PETTY REPAIRS OF DAY TO DAY MAINTENANCE OF OTM ACCN AT AGE B/R I UNDER GE (AF) TECH AREA AT AF STATION AGRA

Amount

S&F in repair existing plastic syphon for low level PVC flushing cistern of 10 Litre capacity complete all as specified and directed.

Labour only for adjustment of the float valve or ball valve or lever or handle without replacement of any part of the high level cistern & OHT of any size complete all as specified and directed.

S&F in repair float valve of PTMT with polythelene ball of 15mm dia pipe complete all as specified and directed.

S&F in repair float valve of PTMT with polythelene ball for 20mm dia pipe complete all as specified and directed.

S&F in repair polythelene ball of existing 15mm/20mm dia float valve complete all as specified and directed.

S&F in repair 45 cm long 15 mm size PVC connection with 02 Nos PTMT nut and rubber washers complete all as specified and directed.

M&L in repair of water leakage in bib tap, pillar tap, stop cock, angle valve, WHB mixture, wall mixture, concealed etc of any description & any size by changing washer/ jumper wall etc complete all as specified and directed. Note:- (i) One Plumber will be detailed by the contractor for attending above complaints on daily basis. Cost of which shall be deemed to be included in quoted rates. (ii) The Plumber so detailed by the contractor will report to MES complaint cell at 0845 hrs morning to receive complaint slip from department (for all types of plumbing complaints) from MES complaint cell and after rectification hand over the rectified complaints copy to the complain cell on daily basis. (iii) The complaints shall be rectified within 08 Hours. If contractor fails to detail above tradesmen a panel recovery@ Rs. 1000.00 per day shall be made to contractor and shall be recovered from RAR/Final bill.

M&L in replacement of brass spindle of existing 15mm dia bore bib cock/ stop cock/ angle valve/ C P Pillar cock/ Wash basin mixture and wall mixture of any description complete all as specified and directed.

S&F in repair pillar tap 15mm bore dia cast copper alloy with capston chromim plated screwed down high pressure with or without lettered "Hot" or "Cold" with long screwed shanks and fly buts screwed for iron pipe complete all as specified and directed.

S&F in repair PTMT standard bib tap of 15mm dia pipe any colour high pressure, screwed for iron pipe and fixed (minimum weight 15 mm-90 gms) complete all as specified and directed.

S&F in repair long body bib taps 15 mm bore (for iron pipe) cast copper alloy fancy type chormium plated with clutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair for angle stop valves 15 mm bore (for iron pipe) fancy type chromium plated screwed down high pressure with butterfly handle, screwed both ends complete all as specified and directed.

S&F in repair Health Faucet with 1.5 Meter long SS tube and hook complete all as specified and directed.

S&F in repair Bathroom Looking Mirror size of (600x450mm) complete all as specified and directed.

S&F in repair 15 mm bore dia gun metal globe or gate valve with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

S&F in repair two way Angle cock with flange 15mm bore (for iron pipe) cast copper alloy fancy type chromium plated screwed down, complete all as specified and as directed.

S&F in repair CP soap dish fixed to plug with CP brass screws complete all as specified and directed.

Taking down the existing bottle traps of wash hand basin and refixing the same after cleaning including replacement of washers, packing etc. if required complete all as specified and directed.

S&F in repair brass chromium plated bottle trap of 32 mm bore for wash hand basin with inlet and outlet and screwed for pipe including necessary packing, union complete all as specified and directed.

M&L in replacement of existing chromium plated brass waste coupling for wash hand basin of size 32 mm dia complete all as specified and directed.

M&L in replacement of existing chromium plated brass waste coupling for sink of size 40 mm dia complete all as specified and directed.

M&L in replacement of chromium plated grating of size 125 mm dia (with hole or without hole) complete for Nahani/Floor traps complete all as specified and directed.

M&L in replacement of PVC waste pipe 32 mm bore with PVC coupling for wash hand basin complete all as specified and directed.

Repair to low level flushing cisten of any size/description by rectifying water leakage by adjusting/replacing the washer and adjustment of lever require for making the cistern functional complete all as specified and directed.

Removal of air lock/blockage of water in GI Tubing 15/20mm bore including taking down (if required) cleaning the pipe or fitting etc and refixing the same in position complete including new GI fitting if required for refixing complete all as specified and directed.

