GE/CHM-38/2024-2025 WELCOME MAINT IN MD ACCN FOR JCOS/ORS MD ACCN IN SECTOR D and F UNDER AGE B/R-I AT CHANDIMANDIR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete all as specified and directed.

Glazed ceramic tiles, coloured in vertical surface 300mmx450mmx 7mm thick, joint free, first quality, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

Demolition of plain cement concrete in ground floor and paving n.exc 15cm thickness below or above ground level complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40m graded crushed stone aggregate) as in sub base flooring, finished even ,all as specified and directed.

40mm thick PCC 1:2:4 type B-1 (using 20m graded crushed stone aggregate) as in flooring, finished even and smooth without using extra cement complete all as specified and directed.

Non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, superior quality as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge

Non skid ceramic coloured tiles, joint free, first quality, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.18 Square metre but not exceeding 0.38 Square metre, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Baroda green marble 14 to 16mm thick, machine cut, laid over and including 10mm thick screed bed in cement mortar (1:4), bedded and jointed with grey cement slurry and pointed with grout of matching shade including moulding and all necessary cutting and machine polishing (table rubbed and polished), as in kitchen platform, step, jambs, pillars and like, complete all as specified and directed.

15mm thick rendering in cement mortar 1:4 on brick walls or concrete surface on inside wall of ventilation shaft of MAP Qtrs and finished fair and even without using extra cement, including taking down old cement plaster complete all as specified & directed. NOTE : Rates are including cost of scaffolding etc for four storey MAP Qtr Bldg

Preparation of new plastered surfaces of walls and applying two coats of cement base paint (approved colour), including necessary scaffolding complete all as specified and directed.

Supply only Integral waterproofing compound, all as specified.

Rendering 10mm thick in Cement and Sand mortar 1:6 over fair faces of brick/concrete surfaces ,finished even and smooth without using extra cement, including taking down old cement plaster complete all as specified & directed.

Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over and including a coat of primer complete all as specified and directed.

Preparation of old decorated wall surfaces and applying two coats of oil bound distemper complete all as specified and directed.

5mm thick rendering in Cement and Sand mortar 1:3 concrete surfaces as in ceiling / chajjas facia at any position finished even and smooth without using extra cement including taking down of existing plaster , complete all as specified and directed.

2mm thick birla white putty on wall surfaces complete all as specified and directed.

25mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed.

Preparation of old decorated wall surfaces and applying one coat of oil bound distemper complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

Taking down chowkats or frame n. exc. 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 Sqm and n exc 4 Square metre with shutters, without taking off shutters from the frame, complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge

Pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including filling of PCC 1:3:6 in hollow frame complete all as specified and directed.

Pressed steel frames 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including filling of PCC 1:3:6 in hollow frame complete all as specified and directed.

30mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides all as specified & directed by Engineer-in-charge.

Factory made plain framed panelled shutters, 35mm thick (with two panel) of 2nd class hard wood with lock rail and panels of 9mm thick commercial ply or 12mm thick veneered particle board with commercial veneering on both sides, duly hammer marked. The size of rail & style shall be as per IS 1003 Part-I Kiln seasoned and chemically pressure treated including a shop coat of pink primer complete all as specified & directed.

Glazed and gauged skelton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated,complete all as specified & directed.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed as in repair complete all as specified and directed.

3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

3mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes, as in repair complete all as specified and directed.

3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panesas in repair complete all as specified and directed.

Framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-290 grade E-165 complete all as specified & directed by Engineer-in-charge.

150mm long extruded aluminium alloy handles, fabricated type, complete all as specified and directed.

Mild steel sliding door bolt 300mm long, clip and bolt type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum 6 bolts and nuts, four on bolt plate and two on staple plate including necessary welding, complete all as specified and directed.

200mm aluminum anodized barrel tower bolts of extruded section, complete all as specified.

Butt hinges 100mm size, of extruded aluminum alloy with galvanised mild steel hinge pin, anodised, type B-21, complete all as specified and directed.

