SPECIAL REPAIRS TO BLDG No. 20 OFFICERS SQUASH COURT AND SPECIAL REPAIRS TO TOILETS AND BATHROOMS OF HOSTEL BLDG Nos. 12 TO 15 OF RMS ELGAUM UNDER GE I BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of PCC solid block masonry built in cement mortar pillars, etc. in any position below or above ground level all as specified and directed.

Demolition of reinforced cement concrete of any description and size and in any position including cutting of reinforcement as required all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area not exc 1.5 Sqm each all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise provided for all as specified and directed.

Dismantling of corrugated or semi corrugated AC sheets of any size and thickness, in roof coverings, valleys, gutters, etc. alongwith ridges all as specified and as directed.

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Taking up or down existing unserviceable 15mm bore GI tubes of any grade and making good disturbed surfaces all as specified and directed.

Taking up or down existing unserviceable 20mm bore GI tubes of any grade and making good disturbed surfaces all as specified and directed.

Cutting, chases for concealed water tubing and making good in CM 1:3 cutting not exceeding 10 cm girth in brick wall all as specified and directed.

Dismantling and breaking up drain pipes (AC, PVC, CI or RCC pipes) of size 100 mm internal dia jointed in cement mortar and taking out of trenches/ from walls if required all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5 mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

M&L for plain cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in surface channels, drains, etc. including necessary form work/ moulds all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped end etc. all as specified and directed.

M&L plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

Supply only approved integral water proofing compound all as specified and as directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, decorative teak veneered facing on both sides with lipping/ framing to match, fitted to chowkats all as specified and as directed.

M&L for aluminium frame work as in doors, partitions and windows using powder coated aluminium sections including provision of glazing clips, hinges, handles, etc including dismantling of existing aluminium joineries and making good disturbed surfaces all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

M&L aluminium anodised doors standard jindal or equivalent section size 64x38x1.4mm for frame and section size 47x25x2mm for vertical style section size 46.72x44.45x1.4mm top and central rail section size 95x44.45x2mm for bottom rail, section size 19x17.3x0.80mm for glazing clip for shutter including fabrication to required size and fixed with 5mm thick sheet glass ordinary quality in top panel and 12mm thick pre laminated particle board exterior grade pre laminated both sides with decorative choice lamination including fitting etc with floor door closer, handle, mortise lock heavy duty and door spring heavy duty complete all as specified and directed.

M&L for aluminium sliding windows (Triple track), fabricated to required size with standard aluminium anodised sections, with bottom track of size 92 x 31.75 x 1.6mm, side and top frame of size 92 x 31.75 x 1.4mm, top and bottom shutter rail of size 39x17x1.4mm, outer style of size 39 x 17 x 1.4mm, interlock style of size 39 x 27 x 1.4mm, including provision of 4mm sheet glass ordinary quality for panels including provision of all hardware fittings such as handles, locking arrangements, rubber gaskets, rollers, spring catchers etc. complete all as specified and directed.

M&L for 12mm thick figured glass, area exceeding 0.5 sqm in each pane, as in partitions including provision of necessary clamps/ stainless steel bracket, etc. complete all as specified and as directed.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on both sides reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F aluminium anodised barrel tower bolt 200mm size all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F extruded aluminium alloy handles, 150mm in size, fabricated type, anodised all as specified and directed.

S&F aluminium handle, 'D' type, anodised 150 mm in size all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F in repairs Mild steel powder coated curtain rods, 25mm dia all as specified and as directed. Make: MARVEL or equivalent

S&F in repairs fancy type brackets, mild steel with antique finish or colour with rounded fancy ends suitable for holding 25mm dia single curtain rods, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed. Make: MARVEL or equivalent

M&L for mild steel hold fast and similar small article conforming to Fe-290 Grade-E-165 all as specified and as directed.

M&L for Roof trusses (framed), trussed, purlins (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410-W Gde-E-250 quality-A all as specified and as directed.

M&L for mild steel flats as in wind ties for roof including securing bolts and necessary drilling, conforming to Fe-290 Gde E-165 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap in roof, wall etc fixed with L-type or J-type or cranked hook bolts including dismantling of existing unserviceable corrugated roofing sheets of any description and size and making good disturbed roof members all as specified and as directed.

M&L for providing roof treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Removing existing roof/ chajjas treatment of any type like plastic felt/ HP tiles of any description including taking down existing plastering/ concrete of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris to a distance exc 50m but n exc 100m

Brushing with neat cement slurry @ 3Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.3 litre per Sqm & providing APP modified water proofing membrane 4mm thick and weight not less than 4.5kg/Sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including min 10cm side/over lap & including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2kg per Sqm & on drying apply a coat of solar reflective bituminous aluminium paint at 0.1kg/sqm.

NOTE: APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. Contractor shall produce necessary test certificate of the manufacturer to the Engineer-in-charge before incorporation in the work. Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work.

