CA NO. GE AF NO.1/GUR-68/2025-26 SPECIAL REPAIR / RENOVATION TO PRINCIPAL QUARTER AT KV NO 1 AFS SECTOR 14 GURGAON, PROVN OF LADIES TOILET IN ADMIN AREA AND OTHER MINOR WORKS AT 54 ASP UNDER GE (AF) GURGAON NO 1.

Supply and fix automatic voltage stabilizer, single phase wall mounted copper wound air cooled digital display and designed for input variation between 140V to 280V with output voltage stabilized at 230V with accuracy of + 2.5% and of capacity 4.0 KVA, Make : Vguard/Volina/Microtech.

Demolition of RCC of any descrition and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition)

M&L for RCC 1:2:4 type B-1 using (20mm graded stone agg)for chajjas complete all as specified and directed

M&L for gunniting to RCC works in column beams, slabs, chajja, facia, landing, balconies etc by removing/ dismantling of RCC (loose concrete) and cutting of steel bar including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust and supply and fixing welded steel wire mesh 75mm x75mm with 4mm dia steel wire as facies/drops and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sikka. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2 to 2.5 Kg sqcm and applying 35mm thick gunniting in cement mortar (1:2) (one part of cement and two part of ghaghar sand) using ordinary port land cement of 43 grade over wherever required, complete all as specified and directed by Engineer-in-Charge. Note:-(i)After placing the additional reinforcement all concrete surface shall be thoroughly scrubbing with. (ii)Additional reinforced TMT bars where incorporated in work and including 20mm thick cement plaster in 1:4 (iii) Work to be carried out as in patches as directed by Engr-in-charge. (iv) Rate for steel scaffolding as directed to be included in quoted rate. (v) All demolished material removed from MOD land completely.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips

M&L TMT steel bars 6mm to 8mm dia and over cut to length bent shape required, including cranking bending binding with mild steel wire (annealed) not less than 0.9mm dia quality conforming to relevant IS complete all as specified.

Taking down chowkats or frame with shutter (without taking out shutter from the frame) exceeding 1.50 sqm and n exc 4.00 sqm each all as specified and directed

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each all as specified and directed

S & F pressed steel frames of size 165 x 60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete as specified

S & F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete as specified

M & L for PCC 1:3:6 type C1 as in filling back side of pressed steel door frames

Cutting holes into or through brick walls buil in cement mortar or cement limeand making good in cement mortar 1:3 n exc half brick thick but not exe one brick thick for inserting hold fast etc

S & F 35 mm thick 2nd class Hard wood glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats

S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with if one face is covered with deco rative face veneer with lipping/frame to match

S&F polyester powder coated aluminium frame/chowkhat for window/ ventilator of section 63.5x38.1 mm of 16 guage fixed in brick masonery or conrcrete work by necessary drilling and rawl plug aggangement etc incl polyster powder coated of any colour podwer coated aluminium window & ventilator shutters bombay sliding pattern or side hung type without sash bars aluminium as per decided by Engr-in-Charge with section 44.4x44.4mm of 16 guage including necessary jointing cleats, glazing clips, rubbers packing powder coated anodised aluminium snap beading, screw, powder coated aluminium fittings such as peg stays 150mm long (1Nos), Hinges type B-21 100mm long (2Nos) suitable handle 1 Nos complete all as specified and directed by Engineer-in-Charge.Make JINDAL/ HINDAL/ INDALCO Note:- Glass and wire mesh to be paid and measured separately under appropriate item of sch A)

S&F stainless steel wire cloth with 8% nickle 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple complete all as specified and directed by Engr-in-Charge.

S & F frosted sheet glass 3.00 mm thick , ordinary quality and glazing with oil putty in squares n.exc 0.50 Sqm in each pane.

S &F Floor door stopper of aluminium alloy 150mm body and tongue, anodised, with hard drawn steel spring. Fixed in floor

S&F for Aluminium alloy, anodised sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded section of length of bolt in 200mm

S&F aluminium anodised 150 mm long tower bolt

S&F aluminium anodised 100 mm long tower bolt

S&F aluminium anodised 100 mm handle

S&F aluminium anodised 150 mm handle

S&F aluminium anodised 100 mm butt hinges type B-21

S & F 100 mm size mild steel butt hinges medium weight cold rolled and fixed with screws or welding where required

S & F mild steel 300 mm , ordinary rat rail rod pattern springs including rollar and rollar plate complete.

