Chola musuem

EXCAVATION Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

All Kind of Soil - (Upto 2.00m depth from NGL)

All Kind of Soil - (From 2.00m to 3.00m depth)

All Kind of Soil - (From 3.00m to 4.00m depth)

FILLING WORKS Supplying and foundation and basement with GRAVEL in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator,watered and consolidated etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling crushed stone sand(M-sand) in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

PCC Cement Concrete 1:5:10 (One Cement, five crushed stone sand and ten broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three crushed stone sandand Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

Foundation and basement

Damp proof course with Cement Mortar 1:4 (One Cement and Four crushed stone sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used, finishing and curing etc. complete complying with standard specification.

FORM WORK Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Footing

Grade Beam

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Centering for curved surfaces of all RCC items of work

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

CONCRETE Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and basement

Super structure Ground Floor

First Floor

Second Floor

Providing and laying in position, standardised concrete Mix M-25 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 k9. of 20mm machine crushed stone jelly and with about (3'3 cu'm') 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg' of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).departmental officers

foundation and basement

Ground Floor

First Floor

STEEL REINFORCEMENT Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

MASONARY WORK Brick work in CM1:5 (one of cement and five of Msand) using chamber burnt second class ground moulded stock bricks of size 9” x 4-3/8” x 2-3/4” (23x11.2x7cm) for stair case steps including proper setting, scaffolding, curing etc. complete in all respects in all floors and as directed by the departmental officers

For Foundation and Basement.

Brick work in CM-1:6 following Cement Mortar using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specification.

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

Brick partition walls of 11.50 cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

For Superstructure in Ground Floor

Supplying and fixing WPC (Wood Plastic Composite) partition wall using approved quality WPC boards of minimum 18 mm thickness fixed over GI channel framework (Gyproc Xpert channels or equivalent) with necessary screws and fasteners, including proper alignment, leveling, and anchoring to floor, ceiling, and side walls to form a stable and rigid structure, ensuring a neat and uniform finish as directed by the Department officers; the rate to include cost of all materials, labour, tools and tackles, scaffolding, transportation, conveyance, wastage, and all incidental charges for completing the work in all respects as per standard specification and direction of the Engineer-in-Charge

JOINERIES Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 2000mm x 2400mm with following specification: a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW c. Shutter Thickness: 46mm d. Honeycomb: In-fill e. Glue Macroplast UR-7221 f. Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS 304 - Finish SS g. Door Closer with Standard Arm Finish: Silver h. Lock Set: Dead Lock with both side key i. Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating: Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l. Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n. Vision Panel 200 x 750mm 2 Hrs. Fire Glass Schott Pyran with Frame o. Rated Glass Schott Pyran with Frame p. Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, pastering, scaffolding all other conveyence as per standard methods and as directed by the Departmental Officers.

Fire rated metal door - FD1

Supply and erection of Single leaf Fire Rated Door with Frame having the dimension of 1200mm x 2400mm with following specification: a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW c. Shutter Thickness: 46mm d. Honeycomb: In-fill e. Glue Macroplast UR-7221 f. Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS 304 - Finish SS g. Door Closer with Standard Arm Finish: Silver h. Lock Set: Dead Lock with both side key i. Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating: Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l. Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n. Vision Panel 200 x 750mm 2 Hrs. Fire Glass Schott Pyran with Frame o. Rated Glass Schott Pyran with Frame p. Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, pastering, scaffolding all other conveyence as per standard methods and as directed by the Departmental Officers.

Fire rated metal door - FD2

Supplying and fixing of Hallow pressed Stainless Steel (Salem Stainless Steel) Door Frame (Box Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., SOR M0400

Supplying and fixing of solid core flush shutter with teakply on both side with teakwood lipping alround 35mm thick and with panelled acoustic in fill including cost of materials,labour charges etc.,Complete complying with standard specification.

Solid core flush door - D1

Supplying and fixing of solid core flush shutter with teakply on both side with teakwood lipping alround 35mm thick including cost of materials,labour charges etc.,Complete complying with standard specification.

Solid core wooden flush door - D2

Supply & Fixing of ALTERRA ALT 50 Frameless Glass Door (Single / Double Leaf) with toughened glass and door accessiories Frameless door Rebate Profile all around the door. Rebated Door Frame size 50x54mm design. Hardware - Dormakaba junior Office Hinges(3 nos) ,Studio Gala Locks (1no) in aluminium silver (EV1) finish and Dormakaba TS 89 Slide Channel Door closer with (as per EN 1154) and saddle plate for fixing on the Glass door . Glass Mounted Sweep seal or Door Bottom Seal. In case of Glass overpanel OHP100-SG Over Panel Door profile to be used.The hardware should be suitable for Glass thickness of 10/12mm.The Profile finish shall be as per Approved Architects specifications. Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 1.5 mm Gauge thickness Excluding 20 Micron of Anodizing. Max Door Height - 2700mm Max Door Weight - 80 Kgs

Double Leaf Door - (1500 x 2400mm) - D3

Single Leaf Door - (1200 x 2400mm) - D4

Supplying and fixing WPC (Wood Plastic Composite) partition wall using approved quality WPC boards of minimum 18 mm thickness fixed over GI channel framework (Gyproc Xpert channels or equivalent) with necessary screws and fasteners, including proper alignment, leveling, and anchoring to floor, ceiling, and side walls to form a stable and rigid structure, ensuring a neat and uniform finish as directed by the Department officers; the rate to include cost of all materials, labour, tools and tackles, scaffolding, transportation, conveyance, wastage, and all incidental charges for completing the work in all respects as per standard specification and direction of the Engineer-in-Charge.

Providing and fixing Automatic Sliding door operator, Make: DORMAKABA ES 200 (EASY) 6250 OR EQUIVALENT compliant with future European standards and produced according to the guidelines for power-operated windows, doors and gates, BGR 232, the UVV and the VDE regulations. TÜV design tested for Durability of 1,000,000 Cycles, Manufactured according ISO 9001, tested according to the low voltage guidelines, CE Compliant, fulfils DIN 18650 standards for Padestrian Safety, for framed glass door application with DORMA ST-Flex Profiles Systems, modular design including internal cover and with 12.52 mm Laminated glass for 1 Nos sliding door panels and 1 Nos fixed panels, both sliding & fixed panels with DORMAKABA ST-Flex framed profile system with Interlocking Seals.Operator & Frame Finish should be Silver Anodised, with operator dimensions (H x D) : 100 x 180 mm and of length as required to suit the opening sizes as given below. DORMAKABA ES200 Operators are of very sturdy design with Self balancing Panel suspension system and with Anti-Jump fitting.The track profile should be separate from the main profile for enabling reduction in vibration insulation. Microprocessor-controlled control unit, Self-learning, with adjustable parameters for opening and closing speed, hold-open time and opening and closing force, reversing when obstruction is encountered, Class of protection IP 20 with SMPS for Power regulation. Activators- DORMAKABA Nemo Motion + Nemo Dual ( Safety & Motion ) Pack, EM Lock - Fail Safe with CableProgram Switch with Key. Max Panel Weight Carrying Capacity of 1 X 200 Kgs. The system shall have constant power supply 230V+ 5%, 50Hz, AC . The requirement in total is as mentioned below:

Providing Wooden finish UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windowsshould be steel reinforced with 25 x 24 x 25mm steelreinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x102mm. The mullion should be of 60 x 74mm. Theprofiles should have co-extruded seals. Hardware: All the hardware like friction stays, handlesshould be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug

UPVC Ventilator : Supplying and fixing Wooden finish UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work SOR M0675

UPVC Window Specification: Supplying and fixing Wooden finish UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Departmental Officer before use on work . SOR M-0674 (P.NO:70)

Supplying and erecting pull and push type rolling shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc.,

HANDRAIL Supplying and fixing of wooden composite railing post of 75*75 with powder coated MS inserts 38*38*2 mm to be fitted on the floor through base plate with SxR 10x8 fus fischer as designed . Horizontal fins 60*42 fitted in between horizontal fins with aluminium clips and corroshield self drilling screw . all post top covered with specified wpc end cap & bottom with powder coated aluminium skirt as per drawing and specifications.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete M0651

Supplying and fixing Mild steel grills for windows, ventilators, etc., including priming coat

PLASTERING Plastering with Cement Mortar 1:5 (One cement and Five M-sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with griding machine and the surface shall be thoroughly cleaned out of dust and scrubbing sand paper (waterproof abrasive sheet) to give a smooth and eveen surface .any uneveness shall be made good by applying 1st coat of putty mixed with coat of putty after 6 hours of 1 st coat of putty and then sand papering ( waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly ,etc., complete complying with standara specifications and as directrd by the departmental officers.[The rates are inclusive of hire charges for grinding machine with machine with wheel ,cost of sand paper (waterproof abrasive sheer),two coats of putty ,scrapping the putty area to level the surface smooth, etc., complete]. The putty should be got approved br the Executive Engineer before use on work.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 20mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by dept officers.

PAINTING White washing three coats with best shell lime in all floors complete complying with standard specification and as directed , including gum, conjee, water, etc., complete in all floors complying with standard specifications

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

FLOORING Supplying and fixing superfine polished Ruby red or equivalent colour Granite slab 20 mm thick for Lift facia with bullnose edges are set in CM 1:3 10mm thick for base and pointed with the same colour cement etc complete. The rate inclusive of labour charges for laying & pointing curing etc. complete

Supplying and fixing pre polished Ruby red or equivalent colour Granite slab 20 mm thick for Pantry and wash basin counter with bullnose edges are set in CM 1:3 10mm thick for base and pointed with the same colour cement etc complete. The rate inclusive of labour charges for laying & pointing curing etc. complete

Paving the floor with best approved quality Honed finished kota stone slab of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality River washed kota stone of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality Leather finished Kota stone of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying and fixing Granite slab for Atrium area with Chola asia map set in CM 1:3 20mm thick for base and pointed with the same colour cement etc complete. The rate inclusive of labour charges for laying etc.The materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Waterjet cutting charges for the Atrium area with Chola asia map set in CM 1:3 20mm thick for base and pointed with the same colour cement etc complete. The rate inclusive of labour charges for cutting etc.

Supplying and fixing of Carpet of size 10 m x 6m for introduction hall of thickness 8mm . The rate inclusive of labour charges for laying etc.The materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality Mirror finished Kota stone of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.tile size -300*450*8mm

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200X800 of 18/20mm thick of Sadharahalli grey , synthetic grey,Paradise and similar varieties with machine cut edge laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (one cement and three sand)fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with matheing colouring pigments etc.,The granite stone slaba and other materials to be used Shall be got approved by the Executive Engineer Concerned before use on work,etc.,Complete as per Standard Speicification.

WATERPROOFING TERRACE WATER PROOFING Newly Constructed Roof/Podium with 2K PU Waterproof coating above 2000 Sq.m Providing and Applying two component Polyurethane based cold applied seamless waterproofing coating to the RCC surface like Roof & Podium area applied @2.1kg/m2 in single coat using 3mm notched trowel to achieve 1.5mm DFT, including a prime coat of solvent free, medium viscous, epoxy primer @0.2L/m2 and protection with 120gsm Geo-textile over the 7 days cured waterproofing membrane. The Waterproofing material shall have Solids > 98%, Tensile strength >6 Mpa, Elongation at break >600% as per ASTM D 412, crack bridging ability (no cracks up to 3.2mm) confirms to ASTM C 1305, Puncture resistance >300N as per ASTM E154, Shore A Hardness >70 as per ASTM D 2240, Adhesion to peel after water immersion as per ASTM C 794 at 5.2N. Resistance to root penetration.The finished cost to include surface preparation,making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 60gsm Geo-textile over the angle fillet when the first coat in still wet, treatment of cracks and laying 120GSM Geo-textile as seperation/protective layer over the fully cured PU coating completely as per specification.W0304

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

LIFT & OHT W.P Providing and laying water proofing treatment to the Rafts, Below grade slab, Lift pits,water retaining structures with fully bonded 1.5 mm thick HDPE waterproofing pressure sensitive adhesive membrane over PCC before laying raft concrete having higher puncture resistance of 1000N as per ASTM E 154,confirming to BS 8102 & IS 16471:2017, requirements of UG waterproofing structures. Laying adjacent sheets by keeping overlap of 75mm, end overlaps to be treated using double sided tape. The membrane shall have Tensile strength >25 Mpa as per ASTM D 412, Elongation > 500% as per ASTM D 412, Hydrostatic head resistance >70m head of water as per ASTM D 5385, Low Temperature Flexibility: -25 deg C, Peel Adhesion to Concrete >880 N/m as per ASTM D 903 Modified, UV Exposure > 45 Days. The finished cost including surface preparation completely as per specification. W0314

TOILET Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (1 Liquid: 2 Powder), to the RCC surface like bathroom, toilet, balcony & utility area applied @ 1.7kg/ m2 in 2 coats to achieve 1mm DFT, having Elongation at break >50% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80 N/mm2 as per ASTM D 4541, crack bridging upto 1mm as per ASTM C 836, Water penetration (5 bar pressure) as per BS EN 12390 for Newly Constructed Bathroom / toilet / balcony / utility with Cementatius Waterproof coating below 300 Sq.m The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification.

