ADB-WAS-(II)-03

Amount

Upgradation of ODR 27 to Shivan Majalapur Road Tq. Karanja Dist-Washim

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.(Item No. 3.30/ P.No. 12)

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 13)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 12 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead upto 1000 m

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Item No. 3.14/ P.No. 15)

Excavation for roadway in ordinary rock with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, transporting to embankment site with a lift upto 1.5 m and lead upto 1000 m, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections as per Technical Specification Clause 302.3.5

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specification Clause 202 (I) By Manual Means (B) Cement Concrete (Item No. 2.5 (B) / P.No. 11 )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.18) using crusher broken metal

Providing, laying, spreading and compacting crusher broken metal stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 21)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 26 ) Using 70 % Hand broken metal and 30 % crusher broken metal.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.( Item No. 5.2 (i) / P. No. 25)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 By Mechanical Means with paver finisher Case using Bitumen (S-65) VG-30

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.4 B / P.No. 39 )

Providing and laying of reinforced cement concrete pipe duct 300 mm across the road(new construction) extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends in cement mortar 1:6 providing a minimum fill of granular material over top and sides of RCC pipe as per IRC 98: 1997, bedded on a 0.3m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC 98:1997 and approved drawing etc complete. For single row for one utility services. (Rate as per National Highway, Nagpur CSR item no 8.29(i) page 24 )

Granular Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 Below flexible stone mat

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 45)

Providing concrete for plain cement concrete M-15 in open foundations complete as per drawing and Technical Specification Clauses 802,803,1202 and 1203 ( Item No. 11.4 (II) (i)

Providing and laying of boulder apron laid in wire crates with 4 mm dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 25 kg each as per drawing and technical specifications Clause 1301(Item No. 14.2 / P.No.57 ) Gabian wall

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 34)

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm equilateral triangle

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 vi) 800 mm x 600 mm Rectangular

Kilometre Stone.Reinforced cement concrete Kilometer Stone M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. i) Kilometer Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 40)

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Delineators: Supplying and installation of delineators (Roadway Indicators, Hazard markers, Object markers) 80 to 100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80x100mm rectangular or 75mm dia. Circular reflectorised panels at the top, buried or pressed into the ground and confirming to I.R.C. 79 and the drawings.

Upgradation of Dongargaon to Belkhed Road Tq. Karanja Dist-Washim

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 13)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 12 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead upto 1000 m

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Item No. 3.14/ P.No. 15)

Laying and spreading available soil in the subgrade on a prepared surface, pulverising, mixing the spread soil in place with rotavator with 2 per cent slaked lime having minimum 70 per cent of contents of CaO, grading with motor grader and compacting with the vibratory roller at OMC to the desired density to form a layer of improved Sub-grade as per Technical Specification Cluase 403.

Excavation for roadway in ordinary rock with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, transporting to embankment site with a lift upto 1.5 m and lead upto 1000 m, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections as per Technical Specification Clause 302.3.5

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Dewatering including diversion of stream, providing cofferdams, bunds, etc. as may be necessary for foundation and other parts of the work and bailing out water during and after excavation as required. Raft

Dewatering including diversion of stream, providing cofferdams, bunds, etc. as may be necessary for foundation and other parts of the work and bailing out water during and after excavation as required. Apron

Dewatering including diversion of stream, providing cofferdams, bunds, etc. as may be necessary for foundation and other parts of the work and bailing out water during and after excavation as required. Return

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.18) using crusher broken metal

Providing, laying, spreading and compacting crusher broken metal stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 21)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 26 ) Using 70 % Hand broken metal and 30 % crusher broken metal.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30 Waste plasic

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.( Item No. 5.2 (i) / P. No. 25)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 By Mechanical Means with paver finisher Case using Bitumen (S-65) VG-30

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and Laying Reinforced Cement Concrete Pipe NP2 as per design.Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. For 600 mm dia.

Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.4 B / P.No. 39 )

Providing and laying of reinforced cement concrete pipe duct 300 mm across the road(new construction) extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends in cement mortar 1:6 providing a minimum fill of granular material over top and sides of RCC pipe as per IRC 98: 1997, bedded on a 0.3m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC 98:1997 and approved drawing etc complete. For single row for one utility services. (Rate as per National Highway, Nagpur CSR item no 8.29(i) page 24 )

Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 (II) Rubble filling (For B.C. Soil) (Item No. 11.2 (II)/ P.No. 44 )

Filling in foundation trenches as per drawing and technical specification Clause 305.3.9.I Sand filling

Granular Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 Below flexible stone mat

Providing and laying stone pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302

Providing 90 cm thick flexible stone Mat as per Standard drawing including supplyying all materials at work site spreading and compaction etc complete ( Spec No : As directed by Engineer incharge )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 45)

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 15 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 45)

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 II. RCC Grade M 25 Slab

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203.I. P.C.C grade M 10 for raft

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204. II.P.C.C grade M 20 foundation

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 I. R.C.C grade M 20 Cap

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. II.R.C.C grade M 25 Raft slab

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204. II.P.C.C grade M 20 Abutment

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. II.R.C.C grade M 25 box return

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications M30 garde Clauses 800, 1205.4 and 1205.5 II R.C.C M 30 (Item No. 13.1 (II) / P.No. 53 )slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (b) P.V.C. pipe 100 mm dia ( Item No. 12.7 (b) / P.No. 48)

Providing Tar paper bearing of approved quality in proper size etc. complete (Rate as per PWD CSR 2017-18) (Item No.13.16 (V) / P.No. 52 )

Expansion joint with 25 mm thich bitumenous pad (Rate as per PWD CSR for 2017-18) (Item No.13.16 ( II) ( A) / P.No. 55 )

FE 500 Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in substructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 for fondation

FE500 Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 for sub structure

FE 500 Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 for sub structure

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202 for super structure

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 (Item No. 13.5 / P.No. 54 )

Providing pressure relief pipes 100 mm dia in bottom slab of box cell on a filter media base of 500 mm x 500 mm as per drawing and technical specification Clause 1205.5.7

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 (Item No. 12.9 / P.No. 48 )

Providing and laying of boulder apron laid in wire crates with 4 mm dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 25 kg each as per drawing and technical specifications Clause 1301(Item No. 14.2 / P.No.57 ) Gabian wall

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 34)

Providing and fixing in position pipe railing consisting of IS Rolled steel joist posts designation IS MB 100 (100x50) at 2.0 m interval and three rows of 50 mm dia steel pipes (light) including fixing in position on bridge deck complete as per drawing and technical specifications Clause 1208.2 (Item No. 13.8 / P.No.54 )

Painting Two Coats on New Concrete Surfaces Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm equilateral triangle

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 vi) 800 mm x 600 mm Rectangular

Kilometre Stone.Reinforced cement concrete Kilometer Stone M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. i) Kilometer Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 38)

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road delinator Supplying and installation of delinator (Roadway indicators, Hazard markers,Object markers) 80 to 100 cm high above ground level painted black and white in 15 cm wide strips , fitted with 80 x 100mm rectangular or 75mm dia. Circular reflectorised panels at the top

Upgradation of MDR 25 to Amboda road Tq Karanja, Dist Washim

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 13)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 12 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead upto 1000 m

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Item No. 3.14/ P.No. 15)

Excavation for roadway in ordinary rock with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, transporting to embankment site with a lift upto 1.5 m and lead upto 1000 m, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections as per Technical Specification Clause 302.3.5

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.18) using crusher broken metal

Providing, laying, spreading and compacting crusher broken metal stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 21)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 26 ) Using 70 % Hand broken metal and 30 % crusher broken metal.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.( Item No. 5.2 (i) / P. No. 25)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 By Mechanical Means with paver finisher Case using Bitumen (S-65) VG-30

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.4 B / P.No. 39 )

Providing and laying of reinforced cement concrete pipe duct 300 mm across the road(new construction) extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends in cement mortar 1:6 providing a minimum fill of granular material over top and sides of RCC pipe as per IRC 98: 1997, bedded on a 0.3m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC 98:1997 and approved drawing etc complete. For single row for one utility services. (Rate as per National Highway, Nagpur CSR item no 8.29(i) page 24 )

Granular Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 Below flexible stone mat

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 45)

Providing concrete for plain cement concrete M-15 in open foundations complete as per drawing and Technical Specification Clauses 802,803,1202 and 1203 ( Item No. 11.4 (II) (i)

Providing and laying of boulder apron laid in wire crates with 4 mm dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 25 kg each as per drawing and technical specifications Clause 1301(Item No. 14.2 / P.No.57 ) Gabian wall

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 34)

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm equilateral triangle

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 vi) 800 mm x 600 mm Rectangular

Kilometre Stone.Reinforced cement concrete Kilometer Stone M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. i) Kilometer Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 38)

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Delineators: Supplying and installation of delineators (Roadway Indicators, Hazard markers, Object markers) 80 to 100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80x100mm rectangular or 75mm dia. Circular reflectorised panels at the top, buried or pressed into the ground and confirming to I.R.C. 79 and the drawings.