S&F in repair Harrison curtain rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified

S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge

S & F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge Make : RAJSHREE/SINTEX

S&F 18 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply of single side rigid laminate of approved colour and other side plain white colour fixed with SS screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s specifications complete all as specified and directed.

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs, complete all as specified and directed.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified and directed.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions complete all as specified and directed.

S&F Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required size complete all as specified and directed.

S&F Stainless Steel 304 grade Basket Cutlery of size 370X485mm premium quality complete all as specified and directed.

S&F 18/19mm thick Preliminated particle boards interior grade,preliminated one side with dacorative choice lamination & other side blancing white lamination fixed with screws to timber frame work complete all as specified.

Extra over item of Prelaminated particle board for external teak wood lipping, 6mm thick, fixed with nails suitable for 18mm thick

S&F continous (piano)hinges mild steel,bright finish or electro galvanised width of flaps (when open)in mm 30mm

S &F Hasp and staple, Alumimium anodised length 75mm length, including bolt to hinge plate and fixed with screws complete all as specified.

M&L for Second class Hard wood,plain solid straight chowkats and frames rebated on the solid, ,rounded or chamfered put together with glue pinned at joints, supplied and fitted all as specified and as directed.

Dismantling existing tanks Exc 250 lit and N exc 500 lit capacity

Dismantling existing tanks Exc 500 lit and N exc 1000 lit capacity

S & F 1000 ltrs Rotational moulded polyethylene water storage tanks three layer (cylindrical vertical with closed top) including tank nipple and 20mm float valve PTMT hoisted and fixed in position all as per specified and directed.

Taking down or up 15 mm bore galvanised iron tubing and connection including cleaning for refixing or removal to store all as specified

All as per item No 45 here in before but 20 mm bore

S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified. (Make: Tata/Jindal/Prakash (ISI marked))

S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified. (Make: Tata/Jindal/Prakash (ISI marked))

S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 25 mm complete all as specified. (Make: Tata/Jindal/Prakash (ISI marked))

Refixing only old GI tubing 15 mm bore pipe and connections in new or old position as on walls ceiling floors etc all as specified (i) Cleaning of pipe is included in ser No 4 & 5 here in before (ii) Rates quoted by the contractor deemed to be included S & F new fittings as required Make: Tata/Prakash/Jindal ISI mark

All as per serial item 50 here in before but 20 mm bore

S & F 20 mm bore stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe all as specified and as directed

Taking down cement plaster including raking out joints hacking for key and scrubbing down with water

M & L 10 mm thick rendering in CM (1:6) on vertical surfaces of brick walls finished even and smooth without using extra cement

M & L 15 mm thick rendering in CM (1:4) on vertical surfaces of brick walls finished even and smooth without using extra cement with using water proofing compound (WPC will be measured and paid separately)

M & L for rendering 5 mm thick on ceiling on fair faces of concrete surface in Cm 1:3 finished even and smooth without using extra cement all as specified

M & L for preparation of new plastered surfaces of walls and applying two coat of Oil Bound distemper of approved tint, over a coat of 3mm thick wall care putty complete all as specified.

M & L for preparation of newly plastered surfaces and applying two coats of cement base paint over coat of chack primer on walls,facia and chajja complete all as specified.

M&L for preparation of newly plastered surfacesapplying 3 coats of white washing on internal/ external ceiling complete all as specified.

M & L preparation of new wood surfaces and applying two coats of sythetic enamel paint over a coat of wood primer

All as per item No 61 here in before but on steel surfaces over a coat of red oxide

M&L for preparation of old plastered surface of ceiling and applying one coat of white wash complete all as specified and directed by Engr-in-charge

M&L preparing old distempered surfaces of wall by complete removal of existing treatment and applying two coat of oil emulsion distemper over Birla / JK wall putty 3mm thick complete all as specified and as directed.

M&L preparation old treated surface by complete removal of existing treatment of wall and applying two coat of cement base pant over a coat of primer complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete (Fe 410-W (Gde E-250) quality B)

M&L for Steel work in tubular trusses, pillars and purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 complete all as specified and as directed by Engr-in-Charge.

M&L for Mild steel plates, plain or che

quered, 5mm thick or over in thickness in available sizes Fe 410 W (Gde-E-250) quality-A complete all as specified and as directed by Engr-in-Charge.

Dismantling of plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern roor coverings all as specified and directed by Engr-in-Charge.