Providig and Filling the sunken portion with brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

FALSE CEILING GYBOARD FALSE CEILING Supplying and fixing in position of FALSE CEILING ARRANGEMENTS using hilux board plain sheets (10 mm thick) falseceiling arrangements with aluminium anodised ' T' Section and 'L' angle frame work of grid size 60x60cm with aluminium T section and 'L' angel of size 25x25x2mm thick and the same is supported @ suitable intervals by adjustable type 6mm dia MS rod with suitable threaded nuts suspended rods hung from ceiling at 120cm c/c in both directions and fixing Using Hilux Board Plain Sheets in the grid so as to give a seat to false ceiling including painting the 6mm dia MS rod etc.,complete complying with standard speificat-ions. Necessary opening and arrangements for fixing electrical fitings should be provided with suitable frame work etc., complete. v SOR (M-0618) PG.NO:58

Providing & Supplying durlum GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size 595mmx595mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fibre acoustical fleece. Approved make by Engineer-inCharge texture, design and pattern. The tiles should have Humidity/Moisture Resistance, Fire resistance.

Supply and Installation of Saint-gobain Ecophon Advantage E or Equvalent -15 mm thick, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having density 100 120Kgs/m3, which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 Black Shellout grid system

Supply and installation of Acoustical False Ceiling of Higher absorption nubby finish tiles, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8/ 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick T15 metal grid system. T15 metal grid system of 600 x 600mm module includes WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The Higher absorption Nubby finish tiles square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department officers. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specication. M-0622

Supplying and fixing of WPC false ceiling with GI channel frame work gyproc xpert channels with required support ,so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, Scaffolding, transportation, conveyance, etc., complying to standard specication.

Supplying and fixing plywood false ceiling with GI channel frame work gyproc xpert channels with required support and fixing 12mm thick commercial plywood century brand or equivalent brand and fixing 1mm thick laminate finish

Supply and fixing of UV printed wall stretch ceiling of images of size 5x2.5m to display in between columns in first and second floor,so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, Scaffolding, transportation, conveyance, etc., complying to standard specification.

Supplying and installation of Anutone / Topakustiks / Idea Tec / Wood Fit / Equivalent Brand of Acoustic Wooden Wall Panelling with fire retardant grade pine wood fibre slats of size 2430 x 128 x 16mm with lineal perforation of 2mm back lined with soundtex black acoustical fleece 0.27mm thick, 63 g / m2, tongue-groove edge for a seamless look, 5 test fire retardant grade with noise reduction coefficient not less than 0.75 NRC to absorb low and mid range frequencies from 125Hz to 4000Hz. GI strut CC50 frame work not more than 60 cm centre to centre using GI channels are fixed on the wall, over which an acoustic filling polywool material sound synth of 500 gsm density of 50mm thick has fixed and finally the panels are fixed and finished, so as to have an neat appearance as directed by the departmental offices. The cost includes cost of material, cost of Labours, scaffolding, transportation, conveyance, etc., complete complying to standard specication.M-0707

Providing and fixing Toilet cubicles made of 12mm solid compact laminate panels including doors & intermediate panels finished with textured melamine of ''nuvo series '' of Stylam makes conforming to ISO 2046 as per the detail drawings. This also includes providing and fixing in position necessary nylon & aluminium hardware as per manufacturers specifications & project design consultants instructions like handles, hinges, latches, indicators, top rail, connectors, hooks, knobs, brackets, U channels, thumbturn, locks etc. Provision to made in the cubical for fixing Toilet paper holder, Health Faucet etc., as directed by the project design consultants and as per the detailed drawings.

Supplying and fixing marble of size 0.61*1.22m,18/20mm thick in all floors for urinal partition including labour charges for fixing and polishing etc.,

STRUCTURAL GLAZING Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere M-0659

Providing and fixing dry cladding up to 10 metre height with 30 mm thick gang saw cut stone with machine-cut edges of uniform colour and size up to 1m x 1m, fixed to structural steel framework and/or with the help of cramps, pins etc., and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge.(The steel frame work, stainless steel cramps and pins etc. (shall be paid for separately.) ( DSR CODE NO:8.20.2)

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut stone)... using M.S. square/rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. (DSR CODE NO:8.21)

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gram), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge. (DSR CODE NO:8.22)

Providing and fixing stainless steel Anchor Bolts (Grade SS 304) of required size and length (typically 12 mm diameter × 100–150 mm long) including drilling holes in RCC/steel surfaces, insertion using approved chemical or mechanical fixing system, and securing with necessary SS nuts, washers, and sleeves. (MR)

Providing Design, detailing, CNC and waterjet cutting charges and traditional hand carving on natural stone panels to decorative motifs, as approved by the client or architect. (MR)

Surface preparation (sand blast) + two-coat epoxy system (zinc epoxy primer + epoxy topcoat) for MS frame protected behind cladding (externals).(MR)

MISCELLANEOUS Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Supplying & fixing SFRC MAN HOLE Cover of size 600x600mm etc complete complying with standard specification and as directed by the departmental officers (PWD -SOR :iTEM NO 295)

Supplying & fixing C I STEPS For sump etc complete complying with standard specification and as directed by the departmental officers (PWD -SOR :ITEM NO 250)

Supply & Installation Testing and commissioning of Sewage treatment Plant based on attached growth technology using the 'Moving aerated Biomedia Reactor (MBBR) process .complete mechanical and electrical items with stand by pumps. All criteria should meet relavant norms and codes of pollution board . complete as per stanard specification and as directed by by the competent authority .

STP (Inside) Waterproofing with Anticorrosive and Protective Coating (PWD–SOR–W0305): Providing and applying a two-component flexible polymer-modified acrylic cementitious waterproofing coating with a mix ratio of 5 parts liquid to 7 parts powder on the RCC surface of the STP tank, applied at a rate of 2.2 kg/m² in two coats to achieve a minimum dry film thickness (DFT) of 1.2 mm. The coating shall have an elongation at break greater than 120% as per ASTM D412, tensile strength greater than 1 N/mm² as per ASTM D412, adhesion strength of not less than 0.80 N/mm² as per ASTM D4541, and crack-bridging ability up to 2 mm as per ASTM C836. The rate shall include complete surface preparation, making coving of 50 mm × 50 mm at all right angles of wall junctions using polymer repair mortar, and laying of 45 gsm glass fibre mesh over the angle fillet while the first coat is still wet. All cracks shall be treated in accordance with the specification. This shall be followed by applying a 15 mm thick dimensionally stable, fibrous reinforced cementitious structural-grade dual-shrinkage polymer mortar as protective plastering at a rate of 29 kg/m². The protective mortar shall have a compressive strength of 38 MPa at 28 days as per EN 12190 and an adhesive bond strength greater than 1.5 MPa as per EN 1542. After plastering, water curing shall be carried out by sprinkling water three times a day for a period of 5–7 days. On the fully cured protective plaster, apply a two-component coal tar epoxy-based coating on the inside surface of the sewage and effluent treatment tank at a rate of 0.30 kg/m² in two coats to achieve a total DFT of 200 microns when fully cured. The coating shall exhibit scratch resistance for a 7 kg load as per ASTM D7027-05, chemical resistance against immersion in dilute acid, alkali, and salt solutions for 7 days as per ASTM C868, and salt spray resistance conforming to ASTM B117. The work shall be completed in all respects as per specification and direction of the Engineer-in-Charge.

UGT/OHT (inside) waterproofing with Antimicrobial Coating Waterproofing: Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface of the UGT/ OHT tank applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mmas per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. Followed by applying 15 mm thick dimensionally stable fibrous reinforced cementitious structural grade dual shrinkage Polymer Mortar on as protective plastering @ 29kg/m2. The material having Compressive strength of 38 MPa at 28 days as per EN 12190, Adhesive Bond Test, >1.5 Mpa as per EN 1542, followed by Water curing by sprinkling water for3 times a day for 5- 7 days. Followed by applying two component, water-based food grade epoxy resin coating on inside surface of Potable water tank having antialgae, antifungal, Non-toxic, hygiene cum damp-proof coating Certified by CFTRI as per 21 CFR 175 – 300 of US – FDA, having mixing Ratio (Base: Hardener: Water) – 1:1:1 to be applied @ 0.35 Kg/m2 in 2 coats. Ensure that this coating is applied over the protective plaster. The Waterproofing material shall have Specific Gravity:1.2, Water vapor permeance: 244.48 g/m2/24 hrs, asper IS 7809/Pt 2/1977, Adhesion strength: 2 N/mm2as per ASTM D 4541: 02. The finished cost to includesurface preparation completely as per specification PWD -SOR -W 0306

Manufacturing supplying and fixing in position of teracotta jally of size 20x20x5cm thick approved quality and design in cement slurry including cost of materials labour curing lifting fixing in position etc, complete complying with standard specification and as directed by the departmental officers in all floors.

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. and as directed by dept Officers.(PWD SOR Sl.No:394)

40mm PVC - 10kg/cm2 Pipes

50 mm PVC

Supplying and fixing the following dia PVC (SWR) pipe type B class conforming to IS 13592and relevant specials including packing the joints with rubber lubricant fixing them into walls with necessary GI Bolts and Nuts with special clamp made of MS angle/Flat including cutting, bending (excluding the cost of MS angle/flat) holding wherever necessary and making good of the dismantled portion with necessary connections to sanitary fittings etc., complete complying with relevant standard specification and as directed by the departmental officer. (PWD SOR Sl.No:394)

Soil Pipe - (110mm Pipe 6kg/cm2)

Wastewater Pipe - (75mm Pipe 6kg/cm2)

Wastewater Pipe - (160mm Pipe 6kg/cm2)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. cand as directed by dept Officers..

110 mm dia PVC- 4 kg/cm2 pipes

160 mm dia PVC- 4 kg/cm2 pipes

Supply and fixing of GM Gate Valve heavy type with necessary flanges, gaskets, nuts and bolts complete as required and shall be compatable with Composite pipes as applicable.etc., complete complying with relevant standard specification and as directed by the departmental officer. The quality and brand Gate Valves is to be got approved by the Department officer before fixing.(PWD SOR Sl.No:394)

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

80mm dia

Providing and fixing GM Non return valve as per IS BS 5154 and related IS Specifications

50mm dia

65mm dia

80mm dia

Supplying and fixing of CP Two Way Bib Cock with Health Faucet including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be Check before use).

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Departmental Officer before use on works.)

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittingssuch as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the departmental officer before use on works)

Supplying and fixing in position white / colour glazed Indian Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., complete with all fittings (The IWC with all accessories should be got approved by the departmental officer before use on works)

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the departmental officers before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the departmental officers before use on works) (Cast Iron Nahani Trap of size 100 x 75mm with stainless steel gratings)

Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in SFRC cover slab of size 300 x 300mm over using 40mm size brick jelly and brick masonry wall 115 mm thick using fly ash bricks of size 23x11x7cm in cm 1:5 (One of cement and five of sand ) plastered with CM 1:3 (One of cement and three of sand) 12mm thick Including fixing cover slab fixing in position curing finishing etc., All complete complying with relevant standard specification and as directed by the departmental officer.