Upgradation of Jamb to Anai road Tq Karanja, Dist Washim

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 13)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 12 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead upto 1000 m

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Item No. 3.14/ P.No. 15)

Excavation for roadway in ordinary rock with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, transporting to embankment site with a lift upto 1.5 m and lead upto 1000 m, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections as per Technical Specification Clause 302.3.5

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.18) using crusher broken metal

Providing, laying, spreading and compacting crusher broken metal stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 21)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 26 ) Using 70 % Hand broken metal and 30 % crusher broken metal.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.( Item No. 5.2 (i) / P. No. 25)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 By Mechanical Means with paver finisher Case using Bitumen (S-65) VG-30

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.4 B / P.No. 39 )

Providing and laying of reinforced cement concrete pipe duct 300 mm across the road(new construction) extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends in cement mortar 1:6 providing a minimum fill of granular material over top and sides of RCC pipe as per IRC 98: 1997, bedded on a 0.3m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC 98:1997 and approved drawing etc complete. For single row for one utility services. (Rate as per National Highway, Nagpur CSR item no 8.29(i) page 24 )

Granular Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 Below flexible stone mat

Providing 90 cm thick flexible stone Mat as per Standard drawing including supplyying all materials at work site spreading and compaction etc complete ( Spec No : As directed by Engineer incharge )

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 45)

Providing concrete for plain cement concrete M-15 in open foundations complete as per drawing and Technical Specification Clauses 802,803,1202 and 1203 ( Item No. 11.4 (II) (i)

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (b) P.V.C. pipe 100 mm dia ( Item No. 12.7 (b) / P.No. 48)

Providing Tar paper bearing of approved quality in proper size etc. complete (Rate as per PWD CSR 2017-18) (Item No.13.16 (V) / P.No. 52 )

Expansion joint with 25 mm thich bitumenous pad (Rate as per PWD CSR for 2017-18) (Item No.13.16 ( II) ( A) / P.No. 55 )

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications M25 garde Clauses 800, 1205.4 and 1205.5 II R.C.C M 25 (Item No. 13.1 (II) / P.No. 50 )slab

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 (Item No. 12.9 / P.No. 48 )

Providing and laying of boulder apron laid in wire crates with 4 mm dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 25 kg each as per drawing and technical specifications Clause 1301(Item No. 14.2 / P.No.57 ) Gabian wall

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 34)

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm equilateral triangle

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 vi) 800 mm x 600 mm Rectangular

Kilometre Stone.Reinforced cement concrete Kilometer Stone M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. i) Kilometer Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 38)

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road Delineators: Supplying and installation of delineators (Roadway Indicators, Hazard markers, Object markers) 80 to 100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80x100mm rectangular or 75mm dia. Circular reflectorised panels at the top, buried or pressed into the ground and confirming to I.R.C. 79 and the drawings.

Upgradation of ODR 25 to Kherda Karanja Wahitkhed road Tq Karanja, Dist Washim

Bill No.1: Site Clearance, Dismantling and Earth Works

Clearing and grubbing road land Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.( Rate as per SOR. It No. 2.2 (2) A )

Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.and transporting to the embankment locations with a lift upto 1.5 m and lead up to 1000 m as per Technical specification Clause 302.3 (Item No. 3.5 (II) / P.No. 13)

Compacting original ground supporting embankment Loosening, Levelling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Tables 300.1 and 300.2 for embankment construction as per Technical Specification Clause 301.4.1. (Sor 3.12)

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Table 300.1 and 300.2 as per technical specification clause 301.5 ([RATE AS PER S.O.R. Item No. 3.3 A Page no 12 ]

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead upto 1000 m

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 ([RATE AS PER S.O.R. Item No 3.4 Page no 12 A with a lead

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Item No. 3.14/ P.No. 15)

Excavation for roadway in ordinary rock with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, transporting to embankment site with a lift upto 1.5 m and lead upto 1000 m, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections as per Technical Specification Clause 302.3.5

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.I. By mechanical means in Ordinary soil (i) Upto 3 m depth

