8 Add GST Multipluing factor of 1.0633 61,94,403.47

9 TOTAL i/c GST 1,71,52,990.00

Digitally signed by AMIT

Civil & Interior Works

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

CIVIL AND INTERIOR

1 PARTITIONS AND WALL CLADDING - -

WALL PANELING :-Providing and fixing Paneling upto ceiling height

consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling

channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick,

fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48 mm wide

having one flange of 34 mm and other flange 36 mm and 0.50 mm thick

fixed vertically within flanges of floor and ceiling channel and placed at a

spacing of 610 mm centre to centre by 6 mm dia bolts and nuts,

including fixing of studs along both ends of partition fixed flush to wall with

suitable anchor fastener or metal screws with nylon plugs at spacing of

450 mm centre to centre, and fixing of boards to both side of frame work

by 25 mm long dry wall screws on studs, floor and ceiling channels at the

spacing of 300 mm centre to centre. The boards are to be fixed to the

frame work with joints staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm

each) to be provided at the horizontal joints of two boards, fixed to the

studs using metal to metal flat head screws, including jointing and

finishing to a flush finish with recommended jointing compound, jointing

tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as

per manufacture's specification and direction of engineer in charge all

complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Paneling with 12 mm thick HDHMR board to IS: 5509

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

WALL PARTITION-Providing and fixing partition upto ceiling height

consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling

channel 50mm wide having equal flanges of 25 mm and 0.50 mm thick,

fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48 mm wide

having one flange of 34 mm and other flange 36 mm and 0.50 mm thick

fixed vertically within flanges of floor and ceiling channel and placed at a

spacing of 610 mm centre to centre by 6 mm dia bolts and nuts,

including fixing of studs along both ends of partition fixed flush to wall with

suitable anchor fastener or metal screws with nylon plugs at spacing of

450 mm centre to centre, and fixing of boards to both side of frame work

by 25 mm long dry wall screws on studs, floor and ceiling channels at the

spacing of 300 mm centre to centre. The boards are to be fixed to the

frame work with joints staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm

each) to be provided at the horizontal joints of two boards, fixed to the

studs using metal to metal flat head screws, including jointing and

finishing to a flush finish with recommended jointing compound, jointing

tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as

per manufacture's specification and direction of engineer in charge all

complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Both side 12 mm thick HDHMR board to IS: 5509 SQM 3,850.00 280.00 10,78,000.00

Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt/ suede finish with high density protective

1.3 9.127 surface layer and reverse side of adhesive bonding quality conforming to - -

IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing 12mm thick frameless toughened glass

door shutter of approved brand and manufacture, including providing

and fixing top & bottom pivot & double acting hydraulic floor spring type

fixing arrangement and making necessary holes etc. for fixing required

1.4 21.18 door fittings, all complete as per direction of Engineer in charge (Door sqm 4,540.70 90.00 4,08,663.00

handle, lock and stopper etc. to be paid separately)

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or

1.5 9.1 with dash fasteners of required dia & length (hold fast lugs or dash - -

fastener shall be paid for separately).

9.1.1 Second class teak wood cum 1,31,576.95 1.00 1,31,576.95

INSULATION- Providing and fixing thermal insulation with Resin Bonded

rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm

1.6 12.62 thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, SQM 277.90 142.00 39,461.80

rawel plug & washers and held and in position by criss cossing GI wire etc.

complete as per directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202

(Part I) non-decorative type, core of block board construction with frame

of 1st class hard wood and well matched commercial 3 ply veneering

with vertical grains or cross bands and face veneers on both faces of

35 mm thick including ISI marked Stainless Steel butt hinges with necessary

Providing and fixing aluminium extruded section body tubular type

universal HS 3000 Slimline Concealed Door Closer (having brand logo with

ISi, IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and

1.80 MR door widthfrom 701 mm to 1000 mm), with double speed adjustment with each 7,200.02 4.00 28,800.10

necessary accessories and screws etc. complete

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI

1.90 9.97 marked, anodised (anodic AC 10 as per IS : 1868 ), transparent or dyed to - -

required colour or shade, complete:

DOOR STOPPER:- Providing and fixing bright finished brass hanging type

floor door stopper with necessary screws, etc. complete.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular

Handle TH 123 with Roses & Escutcheon in SS packaged with Mortice

1.11 MR lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all EACH 3,250.01 4.00 13,000.04

Providing and fixing 600 mmx25 mm H Type handle for Doors approved

make and designs as per engineer in charge

Providing and fixing minimium 100 kg capacity flooor spring for Doors

approved make and designs as per engineer in charge

Providing and fixing Glass door lock approved make and designs as per

engineer in charge

2.00 CEILING - -

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

Providing and fixing false ceiling at all height including providing and

fixing of frame work made of special sections, power pressed from M.S.

sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide

x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to

centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required

size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre

to centre, shall be fixed in a direction perpendicular to G.I. intermediate

channel with connecting clips made out of 2.64 mm dia x 230 mm long

G.I. wire at every junction, including fixing perimeter channels 0.5 mm

thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter

of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm

centre, with 25mm long dry wall screws @ 230 mm interval, including fixing

of gypsum board to ceiling section and perimeter channel with the help

of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing

and finishing to a flush finish of tapered and square edges of the board

with recommended jointing compound , jointing tapes , finishing with

jointing compound in 3 layers covering upto 150 mm on both sides of joint

and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light

fittings, grills, diffusers, cutouts made with frame of perimeter channels

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-

12.45.1 (Part I) :2011 (Board with BIS certification marks) sqm 1145.95 Sqm 1,145.95 300.00 3,43,785.00

Providing and fixing mineral fiber false ceiling With 16 mm thick beveled

tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6 tile m 595x595

2.20 MR moisture resistance frame made glavinised silhoute section as per Sqm 3,250.00 150.00

approved make direction of engineer in-charge

CEILING PELMETS :- Providing and fixed pelmet of overall size

150mmx150mm and made hardwood framings hung from ceiling

2.3 MR @1000mm centre to centre with 1 nos of 12mm thk. fire retardant ply on RMT 960.00 31.41 30,150.10

vertical & 12mm thk. Commercial ply on horizontal surface (straight &

curved). Inclusive of finishing in Paint.

Providing the gypsum double sided cove of 150mm x 150mm having a

2.4 MR facia of 75mm to macth the specifications same as above RMT 675.00 62.00 41,850.14

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round

the mineral fibre/ gypsum ceiling. In order to make the Mineral Fiber/

2.5 MR gypsum ceiling higher than the Gypsum Ceiling by upto 100mm as per RMT 395.00 92.00 36,340.12

drawings. (visible surface of gypsum band to not exceed 100mm)

including plastic emulsion paint.

3.0 FINISHING WORKS - -

Providing and applying plaster of paris putty of 2 mm thickness over

3.1 13.26 plastered surface to prepare the surface even and smooth complete. sqm 214.30 990.00 2,12,157.00

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50 grams/

3.2 13.83 litre of approved brand and manufacture, including applying additional - -

coats wherever required to achieve even shade and colour.

Applying priming coats with primer of approved brand and manufacture,

3.3 13.85 having low VOC (Volatile Organic Compound ) content. - -

With ready mixed pink or grey primer on wood work (hard and soft wood)

having VOC content less than 50 grams/ litre

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved make,

in all colours, shades except burgundy, bottle green, black of any size as

approved by Engineer-in-Charge, in skirting, risers of steps and dados,

3.4 8.31 over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) Sqm 1,063.45 50.00 53,172.50

and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in

white cement mixed with pigment of matching shade complete.

Providing and fixing wall paneling and partition frame work made of

3.50 MR 25x50 mm aluminium section 600x600mm c/c distance as per approved SQM 834.76 250.00 2,08,690.50

4.0 MISCELLANEOUS WORKS - -

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

BLINDS Providing & supplying of Window Blinds as per the approved

sample in required shade and style consisting, of ZEBRA BLINDS comprising

of optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric

weight 460-480G weight per sq m, Thickness 0.67 mm, Yarn count 18-

19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-

5659-2 .Thetear resistance should be complying to ISO4674 & breaking

resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and

safe installation, moulded plastic with steel spring support and inserted

into the tube end. It shall be driven by a ball chain pulley with ball chain

and can be positioned at right side or left hand side of the Shade. The

Shade when lowering or raising, shall be automatically locked in position

upon release of the ball chain by means of a built in friction lock.Universal

clutch for left and right hand operation.Chain Gear Ratio of 1.75:1. The

END PLUG shall be molded of plastic witha steel location pin.The plug

shall be inserted into the tube end.(Opposite to the Drive Unit) for ease of

installation. The SUPPORT BRACKETS shall be of coated steel & provided

with covers and used in right hand or left hand positions differentiated by

the acceptance of the of the rectangular drive unit support or the round

idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame

(d) in Recess. The Bracket should be protruding outside maximum of

80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal

diameter & skin thickness of 1mm and shall incorporate a key way integral

with the tube to accommodate the spline. The BOTTOM RAIL shall be a

Flat Bottom made up of powder coated steel. The BALL CHAIN shall be

2mm diameter cord with 4.5mm diameter acetal balls moulded co-axially

to it on 6mm pitch to form an endless ball chain. It is used for raising or

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass

surface as approval of the Architect. (Only film surface area shall be

measured and paid).