Construction of Inspection chamber of following sizes with brick jelly concrete 1:8:16 ( one of cement eight of sand and sixteen of broken brick jelly using 40mm gauge broken brickjelly 15cm thick for foundation and 23cm thick brick masonry in C.M. 1:5 ( One of cement and five of sand) using fly ash bricks of size 230mm x110mm x70mm, plastering with cement mortar 1:3 ( One of cement and three of sand) 12mm thick on both sides top and bottom including earth work excavation RCC 1:2:4 ( One of cement two of sand and four of 20mm gauge hard broken stone) Including SFRC Cover Heavy duty collor with slab of required size fixing in position curing finishing etc., complete complying with relevant standard specification and as directed by the departmental officer. (Inspection 0.60x0.60m (inside opening))

Inspection Chambers (0.60x0.60x0.45-1m depth)

Inspection Chambers (0.90x0.90x1-1.5m depth)

Supply and fixing 5HP submersible pump set asper ISI specification with isi mark hyduralically testing and commisioning of submersible wet type suitable for sump with pressure gauge and necessary length of 2 nos of pp from pumpset to the top of the sump and other required accessories etc complete in all respect and as directed by the departmental officers, the motor and the pumpset supplied should satisfied the following duty conditions etc complete complying with standard specification and as directed by the departmental officers.SOR(M1068)

Supplying and fixing of PVC / Fibre Glass Framed 5.5 mm thick Mirror, Shelf Type with Hard Board Backing of size 1200x450mm including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).

Supplying and fixing of CP Robe hook with with CP Screws including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).

Supplying and fixing stainless steel paper holder with necessary fixing material paper roll etc.complete.

Supplying and fixing paper dispenser with necessary fixing materials etc.

Supplying and fixing electrically operated automatic hand drier with necessary fixing materials etc.

Supplying and fixing Grab bar 450mm Long with necessary fixing materials . .

Supplying and construction of Rain water recharge pit with filter media, recharge bore, top slab complete as approved recharge pit drawing

Providing and laying non-pressure class NP2 RCC Hume pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1 part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

Supplying, laying and jointing CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Internal & Vertical

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

20mm dia

25mm dia

32mm dia

40mm dia

Wastewater Pipe - (160mm Pipe)

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.M-0846

Providing and fixing of approved make 50mm dia, Brass float valve, complete brass body contruction, PN6 rating, with SS ball. The scope of work includes terminating the OHT inlet pipe and positioning for smooth operation.

Providing and fixing GI. puddle flanges (IS 1239) fabricated out of 6 mm thick M.S. plate of size 300 x 300mm plus dia of pipe of 750mm long pipe pieces fixed to RCC wall of water tanks. Including painting with two coats of primer complete as required. The entire fitting shall be hot dipped galvanized.

25mm dia

40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

150mm dia

200mm dia

Supplying, installing, testing and commissioning approved make Brass pressure reducing station including pressure reducing valve ,3 Nos Isolation valves, 2 Nos Pressure Gauges with union, flanges etc., complete.

65mm Dia

50mm Dia

Supplying, Installing, testing & commissioning approved make water treatment plant of capacity 2000 LPH complete compluying as per standrad specification

Supplying, fitting, fixing Installation of Water cooler Aqua guard Storage Cooler-cum-Purifier Model- AG Green Pure Chill 120SS, with storage capacity 120 Ltrs., with - in built purifier (UV based) etc. complete and all as per direction of Engineer-in-charge.

Drilling of bore wells anywhere in Tamil Nadu including transportation from one place to another within Tamil Nadu in aluvial soil sedimentary strata of clay and M-sand stone shale pebble boulders etc. By first taking a pilot bore of 140 / 150 / 200mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs fuel, labour and drilling bentonite and water required for drilling at site. Site will be shown by the departmental officers including construction of mud pit

Upto 60m Depth

From 60m to 90m Depth

From 90m to 120m Depth

From 120m to 150m Depth

From 150 m to 180 m depth

From 180 m to 210 m depth

Reaming from 140/150 mm dia pilot bore to 300mm dia bore as directed by the departmental officers

Upto 60m Depth

From 60m to 90m Depth

From 90m to 120m Depth

From 120m to 150m Depth

From 150 m to 180 m depth

From 180 m to 210 m depth

Supplying and inserting PVC casing pipe (CM) 160mm diametre with / without slots for inserting in the drilled hole including jointing the pipes, etc., complete as directed by departmental officers

160mm ID plain casing pipe with slotted

160mm ID plain casing pipe with out slotted

Labour charges for inserting PVC casing pipe assembly CM 160mm diametre with/without slots for inserting in the drilled hole including welding the jointM-sand packing annular space with pebbles of size and quality as approved by the the pipes, etc., complete as directed by departmental officers

Charges for developing bore well with air compressor of 600 CFM capacity including transportatin labour and fuel charges for compressor as directed by the departmental officers and conducting yield test by 'V' Notch method

Supplying and fixing 160mm dia PVC End-Cap for bore-well with ISI mark

Supplying and fixing of 40mm HDPE Hose of approved quality and best variety comforming to ISI mark of suction pipe for sub-mersible motor as directed by the departmental officers

Supply & run of single phase 2.5 sqmm copper cable as per standard specification etc.,

Supply & fixing of erecting single phase deep well 5.00 HP20 stage submersible pump of best approved quality and make with ISI mark suitable for 415/440 v -50 HZ AC electrical supply with all accessories including panel boards of required size having 1 No -30 Amps TPI (switch 1 No of DOL starter 1 No ammeter 0 to 30 Amps -1 No of voltmeter 0 to 500 volts with control switch -3 Nos of indicator lamps suitable cables (55 metre)2 set of 1-1/2" clamps nippleM-M-sand giving electrical conditions with neccessary flexible pipe etc., complete (the pump should be tested minimum of three days at contractors own cost)(Excluding GST)(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact etc.. complete

Labour charges for erection of Submersible Pump with motor (Upto 5 HP TWAD Board Schedule of Rates Item No:17B)

Supplying and fixing in position of 2''x2'' size chain link fencing 10 gauge and fixing with M.S. Angle post using 16 gauge G.I. Wire including running the 2 ply and 4 pin G.I. barbed wire 12 gauge at bottom, middle and top of M.S. angle posts (As stiffner to the chain link fencing) etc, complete complying with standard specification

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump rated for 2280 LPM at 70 metres head with Electrical Motor of 60HP of 415 volt, 3 phase connection complete with base plate and accessories. (Make Kirloskar or Equivalent). The rate inclusive of neessary vibration, bed mounting, etc., as per standard specifications and as directed by the Departmental Officers (Sprinkler & Hydrant Pump )SOR(M-0836)

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of followings complete in all respects as required. 1 No. horizontal split casing centrifugal type fire pump capable of delivering 2280LPM against a total head of 70 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / utlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring, etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dynamo, solenoid switches etc. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter, after filter etc.. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition. SOR(M-0835)

Supply, erection, testing and commissioning of 180 LPM, 70 metres Head Pressurization Pump with 10HP electrical motor of Kirloskar make with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIRLOSKAR / EQUIVALENT. Jockey Pump SOR(M-0844)

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: HGURU / ISI MAKE / EQUIVALENT. SOR (M-0828)

Pressure Switch (Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.)SOR(M-0829)

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

250mm dia SOR(M-0810)

200mm Dia SOR (M-0810)

150mm Dia SOR(M-0812)

100mm dia SOR(M-0813)

80mm dia SOR(M-0814)

65mm dia SOR(M-0815)

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table ‘E’, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT SOR(M-0819)

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

100mm Dia SOR(M-0818)

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR /EQUIVALENT. SOR (M-0846)

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Butterfly Valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

100mmDia SOR (M-0818)

150mm Dia SOR(M-0817)

Providing, fixing pipe supports 100mm dia from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification. SOR (M-0847)

Supply, erection, testing and commissioning of MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Officer Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard by the Departmental Officers. Make: JINDAL / EQUIVALENT

Hydrant Pipe

250mm diaSOR(M-0796)

200mm dia SOR(M-0797)

150mm diaSOR(M-0798)

100mm dia SOR (M-0799)

Sprinkler Pipe

150mm Dia SOR(M-0798)

100mm Dia SOR (M-0799)

80mm Dia SOR (M-0800)

65mm Dia SOR(M-0801)

50mm Dia SOR(M-0802)

40mm Dia SOR (M-0803)

32mm Dia

Supply and laying of 300mm Dia RCC hume pipe SOR(M-0432)

300mm dia RCC Hume Pipe SOR(M-0432)

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.SOR(M-0790)

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges,neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT. SOR(M-0794)

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE SOR (M-0791)

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.SOR(M-0792)

Branch pipe(Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT)SOR (M-0793)

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supply and fixing in position of Fire Fighting Duct Window having proper glass window type double door with universe open key, painted inside white and outsid post office red for the sizes of 1300 x 900 x 500mm (L x B x D) fabricated using 25 x 3mm MS 'L' Angle and all sides covered with 2mm thick MS sheets, suitable arrangements to kept 2 Nos. of Fire Fighting Hoses and 1 No. Branch Pipe, mounted in fire duct using anchor fasteners, etc., as per standard specifications and as per directed by the Departmental Officers. SOR(M-0843)

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of 150mm dia.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT. SOR (M-0795)

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.SOR (M-0839)

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.SOR (M-0841)

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT. SOR (M-0845)

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo /Equivalent) SOR (M-0770)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent) SOR (M-0771)

Supply, fixing, testing & commessioning of dial type (150mm) Glycerin filled pressure gauge with isolation ball valve suitable for working pressure of 250 PSI with no syphon, cost shall be inclusive for providing any short pieces, nipples, elbows etc all complete as per standard specification and directed by the departmental officers

Hooter (Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)SOR(M-0772)

Supply and fixing of stored pressure ABC (Mono Ammonium Phosphate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., Including conveyance, all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY / FIRST / EQUIVALENT SOR (M-0851)

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc. complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY / FIRST / EQUIVALENT SOR (M-0852)

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers -SOR(M-0842)

Supply and fixing of Carbon-di-Oxide Gas Type 4.5 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers.

Supply and kept in position of Trolley Mounted Type 22.5 kg. Carbon-di-Oxide Fire Extinguisher as per IS15683, complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST /EQUIVALENT SOR(M-0854)

Supply and fixing of Aqueous film forming foam 9lts. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers.

Supply and fixing of DCP (Dry Chemical Powder ) Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers.

ELECTRICAL WORKS Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) (Higher End )

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) (Higher End.)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point (Higher End )

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) (Higher End)

Supply, fixing of 9W Recessed light standard round design in white PDC Aluminum Housing with high performance LED and driver (For Gallery )

Supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling from ceiling with PVC unsheathed FRLS copper leads from terminals to the fitting. (Lobby, Introduction Hall, near Stairs, near lift)

Supply and fixing of 18W LED Square type Surface fitting with LED (Higher end) on wall or ceiling with PVC unsheathed FRLS copper leads from terminals to the fitting. (Staircase & Toilet )

Supply and fixing of 70W SURFACE MOUNT high bay Light Output of wattage 80W and CCT of 5700K and complete as directed by the competent authority. (Higher end) (Porch)

Supply and fixing of 20W FOCUS LIGHT (TRACK) BLACK- high efficiency track light of CCT of 5700K with reflector optics for optical excellence,1m track(black), 1m suspension for track (black),straight connector and complete as directed by the competent authority. (Higher end) (Gallery)

Supply and fixingof 5W PENDANT LIGHT-traditional lantern light made of MS black powder coated housing and glass with CCT -2700K and complete as directed by the competent authority. (Higher end) ( Corridor )

Supply, fixing of 24 W down light with Deep insert sheet Collimator ring down light of CCT 5700 K for low gkare and complete as directed by the competent authority (Higher end).