S&F 0.5 mm thick pre coated thick galvalume aluminium zink coated GI based corrougated steel sheeting of any colour having tansile strength of 550 MPA as in roof covering/glading to wall fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

Dismantling of cast iron drain pipe 100mm dia jointed in lead joints or cement joints and taking out of under floors if required

M&L Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation and getting out in Soft/loose soil complete all as specified and directed .

Removing excavated soil exc. 250m but n exc 500 m & depositing where directed

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil.

Cutting into existing man holes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required as 150mm dia.

Cutting into existing man holes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required as 300mm dia.

M&L Providing precast cement concrete 1:2:4 type B-1 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces chamfers, weatherings, throat- ing etc. and setting in mortar 1:4 complete with joints to match complete all as specified.

M&L Providing cement concrete 1:2:4 type B-1 in coping, chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces chamfers, weatherings, throat- ing etc.complete with joints to match complete all as specified.

M&L Providing cement concrete bed 1:3:6 type C-1 as in bed to drain pipe 300mm dia including packing under and haunching againt the sides of pipes after they are laid etc.complete with joints to match complete all as specified.

S & F 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps as directed 6 Kg/Sq cm.

S & F 300 mm dia of pipe RCC class NP2 laid and jointed complete with collars complete all as directed

S & F 110 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes as directed

S&F 75mm bore PVC(SWR) pipes single socketed, in any length fixed to walls/laid in floors/trenches all as specified and directed

S&F PVC (SWR) bend any radius with access door suitable for 75mm dia pipes.

S&F PVC SWR branch piece single 'Y' equal or unequal 110mm bore with access door.

S&F PVC SWR branch piece single 'Y' equal or unequal 75mm bore with access door.

Supply and Fix PVC (SWR) Vent cowl suitable for 110mm dia vent pipe.

Supply and Fix PVC (SWR) Vent cowl suitable for 75mm dia vent pipe.

S&F PVC floor trap,75mm outlet dia plain with grating including joining with solvent cement all as specified and directed

S&F PVC gully trap,125/110mm outlet dia including joining with solvent cement all as specified and directed

S&F Shelf of PTMT fixed with and including chrominium plated brass screws and wooden/plastic cleats (minimum weight 300gm)

S&F in repair vitreous china wash basin, white, flat back, size 550 mm x 400 mm fixed on and including cast iron cantilever bracket 32 mm dia brass waste coupling and including fixing of tap, waste fitting and union complete all as specified and as directed.

Supply and fixed in repair 15 mm dia bore pillar taps fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or “cold’ with long screwed shank and flynuts, screwed for iron pipe and fixed complete all as specified and as directed

Supply only 32mm dia waste cupling fitting brass chromium plated for basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S & F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality

S & F 15 mm chromium plated cast copper alloy bib taps with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F Brass CP kitchen sink mixer for mixing hot & cold water screwed down for iron pipe all as specified and as directed by Enginerr-in-charge.

S&F Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe all as specified and as directed by Enginerr-in-charge

S & F in repair15 mm dia bore angle Cock with Flange chromium plated fancy type with long shank & cup (concealed type) complete all as specified and as directed.

S&F kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size 915 mm X 460 mm & bowl size 410 mm X 330 mm X 160 mm complete all as specified and as directed.

S&F Brass chromium plated tubular towel rail 20 mm dia D type, 60 cm long between flanges complete all as specified and as directed.

S&F in repair Swivel shower of PTMT any colour for fixing with 15mm pipe (Minimum weight 40gms) including shower arms 15 mm size 195 mm long with bend complete all as specified.

Soap dish, vitreous China white, approximate size 160x 160x90mm

S & Fin repair vitreous China pan (pedestal pattern), excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including CI 'P' trap dia 100 mm thick complete all as specified .

S & F in repair PVC low level cistern of 10 lit capacity inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make

Dismantling floor hearth or wall tiles including cement mortar (but not backing) removing serviceable tiles to store and rubbish off the premises

S&F Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, set and jointed in neat cement slurry and pointed in colour cement as in floor over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

-Ditto- but vertical surfaces including 10 mm thick rendering in CM 1:4

M & L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished dark shed, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick plastering in CM 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement to match the shade of the slab including rubbing and polishing, including 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

M&L machine cut kota

stone slab flooring 20-25mm thick in riser of steps,skirting,dado and pillar laid over 10mm thick cement screed base1:4 laid and jointed with grey cement to match the shade of the slab including rubbing and polishing

Rounding to edge of stone slabs one edge such as steps, cooking platform and other similar situatiion

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.including 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

M&L Cement concrete type B-2, 1:2:4 (40mm graded stone aggregate) 75mm thick for sub base of floor complete all as specified and as directed.