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm

Laminate of matching, Shutters to be fixed to a frame. Rigidly fixed on

both sides and top finshed in laminate. No internal carcass required. All

Hinges of hettich or equivalent. Internal Surface of the shutter in balancing

4.3 MR white laminate. All shutters to be provided with Stainless steel louvers at SQM 14,342.05 2.00 28,684.10

the top and bottom of the shutter as per the site requirements and

instrcution of the Engineer In charge.

Providing & fixing imported decorative Poly décor fabric Wall Paper

(on walls and ceiling) of weight 475 g /sqm as per approved shade &

design including prepration of surface with 2 coats of Nubin Glue based

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

Providing and fixing of 4,6 mm thick annealed GRIHA rated lacquered

glass manufactured industrially by curtain coating process with PU

lacquer (50 micron thick), opaque (if viewed against a support wall)

conforming to EN 16477 standards for back painted glass , of approved

color by Architect/ Client fixed with compatible Silicone having Shear

Bond Strength (Dry, 24 hours), greater than 450 kpa and tack free time of

10 to 30 mins compatible for installation of mirror and lacquered glass /

Foam based double sided adhesive tape for instantaneous adhesion,

compatible with mirror and lacquered glass having Shear bond strength

(Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water

proof marine plywood / MDF / Mineral fibre board which is mounted on

the RCC wall/any other structure. The contractor should submit test reports

for backpainted glass from manufacturer - High humidity Resistance

(conforms to BS EN 1036 1999); Color fastness ISO 105B02 standard &

Mechanical Resistance ISO 7784 ( Taber Abrasion test ) ISO 2409 ( Cross

Hatch Test ) standard The manufactured backpainted glass should be

environmentally friendly (no lead, no arsenic, no copper,

noformaldehyde); appropriate recycled content (12% post industrial / 6%

post consumer); compressive strenght (1000 MPa) & tensile strenght (40

MPa),same as float glass

Providing and fixing Aluminium Skirting 100 mm ht - Groove skirting -

4.6 MR Natural Anodized Finish (Make- as per make list or equivalent) RMT 811.00 175.00 1,41,925.48

Providing and Fixing Logo & Signage in 3D ,as per the approved Design/

pattern with Mat /Gloss Finish Brass Letters with Mettalic/ Acrylic Base,

4.7 MR complete as required at site with the direction of the Enginner In Charge sq inch 4,250.00 10.00 42500.00

Providing and Fixing of floor tiles with wear layer is of 0.5mm, made upof

Stone Polymer composite, 100% Water & Termite proof, Scratch/ Flame/

UV resistant, anti-microbial, 100% recyclable Green product having click

3.2 MR system with suitable skirting. Classification of abrasion resistance (Abrasion SQM 4,250.00 150.00 6,37,500.00

wheelfromH-18 Calibrade, loadApplied 1000 grams, No. of Cycles 14,400).

" ( Along with Matching Profiles)

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

Providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber

or equivalent of approved make with 100% Nylon and completely water

proof resilient backing. The flooring should be Anti static with thickness of

4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet

should be completely stain resistant and of a density approx. 80 million

fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering

should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-

3.3 NS 8, Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial sqm 4,880.00 100.00 4,88,000.00

treatment, with resilient waterproof backing, anti allergic which is certified

by British allergy foundation, with ten year replacement guarantee. The

carpet should have permanent static control & should be fixed with

powder coated aluminum angles as per detail. Aluminum angles to be

paid separately.