Draining out water from existing PVC water storage tank exc 500 Litre but not exc 1000 Litre capacity and cleaning silt deposited therein, washing out with soap water or surf including taking down connection and refixing the same with new fittings if required complete all as specified and directed.

Draining out water from existing PVC water storage tank exc 250 ltr but not exc 500 ltr capacity and cleaning silt deposited therein, washing out with soap water or surf including taking down connection and refixing the same with new fittings if required complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to wall including flat iron clamp for proper fixing complete all as specified and directed.

S&F in repairs PVC (SWR) bends 110 mm dia of any radius complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 160 mm bore single socketed in any length with rubber ring joints fixed to wall including flat iron clamp for proper fixing complete all as specified and directed.

S&F in repairs PVC (SWR) bends 160 mm dia of any radius complete all as specified and directed.

S&F in repair 15 mm bore GI tubing of medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including cutting grooves and making good in CM (1:3) or PCC (1:2:4) Type B0 for concealed tubing complete all as specified and directed.

S&F in repair 20 mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including cutting grooves and making good in CM (1:3) or PCC (1:2:4) Type B0 for concealed tubing complete all as specified and directed.

S&F in repair vitreous China squatting pan 'orrisa' pattern (white colour) of size 580x440mm with integral foot rests including provision of lime concrete bedding and P trap complete all as specified and directed.

S&F in repair for vitreous china wash basin (white) and flat back size 550x400 mm including cutting for and pinning in ends of brackets including fixing of 32 mm low density polylethylene pipes (LDPE) of pressure rating 6kg/cm2, cupling, PVC connection of 15 mm with PTMT nuts, brackets complete all as specified and directed.

S&F in repair vitreous china wash down water closet (pedestal pattern) of any colour including fixing of bolts complete all as specified and directed.

S&F in repair 10 Litre capacity PVC valveless syphonic action type low level flushing systern "dual flush" of white colour with inlet ball valve, float & handle including bracket complete all as specified and directed.

S&F in repair Three layered rotational moulded polyethylene water storage tank 500 Litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing all necessary fittings for connecting with pipe line, metal lockable cover complete all as specified and directed.

S&F in repair Three layered rotational moulded polyethylene water storage tank 1000 Litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including providing all necessary fittings for connecting with pipe line, metal lockable cover complete all as specified and directed.

S&F in repair plastic WC seat cover of any colour for pedestal pan, closed pattern with flat bottom & cover including MS chromium plated or aluminised hinging devices complete all as specified and directed.

M&L for brick work with fly ash bricks, straight of curved on plan exc 6M mean radius built in CM 1:6 complete incl demolition of existing brick work built in cement mortar complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement incl taking down cement plaster on concrete, brick surface and raking out hacking for key scrubbing down with water to receive plaster including two coat of exterior emulsion paint over a coat of primer after preparation of surfaces complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement incl taking down cement plaster on concrete, brick surface and raking out hacking for key scrubbing down with water to receive plaster including two coat of oil bound distemper over 1 mm thick wall care putty complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:3 on fair faces of ceiling surfaces finished even & smooth without using extra cement incl taking down cement plaster on concrete, brick surface and raking out hacking for key scrubbing down with water to receive plaster including three coat of white wash after preparataion of surface complete all as specified and directed.

S&F in repair PVC flush pipe of 32 mm dia for connecting low level flushing cisten inclulding jointing to WC complete all as specified and directed.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair ISI marked hydraulically regulated door closer aluminium (Die Cast) body type suitable for door shutter width upto 1000 mm and weight between 60 to 80 kg complete all as specified and directed.

S&F in repair double action floor spring hydraulically regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty complete all as specified and as directed.

Taking down existing UPVC doors/windows and re-fixing after tightening loose screws including replacement of unserviceable screws, PVC beading, rubber packing, rubber bushes etc with and including taking down carefully glass panels & re-fixing the same and other hardware fittings such as hinges, handles, door closers/floor springs etc complete all as specified and as directed.

S&F in repair UPVC door lock suitable for existing door as per manufacturer instructions etc complete all as specified and directed.

S&F in repair 300mm long, Brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and as directed.

S&F in repair 150mm long Brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F in repair 125mm extruded brass handles, fabricated type, polished complete all as specified and directed.

S&F in repair single legged floor door stopper 140mm long with rubber shoe complete all as specified and directed.