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with gray cement and pigments including 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

S&F M.S square/circular tube M.S pipe etc conforming to IS-1161-1979 garde grade YST 240 fixed with fastener complete all as specified and directed.

M&L Galvanised Iron steel wire 4mm dia fixing to wall and pole complete all as specified and as directed.

S&F 1.25mm mild steel, plain black sheet hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required and directed.

Removing existing roof treatment and preparing surface to he entire satisfaction of Engineer-in-Charge/ GE including taking down existing plaster, cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc flushing at junction of parapets complete and removing the same to he places where directed by Engineer-in-Charge

M&L for Cutting out cracks 'V' section on existing roofs or terrace cleaning out and filling solidly with a hot mixture bitumen and clean dry sand 1:1 by weight complete all as specified and directed by Engr-in-Charge.

M&L 40mm thick cement concrete type B0, 1:2:4 (20 mm graded aggregate) as in floor/roof including waterproofing compound including finishing cement concrete using extra cement

M&L Providing cement concrete type B 1:2:4 (12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for rendering 15mm thick on fair faces with WPC of brick and concrete surface in CM 1:4 finished even and smooth without using extra cement all as specified (WPC will be measured and paid separately)

M&L apply evenly a priming coat with bituminous primer at 4 kg per 10 sqm complete all as specified and directed

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application with overlapping 150mm complete all as specified

M&L preparation of surface two coat of amuminium paint for APP membrane, over 10 cm in width or girth not otherwise described complete all as specified and as directed

Cleaning of open drains having inner girth width upto 0.60m and depth upto 1.2 mtr by removing mud, sludege silt, garbage, debries, sludge, vegitation etc and 1 mtr both side of drain also clear as vegitation and levelling the earth work and removing debrish by manually or machanically from out of MoD land complete all as specified and directed by Engr-in-Charge

Dismantling of brick work built in cement mortar including all qoins, arches, pillars, etc. complete all as specifed and as directed by Engr-in-charge.

M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specifed and as directed by Engr-in-Charge.

Cleaning of sewage lines by rodding/pumping, bamboos etc including man holes of any description by taking out night soil excreta and solid sludge and buried under 30 cm deep soil by digging suitable size of pits 100 mtr away from the site complete all as specified and as directed. Note:-1. Excavation of pit and removal of surplus soil is deemed to be included in unit rate. 2. Contractor shall arrange water for jettin, refilling to tank including lanours required to be engaged in teh work and rubbish off the sludge beyond MD land. 3. Bleaching powder to be spread over and all around of buried night soil/sludge.

Cleaning of septic tank size 6m x 4m by opening cover, pumping out sewage water and taking out accumulated nigt soil, sludge, brick bats or any other items, (both solid and liquid) through browser with Tractor and removing the same out of defence land and placing the septic tank cover on the same opending complete al as specified and directed by Engr-in-Charge. Note:- 1. Excavation of pit and removal of surplus soil is deemed to be included in unit rate. 2. Bleaching powder to be spread over and all around of buried night soil/sludge.

Cleaning of manhole exc 0.5m length but n exc 1.5 mtr deep by dewatering by machanically/manually and taking out sludge, silt, mud, brickbats etc removing the same out of defence land and placing the manhole covers on the same opening complete all as specified and directed by Engr-in-charge

Sucking out sewage water through sewage tanker from the man hole/septic tank/ soakage well in different location and disposal (5000 ltr capacity) by using high pressure super sucker machine vehicle mounted jetting cum suction unit to be capable of air lefting of dense waste/ sludge like mud slurry, small stoes, debries, grit etc from sewer lines, through vacuum mode and capable of jettig sewer lines of dia 150mm to 450mm incl skilled driver and operator for supervising of cleaning of sewage line and also required sludge/silt/mud/debries etc of out of MD land as directed by Engr-in-charge. Note:- Pumping and Loring rates are include in this item and same shall not be operated along with items 3 to 6 hereinbefore.

Checking/Cleaning of blockage of WC, WHB, Sink, Traps, Nahani Traps, soil waste pipe etc by mannual, roddingh, using wire, vaccume section as suitable and removal of waste at distance 1 Km and above and depositing of the waste in a pit burried and covered with earth and refix in same position of grating with white cement all as sper directed by Engr-in-Charge( the work has to be carried out reguler/daily basis for proper functioning of sewage system)

S&F in repair reinforced cement concrete drain Pipes 150 mm dia NP-2 , laid in trenches in foul condition, Jointed with collars in cement mortar 1:2 and tested, complete all as specified and as directed.