Digitally signed by AMIT

Electrical/FA/PA

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

1.0 DISTRIBUTION BOARDS.

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker (RCCB),

1.4 having a sensitivity current 30 mA in the existing MCB DB - -

complete with connections, testing and commissioning etc. as

2.0 CABELS / MAINS - -

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supply ,laying,testing and commissoning of 1100V grade

armoured cable having sector / circular shaped aluminium /

copper conductor PVC insulated cores under ground PVC tape

wrapped inner sheathed, GI strip / wire armoured and overall - -

extruded PVC sheathed confirming to IS: 1554, laid on wall or

ceiling using GI clamps and spacers as per route shown at site

and further as directed by Engineer-in charge

2.1 MR 16 Sq.mm 4 core copper cable mtr. 825.00 50.00 41,250.00

2.1 MR 25 Sq.mm 4 core copper cable mtr. 1,450.00 50.00 72,500.00

4.0 WIRING - -

Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor single core

cable in surface / recessed medium class PVC conduit, with

4.1 1.10 modular switch, modular plate, suitable GI box and earthing the - -

point with 1.5 sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required.

a 1.10.3 One light point controlled by one 6A switch Per Pts 1,467.00 50.00 73,350.00

Wiring for group controlled (looped) light point/fan point/exhaust

fan point/ call bell point (without independent switch etc.) with

1.5 sq. mm FRLS PVC insulated copper

4.2 1.54 conductor single core cable in surface/ recessed steel conduit, - -

and earthing the point with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed steel conduit as required.

a 1.7.1 2x1.5sqmm+1x1.5sqmmearth wire Per mtr. 327.00 500.00 1,63,500.00

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for twin control point wiring using 1.5 sqmm copper

conductor FRLS PVC insulated copper conductor cable drawn

through 25 dia MS conduit laid in surface/concealed over false

4.4 1.4 ceiling or in slab/wall chases including ,2way modular Per Pts 1,981.00 20.00 39,620.00

switches,modular plate ,suitable GI box and earthing the point

with 1.5 sqm FRLS PVC insulated copper conductor single core

cable as required

Supplying and fixing following modular switch/ socket on the

4.5 1.24 existing modular plate & switch box including connections but - -

excluding modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 122.00 70.00 8,540.00

d 1.24.5 6 pin 15/16 A socket outlet Each 197.00 90.00 17,730.00

Supplying and fixing following size/ modules, GI box alongwith

4.6 1.27 modular base & cover plate for modular switches in recess etc. as - -

Supplying and fixing following Modular base & cover plate on

existing modular metal boxes etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm

solid copper conductor PE insulated, shielded with fine tinned

copper braid and protected with PVC sheath in the existing

surface/ recessed steel/ PVC conduit as required.

Supplying and laying HDMI Cable with connector on both ends

upto 15m length or as per site requirement

5 LIGHTING FIXTURES - -

LINEAR LIGHT 28-36W as per the specifications and direction of

Engineer In-charge

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supply, Installation, Testing and Commisioning of pre-wired round

shape Surface Mount 15Watt LED Down Lighter fitting complete

with all accessories, housing made of Aluminium Die-cast, System

Efficasy >100 LPW, CRI >80, CCT of 4000K. suitable for 220 V, 50 Hz,

The luminare rated life (L70) >50000 Hours with High efficiency

5.2 MR driver with inbuild surge protection, over voltage protection, short NOS 1,470.91 80.00 1,17,672.46

circuit protection and operating at >0.95 PF., BIS approved Driver

including connection with 1.5 sq. mm FR PVC insulated, copper

conductor, single core cable and earthing etc as required.

Supply, Installation, Testing and Commisioning of 600X600 36-

40Watt LED fitting complete with all accessories, housing made

of Aluminium Die-cast, System Efficasy >100 LPW, CRI >80, CCT of

4000K. suitable for 220 V, 50 Hz, The luminare rated life (L70) >50000

5.5 MR Hours with High efficiency driver with inbuild surge protection, NOS 3,250.00 40.00 1,30,000.00

over voltage protection, short circuit protection and operating at

>0.95 PF., BIS approved Driver including connection with 1.5 sq.

mm FR PVC insulated, copper conductor, single core cable and

earthing etc as required.

6 WIRING FOR DATA AND VOICE OUTLETS - -

Supply and fixing the following sizes of PVC medium duty ISI

marked conduits (IS : 9537 Part-III) complete with accessories

6.1 such as bends, junction boxes, pull boxes etc., in recess or on - -

surface including cutting chases in the walls/floors and making

good the same complete as required.

Supplying and drawing of CAT 6A U/UTP cable, white jacket, 4 pair

6.2 1.53 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as - -

Supply & fixing of Plug in type information outlet (campatible with

6.3 MR data cables) in existing faceplate/ GI Box in wall/furniture/floor Nos. 582.51 60.00 34,950.56

complete as required.

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supplying and fixing following modular switch/ socket on the

6.4 1.24 existing modular plate & switch box including connections but - -

excluding modular plate etc. as required.