Easing of wooden door shutters/wooden window (One unit shall comprising of one window irrespective of number of leaf) for properly closing/opening tightening of hinges or changing the position of hinges and adjustment of tower bolts, sliding bolt etc complete all as specified and as directed.

Taking down cement plaster in patches on brick work, racking out joints, hacking for key scrubbing down with water etc complete and removing the spoil to a distance of n.exc 100m & depositing where directed & M&L for 15 mm thick cement plaster in CM (1:4) on brick work/concrete surface finished even & smooth without using extra cement, area of the patches should not be more than 2.0 sqm including two coat of colour wash after preparation of surface complete all as specified and directed.

S&F in repair 5 mm thick figured coloured glass, pin head type & fixed with existing aluminum beads, PVC packing of any type complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality for wooden/steel window and glazing with oil putty in squares or fixed with beads etc complete all as specified and as directed.

S&F in repair 5 mm thick sheet glass ordinary quality for wooden/steel window and glazing with oil putty in squares or fixed with beads in each pane n.exc 0.50 sqm complete all as specified and as directed.

S&F in repair MS Helical door spring including roller & roller plate complete all as specified and directed.

S&F in repair 5mm thick heat absorbing glass for glazing complete with beads fixed with brass screws complete all as specified and directed.

S&F in repair door seal aluminium plate with nylon brush ivory matt having width 6 cm colour ivory, matt finishing, incl screw for fixing etc complete all as specified and directed.

S&F in repair of corner glass shelf 12" complete all as specified and directed.

S&F in repair 12mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations for partition etc, complete all as specified and directed.

S&F in repair aluminium powder coated deco grill fixed with aluminium channel and screws complete all as specified and directed.

S&F in repair 100 mm butt hinges extruded brass with mild steel hing pin, bright polished and fixed, type B-11 complete all as specified and directed.

S&F in repair 75mm butt hinges extruded brass with mild steel hing pin type B-12, bright polished and fixed complete all as specified and directed.

S&F in repair mortice lock vertical type & 4 levers of size 100mm brass body with two keys complete all as specified and as directed.

S&F in repair mortice lock vertical type & 4 levers of 150mm brass body with two keys complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding and removing rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4, type B0 (using 12.5 mm graded stone aggregate) as in flooring for leveling course complete all as specified and directed

M&L for Non skid, joint free (edge cut) coloured ceramic tiles of 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles etc and laid over with and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and as directed.

M&L for 10 mm thick Vitrified ceramic tiles, light shade, double charged (square/recangular), area of each tile exceeding 0.36 Sqm but not exceeding 0.42 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450x300mmx7mm thick on wall/vertical surfaces such as skirting, dados and riser to steps etc laid over and including 10mm thick rendering in CM 1:4 finish set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified & directed.

M&L for Non skid, joint free (edge cut) coloured ceramic tiles of 7 to 8 mm thick (Square / rectangular), polished area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc laid over with and including 15 mm thick screed bed or bedding layer in CM (1:6), set and jointed in neat cement slurry and pointed with coloured cement to match the tiles complete all as specified and as directed.

M&L for 18 to 20mm thick Granite work (table rubbed and polished) of Lakha Red or Telephone Black colour for shelves, counter slabs, floors etc including 15mm thick backing of CM (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including demolition of (terrezo/PCC/granite of any description) and removing the rubbish from the site complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings etc not exc 15cm thick above or below ground level complete all as specified and directed.

M&L for PCC 1:3:6, type C2 (40mm graded stone aggregate) as in foundations filling and mass concrete complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection, path/hardstanding/subbase etc complete all as specified and directed

M&L for Chequered cement concrete tiles 25mm thick, area of each tile exceeding 0.05 sqm but not exceeding 0.09 sqm, set jointed and pointed in neat cement slurry with mixture of white cement and pigment in floors, laid over and including screed bed or bedding layer of 15mm thick CM 1:6 complete all as specified & directed.

M&L for Machine pressed precast conctete interlocking paver block of any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 Grade with grey cement and pigment laid and bedded on sand cushioning complete all as specified and directed. Note:-Sand cushioning shall be measured and paid seperately.

M&L Cement concrete tiles 20mm thick, machine pressed; laid over and including 20 mm thick screed beding in cement mortar (1:4), set jointed and pointed in neat cement slurry with mixture of white cement and pigment in floors, cut and polished etc complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L in repair cement concrete Type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) in kerb stone, copings, apex stones, anchorage blocks etc. (of any section as directed) with plain fair faces, including chamfered weathering, throating etc complete all as specified and directed.