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. II) Ordinary rock (not requiring blasting) (Item No. 11.1 (II) / P.No. 46 )

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material Iv) Hard rock (blasting prohibited) Upto 3 m depth including 1.5 m depth in hard rock (Item No. 11.1 / P.No. 46)

Dewatering including diversion of stream, providing cofferdams, bunds, etc. as may be necessary for foundation and other parts of the work and bailing out water during and after excavation as required. A) For open Foudnation A1) For abutment (Item No. 11.1 A . For open fondation ( A-1) for abutment for normal dewatering

Dewatering including diversion of stream, providing cofferdams, bunds, etc. as may be necessary for foundation and other parts of the work and bailing out water during and after excavation as required. (ii) for Normal Dewatering for Return (Item No. 11.1 A . )

Bill No.2: Pavement Works (GSB, WBM, Bituminous Works) and Cement Concrete Pavement Work

Construction of Granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, etc complete as per Technical Specification Clause 401. Grading II material (Item No.4.1 (ii) /P.No.18) using crusher broken metal

Providing, laying, spreading and compacting crusher broken metal stone aggregates of specific sizes to Water Bound Macadam Grade 2 specification including spreading in uniform thickness, hand packing, rolling with three wheel roller 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405. By mechanical means (Item No. 4.8 (2) (B)/ P.No. 21)

Construction of Modified Penetration Macadam 50 mm thick over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. VG 30 bitumen (Item No. 5.5 (A) / P.No. 26 ) Using 70 % Hand broken metal and 30 % crusher broken metal.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 with [RATE AS PER S.O.R.Item no. 5.7 ) By Mechanical means (II) Bitumen (S-65) VG-30 waste plastic

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.( Item No. 5.2 (i) / P. No. 25)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type B as per Technical Specification Clause 510 By Mechanical Means with paver finisher Case using Bitumen (S-65) VG-30

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,edges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Bill No.3: Cross Drainage Structures (Culverts & Minor Bridges), Drains and Protection Works

Providing and Laying Reinforced Cement Concrete Pipe NP2 as per design.Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. For 600 mm dia.

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specification Clause 202. PCC

Providing and laying reinforced cement concrete pipe NP2 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.4 B / P.No. 39 )

Providing and laying of reinforced cement concrete pipe duct 300 mm across the road(new construction) extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends in cement mortar 1:6 providing a minimum fill of granular material over top and sides of RCC pipe as per IRC 98: 1997, bedded on a 0.3m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC 98:1997 and approved drawing etc complete. For single row for one utility services. (Rate as per National Highway, Nagpur CSR item no 8.29(i) page 24 )

Filling in foundation trenches as per drawing and technical specification Clause 305.3.9.I Sand filling

Granular Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 Below flexible stone mat

Providing and laying stone pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302

Providing 90 cm thick flexible stone Mat as per Standard drawing including supplyying all materials at work site spreading and compaction etc complete ( Spec No : As directed by Engineer incharge )

Providing and laying of boulder apron laid in wire crates with 4 mm dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm mesh (woven diagonally) including 10 per cent extra for laps and joints laid with stone boulders weighing not less than 25 kg each as per drawing and technical specifications Clause 1301

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 45)

Providing concrete for plain/reinforced concrete in foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 ( I ) P.C.C grade M 10 (I) Nominal mix (1:3:6) (Item No. 11.4 (I) (i) / P.No. 45)Annular Filling

Providing concrete for plain cement concrete M-15 in open foundations complete as per drawing and Technical Specification Clauses 802,803,1202 and 1203 ( Item No. 11.4 (II) (i)

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-15 (i) Nominal Mix 1:2.5:5 ) (Item No. 12.2 (I) (i) / P.No. 47 ) ) Bed Block

PlainPlain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 I) PCC Grade M-20 (i) Nominal Mix 1:2.:4 ) (Item No. 12.2 (I) (i) / P.No. 47 ) ) Abutment

Plain/reinforced cement concrete in superstructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (III) R.C.C grade M 25 (Item No. 12.2 (III/ P.No. 50 ) M25 cap and slab

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications M30 garde Clauses 800, 1205.4 and 1205.5 II R.C.C M 30 (Item No. 13.1 (II) / P.No. 53 )slab

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 (b) P.V.C. pipe 100 mm dia ( Item No. 12.7 (b) / P.No. 48)

Providing Tar paper bearing of approved quality in proper size etc. complete (Rate as per PWD CSR 2017-18) (Item No.13.16 (V) / P.No. 52 )