1.24.6 Telephone socket outlet Each 148.00 40.00 5,920.00

Supply and fixing of the following types Face Plates complete

with all accessories.

Supply & Fixing of Dual Faceplate, Duplex Port (for data and for

voice) or as required square plate having spring shuttered front

a. MR access for preventing ingress of dust, dimension as per Nos. 90.04 40.00 3,601.58

commercially available modular office furniture.

Supply ,laying ,installing , testing and commmissioning of the 50

pair multi core 0.61 mm annealed copper conductor PVC

insulated and PVC sheathed armoured telephone cables

6.6 MR generally conforming to ITD S/WS-11-C and IS 1554 part I direct in mtr. 457.57 50.00 22,878.28

ground /surface and / or in existing pipe as required and includig

making terminal joints, complete as required.

Supplying, installing, testing and commissioning of 24 port Cat 6A

patch panels available with block of four equipped with tool less

6.7 MR IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6A EACH 16,491.19 2.00 32,982.39

U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6

X RJ 45 Tool less connector U/UTP unit in a block.

7 CABLE TRAY.& RACE WAY. - -

4.1 upplying and installing following size of perforated painted

with powder coating M.S. cable trays with perforation not more

than 17.5%, in convenient sections, joined with connectors,

7.1 suspended from the ceiling with M.S. suspenders including bolts - -

& nuts, painting suspenders etc as required.

GI Raceway & Junction boxes ( Raceway on floor shall be of

aluminium only)

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

MR Providing and fixing 2 mm thick steel sheet factory fabricated

post galvanized raceway with internal partition/compartmentized

of the following sizes including providing removable 3 mm thick GI

cover, knock out holes and fixing accessories earthing with 8 SWG

copper earth wire complete as required including floor supports, - -

bends, access boxes, tap off boxes and cross over as per

specification and site requirement. (overhead / wall mounted

recovery & function boxes shall be 1.6 mm thick)

c) MR 150 mm wide x 38 mm deep raceway or as per site RM 1,603.10 10.00 16,031.00

d) MR 100 mm wide x 38 mm deep raceway or as per site RM 1,250.00 10.00 12,500.00

MR Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet

7.4 junction box including providing 3 mm thick stainless steel cover Nos. 1,874.51 5.00 9,372.54

as per specification.

A. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : - -

Supplying, installation, testing & commissioning of intelligent Pcs

1 17.2.4 analog addressable photothermal detector complete with 2858.00 20.00 57,160.00

mounting base complete as required.

Supplying, installation, testing & commissioning of addressable Pcs

manual call point complete as required.

Supplying, installation, testing & commissioning of addressable Pcs

horn cum strobe complete as required.

Supplying, installation, testing & commissioning of fault isolator Pcs

complete with base as required.

Supplying, installation, testing & commissioning of response Pcs

indicator on surface/recessed MS Box having two LED, metallic

cover complete with all connections etc as required.

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm panel,

central processing unit with the following loop modules and

capable of supporting not less than 240 devices (including

detectors) and minimum 120 detectors per loop and loop length

up to 2 km, network communication card, minimum 320

character graphics/ LCD display with touch screen or other

keypad and minimum 4000 events history log in the non volatile

6 17.2.1 memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs - -

back-up with 24 volt sealed maintenance free batteries with

automatic charger. The panel shall have facility to connect

printer to printout log and facility to have seamless integration

with analog/digital voice evacuation system (which is part of the

schedule of work under SH: PA System) and shall be complete

with all accessories . The panel shall be compatible for IBMS

system with open protocol BACnet/ Modbus over IP complete as

B CABLES & ACCESSORIES FOR FAS : - -

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, RM

600/1000V rated with annealed copper conductor having

6 17.5.2 XLPE insulation, steel wire armouring & FRLS outer sheath 173.00 200.00 34,600.00

complete as required.

C SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES : - -

Supplying, installation, testing & commissioning of Pcs

7 17.3.4 ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS 2428.00 10.00 24,280.00

enclosure complete as required.

D CABLE & ACCESSORIES FOR PA SYSTEM - -

Supplying and drawing of cable Fire Retardant PVC insulated

copper conductor cable in the existing surface / recessed

17.5.3 steel conduit of following pairs, cores and size including - -

connections and interconnections etc. as required..

8 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm RM 54.00 500.00 27,000.00

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supplying, installation, testing & commissioning of digital Each

9 17.3.6 audio amplifier 50 Watt, 25V rms operating at 240 volt AC 96779.00 1.00 96,779.00

supply complete as required.