Supply and fixing of 24W SPOT LIGHT ,beam angle 36 degree, Vertical Tilt 30 degree and complete as directed by the competent authority.(Higher end) ( Atrium )

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb ( Lift )

Supply and fixing of 36W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (Office)

Supply and fixing of 40 W 4’ LED SBT LIGHT complete on wall or ceiling with with PVC unsheathed Copper leads from terminals to the fitting (Higher end) , suspension for light (black). Optical cover type Polycarbonate and complete as directed by the competent authority. (Archive, Lab, Passage, Store)

Supply and fixing of Environmental friendly, new generation, energy saving, decorative IP66 5W LED facade light using COB LED as light source on suitable support with connection and complete as directed by the competent authority. (Domes )

Supply and fixing of Environmental friendly, new generation, energy saving, decorative IP66 15 W LED facade light using COB LED as light source on suitable support with connection and complete as directed by the competent authority.

Supply and fixingof 8W IP65 rated Bollard fitting (Higher end) with aluminum casing and polyester powder coated for rust and weather resistance,height-500mm and complete as directed by the competent authority.

Supply and fixing of 100W floodlight (Higher end) with integrated driver , PDC aluminium constructed recessed mounted under canopy luminaire with superior aesthetic finish,10KV SPD & ingress protection of IP66, 600x600 mm frame and complete as directed by the competent authority.

Design, supply, erection, testing, commissioning and handing over of 16 mtrs High Mast Structure with required number of continuously tapered hot dip galvanized steel polygonal sides sections with telescopic strip joints to a total height of 16 meters capable of sustaining the maximum wind pressure at the erection site with single flange base plate secured welded in the bottom of the base mast section with vertically movable hot dip galvanized lantern carriage and accessories such as electrical junction box brackets for providing 8 Nos. of flood light luminaries with control gear box complete head frame assembly, Pulley drive, stainless steel wire rope single/double drum self-lubricating winch arrangement suitable for raising and lowering the luminaries carriage ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and anchor plates and templates including supply and fixing the following accessories in the Mast.

a) Design and casting of suitable foundation with 1:2:4 mix RCC concrete with 30 cm projection above the ground level with 1 metre Width x 1 metre Length and 2 metre depth with necessary galvanized foundation bolts nuts and washers and dump plate enclosing the bolts for the High Mast considering the safe soil bearing capacity at site - 1 set.

b) High powered power tool complete with hand held control panel and motor with push button type remote control switch suitable for 3 phase 415 V 50 HZ for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch - 1 Set

c) Feeder pillar box comprising 0.90 m x 0.45m x 1,20m floor AI frame with 63 A TPN main switch 1 no , 63 A fuse unit 3 nos. 63 A power contactor with automatic timer arrangements and reversing starter for the 3 phase motor - 1 Set.

d) Neon aviation obstruction light - 1 No

e) 2 Nos of special GI earth electrodes with copper plate 300 x300 x 3mm and copper flat (1”x1/4”) interconnection as per ISS complete with earth connection - 1 set.

f) Hot dip galvanized lightning arrestor - 1 No.

g) Flood light luminaries of specially Heavy type water poof Dust proof integral luminaries fitting provided with 200 Watts LED Light fitting Crompton / Philips make or Equivalent with 200W LED Bulb with drives, Alglas coated reflectors, with cable connection etc. complete as per standard specification. - 8 nos [SR]

Supply and fixing of 18W LINEAR WALL WASHER LIGHT: wattage 18W ,CCT of 3000K with an IP67 driver and glass diffuser (Higher end) and complete as directed by the competent authority.

Supply and fixing of 18W LINEAR RGB WALL WASHER LIGHT: wattage 18W ,CCT of 3000K with an IP67 driver and glass diffuser (Higher end) and complete as directed by the competent authority.

Supply and fixing of Neon Flex 9W IP 66 Rated (K-Lite / equivalent ) of suitable length with necessary connections complete with all accessories etc., complete complying with standard specification and as directed by the department officers.

Supply and fixing of environmental friendly, new generation, energy saving, decorative IP66 5 W LED facade light /UP-DOWN light using COB LED as light source on suitable support with connection (Higher end). and complete as directed by the competent authority.

Supply and fixing of 7W 4 DIRECTIONAL Decorative Wall Washer, Four Headed and Four Ways Light Throw (Higher end) and complete as directed by the competent authority.

Supply and fixing of 9W RGB BRICKLIGHT with necessary accessories (Higher end) and complete as directed by the competent authority.

Supply and fixing of 3W STEPLIGHT: compact, robust, and non-corrosive aluminum body light with high lumen output LEDs. CCT-5700K (Higher end) and complete as directed by the competent authority.

Supply and fixing of 20W 2' LED Mirror light fitting with LED (Higher end) on wall with necessary accessories with PVC unsheathed copper leads from terminals to the fitting and complete as directed by the competent authority.

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 30W LED POLE Street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour.

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete (Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 375 mm (15") sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making of the wall.

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep (light duty) AC exhaust fan.

Supply and fixing of 2nos.6A two module 3 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and fixing of 3nos.6A two module 3 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End).

Supply and fixing of 1 no 6/16A two module socket, 1 no 16A one module cover plate (Plastic) on Suitable module Concealed Box (GI) in flush with wall with connections. (Higher end).

Supply and fixing of 2 nos. of 16A one module socket, 2 no 16A one module switch on suitable module surface mounting Box ( GI ) with module cover plate (Plastic) on wall with connections. (Higher End).

Supply and fixing of 20A Flush type DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug).

Supply and run of 2 of 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour'.

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copperwire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and run of 4 of 6sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one No 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one No 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in Each segment) and seperate provision for MCB / Isolators ( totally 24 Nos) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with Earth connection only.

Supply and fixing of 4 way Triple pole and neutral vertical MCB DB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P RCCB as incoming and 4 nos. 32A TP MCB as outgoing in flush with wall with earth connection only. (Higher End).

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB with IP 43 DB as per IS 8623 III & Impact resistance IK09sheet steel enclosure distribution board with double door (metal) with 1 no. 125A 4P DPX MCCB as incoming and 4 nos. 63A TP MCB as outgoing in flush with wall with earth connection only. Higher End (For Power DB-14) Same as ELDB-5Nos.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soilsand to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and run of 50mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

Supply and Laying of 3 1/2 x 300 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated ata depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 1/2 x 300sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3-1/2 x 300 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 3-1/2 x300 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and laying of 3 1/2 x 240 sq.mm PVC armoured LTUG cable i suitable size HDPE pipe in a trench to be excavated ata depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 1/2 x 240 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3 1/2 x 240 sq.mm. PVC armoured LTUG cablewith necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of brass cable gland for 3-1/2 x240 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and Laying of 3 1/2 x 150 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 1/2 x 150sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and fixing of brass cable gland for 3-1/2 x150 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 1/2 x 70 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3-1/2 x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of brass cable gland for 3-1/2 x70 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 1/2 x 35 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of brass cable gland for 3-1/2 x35 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and Laying of 3 1/2 x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 1/2 x 25sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3 1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of brass cable gland for 3 1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 4 x 16 sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 4 x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and fixing of brass cable gland for 4 x 16 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 4 x 10sq.mm PVC LTUG armoured Alu cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 4 x 10 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of brass cable gland for 4 x 10 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and installation of sheet steel 2.5mm /2mm thick consisting 2 nos. side rail s with runs at every 250mm interval and complete with associated accessories such as coupler plates , Tees , long bend, elbows etc.Hot Dip Galvanized 65 microns tthick cable tray of size 35 x 35 x 5mm GI angle with 600mm width cable tray and 10mm threated GI rod supports upto 450mm with cable tray and they supports should be at 1.5m interval and grouting the supports in wall/ ceiling / floor as per the requirment in confimating with specification all as required size 150 x 50 x 2.0 mm thick.

Supplying, erecting, connecting and commissioning of 8mm Aluminum Solid Round Conductor

Supplying, erecting, connecting and commissioning of Metal Roof Conductor Holder for 8-10 mm Aluminium Solid Round Conductor for horizontal Air terminal above metal sheet with fixing screws

Supplying, erecting, connecting and commissioning of Stainless steel Cross Connector for 8 mm Solid Round Al. Conductor & 10 mm Copper coated conductor

Supplying, erecting, connecting and commissioning of Stainless Steel Clamping Shoe to interconnect 8 mm Air terminal and down conductor for metal buildings

Supplying, erecting, connecting and commissioning of Expansion Piece with connector to compensate the expansion and contraction of 8 MM Aluminium Solid Round Conductor during temperature variations to be provided on conductors length over 20 meters with Expansion Piece Connector for to connect Solid Roung Al. Conductor at both ends.

Supplying, erecting, connecting and commissioning of Lightnig counter - LCD screen shows the number of lightning strikes, hour and date of lightning events. Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years with necessary with required accessories.,

Supplying, laying and connecting the following 32x6mm Copper Flat laid from FC to Earth pit

Supplying, installing and connecting a 3 Mtr. Long 40 mm. dia GI Pipe in an Earth Pit Size of 600x600x3000 mm. filled with salt and charcoal mixed with sand inalternatelayers 150 mm.each upto a height of 2500mm. from bottom. The pipe shall have provision for watering through a funnel. It shall also have provision for connecting 25 x 6 mm.Copper Flat on two sides. A masonry structure shall be constructed to a depth of 750 mm. and a heavy duty CI Cover shall be used to cover the pit. The cost of digging and back filling shall also be included. Sand, salt and charcoal are in the Contractor's scope.

Supply & fixing of type 10 CCT earth terminal test box

11 KV OUTDOOR RING MAIN GEAR (RMG) Supply Erection testing and commissioning of 11KVA 25KA 630Amps 3 Panel HT outdoor RING MAIN GEAR Switch board suitable for outdoor installation comprising two incomer panels with Air Break /load breaks switches and one outgoing panel with vaccum circuit breakers complete confirming to TANGECO standard specification and as per the following specification with Mechanical inter lock between incomers

1.Supply and Erection of 1 no. draw out type 11KVA 25 KA 630 Amps Horizontal draw out /Horizontal VACCUM CIRCUIT BREAKER Fitted with motor (230 V AC )operater spring charged Mechanism, with ON and OFF mechanical indicator Anti pumping Device 110 V DC Shunt trip and closing coils (DC source of supply to be derived from a power pack suitable for three triping and two closing operation incorporated on Incoming panel only) Mechanical operation counter,4 No + NC spar AUX contact with contact multiplication contractor for customer use. Automatic Safety shutter, Mechanical close /Trip knob Mechanical ON/OFF Indication, operation andle,230V AC to 110V DC Power pack operation Handle.

2.Supply and Erection of 2 nos. of 11KV 630 Amps 25 KA HT Air Break /Load Break switch with mechanically inter locked each switch, front operated spring assisted manual closing mechanism 2 NO +NC Aux contact.

3. 11KV /Root 3/110V Root 3- Three phase 3 limb 50 VA Class 0.2 Resin cast Draw out type potential Transformer complete with HT and LT HRC Fues with sealing arrangement - 3 NOS.

4.Current Transformer of suitable Ratio /5-5A Dual core (core 1-5VA clas 0.2 for metering &bcrore 2-15VA 5 P20 For protection -3 nos

6. Protection: IDMT two over current and one earth fault Relay with high set Inst Elements 1.3 seconds 1No Master Trip relay (Megawin MVAJH 13 equivalent) -1 No.

7. Breaker ON/OFF indication LED type 2 Nos. AutonTrip /Healthy Trip and spring charged indication LED type -3 Nos phase indicating Lamps.

8. TNC Breaker control switch -1No Local Remote seletor switch -1No-

9. panel Mounting Surge Arrester 9KV,10KA -3No.

10. 630Amps copper bus bar PVC sleeved & requried.

11.Submission of RMG Drawing to TANGEDCO panel earthing arranging CT/PTInspection and obtaining TANGEDCO aproval (DATA-X)SOR(M - 1958) Including Civil work for RMG Plinth of height 150mm Foundation 2.5Mtr x1.55Mtrx150mm, Liasioning charges for TNEB MRT Higher official Inspection at manufacturing unit factory, Transport charges and Erection, testing and commissioning charges.