S&F 8mm thick UPVC false ceiling with 300mm wide 8300 UPVC hollow profile sections of approved shade, tongued/ grooved system based sliding and interlocking type with and including GI snap grid consisting of main channels, cross channels, wall angles, etc, duly fixed with 2mm dia GI clip wires and suspended from RCC roof with GI 'L' suspenders with one end screwed to roof with GI 'L' cleat and 6mm dia fasteners etc. complete all as shown on CECZ Chennai Zone drawing No. TD-734 sheet 1/1 dated 04 Oct 2010 as specified and as directed. Make: POLYWOOD/ SINTEX/ PLASOPAN/ ELGI or any E-in-C's approved make.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring finished even and fair all as specified and directed.

M&L for coloured vitrified tiles, square or rectangular, light shade, 9 to 10mm thick, area of each tile not exc 0.36 Sqm, as in floors/ skirtings, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 6 to 7mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured matt finished ceramic tiles, edge cut, 7 to 8mm thick area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 350mm x 450mm x 7 to 8mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for 60mm thick rubber moulded machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with glossy finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for 50mm thick sand filling under paver bock flooring including watering and consolidation all as specified and as directed.

M&L for MAPLE WOOD FLOORING complete with the following specifications including taking out existing flooring of any description alongwith under frame, etc. including making good the disturbed surfaces all as specified and as directed. Notes: (a) Maple wood shall be original North American maple wood floor board. (b) The contractor shall furnish performance guarantee certificate for the maple wooden floor provided by them for 5 years from the date of completion of contract alongwith security deposit in the form of Term deposit for Rs. 15000/- for the period of 5 years from the date of completion of contract.

WEARING SURFACE: The surface boards shall be 21mm thick kiln seasoned/ treated maple hard wood, 57 to 83 mm wide, random in length, tongue and groove shaped, edges of the boards with a finger lock groove and the bottom side with air pass groove, with moisture content not more than 14%, conforming to World Squash Federation and treated with special anti-termite and water resistant lacquer.

UNDER FRAME: Under frame shall be made of commercial quality imported original Canadian pine wood runners of 70 mm x 45 mm, treated with anti-termite solution and fixed on the bottom side with 10mm thick EPDM air cushioned pads, stapled through the two wings at 300 mm x 300 mm.

INSTALLATION: A vapor barrier of 100 – 200 micron thick shall be provided on the leveled sub-floor before laying the under frame. The runners having air-cushion pads shall be provided on the vapor barrier in perfect level at 300 mm c/c in one direction. The surface boards shall be screwed to the runners through the tongue only and shall lock the screwed tongue by the groove of the adjoining boards. The ends of the boards shall be locked by inserting the wooden fingers through the edge grooves and fixed with suitable adhesive. An expansion of 8 to 10 mm to be left open between the wooden flooring and the surrounding tiled area/ walls. The Game line marking shall be provided as per WQF standards with recommended colors before applying the finish coat.

FINISHING: After installation, the floor surface shall be machine sanded in to achieve uniform level and finally finished with PU Polishing water based polyurethane lacquer.

M&L for plain cement concrete 1:3:6, type C1, (Using 20 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on soffit of roof ceiling, finished fair and even without using extra cement complete all as directed. all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for plastering in cement mortar 1:3, 15mm average thick, mixed with Dr. FIXIT POLYMER MORTAR PX (OR equivalent approved make) as recommended by the manufacturer on spalled RCC members like beams, columns, slabs, etc. all as specified and as directed. Note: Dr. FIXIT POLYMER PX shall be measured and paid separately.

Supply only Dr. FIXIT POLYMER MORTAR PX (OR equivalent approved make) all as specified.

M&L for three coats of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of white wash on old decorated surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of white wash on old decorated surfaces of walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of plastic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls over 1mm thick wall care putty including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls, pilasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pilasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces of any description n exc 10 cm width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of old painted wall/ floor surfaces over 10 cm width or girth and applying two coats of plastic emulsion paint all as specified and directed.

S&F 16mm bore CPVC pipes SDR 11 & CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable pipes of any grade and making good disturbed surfaces all as specified and directed.

S&F 20mm bore CPVC pipes SDR 11 & CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable pipes of any grade and making good disturbed surfaces all as specified and directed.

S&F 25mm bore CPVC pipes SDR 11 & CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable pipes of any grade and making good disturbed surfaces all as specified and directed.

S&F 15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F in repairs 15mm bore bib taps, brass CP, long body, fancy type, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs 15mm bore concussive push button taps, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs 15mm bore stop valves, brass chromium plated, fancy type, screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore pillar taps brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F in repairs 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Cat No. FUS 29041 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. ALD-CHR 563 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs stainless steel towel rail, 600mm log, grade 304, fixed to wall with and including stainless steel screws & plastic cleats all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F in repairs brass chromium plated perforated shower rose swivel type 80mm size suitable for fixing with 15mm bore pipe including 300mm long brass CP shower arm all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf, 12cm wide, fixed with suitable mild steel CP bracket guard and railing 60cm long all as specified and directed.