SUB HEAD (H) : UPS SYSTEM - -

Supplying, installation, testing and commissioning of (N+1) 20

kVA/27KW online double conversion fully microprocessor based

,indoor type, compact UPS system of mentioned rating with

designed output PF .9 at 40 degree and IGBT based PWM

technology to achieve THD < 5% and input power factor of

greater than 0.95 at 50% loading, Efficiency >= 93% at 50 % load,

13 MR suitable for three phase AC input voltage 320 V to 480 V, 50 Hz - -

+3% / - 3 % and three phase AC output voltage 415 ± 1% volts &

frequency 50 ± 0.5 Hz with all components as mentioned in BOQ,

specifications and schedule, complete as required and as per

technical specification. Each unit shall be comprising of the

following: Total 2 no.s (In parallel)

125% rated Rectifier cum charger unit +100% rated Invertor,

Integrated in UPS module

100% rated Inbuilt static switch at the invertor output + 2 Nos. - -

100% rated Inbuilt static switches at the static bypass line.

100% rated Inbuilt Maintenance Bypass. - -

Web-enabled Monitoring and Management through SNMP

protocols for multi-OS environments.

Inbuilt feature required for input phase seq protection and

automatic change. UPS should work on mains and should not go

to battery mode in case of input phase sequence change

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supplying, unloading, installing testing and commissioning of

necessary VRLA batteries of suitable size having 15 minutes back

up time to 30KVA UPS for full load (75Ah Batteries X 20 No.) to be

provided. 1 No spare batteryof same AH to be provided and cost

to be added. Total VAH = 18000VAH - -

Note : Concerning vendor needs to furnish the battery sizing

calculations at the time of GA approval and battery size has to

be as per the approved GA drawing.

Supply, unloading, installation testing & commissioning of

matching cabinet/open racks to house above mentioned

batteries for 30 KVA UPS system along with suitable size - -

interconnecting cable (for UPS to Battery and battery to battery),

MCCB etc. complete as required & as per specifications.

Supply,installation testing and commissioning of UPS monitoring

software suitable for RJ-45 communication and capable of giving

pop up messages for all alarms received from UPS. All shall be

capable of the following:-

Giving notifications like e-mail, paging notification, broadcast

notification, battery replacement notification, run event-based - -

Event logging, data logging and action logging (with date, time,

description of fault and event).

Run the battery diagnostic test. - -

Automated unattended shutdown of computers. - -

Local notification through audible alarm. - -

Software should support :

latest version of Microsoft Windows/ Server, AIX, HP-UX, Sun Solaris, Set 623660.01 1.00 6,23,660.01

Linux, Novell Netware, MAC

Total DSR & Total Non DSR 22,66,887.00 11,82,594.70

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

Supply Installation, Testing & Commissioning of modular type Variable

Refrigerant Flow/ Variable Refrigerant Volume air cooled Outdoor

units suitable for cooling and heating, having all hermetically sealed

inverter type Scroll Compressor(s), minimum two compressors for

above 14 HP modules, microprocessor based Controller, top

discharge type condensing unit(s), with R410A Refrigerant, vibration

1.0 1.1 isolators, with suitable foundation etc. complete as required.The unit Per HP 16415 36.00 5,90,940.00

shall deliver the rated capacity at AHRI Conditions and work even at

50°C ambient temperature without tripping.The unit shall be suitable

to work on 400V+/-10%, 3 Phase, 50Hz AC power supply.The unit shall

be filled with first charge of the refrigerant and ready for use as

required.The COP at AHRI conditions shall not be less than 3.1 and

IEER not less than 6.5 .

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following minimum

capacity 4-wayflow VRV/ VRF Cassette Type Indoor ceiling mounted

unit equipped with synthetic washable media pre-filter, fan section

with low noise fan/ dynamically balanced blower, multi speed motor,

coil section with DX Copper coil, electronic expansion valve, outer

cabinet, drain pump, grill, necessary supports, vibration isolation,

cordless remote control etc., suitable for operation on single phase

230V±10%, 50 HzAC supply, complete, as required. The unit shall have

automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will be at

air inl et conditions of 27 Degree CD Band 19 Degree CWB

4-Way Cassette type - -

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

3.0 REFRIGERANT PIPING - -

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system,

DSR 2019 complete with fittings, with suitable adjustable ring type hanger

3.0 VRF/VRV supports, jointing/brazing including accessories, insulated with XPLE - -

Item No 5 Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as given

below for Suction and Liquid lines, all accessories as per

specifications etc. as required :

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

19.2 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick

4 CONDENSATE DRAIN UPVC PIPE - -

Supply, installation, testing and commissioning of uPVC Pipe ,complete with

fittings, supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and - -

accessories as per specifications, drawings.