11 KV INDOOR VACCUM CIRCUIT BREAKER Supply Erection,testing and commissioning of 11KV, 25KA, 630Amps HT INDOOR THREE PANEL VACCUM CIRCUIT BREAKER For Consumer POS With 18KV, 10kA Polymer Type Surge Arrester. Horizontal Draw Out VCB fitted with Manual / Motor Operated spring charging mechanism with 230V AC Motor & Motor Control Switch, Mechanical ON/OFF indicator Operation Counter, Automatic safety shutters & push Shunt trip Coil, 110V DC. Closing Coil, 110V DC. Spare auxiliary contact, 6NO+ 6NC. Anti pumping Feature, 110V DC. Power pack 230V- 110V AC/110V DC Potential Transformer, Three Phase, Resin cast, Dry type, Fixed Potential transformer with one set of HTFS/LTFS and one no. Neutral Link of Ratio: (11KV/V3)/(110V/V3) Current Transformer, Single phase, Resin Cast, Dry Type Current Transformer,

Core 1: for meter, Cl-0.5s, 5VA,

Core 2: for protection, Cl-5P20, 15VA. Metering, MFM, Digital Ammeter & Digital Voltmeter With Fault Level tripping & Fault Recording. Protection, Numerical Non-directional IDMT. (M - 1954) Including Civil work for RMG plinth of height 150mm foundation 7.5m x 1.55m x 150mm, liasioning charges for TNEB MRT Higher official inspection at manufacturing unit factory, Transportation charges and Erection , testing and commissioning charges.

11 KV INDOOR VACCUM CIRCUIT BREAKER Supply Erection,testing and commissioning of 11KV, 25KA, 630Amps HT Outdoor Single PANEL VACCUM CIRCUIT BREAKER For Consumer POS With 18KV, 10kA Polymer Type Surge Arrester. Horizontal Draw Out VCB fitted with Manual / Motor Operated spring charging mechanism with 230V AC Motor & Motor Control Switch, Mechanical ON/OFF indicator Operation Counter, Automatic safety shutters & push Shunt trip Coil, 110V DC. Closing Coil, 110V DC. Spare auxiliary contact, 6NO+ 6NC. Anti pumping Feature, 110V DC. Power pack 230V- 110V AC/110V DC Potential Transformer, Three Phase, Resin cast, Dry type, Fixed Potential transformer with one set of HTFS/LTFS and one no. Neutral Link of Ratio: (11KV/V3)/(110V/V3) Current Transformer, Single phase, Resin Cast, Dry Type Current Transformer Core 1: for meter, Cl-0.5s, 5VA,Core 2: for protection, Cl-5P20, 15VA. Metering, MFM,

Digital Ammeter & Digital Voltmeter With Fault Level tripping & Fault Recording. Protection, Numerical Non-directional IDMT. Transportation charges and Erection , testing and commissioning charges.

Supply and Laying of 300 sq.mm. 3 core HT XLPE 11KV (E) SISMV11U3 x 3002424 armoured cable in suitable size RCC cable truf in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 300 sq.mm. 3 core HT XLPE 11KV (E) SISMV11U3 x 3002424 armoured cable on post or on wall with MS Clamps.

Supply & Fixing of 300 sq.mm. 3 core HT Cable Indoor Terminations XLPE 11KV (E) - Belted PILC Cables - EPKT 4961 .

1000KVA TRANSFORMER Supply erection testing and commissioning of 1000KVA/11KV /433V off load tap changing copper wound outdoor type distribution transformer conforming to relevant ISI 180 Level -1 standard and fitted with the following: a)HV cable end box suitable for Connection 3 core 300 Sq mm 11 KV, XLPE HT cable b) LV cable end box suitable for connection 3 runs of 31/2x300 Sq mm LTUG Cable c)Conservator with shut off valve d) Conservator drain plug valve e) Dehydration silicagel breather f) Expansion vent g) 4Nos plain rollers H) Thermometer pocket with dial type thermometer with caillary tubing with maximum reading position. i) Drain plug/valve) Filter valve j) Oil filling hole and cap k) Oil level gauge l) two body earhing terminals m) Rating and terminal marking plate n) Lifting hooks /lifting eyes,jacking pad to facilitate movement of transformer and easy handiling-1 No (Each)

n) Lifting hooks /lifting eyes,jacking pad to facilitate movement of transformer and easy handiling-1 No (Each) n) OFF load hand opereted tap changing switch at standing height from ground level. o) Tapping on primary widing for voltage and vaiation 5% to +5% p)Neutral on LV side to be available for 4 wire supply and brought out thought bushing for earthing q)Air release device r)The transformer should be supplied with first filling of oil All removable cover shall be provided with weather proof hot oil from the tank Sakthi/Rowson /Voltech /IPL )/35i Eco power/eq Including Charges for civil work and unmovable for the transformer wheel arrest for AI frame work with fixing on the transformer 100mm x 50mm channel provided, Transportation and transit insurance @2%, Erection , testing and commissioning charges with Test report

Supply, erection, testing and commissioning of 1600A draw out type floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following with Thermal Magnetic Release MCCB’s and 2 Nos. ACB as Incomer units , with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with

4Nos.2Runs 2” X 1/2” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/4 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set Incoming 1)Supply and fixing of 2 Nos. 1600A 4 pole 50 ka , microprocessor based, EDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules in force with inter connection and terminations as required in specification. Bus Coupler:- Supply and fixing of 1 No 1600A basic rating 4 pole 433 VLT ACB to IS-1394721EC60947-2 600VAC with all accessories for standard horizontal type ACB equipped withMicroprocessor based SR18G(w/o protection).

Outgoing 1) Supply and fixing of 800A 4 Pole ACB -2Nos 2) Supply and fixing of 630A TP ACB -2Nos 3) Supply and fixing of 400A FPN MCCB-6 Nos. 4) Supply and fixing of 250A FPN MCCB-1Nos. 5) Supply and fixing of 63A TP MCCB-2Nos 6)125A 1No TP MCCB Inter connecting the all LT ACB’s and MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC,300N class 0.5 flush mounting L&T or equivalent make–ModelER300N.Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning (L&T,C&S,SIEMENS,ABB) ( Data 35)

Supply and erection of 200 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 9 stage, (at 0.95 lag), made up of powder coated, 16 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3

seconds with a LCD display to show the following Parameters. a. Vr – R phase Line Voltage b. Vy – Y phase Line Voltage c. Vb – B phase Line Voltage d. Ir – R phase Line current e. Iy – Y phase line current f. Ib – B phase Line Current g. KW – Present Kilo Watts h. RKVA – Present KVAR Demand i. KVA – Present KVA j. PF – Present Power Factor k. Number of Capacitor bank ON/OFF l. Provision to indicate the imbalanced load m.Provision to indicate the change in phase Sequence n. The APFC Panel Should also have built in protection for current imbalance. For high Voltage/Low Voltage cut off, single phase Preventer, provision for inductor coil to cater the in-rush currents, line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Eight Stages of Automatic Power Factor control panel with necessary connection. Make. (Matrix /L&T /or equivalent ( Data 36)

800 ESSB 1 Supply, erection, testing and commissioning of 800A draw out type floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following d sine with Thermal Magnetic Release MCCB’s and 2 No. ACB as Incomer units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4Nos.2Runs 2” X 1/2” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set

Incoming 1)Supply and fixing of 1No 800 4 POLE ACB , microprocessor based, EDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules in force with inter connection and terminations as required in specification.

Outgoing 1) Supply and fixing of 400A TPN MCCB-2Nos 2) Supply and fixing of TPN 250A MCCB 2Nos. 125A TPN MCCB 2Nos-. Inter connecting the all LT ACB’s and MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC,300N class 0.5 flush mounting L&T or equivalent make–ModelER300N.Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning (L&T,C&S,SIEMENS,ABB) ( Data 37)

400A ESSB 2 Supply, erection, testing and commissioning of 400A draw out type floor mounted MV cubical panel board bus bar chamber dust and vermin proof and accommodating the following d sine with Thermal Magnetic Release MCCB’s and 1 No. ACB as Incomer units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines. Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.6mm) with 4Nos. 1” X 1/2” tinned copper bus bar for 3 phases and neutral (2x 50mm x 12mm) and 2 Nos. of ear thing bus of size 1” X 1/8 tinned copper bus(25mm x 3mm) on suitable bus bar insulator(Epoxy insulator) with maximum creep age distance and supported on MS Base channel frame work of size 4”X 2”X ¼”–1Set

Incoming 1)Supply and fixing of 1 No. 400A 4 Pole MCCB, , microprocessor based, EDO/MDO breaker 433V LT ACB confirming to IS 13947–2 IEC 60947–2 with suitable capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Micro processor Based SR 18 G relay, over current trip device adjustable to LTD, STD andrelease for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, IE rules in force with inter connection and terminations as required in specification.

Outgoing 1) Supply and fixing of 250ATPN MCCB-1No 2) Supply and fixing of ,3nos. 125ATPN MCCB. Inter connecting the all LT and MCCB’s to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the MCCB’s and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1”X 1/8” Supply and fixing of LED lamp arrangements with toggle switches to the control to each phases and with rigid connection in suitable separate compartments within the cubicle by CEIG rules with , 2 sets, of supply and fixing Electronic Trivector EC,300N class 0.5 flush mounting L&T or equivalent make–ModelER300N.Supply and fixing of danger board withSiemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing andcommissioning (L&T,C&S,SIEMENS,ABB) ( Data 38)

ESSB-3( FEEDER PILLAR) & Power Panel in main esential panel, MPDB-2 Supply , Erection Testing and commissioning of 415V/50 HZ 125A Cubicle panel board as per CEA reputation with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/8 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 125A FP MCCB -1no. 63A 3P MCCB - 6nos along with necessary Rotary Handle & Spreader terminal The above panel house in suitable CRCA sheet steel box with Door & Lock & Key arrangement with suitable leg support & powder coated painting. ( Data 39)

SSB-1, AC PANEL, 250A Panel & PSB -1 from MV panel for power & pump Supply , Erection Testing and commissioning of 415V/50 HZ 250A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 250A FP MCCB -1no. 125A 3P MCCB - 4nos. ( Data 41)

PSB -4 SERVICE PANEL IN MAIN ESSENTIAL PANEL Supply , Erection Testing and commissioning of 415V/50 HZ 250A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 250A TPN MCCB -1no. 160A TPN MCCB -3nos,63A 3P MCCB -5nos ( Data 42)

POWER SWITCH BOARD 2 (FIRE PANEL) Supply, Erection Testing, and commissioning of 415V/50 HZ 250A Cubical panel board with center trimmed Chamber for the bus bar chamber and with 1” x 1/4” tin switches with 16 SWG thick CRCA sheet double chamber one side open for the 3 phases and neutral with one hole on either extreme ends for the neutral link per specification provided.1 CRCA sheet from inside of the panel board at intervals of as per IS specification 8 L&T make thermally insulated bus supports each bus rated at individual 600 mm square section bars on all four sides With two set of Digital Multifunction meter suitable for CT coil, Digital L&T make Digital Multifunction meter, suitable & I A HRC fuse links for protection loop set switch with base, top open model switch complete. 1 MCCB’s-400A on a separate in-400 amp TPN MCCB like 3ska(Phase) wit SPCC Chamber. With the following fuse size for phases: 250A TPN MCCB 1No outgoing 160A TP MCCB 2Nos. 63A TPN MCCB - 2nos Power Switch Board -1 Nos

VRF PSB-3 MPDM 1 & 2 Supply , Erection Testing and commissioning of 415V/50 HZ 125A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/8 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 125A FP MCCB -1no. 63A 3P MCCB - 4nos. ( Data 45)

EMERGENCY POWER AND CCTV PANEL FROM ESSB-2 (40KVA UPS OUTGOING PANEL)Supply , Erection Testing and commissioning of 415V/50 HZ 125A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/8 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil ,with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 125A 3P MCCB -1no,63A 4P MCCB - 3nos. 1No as outgoing in flush with wall with earth connection only. Higher End FOR POWER AND PUMP ( Data 46)

EMERGENCY LIGHTING PANEL FROM (15KV UPS) Supply , Erection Testing and commissioning of 415V/50 HZ 63A Cubicle panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1/2”x 1/8 ” tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on rear side of the panel board for earth buses and Digital L&T make Digital Multifunction meter.with suitable CT coil , with Two set of LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete. 63A FP MCCB -1no. 32ATPN MCCB -4no,.FOR Emergency Ltg

Supply and ,Erectionof Outdoor Pillar box made up of 16 SWG CRCA sheet steel ( Length 900mm x Height 1200mm x width 600mm) with door and lock & key arrangements on suitable angle iron frame support for floor /wall mounting support to house the Vertical 4 way TPN MC B Distribution board as detailed below Incoming - 63A 4P MCCB -1 no., Outgoing - 32A 3P MCB -6 nos.,( MLDB PILLAR BOX).