300mm MS ordinary rat tail rod pattern spring incl roller plate complete all as specified and directed.

Two coats of synthetic enameled paint on steel and iron surfaces over 10 cm width or girth including preparation of new surfaces complete all as specified & directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Brick work with sub class ‘B’ bricks, old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4, including dismantling of old brick complete all as specified & directed.

Repairs to leaking joints of CI pipes/ traps/ fittings etc after taking out old jointing material lead / cement, cleaning the joint thoroughly and filling new material lead / cement and sealing the joints with joint sealing compound (Dr Fixit or equivalent) and making the installation completely leak proof complete all as specified. Note : (i) The work pertains to the drain pipes/ fittings of the WC / bath of MAP quarters installed under side of the roofs. (ii) All the joints of pipes / traps / fittings of one WC / bath shall be measured as one unit and payment shall be made for each WC / bath as “Each Job”. (iii) The rates shall include for providing scaffolding etc as required.

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Reinforced cement concrete type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete all as specified and directed Note : Reinforcement and form work shall be measured and paid separately

Mild steel TMT bars 10mm dia and over ,cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Form work to flat surfaces of suspended slabs such as roof slab, floor slab, landing, shelves etc not exceeding 200mm thick, including edges in any position, rough finished surfaces, complete all as specified and directed.

Taking down shutters of any description exceeding 1Sqm but not exceeding 2sqm each including stacking at location as directed by Engineer-in-Charge for refixing in same opening(s) after rescuring or easing, adusting, welding, etc., complete all as specified and directed.

Taking down shutters of any description n.exceeding 1Sqm each including stacking at location as directed by Engineer-in-Charge for refixing in same opening(s) after rescuring or easing, adusting, welding, etc., complete all as specified and directed.

PVC (SWR) floor trap 75mm bore, plain with grating incl jointing with solvent cement, fixed as in repair complete all as specified and directed.

Wash hand basin, vitreous china, flat back, white of size 550 x 400 mm with and including angle brackets, CP waste couplng, waste pipe etc fixed as in repair complete all as specified and directed.

Vitreous china, wash down water closet pan, Pedestal pattern coloured with ‘P’ or ‘S’ trap in and, including seat cover, complete set, fixed as in repair complete all as specified and directed.

Vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe complete including trap, set with cement fixed in repair complete all as specified and directed.

Bib taps, cast copper alloy, with crutch or butterfly handle, chromium plated, fancy type, screwed down, screwed for 15mm bore iron pipe, ISI marked, fixed as in repair complete all as specified and as directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

Central hole Basin Mixer, with popup waste system with 450mm long copper pipes and brass nuts, cast copper alloy, chromium plated, screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and directed.

Chromium plated, fancy type shower rose with swivel joints 125mm dia with arm and fixing to steel pipe 15mm bore, fixed as in repairs, complete all as specified and directed

Bath mirror cabinet of size 622mm x 422mm fixed to wall with rawl plugs having arrangements to put inside toiletries, fixed as in repairs complete all as specified and directed.

Kitchen sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and CP waste coupling, overall size 915mm x 460mm x 203mm, with bowl of size 405mm x 354mm x 203mm incl fixing cantilever brackets, fixed as in repairs, complete all as specified and directed.

Plate rack made out of 1.00mm stainless steel sheet of size 750mmx 600mm with steel shelves and hanging arrangements for utensil, fixed as in repair complete all as specified and directed.

Chromium plated hand jet (health faucet) for 15mm bore pipe with 1.25 metre long flexible tube, including fixing of hook on wall, fixed in repairs, all as specified.

PVC valve less syphonic action flushing type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend for English squat pattern WC, set with concrete and making good to floor, fixed as in repair complete all as specified & directed.

PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, fixed as in repair compelte all as specified and directed.

PVC (SWR) pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, fixed as in repair compelte all as specified and directed.

75mm bore PVC (SWR) bends any radius, complete all as specified and directed.