S&F in repairs liquid soap container, PTMT, minimum weight 105 gms, fixed to wall with CP screws and wooden/ plastic cleats all as specified and as directed.

S&F in repairs vitreous china squatting pan, Orissa pattern, size 580mm x 440mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap, lime concrete bedding, etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, plastic water closet seat of any colour as approved by GE, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm, excluding taps, waste chain and plug and porcelain stopper but including brackets etc complete all as specified and directed.

S&F in repairs vitreous china counter type oval wash basin, white, size 550x450mm, including vitreous china pedestal, swan neck fancy type pillar tap, waste pipe and waste fitting including 18mm thick polished premium quality granite counter of area not exceeding 1 sqm complete all as specified and directed.

S&F in repairs Vitreous China urinal, Half stall type, white, with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, connecting to (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed.

S&F in repairs PTMT urinal spreader, suitable for urinals, screwed for GI pipes or ferrules all as specified and directed.

S&F in repairs PVC flexible pipe (waste pipe), suitable for urinals all as specified and directed.

S&F in repairs 75 mm bore UPVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in repairs 110 mm bore UPVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall all as specified and directed.

S&F in repairs 110 mm bore UPVC (SWR) pipes, single socketed, in any length, with rubber ring joints, laid trenches or in floors, all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) bends any radius with access door all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) bends any radius with access door all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) vent cowl all as specified and directed.

S&F UPVC PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F in repairs PVC gratings with frame, dome type, 125 mm dia, with or without hole, minimum weight 40 grams, suitable for waste pipe connection all as specified and as directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

M&L for Salt glazed stoneware drain pipes, 150mm bore, laid in trenches and jointed as specified including demolition and breaking up of existing unserviceable SGSW/ RCC drain pipes jointed in cement mortar and taking out of demolished materials from trenches and making good disturbed surfaces all as specified and directed.

M&L for bed concrete to 150mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested including demolition of existing unserviceable bed concrete and taking out of demolished materials from trenches and making good disturbed surfaces all as specified and directed.

Taking down carefully existing point wiring of light/ fan/ bell/ 5 Amps socket/ 15 Amps socket/ 2 way light point, etc. complete of any description including fittings and fixtures such as switches, sockets, call bells, ceiling roses, pendants, holders, regulators, call bells, light fittings, etc. and making good the disturbed surfaces of walls, floors, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 2nd class HW board fixed on wall with sunmica top for mounting switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 109 but for one ceiling fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 109 but for one cal bell point controlled by one bell push.

All as described in item No. 109 but for one 05 Amps socket outlet on independent board.

All as described in item No. 109 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 109 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 4 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 4 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 4 sqmm cable, one run of 4 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F switch, piano type, 5 Amps, flush button, 230 volts, AC, one way all as specified and directed.

S&F bell push, flush type, 5 Amps, 230 volts, AC, one way all as specified and directed.

S&F switch piano flush type 15 Amps 230 volts all as specified and directed.

S&F socket outlet 5 Amps 3 and 5 pin flush type multipurpose all as specified and directed.

S&F socket outlet 15 Amps 3 and 5 pin 5 and 15 Amps flush type multipurpose all as specified and directed.

S&F PVC ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F call bell, ding dong, 230 volts AC supply all as specified and directed.

S&F in repairs, MCB DB TPN 4 Way with 200 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 8 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 4 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB TPN 63A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB DP 63A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB DP 40A 10KA 'C' series 50Hz AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 20W LED, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 10W LED, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 5W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 5W LED, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 42 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 42 W high brightness SMD LEDs including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F 15 Watts decorative surface mounted round LED downlighter with white powder coated aluminium housing, electronic driver, 15W LEDs 6000K, etc. complete with all accessories internally pre wired including provision of PVC/ wooden board with Sunmica top and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and making good disturbed false ceiling all as specified and directed. Make: HAVELLS ENDURA NEO DL SURFACE or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP65 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F in repairs wall mounted fan, 230 volts, single phase, 400mm sweep, white, with all accessories fixed to wall with all necessary brackets, bolts, nuts, etc. complete all as specified and as directed. Make: HAVELLS PLATINA Model No. FHWSWPTWHT16 or equivalent model in makes CG/ ORIENT

S&F exhaust fan, 300mm sweep, 230/240 Volts, 1350 RPM, single phase, metallic finish powder coated, with wire grid protection and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing including making circular hole of suitable in brick masonry wall and making good disturbed surfaces to match with existing surfaces all as specified as directed. Make: Havells VENTL-AIR DSP model or equivalent model in Almonard/ Crompton Greaves

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/S SANJAY B SHARMA

N K CONSTRUCTION

M/s. KIRAN M CHOUGULE

M/s.Y.N.PATIL

M/S MAHADEV M PATIL

SAGAR ENTERPRISES

M/s. N D KALING

SHRI.H.R.PATIL