M&L for Pre-Cast Factory made RCC 1:1.1/2:3 (20mm Graded crushed stone aggregate) as in cover slab of manholes, septic tanks or similar articles with plain faces and set in Cement Mortar 1:4, including form work & renfoced with 8mm dia TMT steel 100mmc/c both way, complete all as specified and as directed.

M&L for Excavating over areas in soft/loose soil, n exc 1.5 m deep and getting out all as specified and as directed by Engr-in-charge.

M&L providing 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded aggregate in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for Brick work with

sub-Class ‘B’ bricks (with old size bricks), straight or curved on plan exc. 6m mean radius, built in cement mortar 1:4, complete all as specified and as directed.

M&L for preparation of new plastered surfaces on walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including necessary scaffolding all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete ,Nominal mix type B1, 1:2:4 (20mm graded aggregates) in Beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed by Engineer-in-Charge.

M&L for Reinforced cement concrete ,Nominal mix type B1, 1:2:4 (20mm graded aggregates) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed by Engineer-in-Charge.

M&L for Rough finished flat surfaces concrete Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels,antilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. all as directed by Engr-in-Charge

M&L for Rough finished flat surfaces concrete Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc. all as directed by Engr-in-Charge

M&L for glazed ceramic coloured designer concept tiles 1200x600x10mm size as in walls set and jointed in neat cement slurry over 10mm thick recuing in cement mortar (1:4) and pointed in coloured cement to match for work on vertical surface such as skirting dado etc all as specified and as directed by Engr-in-Charge.

M&L for 10 mm thick glossy finsih for parking/ path (squar / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and jointed in white/coloured cement to match over and including 10 mm thick screed bed in cement mortar in 1:4, complete all as specified and as directed by Engr-in-charge.

M&L hard core of broken stone gauge n.exc 63 mm all as specified and directed by Engr-in-Charge.

M&L for 100 mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) in floor complete all as specified and directed by Engr-in-Charge

M&L providing 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded aggregate in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L glossy chequered cement concrete tiles 300x300x25mm thick, set jointed and pointed in near cement slurry in floors with white cement and pigments in any colour machine preassed glazed , over cement screed bed 15mm thick cement motor 1:6 all as specified and as directed by Engr-in-charge.

S&F powder coated (Thickness or powder coating not less than 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

S&F powder coated (Thickness or powder coating not less than 50 micron) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engineer-in-Charge.

S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F 4.0mm thick Figured glass, pin head ty pe and glazing with oil putty in squares exc 0.5 sq. m in each pane fixing to Aluminium/Steel/wooden Sections as in Panel of Doors/Windows/Ventilator and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc. or fixed with Oil Putty, as required/ordered at Site(s), complete and fixed all as specified and as directed.

M&L for Toughned glass 12 mm as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes, lock ,handles etc required complete all as specified & directed by Engr-in-Charge .

M&L for providing precast cement concrete type B0 1:2:4 (12.5mm graded aggregate) as in louvres and jallies, 35mm thick (measured solid), including all mouldings but excluding frame (pre cast frame shall be measured separately) set in CM 1:4 complete all as specified and directed by Engr-in-Charge.

S&F CPVC water tubing 20 mm bore pipe, SDR 11 including provision of all fittings and connected completed in concealed and surface, along with primer & slovent cement for joint as per ASTM D 2564, pipe material shall be as per ASTM D 1785, fitting/ flanges shall be as per ASTM D2467 all as specified and directed by Engr-in-charge. Note : Pipe and fittings made from CPVC shall be clearly marked with manufactures name and trade mark.

S&F 60 cm long PVC connection with two nos PTMT nut and rubber washers suitable for 15mm bore GI Pipe of existing one complete all as specified and as directed by Engineer-in-Charge.

S&F of PTMT waste coupling 32mm bore of discharge (Half or full threaded) Min weight 45 gms, complete all as specified and as directed by Engineer-in-Charge.

S&F of PTMT waste pipe 32 mm bore 80 cm long complete all as specified and as directed by Engineer-in-Charge.

S&F Rotational moulded Polyethylene (HDPE) Water Storage Tank 500 LITRE Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I, including tank nipple, union and Lowering of unserviceable Water Storage Tank with Float Valve of any description complete all as specified and directed by Engineer in charge.