110mm bore PVC (SWR) bends any radius ,complete all as specified and directed.

75mm bore PVC (SWR) reducer any radius, complete all as specified and directed.

110mm bore PVC (SWR) reducer any radius ,complete all as specified and directed.

75mm bore PVC (SWR) coupler any radius, complete all as specified and directed.

110mm bore PVC (SWR) coupler any radius ,complete all as specified and directed.

75 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

100 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

Steel water tubes, 15mm dia bore, medium grade, galvanized, with all standard fittings and fixed complete to walls (surface/ concealed), ceiling or laid in floors, fixed as in repair complete all as specified and directed.

Steel water tubes, 20mm dia bore, medium grade, galvanized, with all standard fittings and fixed complete to walls (surface/ concealed), ceiling or laid in floors, fixed as in reapir complete all as specified and directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) for concealed pipe etc and making good, cutting not exceeding 10cm girth complete all as specified & directed by Engineer-in-charge.

500 Litres capacity Rotational moulded polythene water storage tanks (cylindrical vertical with closed top) double layered hoisted and fixed in position including PTMT ball valve 20mm bore & PTMT tank nipple, etc, fixed as in repairs, complete all as specified and directed.

Stop valve (concealed type), cast copper alloy, chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work at any height , complete all as specified and directed.

18mm thick PVC louvers and jallies fixed in aluminium / mild steel channel frame of approved thickness, including all mouldings fitting and fixtures complete all as specified and directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) with riveted, bolted or welded attachment using Fe 290 (Gde-E- 165) complete all as specified and directed.

Three coats of white wash on ceiling surfaces including preparation of new plastered surfaces complete all as specified and directed

100mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4), fixed as in repair complete all as specified & directed

CI 75mm bore branch pieces equal or unequal or inverted (spigot socketed type or with parallel branches fitted with oval excess door), fixed as in repair complete all as specified & directed.

100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches,fixed as in repairs complete all as specified and direted.

Cast iron bends (any radius), diminishing pieces or tapers (largrer bore measured), suitable for 75 mm bore spun pipes, ISI marked, fixed as in repairs complete all as specified.

All as per item No. 87 herein before but for 100mm bore pipe

4mm thick False ceiling fibre cement board, white in colour , 595mm x 595mm in size, fire and moisture resistance, fixed with and including standard GI snap grid framing (Powder coated) and suspended not exceeding 900mm below from ceiling with 3mm dia wire including clips and misc fittings etc in pattern as approved by GE, fixed as in repair (size of panel shall be of 605 x 605mm and GI snap grid framing shall be of 1mm thick standard section i.e. channels, angles, tee etc), fixed as in repair complete all as specified and directed.

15mm dia composite (Polyethylene-Aluminium- Polyethylene (PE-AL-PE)) Composite Pressure Pipe, 1216 as per IS-15450-2004 including necessary fittings, fixed in repairs, all as specified and as directed by Engineer-in-charge. MKE : KITEC/ VECTUS/NEXGEN

20mm dia composite (Polyethylene-Aluminium- Polyethylene (PE-AL-PE)) Composite Pressure Pipe, 1620 as per IS-15450-2004 including necessary fittings, fixed in repairs, all as specified and as directed by Engineer-in-charge. MAKE : KITEC/ VECTUS/NEXGEN

Brass Socket for composite pressure pipe, 1216 as per IS 15450:2004 including necessary fittings, fixed as in repair complete all as specified and directed.

Brass elbow for composite pressure pipe, 1216 as per IS 15450:2004 including necessary fittings, fixed as in repair complete all as specified and directed.

Brass tee for composite pressure pipe, 1216 as per IS 15450:2004 including necessary fittings, fixed as in repair complete all as specified and directed.

Brass tee for composite pressure pipe, 2025 as per IS 15450:2004 including necessary fittings, fixed as in repair complete all as specified and directed.

sham enterprises (BID ID -3070997)

PARVEEN KUMAR AND SONS (BID ID -3072284)