4.3 MR Imported fittings Y-joints and headers etc. Nos 4281.4 20.00 85,628.16

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper

in suitable conduits between indoor and outdoor unit.

MR Supply and fixing IP-55 based outdoor MCB box with 1 NOS 65 amp RCCB Nos 14650.0 2.00 29,300.00

Supply and fixing MS base frame for VRV outdoor stand as per approved size

Digitally signed by AMIT

Sr. No. Item Description Unit Rate Qty Amount

1 Supply, Installation, Testing & Commissioning of 24 PORT Managed Network Switch Unit 52,650.00 2.00 1,05,300.00

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265 Vandal Proof Dome camera with

2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR distance,Up to 120 dB WDR (Wide Dynamic

Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple

streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video

Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Crossing line, Motion

detection, Object left, Missing object,Intelligent Identification Face detection, Defocus, Scene

Change,PoE (IEEE802.3 af) Power consumption: Max 7.2W,Edge Storage Micro SD Card, Up to

256GB, ANR Support,Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-

condensing),Compatible Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing and Commissioning of 48Ch Embedded Network Video Recorder with

2 4 Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA, RAID, Redundant power supply, Smart Nos 2,15,650.00 1 2,15,650.00

Analytics and ONVIF

SITC of SSD Hard Disk Drive 8TB, 24/7 surveillance category Only complete etc as required.etc.all

C. 200 Pair MDF Box -

1 200 Pair MDF Box with mounting Frame Nos. 32,500.00 1 32,500.00

Digitally signed by AMIT

Sno. Item Specifications Rate Qty Amount

GM Table Supplying and placing in position of main table as per photograph/drawing .The table shall

be made out of 25mm thick pre -laminated particle board of approved shade. The working

and non working edges shall be finished with machine pressed with 2mm PVC egdge

banding. The table top shall be supported with MS powder coated "C" shape leg of size

50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of

18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table shall be

provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage

1 having a provision for three equal drawer unit and two openable shutter & one open 78,500 1.00 78,500.00

storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle

board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or

as per site requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall

Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

GM High Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size

Back Chair :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design

contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and

back) upholstered with leatheritte and cut foam. The chrome plated loop armrest with

2 padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic 26,600 1.00 26,600.00

height adjustment which shall have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/-

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

GM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X

Back Chair (D)505mm X (H)990mm.A contemporary design with an all black finish, . Material &

subtype:Premium Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X

(D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever,

3 Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot pressed plywood 19,600 3.00 58,800.00

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Sno. Item Specifications Rate Qty Amount

DGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall

be made out of 25mm thick pre -laminated particle board of approved shade. The working

and non working edges shall be finished with machine pressed with 2mm PVC egdge

banding. The table top shall be supported with MS powder coated "C" shape leg of size

4 50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of 65,650 2.00 1,31,300.00

18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table shall be

provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage

having a provision for three equal drawer unit and two openable shutter & one open

DGM High storage with

Supplying andshelf in it. The

placing Side unit

in position of top

360 shall be made

degrees out of

revolving 18mm

chair laminated

. The chair of Size

Back Chair :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design

contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and

back) upholstered with leatheritte and cut foam. The chrome plated loop armrest with

5 padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic 24,650 2.00 49,300.00

height adjustment which shall have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/-

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

DGM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X

Back Chair (D)505mm X (H)990mm.A contemporary design with an all black finish, . Material &

subtype:Premium Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X

(D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever,

6 Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot pressed plywood 19,600 6.00 1,17,600.00

upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

The backrest has a foam of 28kg/m3.

2 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to

the soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour &

Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech

solid wood have used for framing construction of sofa .The seat cushion is made of multi

7 layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 42,500 3.00 1,27,500.00

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch

strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2

seater Dimension(L)1390mm X (D)750mm X (H)710mm

Digitally signed by AMIT

Sno. Item Specifications Rate Qty Amount

Single seater Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to

sofa the soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour &

Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech

solid wood have used for framing construction of sofa .The seat cushion is made of multi

8 layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 24,650 2.00 49,300.00

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch

strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2

seater Dimension(L)1390mm X (D)750mm X (H)710mm

3 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to

the soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour &

Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech

solid wood have used for framing construction of sofa .The seat cushion is made of multi