S&F Chrome finish Two way bib cock 15mm bore cast copper alloy complete all as per Jaquar Code No COP-CHR-041PM or equivalent complete all as specified and directed by Engr-in-Charge.

S&F Chrome finish Single lever wash basin mixer complete all as per Jaquar Code No COP-CHR-001BPM or equivalent complete all as specified and directed by Engr-in-Charge.

S&F Chrome finish angle/ stop valves 15mm bore (for iron pipe) complete all as per Jaquar Code No OPP-CHR-15053PM or equivalent complete all as specified and directed by Engr-in-Charge.

S&F one piece square model water closet floor mounted Square Commode (White) S trap - Remaless bowl with cistern for coupled wc with UF soft close slim seat cover ,hinges ,dual flush cistern fitting with back filling and fixing accessories ,size 385x650x800mm , S- trap 220mm (with conversion bend -ZPS-WHT-VB02) all as per Jaquar Code No KUS-WHT-35753S220UFSMPMZ or equivalent complete all as specified and directed by Engr-in-Charge.

S&F table top wash basin white finish with complete accessories all as per Jaquar Code No KUS-WHT-35935 or equivalent complete all as specified and directed by Engr-in-Charge.

S&F Health faucet (ABS Body) mild steel chromium plated su

itable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as per Jaquar Code No ALD-CHR-573 or equivalent complete all as specified and directed by Engr-in-Charge.

S&F 20mm Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete in all respect as specified and directed by Engr-in-Charge.

S&F 25mm Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete in all respect as specified and directed by Engr-in-Charge.

S&F stainless steel floor grating with hole or without hole all as specified and directed by Engr-in-Charge.

S&F Chrome finish Towel Ring Square of stainless steel fixed with and including Chromium plated brass screws and wooden/plastic cleats all as per Jaquar Code No CPA-CHR-1121or equivalent complete all as specified and directed by Engr-in-Charge.

S&F Chrome finish stainless steel soap dish wall mounted all as per Jaquar Code No CPA-CHR-1131 or equivalent complete all as specified and directed by Engr-in-Charge.

S&F Chrome finish stainless steel toilet paper holder wall mounted all as per Jaquar Code No CPA-CHR-1153 or equivalent complete all as specified and directed by Engr-in-Charge.

Towel rack of size is 600mm long of stainless steel fixed with and including Chromium plated brass screws and wooden/plastic cleats all as per Jaquar Code No AHS-CHR-1581H or equivalent complete all as specified and directed by Engr-in-Charge.

M&L stack clamps for 100 bore pipe as in repairs out of 50mm by 5mm flat iron and 16mm dia round iron stays incl bolt and nuts and securing end of stays to wall or roofs complete all as specified and as directed.

Per Point

S&F PVC (SWR) vent cowl for 110mm dia pipe complete all as specified by Engineer-in -Charge

S&F 110mm Bore PVC (SWR) 'P’ trap complete all as specified and directed by Engr-in-Charge.

M&L 75mm (Diameter of outlet) PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

M&L PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F 110mm Bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete 1:3:6 (20mm Graded crushed stone aggregate) Bed for drain pipes of bore 100mm including packing under and haunching against the sides of pipes after they are laid in foul condition and testing, complete all as specified and as directed.

Surface excavation, n exc 30cm deep and averaging 15cm deep getting out in soft /loose soil complete all as specified

M&L for 100mm Cement concrete type D-2, 1:4:8 (40mm graded aggregate) in foundation filling and mass concrete or under floors all as specified and directed by Engr-in-charge.

M&L for Sand filling under floors or in foundations including watering and consolidation under paver blocks.

M&L for Machine pressed precast concrete interlocking paver block any shape and size rubber moulded confirming to IS 15658-2006 of 60 mm thickness, M-35 grade with grey cement and pigments.

M & L PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in drains etc concrete complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth girth in cement concrete using extra cement etc concrete complete all as specified and as directed.

M & L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation & mass concrete complete all as specified and as directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately).

M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. Note : Work will be executed only by mechanised means/ tools.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil

M & L PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in foundation & mass concrete complete all as specified and as directed.

Supply and fix Flmae proof air cooled split unit air conditioner electric driven, single phase of capacity of 1.5 TR with controller, non CFC refrigerent complete in all respect.

Supply and fix Switch flame proof rotary type with termination box in LM6, 25 A, single pole 250V

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core

M&L laying well burnt old size bricks, sub class "B" bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection all as specified.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Taking down sub main wiring complete including fitting and fixtures, removing materials to store or keeping in safe custody and making good the disturbed surfaces of walls, floors, roof etc., all as specified and as dirfected.