POWER +LIGHT (SSB -2) Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A FP MCB switch as incoming of 2 nos. 40A TP MCB, 2 nos. 32A 3P MCB, 4 nos. 32A SP MCB as outgoing on wall with earth connection only. (Higher End)

Supply & Fixing of coil earth to street light poles with 8SWG GI wire of 11.5m of length in which 10m of total length compressed in coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the Earth.

Supply and instalation of 3 KVA online UPS suitable for single phase input and single phase output, capacity - system with battery - 2 hours back up as per CEA Regulations.

Supply and installation of 15 KVA online UPS suitable for three phase input and single phase output , capacity - system with battery - 2 hours back up.

Supply and installation of 40 KVA Online UPS suitable for Three Phase input, three phase output with IGBT rectifier and isolation Transformer, to support two hours battery backup using 12V 120AH sealed maintenance free battery with MS Battery rack and interlink cables as per CEA regulations. (Quotation enclosed)

500 KVA DG

Supply, Erection, Testing, Commissioning and Handing over of 1 No 500 KVA Diesel Generator set, Diesel Generator Set with acoustic enclosure conforming to CPCB IV+ Norms and BIS Specifications with AMF.

1.ENGINE: Water cooled Diesel engine suitable for generator application with a shaft Output of 400 BHP at 1500 RPM under NTP Condition as per BSS 5514/IS 10000.

The engine shall comprise the following standard scope of supply: (Make Kirloskar/ Cummins/ Ashok Leyland/ Greaves/Equivalent)

1. Dry type Air cleaner

2. Expansion bellow

3. Radiator, Radiator fan and mounting

4. Air to air charge cooler

5. Exhaust Gas turbo charger

6. Lube oil cooler and Lube oil filter

7. Fuel filter(pre and micro

8. In-line Mono-block fuel injection pump with governor and fuel feed pump

9. Electronic governor

10. 24V Battery charging alternator

11. 24V Volt electric starter motor

12. Engine test Certificate

13. Residential Mufler

14. Fly wheel with starter ring.

ENGINE INSTRUMENTPANEL MOUNTED. Engine control panel consisting of ON/OFF/START Key Lube oil pressure guage , oil temperature gauge, high water temperature guage and electronic hour meter and RPM indicator.

SAFETY SYSTEM OF ENGINE :-The Engine shall trip for the following conditions with visual alarm device

1. Low lubricating oil pressure

2. High Water temperature

3. Vee-belt failure and over speed

4. The visual indicator should be provide for Low battery indication. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load

2. ALTERNATOR : Alternator capacity of 500 KVA/ 400 KW,AC 3 phase, 50HZ, 415/420V, 0.8P.F.4 wire self excited, self regulated designed to run at 1500 RPM under NTP conditions confirming to BS 5000/ IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate (Make: Kirloskar/ Crompton/ Greaves/ Equivlent.)

3.ACOUSTIC ENCLOSURE:- Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet.The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC Machine to maintain dimensional accuracy of hole within 0.1mm Powder coating done after seven – tank surface preparation process

of sheet metal. Canopy panel and doors shall have inside lining of FIRE RETARDANT 64 Kg/m density mineral wool of 100mm thickness as Acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt

distance shall be less than 75 DBA average or as per CPCB norms. Surface treatment – Painting: The enclosure surface shall be suitably treated for degreasing de-rusting and posphating. The canopies are passed through seven – tank

The canopies are passed through seven – tank treatment thoroughly. Additional features of canopies: Canopy fabricated on CNC machines with dimensional accuracy of 0.1 mm so as to increase its durability. Special designed supporting rips/structures are used in canopies so as to give sturdiness and to reduce the vibrations of the DG sets if any World class Cooling package:

Canopies shall have cooling package for which it can also perform at 45 degree C/ambient temperature.No grouting required on the ground, only a level surface capable of with standing the DG weight.Lifting hooks shall be provided for the acoustic enclosure, which should be

unloaded independently of the DG set. 1150.00 30250.00 The Gen set frame shall also be provided with hooks for unloading Temperature rise inside the canopy: Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well within 5-7 deg centigrade.

4. FUEL TANK : 350 liters. Removable fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connection and mechanical fuel gauge. Fuel tank can be easily removed for clearing or any maintenance.

5. BASE FRAME : The base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely

coupled, with cross members mounted on AVM. The base frame shall be have provision for mounting of acoustic enclosure on it. The supply of generator set includes loading. Unloading and transportation charges.

Supply, Installation, Testing and Commissioning of 4P, 4Wire, 630A aluminium condutor sandwich type Rising Mains with 50X6 mm (2) External aluminium earthing, Plug in Point at every 500mm, Fire Barriers at every Floor Crossing : Indoor : 25kA The product shall be based on Temp. rise & not on current density and as per techical specification and drawing. (M-2469)

630A End Feed Unit with 36kA 4P Fixed type ACB with LSIG releases (M-2480)

630A flexible joints suitable for above said sandwich type 4P aluminium rising main at end terminals including all accessories.(RYBN=1 set)

End Covers

Mounting Brackets (Recommended 1No. per 1.5 Mtrs)

630A Al T type connectivity RYBN bus for terminations

63A Tap Off Box with 25kA TPN MCCB

250A Tap Off Box with 25kA TPN MCCB

VARIABLE REFRIGERANT FLOW OUTDOOR UNITS (VRF ODU): Supply Installation,Testing & Commissioning of modular type 32 HP Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating,having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressors for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as required.The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping.The unit shall be suitable to work on 400V+/10%, 3Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required.The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Double Skin AHUs Ceiling Mounted for TFA

3400 Cfm 8.5 TR - M-2674

2200 Cfm 5.5 TR - M-2674

41.3 mm dia with 19 mm thick insulation

36.92 mm dia with 19 mm thick insulation

28.57 mm dia with 19 mm thick insulation (M-2049)

22.20 mm dia with 19 mm thick insulation (M-2050)

19.05 mm dia with 19 mm thick insulation (M-2051)

15.90 mm dia with 19 mm thick insulation (M-2052)

12.70 mm dia with 13 mm thick insulation (M-2053)

9.50 mm dia with 13 mm thick insulation (M-2054)

6.35 mm dia with 13 mm thick insulation (M-2055)

PVC CONDENSATE PIPING: Supply,installation,Testing & Commissioning of Heavy duty PVC pipes of following sizes; with 9mm thick Aluminium Foil faced Nitrile Rubber Insulation

25mm Dia

32mm Dia

40mm Dia

FACTORY MADE RECTANGULAR GI DUCTING : Supply, installation, testing and commissioning of factory made lock-forming quality rectangular GI ducting, complying with IS: 277 and having 120 GSM coating classification. The price include the cost of necessory accessories & supports (like TDF flanges, ms angle flanges, neoprene gaskets, threaded rod, corner saddles, guide vanes as per SMACNA standards, joints, labelling etc..

24 Gauge ( 0.63 mm Thick ) ( M-2006)

22 Gauge ( 0.8 mm Thick)( M-2007)

SEMI RIGID DUCT: Supply, installation, testing and balancing of Semi Rigid duct as per above specification.

150 mm Dia

SUPPLY AIR ROUND DIFFUSER: Supply, installation, testing and balancing of aluminum powder coated circular / square diffuser with collar damper as per approved shop drawings and with standard flange size.

300 mm Dia

ROUND DISC VALVE: Supply, fixing and testing of Al. powder coated Round disc Valve of 150 mm dia for Toilet Exhaust with damper.

COLLAR DAMPERS: Supply, installation, testing and commissioning of aluminium collar damper to be mounted for grilles & diffusers.

FIRE-RETARDANT CANVASS: Supply, installation, testing and commissioning of fire-retardant canvss, with GI matching flanges, with a provision of operable zip. The entire assembly shall be fabricated at factory.

SPICOT DAMPER: Supply and installation of GI Spicot Damper

150 mm Dia

VOLUME CONTROL DAMPERS: Supply, installation, testing and commissioning of Factory fabricated Rectangular shape Aero foil type Aluminium volume control dampers, 1.2-mm Al Frame, 1.0-mm, 150-mm width, with required hardware and accessories. Stiffen damper blades for stability. Include locking device to hold single-blade dampers in a fixed position without vibration & engraved marking on position of damper, as per specifications. The shafts shall be suitable to mount electric actuators, where-ever required. Dampers' flanges shall be suitable to TDF. Please refer technical specifications for complete details and scope & quote accordingly.

FIRE DAMPERS: Supply, installation, testing and commissioning of Fire dampers with fusible link, 1.5-hours fire rating, for supply ducts and return air duct where-ever crossing the space separating walls or as shown in the drawings. The damper shall be made out off 1-mm thick gal vanished Sheet metal blades, with 1.4-mm thick Galvanized sheet frame, Fusible link Fire dampers, 1-mm thick gal vanished Sheet metal blades, with 1.6-mm thick Galvanized sheet frame.

MS SUPPORT WORK: Supply, fabrication and installation of mild steel support work for support works as per the drawing , other than for duct, pipe and equipment supporting. The supports should be duly painted using two coats of primer and two coats of black enamel paint.

DUCT THERMAL INSULATION : Supply, Installation, Testing, and Commissioning of closed cell 9 mm thick Nitrile Rubber Insulation with Factroy Laminated Alu-foil and with Ultrafresh Antimicrobial protection with both side skin/smooth surface, As per ASTM G21, ASTM G22, UL-181 and E2180. Class “O” IMO A 653 (16), FM Global, UL 94 & EPA approved,with density 40-60kg /m3.Temperature of -50 to 116 Deg C and As per EN12667(DIN 52612).Thermal conductivity of 0.036 W / m K @ 0 deg C. water vapour permeability as per EN12086 (DIN 52615) , Moisture Resistance Factor >= 7000. Alu foil tape of 75mm width should be used to seal the joints with 50 mm wide 3 mm thick self adhesive tape (Black Cotton Tape not acceptable). Material shall be FM approved and preferred color shall be Black [ for duct linear=9mm thk ] Note - if the adhesive is not self adhiesive type then the glue should be used with the same manufacturer.

9mm Thick

DUCT ACOUSTIC INSULATION : Design, Manufacture, Supply, Installation, Testing, and Commissioning of Open cell Nitrile rubber for Acoustics , of Class-1 with Ultrafresh Antimicrobial protection as per ASTM G21, ASTM G22, UL-181 and E2180 , FM Global, Density 140-180Kg / m3, UL94 approved (HBF, HF 1 & HF 2) in accordance to UL 94,1996.Thermal conductivity 0.047 W / MK at 20 Deg C, Air Erosion Resistance test Confirming to ASTM Standard C 1071-05 (section 12.7). For application use Low Voc Adhesive. thickness as per specification. [ for duct linear=15mm thk ] Note - if the adhesive is not self adhiesive type then the glue should be used with the same manufacturer.

10mm Thick

UNDERDECK INSULATION : Supply, installation, testing and commissioning 13mm thickness of closed cell nitrile preformed sheet insulation without Aluminium foil for underdeck insulation with support like round insulation disc and cross steel wire. Adhesive shall be used as recommended by insulation manufacturer for applying over concrete structures.

INLINE EXHAUST FANS: Supply, Installation, testing and commissioning of factory-fabricated, assembled,tested, and finished, direct-driven circular / Rectangular fans consisting of internally lined housing, wheel, fan shaft, bearings, motor, drive assembly, with joints between sections sealed. The mounting frame will be Galvanized Steel frames of minimum 3-mm Thick with factory fabricated corner pieces.

