CA NO GES U 02 202324 REPAIR OF EXISTING DRAINAGE SYSTEM IN UNIT KLP ADDN ALTN OF BLDG NO NP-09 PROVN OF DHOBI GHAT WASHING POINT NEAR BLDG NO NP 46 PROVN OF TILING ENTRANCE GATE NEAR BLDG NO P62 PROVN OF SOAKAGE WELL FOR SEPTIC TANK UN

Amount

Demolition of cement concrete in ground floor and paving n exc 15 cm thickness below and above ground level complete all as specified and as directed.

Demolition of reinforced cement concrete work as in roof slabs (other than ground floors) beams staircases , landing chajjas, drop facia and similar suspended work complete all as specified and as directed.

Surface dressing not exceeding 30 cm deep and averaging 15cm in soft loose soil in road side berms including all necessary cutting / filling and finished to required size / shape complete all as specified and as directed.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M in depth for foundation complete all as specified and as directed.

Excavating over areas , n exc 1.5m deep and getting out Hard Rock complete all as specified and as directed.

M&L for anti-termite treatment of bottom and sides of excavation at the rate of 5 ltr of emulsion per square metre of surface area complete all as specified and as directed.

M&L for anti-termite treatment of the top surface of filled earth at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and as directed.

M&L for anti-termite treatment of the soil under plinth protection at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and as directed.

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per running metre including drilling and plugging holes etc. in apron. complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for waranty shall have to be furnished to Engineer-in-Charge.

Providing and injecting Antitermite Treatment of soil under existing floors using emulsion @ 1 litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand to match the existing floors complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for waranty shall have to be furnished to Engineer-in-Charge.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated soil to a distance exc 50m and n.exc 1.50 km out side defence land complete all as specified and as directed.

PCC 1:4:8 type D2 (using 40 mm crushed stone aggregates) in foundation filling and mass concrete complete all as specified and as directed.

Use & waste of form work sides of concrete foundations footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and as directed.

Reinforced cement concrete Design Mix M-25 as in foundation including rafts, footing, plinth beams, bases for columns etc complete all as specified and as directed.

Form work to sides of columns rough ,Pillars, posts, struts, chajjas, roof beams etc Square or rectangular finished surfaces of concrete complete all as specified and as directed.

Reinforced cement concrete Design Mix M-25 as in columns, pillar, pier, posts, roof beams,chajjas etc complete all as specified and as directed.

M&L for fromwork to soffits of suspended slabs such as roof slabs, landing and similar work not exc 200mm thick.complete all as specified.

Reinforced cement concrete M-25 nominal mix as in slab supported on walls , beam, and columns in floors,roofs landings, balconies etc complete all as specified and as directed.

Reinforced cement concrete (design mix) M -25 using (20mm graded aggregates) fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and retaining structures.

M&L for flat form work to fins, louvers, facia and parapet wall for rough finished surfaces of concrete complete all as specified and as directed.

M&L form work to sides and soffits of floor roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, over hangers etc also splays between floor and beam etc all as specified.for rough finished surfaces of concrete flat complete all as specified and as directed.

Mild Steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with m.s wire annealed not less than 0.9mm dia complete all as specified and as directed. (Note : Site for brick work may involve head load , contractor shall have no claim on extra labour incurred in this account)

All as per Item No 23 above but 6mm to 8mm dia complete all as specified and as directed.

Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar any description complete all as specified and as directed.

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 Metre mean radius in cement mortar 1:4 complete all as specified and as directed.

Rendering 15 mm thick in CM 1:6 on brick work and finished even and smooth without using extra cement complete all as specified and as directed.

15 mm thick rendering in two layers (10mm + 5mm) on fair faces of brick/concrete or stone surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete with water proofing compound complete complete all as specified and as directed. (WPC shall be measured separtely)

Rendering 10 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and as directed.

Applying two coat of plastic emulsion paint on new plaster surface of walls surface and (Shade approved by GE) over two coat of wall care putty with primer complete all as specified and as directed.

M&L for preparation of new plaster surfaces of wall and applying two coats of weather proof exterior emulsion paint (APEX or equivalent) over a two coat of wall care putty with coat of primer etc complete all as specified and as directed.

M & L for Preparing new ceiling surface and apply two coat of oil bound distemper over a coat of wall care putty with one coat of primer complete all as specified and as directed.

Complete removal of existing treatment of wall surface and applying two coat of plastic emulsion paint (Shade as approved by GE) over two coat of wall care putty complete all as specified and as directed.

M&L for complete removal of existing treatment (using removal machine) including preparing surfaces of wall and applying two coats of weather proof exterior emulsion paint (APEX or equivalent) over a two coat of wall care putty with a coat of Primer up to G+1 floor height etc complete all as specified and as directed.

Complete removal of existing treatment of wall applying two coat of wall care putty and two coats of oil bound distemper over a coat primers with complete all as specified and as directed.

All as per Item No 35 above but on ceiling complete all as specified and as directed.

Hard core of guage n exc. 63 mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

Sand cushioning/filling under floors or laying as per site requirement complete all as specified and as directed.

75 mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub base of floor etc complete all as specified and as directed.

50 mm thick PCC type B2 1:2:4 using 40mm graded crushed stone aggregate as in floors laid in alternate pannels finished even and smooth without using extra cement complete all as specified and as directed.

15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and as directed.