Taking down carefully unserviceable DB any type/size disconnecting and making good disturbed surfaces complete all as directed

Taking down carefully unserviceable MCB TPN/SP/SPN/Isolator of any rating/size.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60 mm thick MS sheet,cover plate concealed in walls, suitable for housing the modular electrical acce

ssories as switches, socket outlets, fan regulators etc., all as specified and as directed for the following: -

(a) One light point controlled by one 6 Amps one way switch.

(b) One ceiling Fan, Exhaust Fan point controlled by one 6 Amps switch.

(c) One bell point controlled by one 6 Amps bell push switch.

(d) One 3 Pin 6 Amps socket point on the same board.

(d) One 3 Pin 6 Amps socket point on the independent board.

All as per above item No-5 but with 4.0 Sqmm cable for 16 Amp switch socket out let point on independent board including 2.5 Sqmm PVC insulated unsheathed cable multistranded with copper conductor earthing continuity conductor all as directed and specified by Engr-in-charge.

S & Fix modular switch1 way 6A, 1 module

S & Fix modular switch1 way 16A, 1 module

S & Fix socket out let 6A 2/3 on combined 2 module

S & Fix socket out let 6A/16A-2/3 pin combined 2 module

S & Fix ceiling rose surface backlite 65x50mm 3 terminals complete.

S & F modular fan step regulator 2 module 120 watt

S & Fix modular bell push 1 way 6A, 1 module

S & Fix modular bell , AC, 230 Volts, single pole

Rigid non metallic concealled PVC conduit 25 mm dia exclusive of boxes (junction & terminal) tees, bends, elbows, reducers, bell mouth, tube ends, and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified. For AF Net and communication wiring)

Sub main wiring complete with two runs of 6 sqmm single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor drawn through and including 20 mm dia non metallic rigid PVC conduit and conduit accessories ,fixed to walls / roofs / floors etc., with one run of 4.0 Sqmm single core multistranded copper conductor as earth continuity conductor, all as specified inclduing dismantling unseriveable sub main wiring including accessories. Note : Two runs of copper conducter and one run of earth copper conducter shall be measured as one length.

Sub main wiring complete with two runs of 16 sqmm single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor drawn through and including 20 mm dia non metallic rigid PVC conduit and conduit accessories ,fixed to walls / roofs / floors etc., with one run of 10.0 Sqmm single core multistranded copper conductor as earth continuity conductor, all as specified inclduing dismantling unseriveable sub main wiring including accessories. Note : Two runs of copper conducter and one run of earth copper conducter shall be measured as one length.

Supply and fixing ceiling fan 5 star rated , 1200mm sweep , 230 Volts, 50 Hz AC, complete with blades,with anti suicide down rod, set of canopyand connecting up including three core PVC insulated multi stranded copper conductor cable of size 2.5 Sqmm wire which shall be passed through PVC flexible conduit, from ceiling rose/connentor to fan of length not less than 1.0 meter complete all as specified and directed. Make - Usha/ Bajaj/ Havells

Supplying , installing, testing, commissioning exhaust fan heavy duty, 300 mm sweep, 230 Volts, AC , 50 Hz, 900 RPM with mild steel louvers and other accessories, making holes in walls to the required shape and size, grouting Mild steel bolts in walls of length not less than 125 mm and 12 mm dia. with nuts and washers, making good disturbed surfaces in cement and sand mortar 1:4, and matching exposed surfaces to match with the existing, removing dismantled brick work /rubbish to a distance not exceeding 50 M and connecting the fan to ceiling rose with 3 core copper cable of size 23/.0076 complete all as specified .

Supply and fixing LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB

Supply and fix sheet metal enclosure distribution board TPN, 4 ways , 415 Volts with 200 amps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed including taking down old MCB DB complete. , Make - ABB/ Siemens

Supply and fix Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning., 100 Amps, all as specified and as directed.

Supply and fix MCB single pole and neutral, 240 volts, 5 to 30 Amps, all as specified and as directed.

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed.

S&F 1100 volts grade heavy duty cable PVC insulated 16 sqmm multistranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm dia. Galvanised mild steel suspension wire, one twin core circular cable complete all as specified.