Air Qty: 1700 CMH, ESP:15mmWC ( Toilet ,Electrical Room , Low Voltage Room)

Supply and installation of Refnet joints (Refrigerant branch kit)

Supply & Installation of cardless remote controller

Supply and laying of 3c x 1.5 sq.mm Communication and Control cabling between indoor and outdoor units with PVC conduit.

Supply and installation of 4 c x 16 sq.mm copper armoured power cable

Supply and filling of R407a refrigerant gas

Nitrogen Pressure testing ,vaccumzing the entire system

Design, Engineering, Supply, Fabrication, Erection, Testing, Commissioning and Handing over of 1No.20 persons 1360 kgs. Capacity Passenger Lift Stainless steel Gearless with MRL disable friendly vvvf drive, fire rated door & ARD as per the following specifications.

Technical specification:-

1. Number of Lifts / Type of Lift: One / Passenger

2. Load / Speed : 20 Bed cum Passanger (1360 kgs) / 1.5 Mtr. Per second

3. Drive : Micro Processor based VVVF with enhanced ride comfort and leveling functions.

4. Travel / PIT / Head Room : 15 Mtrs (Approx)

5. Number of Floors : 3 (Ground + 2 Upper Floors)

6. Number of Landing Entrances : 3

7. Number and Position of Car Entrances : 2 (Front & Rear)

8. Position of Machinery : Directly above the Lift - GEARLESS

9.Size of Lift well: 2400 x 2400 (MM Wide * MM Depth)

10. Lift Car Inside size:2000 x 1550 (MM wide * MM Depth)

11. Type or Design of Lift Car: Stainless steel neat - Hairline Finfish- 1.5 mm Thickness High quality S.S 304 Grade

12. Fireman's switch :Included.

13.Car Ceiling - Car Floor : Sleek (Small Circular Lights) - SS Hairline Finish - PVC Flooring.

14. Car Fittings. LED Lights & Regular circular) Fan 300mm sweep.

15. Type of Car Entrance Protection: Power Operated Side Opening Sliding Opening Sliding Door - Stainless Steel - Hairline Finish 1.5 mm Thickness S.S

16. Type of Landing Entrance Protection: Centre opening slinding Door - Stainless Steel - Emergency key opening at all landings.

17. Type of Landing Door Frame: Stainless Steel neat - Hairline Finish 1.5 mm Thickness S.S

18. Additional Door Spec :

19. Type Opening of Gates / Doors : 1200 x 2000 (MM Wide * MM height)

21. Electric Supply : AC 400 /440 Volts, 3 Phase, 50 Cycles

22. Steel for lift machinery: Included.

Special Inclusions:

23. Digital Position Indicator In car and landings

24. Battery Operated Emergency Light and Alarm Bell with battery and charging device.

25. Call Register Signal and Vf Door Operator

26. False Ceiling in Car.

27. Infra Red Door Screen - for full height.

28. Vandal Proof S.S Button with S.S. Cover

29. Automatic Rescue Device - consist of battery system with charges, inverter under voltage protection system etc with all accessories.

30. Minor Builders work - Included

31. Scaffolding - Included.

32. Lift License : Preparation of drawing payment of chargs to CEIG / Lift inspectorate and insurance policies if any obtaining CEIG safety Certificate as pers lift act.

33. Free Service for One Year

34.Lift duty motor of adequate capacity, electro magnetic brake with compression springs, over speed governor, phase failure and phase reversal relay, alarm bell, T guide brackets

for car and counter weight, rubber padding under winding unit, car safety gears, buffer electro mechanical door locks, emergency key, side supporting angles motor over load protection devices. Final limit switch, main suspension ropes, counter weights, lifting joist for mounting the machineries.

35. Guarantee : Guarantee for the materials & workman ship of equipments complete should be offered by the lift for a period of not less than one year.

36. Site testing in accordance with IS 14665 should be carried out at the time of handing over. (SR) (Johnson / Kone/ OTIS/Eq)

1.STANDARDS : IS 4591 2022

2.STEP : DEPTH OF STEPS NOT LESS THAN 40CM & RISE NOT MORE THAN 22CM

3.HORIZONTAL STEPS : THREE,

4.VERTICAL RISE : 5000MM,

5.HORIZONTAL SPAN : 18000MM,

6.INCLINATION : 30Degree,

7.SPEED : 0.50M/s,

8.GEAR BOX : WORM GEAR,

9.LIGHTING VOLTAGE : 240v,

10.START : STAR-DELTA,

11.POWER VOLTAGE : 415V,

11.1.FREQUENCY : 50 HZ,

12.ARRANGEMENT : PARALLEL,

13.MOTOR POWER : 5.5 KW,

14.OVER SPEED GOVERNER

15.DELIVERY IN

16.INTERMEDIATE SUPPORT : NOT REQUIRED,

17.INSTALLATION : INDOOR -

18.STANDARD INSTALLATION - 500MM EXTENSION FOR VVVF,

19.TOP : EXTENSION,

20.BOTTOM : STANDARD,

21.HANDRAIL COLOR : BLACK,

22.BALUSTRADE PANEL : TEMPERED SAFETY GLASS (10MM),

23.BALUSTRADE : VERTICAL, SLIMLINE - HIEGHT 1000MM,

23.1.BALUSTRADE PROFILE : HAIRLINE STAINLESS STEEL.

24.SKIRTING : HAIRLINE STAINLESS STEEL,

25.INNER & OUTER DECKING : HAIRLINE STAINLESS STEEL,

26.FLOAT SWITCH AT LOWER MACHINE ROOM : YES,

27.PANEL OF LANDING PLATE : ETCHED STAINLESS STEEL,

28.OIL-WATER SEPARATOR : YES,

29.STEP : DIE CAST ALIUMINIUM,GREY COLOUR

30.ZINC STEEL DRIVE CHAIN COVER : YES,

31.STEP DEMARCATION : YELLOW DEMARCATION,

32.CHAIN PROTECTION : ZINCED,

33.COMBS : DIE CAST ALUMINIUM, YELLOW PAINTING,

34.STOP BUTTON

35.BROKEN DRIVE-CHAIN CONTACT

36.SKIRTING CONTACT

37.HANDRAIL ENTRANCE CONTACT

38.BROKEN STEP-CHAIN CONTACT

39.STEP SAG CONTACT

40.PHASE MONITOR

41.ZINC STEEL FLYING WHEEL COVER

42.MOTOR OVERLOAD AND OVERHEAT CONTACT

43.COMB CONTACT :

44.STEP GAP ILLUMINATION

45.MAINTENANCE LOCKING DEVICE

46.ALARM BUZZER

47.MOTOR SPEED & ANTI-REVERSAL MONITOR

48.STEP ANTI-STATIC BRUSH

49.SAFETY BRAKE ON MAIN SHAFT

50.HANDRAIL ANTI-STATIC ROLLER

51.EARTH LEAKAGE CIRCUIT-BREAKER

52.SERVICE BRAKE RELEASE CONTACT

53.MECHANICAL ANTI-REVERSAL DEVICE

54. LED TRAFFIC LIGHT (2), FIXED ARROW SIGN-ONE EACH AT TOP & BOTTOM.

55.STEP REVERSING FENCES

56.TRAFFIC LIGHT

57.HANDRAIL BROKEN CONTACT

58.4 DRY CONTACT (UP, DN, ERROR, STOP)

59.LCD FAULT DISPLAY AT CONTROLLER

60.FIRE CONTACT

61.SKIRTING LIGHTING

62.LED COMB LIGHTING

63.SKIRTING BRUSH

64.SKIRTING BRUSH (SINGLE ROW)

65.STEP MISSING CONTACT

66.LANDING PLATE SWITCH

67.AUTO LUBRICATION SYSTEM, 68.AUTO-START : DIFFUSE / RADR SENSOR TYPE,

69.CONTROLLER LIFT DEVICE - ONE SET

70.MAINTENANCE FENCE - ONE SET

71.INSPECTION HANDLE - ONE SET

72.KEY SWITCH

73.STEP ANTI-UPTHRUST DEVICE

74.ZINC PLATED STEEL FLYWHEEL COVER

75.SWITCH BOARD BOX (IP54)

76.SOFT STOP

77.LCD FAULT DISPLAY AT MAIN CONTROLLER

78.ZINC PLATED STEEL DRIVE CHAIN COVER

79.HANDRAIL SPEED MONITOR

80.BRAKE LINING SAFETY SWITCH

81.COMB LIGHTING WITH 30 MIN. UPS

82.OUTSIDE TRUSS CLADDING : HAIRLINE STAINLESS STEEL ON LEFT, RIGHT & BOTTOM,

83.FREE SERVICE FOR ONE YEAR

84.ESCALATOR LICENSE

85.ALL DISABLED Friendly FEATURES ARE INCLUDED AS PER DIFFERENTLY ABLED ACT.

86.LICENSE : PREPARATION OF DRAWING,PAYMENT OF CHARGES TO CEIG / LIFT INSPECTORATE AND INSURANCE POLICIES IF ANY. OBTAINING CEIG SAFETY CERTIFICATE AS PER LIFT ACT etc., complete complying with standard specification and as directed by the department officers.

Supply, Erection, Testing, Commissioning and Handing over of ((From Ground Floor to First Floor) (1 no. for UP and 1 no. for DOWN)) Heavy Duty ESCALATOR as per following technical specifications :

1.STANDARDS : IS 4591 2022

2.STEP : DEPTH OF STEPS NOT LESS THAN 40CM & RISE NOT MORE THAN 22CM

3.HORIZONTAL STEPS : THREE,

4.VERTICAL RISE : 5000MM,

5.HORIZONTAL SPAN : 18000MM,

6.INCLINATION : 30Degree,

7.SPEED : 0.50M/s,

8.GEAR BOX : WORM GEAR,

9.LIGHTING VOLTAGE : 240v,

10.START : STAR-DELTA,

11.POWER VOLTAGE : 415V,

11.1.FREQUENCY : 50 HZ,

12.ARRANGEMENT : PARALLEL,

13.MOTOR POWER : 5.5 KW,

14.OVER SPEED GOVERNER

15.DELIVERY IN

16.INTERMEDIATE SUPPORT : NOT REQUIRED,

17.INSTALLATION : INDOOR -

18.STANDARD INSTALLATION - 500MM EXTENSION FOR VVVF,

19.TOP : EXTENSION,

20.BOTTOM : STANDARD,

21.HANDRAIL COLOR : BLACK,

22.BALUSTRADE PANEL : TEMPERED SAFETY GLASS (10MM),

23.BALUSTRADE : VERTICAL, SLIMLINE - HIEGHT 1000MM,

23.1.BALUSTRADE PROFILE : HAIRLINE STAINLESS STEEL.