9 layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 52,480 1.00 52,480.00

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch

strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2

seater Dimension(L)1390mm X (D)750mm X (H)710mm

AGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall

be made out of 25mm thick pre -laminated particle board of approved shade. The working

and non working edges shall be finished with machine pressed with 2mm PVC egdge

banding. The table top shall be supported with MS powder coated "C" shape leg of size

50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of

18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table shall be

provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage

10 having a provision for three equal drawer unit and two openable shutter & one open 55,650 5.00 2,78,250.00

storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle

board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or

as per site requirement. Main Table Dimension (L)1800mm X (D) 900mm X (H)750mm overall

Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

Digitally signed by AMIT

Sno. Item Specifications Rate Qty Amount

AGM and PS Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L)

High Back x 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof

Chair plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR

plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The

chair shall be provided with self tension single locking mechanism and pneumatic height

adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height

adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension

force.The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC

with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a

foam of 28kg/m3. adjustable arm rest and head rest

PS Table Supplying and placing in position of main table as per photograph/drawing .The table shall

be made out of 25mm thick pre -laminated particle board of approved shade. The working

and non working edges shall be finished with machine pressed with 2mm PVC egdge

banding. The table top shall be supported with MS powder coated "C" shape leg of size

50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of

18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table shall be

provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage

12 having a provision for three equal drawer unit and two openable shutter & one open 42,500 1.00 42,500.00

storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle

board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or

as per site requirement. Main Table Dimension (L)1500mm X (D) 900mm X (H)750mm overall

Side Runer Dimension (L)1200mm X (D) 450mm X (H) 675mm

Conference Supplying and placing in position of conference table of required size as per image/drawing.

Table The work surface top should be of thickness 42mm top prelaminated particle board with

2mm thick PVC edge banding. The side panel are made up of 36mm thick prelaminated

particle & modesty panel are made out of 25mm thick prelaminated particle board with

13 2mm thick PVC edge banding. The wire carrier should be made from 0.6mm thick CRCA & 95,000 1.00 95,000.00

powder coated 40-50 microns. Also having a provision of 6 module flip top box & metal

raceway for wire flow.

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze

chair chair of Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be

ergonomically design contour lumbar back design made of 12mm thick BWR plywood (IS

Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The chair shall be

14 provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 16,500 66.00 10,89,000.00

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-

2kg /m3) The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Sno. Item Specifications Rate Qty Amount

Modular Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With

Workstation Side Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm

Partition Ht. 1200mm, Double Raceway systems Skirting label and below the table top . lower

tile both side laminated and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end

15 18mm thick MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 32,650 14.00 4,57,100.00

725H made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White,

Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-

Munshel Gray. and White Tinted Glass

Linear Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

Workstation workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2

mm thk PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm

Slanted Leg and 50mm x 25mm Horizontal connectors with Powder coting of 50

Micron.Middle Leg :- 0.8 mm thk Metal panel fixed on both side of the "T" leg for Vertical wire

carrying purpose.(Sharing Workstation). 0.8 mm thk Single/Double metal powder coated

raceway with Powder coting of 50 Micron below top for wiring.Vertical wire carrying pole with

powder coating 50 micron below top for wiring( Non- sharing workstation ). Also having a

provision of ms perfoated sheet hanging modesty. provision of glass divider rest on the "D"

16 brackets on the table top between opposite seatings. All working or non working edges shall 26,650 9.00 2,39,850.00

be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of

2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick

prelaminated Particle board with provision of handles & Locking arrangement

Pantry Table Providing & Installation of Pantry table of size 1.8m x 0.75m x 1.05m (ht) made out of 19mm

thk. Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as

17 per design. The Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS 24,345 3.00 73,035.00

pegs to be provided above table. One (1) number Drawer pedestal with 3 drawers to be

provided under the table.

Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC

19 TABLE CENTRE TABLE WITH GLASS TOP 16,500.00 1.00 16,500.00

20 TABLE SIDE TABLE WITH WOODEN STRUCTURE 12,500.00 3.00 37,500.00

Digitally signed by AMIT

Sno. Item Specifications Rate Qty Amount

Openable The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back

Shutter panel is made of 09mm thick MDF of approved shade. All the edges of storage surface shall

21 storage be provided with machine pressed imported PVC lipping glued with hot melt EVA glue free -

from any VOC with free groove handle and suitable lock. All exposed area PVC edge lipping

Total Amount 37,71,995.00

Total Amount 37,71,995.00

Digitally signed by AMIT