M & L for E-top LED post top lantern aluminium canopy, die cast aluminium body, symetric light distribution with clear acrylic diffusers Make Surya model SLEPT 30WETPP , 30 Watt

M & L for Bollard fitting Make Surya model SLEBLH10W PLUS , 10 Watt

M&L earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, burried directly in to ground ( earth pit) not less than 2.25 metres deep below GL with top edge of earth plate not less athn 1.50 m below ground level , earth plate surrounded alround with adequate quantity of charcoal dust and salt to a packed thickness of 15 cm , connected to GI lead wire of 4 mm dia. by means of nuts, bolts and washers to earth plate at one end and other end to contineous GI wire of OH lines /GOD/ lightning arrestor , checknuts of GI and protected by the GI pipe light grade 15 mm nominal bore for earth lead wire from earth plate to 1500 mm above GL with FI clamps made out of 25x3mm at 1m apart , fitted with nuts, bolts and washers and painting with two coats of synthetic enamel paint over one coat of red oxide primer; and 2.5 m long watering pipe light grade of 20 mm nominal bore ,0.63 mm thick C I funnel , wiremesh etc complete including necessary earth work and excavation in soft/loose soil , PCC 1:2:4 type B1 earth pit and Precast RCC cover 65 mm thick duly reinforced with 6 mm dia. MS round bars @ 100mm C/C both ways, earth phophrous bronze testing point, making good etc. all as specified and shown in electrisl plate of SSR Part -I.

Materials & Labour for point wiring complete with two runs of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLSH cable 1100 volts grade, single core, drawn through and including concealed PVC conduit (medium Grade) of adequate size (not less than 20mm dia) with all fittings, modular metal flush box and accessories. including one run of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLSH Cable (green colour), single core as earth continuity conductor connected to common earth dolly for light,fan and call bell point controlled by one switch and Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc.making good disturbed surfaces complete all as specified and as directed.

Materials & Labour for point wiring complete with two runs of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLSH cable 1100 volts grade, single core, drawn through and including concealed PVC conduit (medium Grade) of adequate size (not less than 20mm dia) with all fittings, modular metal flush box and accessories. including one run of 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLSH Cable (green colour), single core as earth continuity conductor connected to common earth dolly for one 5Amp Switch Socket Combination o

n independent board and Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc.making good disturbed surfaces complete all as specified and as directed.

Materials & Labour for point wiring complete with two runs of 2.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLSH cable 1100 volts grade, single core, drawn through and including concealed PVC conduit (medium Grade) of adequate size (not less than 20mm dia) with all fittings incl modular metal flush box and accessories. including one run of 2.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLSH Cable (green colour), single core as earth continuity conductor connected to common earth dolly for power Point and Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc.making good disturbed surfaces complete all as specified and as directed.

M & L for fixing only modular white cover plate with frame, 8 module

M & L for modular Socket, 6A - 2/3 pin combined 2 module

S & F MCB SPN DB 8 way , Double door, vertical type, with 200Amp rated bus bar and connecting up complete all as specified Engr-in-Charge.Make-Indoasian Cat no 811805 or equivlanet model of L&T/Havell/Legrand .

S & F MCB Single Pole of cap 6-32 Amp, C Curve 240 volts 10KA complete.Make-Indoasian Cat no 811122 to 811129 or equivlanet model of L&T/Havell/legrand (for SPN DB)

S & F MCB Single Pole Neutral C Curve 230 volts of capacity 32 Amp 10 KA complete all and specified and directed by Engr-in-Charge.Make-Indoasian Cat no 811151or equivlanet model of L&T/Havell/Legrand ( For TPN & SPN DB)

Supply and fix electric water heater, storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessoriessuch as safety valve, thermostate, NRV, connection piece etc.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm (for Toilets)

S&F in replacement Recess mounted 2X2 high effciency LED luminaires 36 Watt, CCT not less than 6500K, efficacy not less than 120lm/W with inbuilt 4PIR occupancy sensor provided in luminaire for switching as per the movement of person. LED luminaire made in CRCA sheet metal with wider light window and opal polystyrene diffuser for spotless glare-free uniform lighting for offices and modern workspace areas complete all as directed by Engr-in-charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexiblecopper conductor cable of suitable size complete

S & F in repalacement service connection 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and over all PVC sheathed of size 10 Sqmm, 2 core complete all as specified and directed by Engr-in-Charge.

M & L for cutting existing 80 mm steel tubing for alterations or additions necessarily done in position without taking down and inserting Tee of 80 x 80 x 25 mm for tapping all as specified and directed.(Tapping point shown)

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core.

Wiring for circuit/submain wiring alongwith earth wire with the 2x4.0 sq. mm + 1x4 sq. mm earth wire of FR is PVC insulated copper conductor, single core cable in surface/ recessed as required.