Expansion joint with 25 mm thich bitumenous pad (Rate as per PWD CSR for 2017-18) (Item No.13.16 ( II) ( A) / P.No. 55 )

FE 500 Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in substructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

FE 500 Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Supplying, fitting, and placing TMT bar reinforcement SAIL/TATA/JINDAL/RINL/ELECTRATERM or equivalent in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 (Item No. 13.5 / P.No. 54 )

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 (Item No. 12.9 / P.No. 48 )

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (B) 1000 mm dia (Item No. 9.3 B / P.No. 34)

Providing and fixing in position pipe railing consisting of IS Rolled steel joist posts designation IS MB 100 (100x50) at 2.0 m interval and three rows of 50 mm dia steel pipes (light) including fixing in position on bridge deck complete as per drawing and technical specifications Clause 1208.2 (Item No. 13.8 / P.No.54 )

Painting Two Coats on New Concrete Surfaces Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701

Bill No.4: Traffic Signs, Markings and Road Appurtenances, Road Safety & Road Furniture

Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos 75mm x 75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (Item No. 10.16 / P.No. 44 )

Providing and fixing a typical MMGSY Citizen information board as per specification provided on detailed drawing of NRRDA having frame size of 2500 x 1150 mm with 75 mm square or round steel tube for support fixed in a concrete block of 60 x 60 x 75 cm size. Information as provided in drawing of NRRDA shall be displayed on a CR/GI sheet of appropriate thickness and fixed at steel frame with 5 mm steel plate. All lettering and painting arrows border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and coloured as mentioned in detailed drawing. All sections of framed posts and steel tube shall be painted with primer and two coat of epoxy paint as per drawings. (Rate as per RD & WC Deptt. No. CMGSY-2007/CR/145/Yojana-9 dt. 4.4.2007) (Item No. 10.14 / P.No. 44)

Traffic Signs .B. Semi Reflective Traffic Signs .Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2. (v) 600 mm equilateral triangle

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 vi) 800 mm x 600 mm Rectangular

Kilometre Stone.Reinforced cement concrete Kilometer Stone M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. i) Kilometer Stone (Precast)

Reinforced cement concrete M-15 grade 200m Stone (Precast) of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. (I.No. 10.10 (ii) / P.No. 43) iii) 200m Stone (Precast)

Reinforced cement concrete M-15 grade Boundary Pillar/ Local Stone of standard design as per IRC: 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704. (Item No. 10.11 / P.No. 38)

Providing and fixing steel pipe delineators of 10 cm. in diameter and total height of 130 cm, provided with 2 strips of white retroreflective sheeting of size 5 cm. x 32.5 cm. each fixed horizontally and 2 strips of red retroreflective sheeting each having size 5 cm. x 32.5 cm. fixed horizontally at top, with M.S. round cap having diameter 11 cm. and wire mesh at top (10 guage thick) and height of wire mesh 15 cm, M.S. hold fast 6 mm thick with 35 cm. in length, fixing the delineators in C.C. 1:4:8 concrete block of size 25 cm. x 25 cm. x 45 cm. with necessary excavation etc. complete. (pwd ssr ITEM 6.16)

Providing white and colour washing to road side trees in 2 coats in 2 bands of white and one red band at centre of 30 cm height each including preparing the surface, cost of material, conveying etc. complete. (PWD SSR item 6.07)

Providing and painting with Reflit Retro Reflective Paint of approved make on old concrete/plastered or any other surfaces after applying two coats of white base coat over road furniture like Km stone, guard stone, road divider, kerb stones, parapet walls, Pipe/concrete railing, concrete sign boards, delinators and also over electric poles, road side trees, fire hydrants, crash barriers, road machineries lying on road sides or any other temporary road marking for delination purpose etc complete(including cost of labour, material, transportation and taxes etc complete) (MORT&H specification 803) (Rate as per National Highway, Nagpur CSR item no 8.8(i) B page 21 )

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete. (PWD SSR ITEM NO 218)

Providing and fixing reflective fluorescent tape on old road sign board including cleaning / scraping and painting existing board etc. complete (PWD SSR item 6.11)

Road delinator Supplying and installation of delinator (Roadway indicators, Hazard markers,Object markers) 80 to 100 cm high above ground level painted black and white in 15 cm wide strips , fitted with 80 x 100mm rectangular or 75mm dia. Circular reflectorised panels at the top