24.SKIRTING : HAIRLINE STAINLESS STEEL,

25.INNER & OUTER DECKING : HAIRLINE STAINLESS STEEL,

26.FLOAT SWITCH AT LOWER MACHINE ROOM : YES,

27.PANEL OF LANDING PLATE : ETCHED STAINLESS STEEL,

28.OIL-WATER SEPARATOR : YES,

29.STEP : DIE CAST ALIUMINIUM,GREY COLOUR

30.ZINC STEEL DRIVE CHAIN COVER : YES,

31.STEP DEMARCATION : YELLOW DEMARCATION,

32.CHAIN PROTECTION : ZINCED,

33.COMBS : DIE CAST ALUMINIUM, YELLOW PAINTING,

34.STOP BUTTON

35.BROKEN DRIVE-CHAIN CONTACT

36.SKIRTING CONTACT

37.HANDRAIL ENTRANCE CONTACT

38.BROKEN STEP-CHAIN CONTACT

39.STEP SAG CONTACT

40.PHASE MONITOR

41.ZINC STEEL FLYING WHEEL COVER

42.MOTOR OVERLOAD AND OVERHEAT CONTACT

43.COMB CONTACT :

44.STEP GAP ILLUMINATION

45.MAINTENANCE LOCKING DEVICE

46.ALARM BUZZER

47.MOTOR SPEED & ANTI-REVERSAL MONITOR

48.STEP ANTI-STATIC BRUSH

49.SAFETY BRAKE ON MAIN SHAFT

50.HANDRAIL ANTI-STATIC ROLLER

51.EARTH LEAKAGE CIRCUIT-BREAKER

52.SERVICE BRAKE RELEASE CONTACT

53.MECHANICAL ANTI-REVERSAL DEVICE

54. LED TRAFFIC LIGHT (2), FIXED ARROW SIGN-ONE EACH AT TOP & BOTTOM.

55.STEP REVERSING FENCES

56.TRAFFIC LIGHT

57.HANDRAIL BROKEN CONTACT

58.4 DRY CONTACT (UP, DN, ERROR, STOP)

59.LCD FAULT DISPLAY AT CONTROLLER

60.FIRE CONTACT

61.SKIRTING LIGHTING

62.LED COMB LIGHTING

63.SKIRTING BRUSH

64.SKIRTING BRUSH (SINGLE ROW)

65.STEP MISSING CONTACT

66.LANDING PLATE SWITCH

67.AUTO LUBRICATION SYSTEM, 68.AUTO-START : DIFFUSE / RADR SENSOR TYPE,

69.CONTROLLER LIFT DEVICE - ONE SET

70.MAINTENANCE FENCE - ONE SET

71.INSPECTION HANDLE - ONE SET

72.KEY SWITCH

73.STEP ANTI-UPTHRUST DEVICE

74.ZINC PLATED STEEL FLYWHEEL COVER

75.SWITCH BOARD BOX (IP54)

76.SOFT STOP

77.LCD FAULT DISPLAY AT MAIN CONTROLLER

78.ZINC PLATED STEEL DRIVE CHAIN COVER

79.HANDRAIL SPEED MONITOR

80.BRAKE LINING SAFETY SWITCH

81.COMB LIGHTING WITH 30 MIN. UPS

82.OUTSIDE TRUSS CLADDING : HAIRLINE STAINLESS STEEL ON LEFT, RIGHT & BOTTOM,

83.FREE SERVICE FOR ONE YEAR

84.ESCALATOR LICENSE

85.ALL DISABLED Friendly FEATURES ARE INCLUDED AS PER DIFFERENTLY ABLED ACT.

86.LICENSE : PREPARATION OF DRAWING,PAYMENT OF CHARGES TO CEIG / LIFT INSPECTORATE AND INSURANCE POLICIES IF ANY. OBTAINING CEIG SAFETY CERTIFICATE AS PER LIFT ACT etc., complete complying with standard specification and as directed by the department officers.

Supply, installation, testing & commissioning of Smart card readers as per specification suitable for mounting on metal surface/metal frames or wooden frames wall or as required based on site conditions including all accessories

Supply, installation, testing and commissioning of Biometric - cum -Pinpad cum Proximity Reader with 3000 Users (Templates on Reader) - 2 Templates each User with Membrane Sensor for Live Finger Verification.

Supply, installation, testing and commissioning of electromagnetic Lock (fail safe type) of 600lb holding force, with built-in Door Feedback & door ajar alarm buzzer for the following type doors :

Single leaf Door- 600LB

Single leaf Door- 1200LB

Supply installation Testing Commissioning of Recessed Magnetic Door Contact for Doors with mounting accessories to complete the installation in all respects.

Supply installation, testing, commissioning of Green ABS plastic Emergency Break Glass Units.

Supply installation, testing, commissioning of Weather Proof Green ABS plastic Emergency Break Glass Units.

Supply, installation, testing and commissioning of Two Reader Control panel housed in MS Powder Coated Cabinet with Tamper Switch, complete with On- board IP / LAN port, and Built-in Web Server for Remote Log in to every controller. Also the Controller should have spare potential free contact to trip any third part system if required. - one controller shall have attendance software for admin office staffs.

Complete with power supply unit for Controllers & Magnetic Locks

Supply and installation of 4MP high resolution IP Dome Camera with 1/3" Progressive scan CMO,maximum resolution 2560x1440 HD video output,Day &Night IR Cut Filter,4MM (Angle of View 80degree)Lens or better,Low illumination,ColourVu with maximum 20fps,3D DNR & DWDR & BLC,IR range: up to 30m,Water and dust resistant (IP67).The Camera should be mounted with suitable Mounting box (IP66 Rated). Make and Model:Matrix or UNV or Nios or Hikvision/Equivalent .

Supply and installation of 4MP high resolution IP Bullet Camera( Periphery walls / Building external walls) with 1/3" Progressive scan CMO,maximum resolution 2560x1440 HD video output,Day &Night IR Cut Filter,4MM (Angle of View 80degree)Lens or better,Low illumination,ColourVu with maximum 20fps,3D DNR & DWDR & BLC,IR range: up to 30m,Water and dust resistant (IP67),Outdoor Weatherproof,PoE & standard 12VDC/24VAC power input . IEEE802.1X Security Protocol is must in all models The Camera should be mounted with suitable Mounting box (IP66 Rated). Make and Model:Matrix or UNV or Nios or Hikvision/Equivalent.

Supply and installation 2MP network IR PTZ dome camera with 1/2.8" Progressive Scan CMOS,upto 1920x1080 resolution,Pan:360°endless; Tilt: -0.1°~160°,DWDR,45X Optical Zoom,focal length 4.8 mm to 120 mm ,3D intelligent positioning function,Up to 150m IR distance,Image Compression Video Compression H.265/H.264+/ H.264 format, IP67 Protection Level with pole mounting bracket. Focus on human and vehicle classification based on deep learning .It should support analytics for number plate detection and face recognition.Full Metal housing with Mounting bracket included for Wall/Pole Mount Make and Model: Bosch / Axis / Pelco/ Honeywell /Equivalent.

Supply and installation of 24 port PoE switch with 24 10/100/1000Mbps autosensing + 4 Gigabit SFP uplinks, Automatic detection of PoE on end devices,delivers up to 15.4W power per port and up to 53W of total PoE budget and maximum distance of 250m. Make : Netgear or Cisco or D-link/Equivalent.

Supply and installation of 10 / 100/1000Mbps 8 Port Gigabyte PoE Switch with 8× Gigabit PoE ports, 2 × Gigabit SFP uplinks. Make and Model:Netgear or Cisco or D link /Equivalent.

Supply and installation of 32 Channel Network video Recorder Connectable to the third-party network camera,Support live view,playback of the connected camera,recording upto 12 Megapixels resolution, incoming and outgoing bandwidth of 320Mbps, support 2-ch HDMI at up to 4K(3840x2160) resolution and 8 SATA HDD upto 10TB for each HDD.The current status of the HDD space remaining will be displayed on a status bar on the main monitor. NVR should be operable by front panel, wireless mouse,remote control or control keyboard.(Higher End). Make and Model:Matrix or UNV or Nios or Hikvision/Equivalent.

Supply,erection and concreting of GI Pole(40 mm dia) of height 4 meters with proper concreting and masonary work and waterproof power supply box with lock and key arrangements with painting of size 300x200x100mm for fixing the outdoor cameras.At the top of the poles necessary GI sheet cover shall be provided for the protection of Cameras.

Supply and installation of 8TB Hard Disc specifically for surveillance to be fixed inside NVR with 30 days recording backup which supports SATA 6 Gb/s interface and 64MB cache optimized with AllFrame Technology. Higher End. Make and Model:Western Digital or Seagate.

Supply and installation of 55inches full HD LED TV suitable to monitor CCTV (24X7 operation),with minimum 2 Nos of HDMI port and 2 Nos of USB port with full HD resolution of 1920X1080 pixels with the required wall mount stand and connecting accessories. Make and Model:Sony or Samsung or LG.

Supply, fixing and testing of 2 KVA online UPS with DC Voltage 72V,single phase in and out and with one hour battery backup and one layer wooden/steel fabricated stand. Make and Model:Microtek or Numeric

Supply and installation of PC Hardware with a minimum specification of Intel i7 Quad Core Processor 7th Generation at mim 3.6 GHz ,12M, Intel HD Graphic 630, 6.4GT/s, 4x4 GB or more of RAM, 512GB SATA,10K RPM 3.0Gb/s Hard Drive for OS and VMS Applications Network Interface Card - 10/100/1000 MB Network Fiber Interface Card - 4 x 1Gbps in fault tolerance configuration Video Card – nVidia 2 x NVS295 Quad Monitor Graphics card to support 4 multiplexed Monitors Motherboard should support Intel as well nVidia GPU in active-active mode and both devices should be enabled.DVD-R/W Microsoft® Windows® 8.1 / 10 Pro or Higher 64 bit.

Supply and installation of fully manageable 24 x 10/100/1000 Mbps Gigabit Ethernet Layer2 switches with four 1G uplink and mininimum of 4 × 10G SFP ports and 24 - Port Patch Panel for CAT-6 Cable with Cable Management Bar mountable in 19" rack.Compatible SFP modules should be provided end to end with necessary connections whereever required. Make:Cisco or Hp or Netgear or D Link/Equivalent.

Supply,Installation ,crimping and termination of Cat 6 UTP Patch cord of 1 metre. (Higher End). Make:Legrand or D Link or Digilink or Molex/Equivalent

Supply,Installation and termination of Cat 6 UTP Patch cord of 2 metre.(Higher End). Make:D Link or Molex or Digilink or Molex/Equivalent

Supply,Installation and termination of RJ45 Cat-6 IO connector,Back box,face plate with surface mount. Higher End. Make :Dlink or ADC or Molex or Digilink or Legrand/Equivalent.

Supply and installation of IP based EPABX System configured 6Trunk line + 10 SIP Trunk + 64 Digital Extension Expandable upto 96 analog Extensions and 112 IP Port. Make: Matrix or Equivalent.

Supply and installation of Digital 24 programmable keys Desktop Telephone instrument with Backlit keypad,Directory dial key: Navigation cursor,Call history,Redial,Speaker,Call transfer,Hold option. Make and Model: Matrix or Panasonic /Equivalent

Supply and fixing of IP phone with Ringer with LED indication,Mute and Pause function. Make:Beetel or Panasonic or equivalent

Supply, fixing and testing of 1 KVA online UPS with DC Voltage 36V Power Factor ≥ 0.99 @ full load and Exide Powersafe Plus SMF battery:12v -3Nos with two hour backup. Make and Model: Microtek or Numeric or APC or equivalent

Supply and installation of 12U MS Rack for housing EPABX,NVR, switches,Jack Panel with top and Bottom Cable Entry provision along with necessary power distribution unit,cable manager,fan and Lockable Toughened Glass Door. Higher End. (For CCTV and Intercom)

Supply and installation 4U MS Rack for housing Switches with top and Bottom Cable Entry provision along with necessary power distribution unit,cable manager,fan and Lockable Toughened Glass Door.(Higher End)

Supply and installation 6U MS Rack for housing Switches with top and Bottom Cable Entry provision along with necessary power distribution unit,cable manager,fan and Lockable Toughened Glass Door. (Higher End).

Supply and run of shielded Cat 6 cable in suitable FRLS - Fire Retardant & Low Smoke (Smoke Free)ISI certified PVC pipe concealed on wall and ceiling with necessary accessories. Higher end. Make:Legrand or DLink or Finolex or Digilink or Molex/Equivalent.

Supply and laying of ISI approved 25 mm PVC rigid pipe concealed on wall and ceiling with painting of suitable colour. Make : Finolex or Dlink or equivalent.

Supply and run of indoor 6core indoor OFC cable in suitable HDPE pipe concealed on wall and ceiling with painting of suitable colour with necessary electrical accessories. Make: DLink or Finolex or Polycab/Equivalent

Supply and laying of 6 core outdoor OFC in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and fixing of single mode media converter with 12 core LIU,necessary patch cord and connectors,splicing charges. Make:D link or equivalent

Supply, installation, testing and commissioning of Riser cable consisting of multiple /50 core or solid copper conductors of 24 AWG size insulated with expanded polyethylene covered by a PVC skin and inner shielding for grounding. The core shall be covered by a layer of plastic tape and overlaid with a corrugated PVC plastic. The cable shall be as per the specifications laid down in the tender including termination and all required accessories

Supply, installation, testing and commissioning of Data converter with 24 v DC power supply-SCHNEIDER

Supply, installation, testing and commissioning of Schneider PME -EMS software FOR 50 NODES

Supply and Fixing of Cat 6A , stranded Patch cord 1 Meter - Blue for Rack side

Please Enable Macros to View BoQ information