M&L for preparing new concrete surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards any thickness and in any position including cover fillets complete all as specified and directed.

M&L for GI powder coated snap grid frame work for false ceiling of approved (ISI marked) make fixed to galvanised iron steel angle grid 600x600mm size suspended system fixed to GI framed work with main runner (32x24x6.5)mm cross tee (27x24x2.5)mm and moulding (19x19)mm of approved make and section as specified in SSR Part II with suitable hook/fasteners and GI/aluminium suspenders not less than 4mm dia upto 1200mm length @ 1.00m C/C minimum, ceiling system is to be fixed in water level without any sag including ceiling cleats made out of GI flat iron 40x3mm size 60mm long and expansion hold fastner 12.5 mm dia 40mm long complete all as specified and directed.

S&F 4mm thick HPSC pre prime non asbestos fiber cement building board of size 595x595mm with decorative finish fixed to GI powder coated snap grid frame work with screw in ceiling complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement and two coats of exterior emulsion paint over a coat of primer including taking down of cement plaster from any type surface complate all as specified and as directed.

S&F in repair 150mm floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Taking down existing aluminium doors/windows and re-fixing after tightening loose screws including replacement of unserviceable screws, aluminium beading, rubber packing, rubber bushes etc with and including taking down carefully glass panels & re-fixing the same and other hardware fittings such as hinges, tower bolts, handles, door closers/floor springs etc complete all as specified and as directed. Note:- (i) One Carpenter will be detailed by the contractor for attending above complaints on daily basis. Cost of which shall be deemed to be included in quoted rates. (ii) The Carpenter so detailed by the contractor will report to MES complaint cell at 0845 hrs morning to receive complaint slip from department (for all types of joinery complaints) from MES complaint cell and after rectification hand over the rectified complaints copy to the complain cell on daily basis. (iii) The complaints shall be rectified within 08 Hours. If contractor fails to detail above tradesmen a panel recovery@ Rs. 1000.00 per day shall be made to contractor and shall be recovered from RAR/Final bill.

S&F in repair powder coated aluminium anodised frame (minimum thickness of powder coating 50 micron) for doors with one or more rebates including jointing cleats for fixing etc. complete all as specified and directed.

S&F in repair powder coated aluminium anodised door shutters (Minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary aluminium anodised jointing cleats, glazing clips, ruber neoprene packing, aluminium anodised handles 2 Nos in each door, aluminium anodised hinges 03 No's, aluminium anodised Tower bolt 02 No's, Powder coated aluminum snap beading, screws etc. complete all as specified and directed.

S&F in repair powder coated aluminium wall partition (minimum thickness of powder coating 50 micron) work for partition (fixed portion) with extruted built up standerd tubular section/appropriate Z section and other section of approved make conforming to IS 733 and IS 1285 fixing with dash fastners of required dia and size including necessary filing up the gaps at junction i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling, CP brass/ stainless steel screws etc complete all specified and directed by Engr in Charge.

S&F in repair 25 mm dia SS drapery rods, fancy type with brackets, stops, rollers, side knobs etc complete all as specified and directed.

M&L for welding in repair exc 2.5 cm but n.exc 5cm in length, thickness of metal to be welded n.exc 6mm complete all as specified and directed.

S&F in repair mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F in repair venetian blinds in double layers roller type of approved colour including all accessories, fitting/fixtures required for fixing the same in windows complete all as specified and as directed.

M&L for repair and replacement of aluminium/wooden door & window glass pan rubber (4 sides of glass pan) in any position not exeeding 1.5 sqm (glass pan) complete all as specified and directed.

M&L for repair and replacement of aluminium door & window glass pan rubber (4 sides of glass pan) in any position exeeding 1.5 sqm (glass pan) complete all as specified and directed.

M&L for sand filling with a mix i.e 70% sand of medium grade and 30% saw dust for maintaining the slope of Butt range including watering and consolidation all as specified and directed by Engr in Charge. Note: Labour for lifting of sand from trench as per user requirement.

m/s meetu enterprises (BID ID -3347102)

aman construction & general suppliers (BID ID -3346457)

deva engineers (BID ID -3339043)

M/s M S Sharma and Co. (BID ID -3338789)