M&L for Marble tile 20 mm thick machine cut, marble slab, (Makrana white ), as in flooring, bedded jointed with grey cement slurry and pointed with white cement including cutting and polishing complete all as specified and as directed.

M&L for Marble tile 20 mm thick machine cut, marble slab, (Makrana black /green ), as in flooring, bedded jointed with grey cement slurry and pointed with white cement including cutting and polishing complete all as specified and as directed.

M&L for Marble tile 20 mm thick machine cut, marble slab, as in flooring, bedded jointed with grey cement slurry and pointed with white cement including cutting and polishing with matte finish complete all as specified and as directed.

M & L for cement concrete 1:3:6 type C-2, 75 mm thick using 20mm graded crushed stone aggregates as in plinth protection finished fair and even with using extra cement complete all as specified and as directed.

M&L for first class hard wood plain solid straight Chowkats and frames and Design main doors Pannel shutter with wrought framed on the solid rounded or chanbered put together with glue and pinned at joints including preservative treatment complete all as specified and as directed.

Supply and fixing 40 mm thick flush shutter (Both side decorative) solid core consturction with particle board core and plywood face panels on both side and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

100mm long extruded brass handle polished bright complete all as specified and as directed.

Designer brass barrel tower bots of size 100mm (ISI Marked) including screws and fixed complete all as specified and as directed.

Rendering 10 mm thick in CM 1:3 mixed with integral water proofing compound as per manufacture's instructions as in roof and chajjas, and drop facia finished the surface fair and even with out using extra cement.(Note : Supply of Integral water proofing compound will be measured and paid separately .)

Applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polythylene film. Min wt of memebrane will be 3.5 kg/sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm blinded with fine sand in dry condition @ 0.5 kg/sqm including two coats of bituminious alluminium paint complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

PCC 1:2:4 type B0 (using 12.50 graded crushed stone aggregate) for coping, corner of roof and similar work complete all as sepcified and directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed.

110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

Material and labour for ultracharged/double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour ultracharged/double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm , in skirting / dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

S&F Aluminum door closer ( aluminum extruded section) hydraullically regulated , designation No 3 , universal type , suitable for door shutters of 851mm to 1000 in width and of weight 61 to 80 kg complete all as specified and as directed.

S&F Harrison, rails drapery rod powder coated including brackets and necessary fitting complete all as specified and as directed.

M&L Rendering 10mm thick on fair faces of brick work or concrete surface in CM 1:4 on vertical surfaces/backing coat complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles of size 300x600x7mm wall tiles set and jointed in neat cement and in white/coloured cement to match with the colour of tile etc, complete all as specified and as directed.

M & L for Powder coated Aluminium frames for doors, windows, ventilators with one or more rebates annd aluminium window and ventilator shuttter frames jointing cleats for fixing and partation wall frame etc thickness of powder coating not less than 50 micron complete all as specified and as directed. Note : Powder coated aluminium coating colour is as approved by GE.

100mm thick PCC 1:4:8 Type D2 using 40 mm graded crushed stone aggregates as in foundations filling and mass concrete complete all as specified and as directed.

M&L for Coloured machine pressed vibro mechenically floated glossy finish interlocking cement paver block,any shape and size confirming to IS 15658-2006 of 60mm thickness,M-35 Grade with,topping of cement mixed with imported pigment, colour and shape shall be as approved by GE.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneelers apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete al as specified and as directed.

25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete al as specified and as directed.

Screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 laying floor finishes complete al as specified and as directed.

Dura stone tiles of size 305mmx305mmx10 mm thick as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the surface of tiles complete al as specified and as directed. ( Note :Shade/colour as approved by GE)

Providing precast cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, kneelers apex stones , bed plates, kerbs stone provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete al as specified and as directed.

Walling of random rubble,coursed,well bonded,bedded and solidly hearted built in cement mortar 1:6 complete all as specified and as directed.

All as per Item No 72 but except stone complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints,, as specified , with maximum depression on face from straight edge n. exc 40mm for lime or sand stone complete all as specified and as directed.

PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) in surafce channel and drains complete all as specified and as directed.

Demolition of brick/stone masonary built in CM. complete all as specified and as directed.

Extra for forming fair finished drain or channel 0.60cm and over inner girth in cement concrete, using extra cement, including forms moulds, mitered/stopped ends etc complete all as specified and as directed.

20mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

Providing cement concrete 1:2:4 type B-1 (20mm graded aggregate) as in coping etc complete all as specified and as directed.

Mild Steel TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Providing precast cement concrete type B1 1:2:4 using 20mm graded crused stone aggregate in landings, cover slab, shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and as directed.

Excavation in post holes (or similar holes) in any type of soil, each not exc 0.50 cum, getting out, removing surplus spoil to distance not exceeding 50 mtr and making good surface complete all as specified and as directed.

Removing surplus spoil to a distance n.exc 50m and deposited where directed at a level not exceeding 1.50 m above the starting point complete all as specified and as directed.

Rolled Mild steel work conforming to Fe 410 W (Gde E-250 Quality B) as in single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections etc complete all as specified and as directed.

Rolled mild steel conforming to Fe 410 W (Gde E-250 Quality B) in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.60mm thick crimpted/tapard at the external end scope of any colour having tensile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc complete all as specified and as directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 but except bricks all complete all as specified and as directed.

Non skid coloured ceramic tiles (square/rectengular) 8 to 9 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

10 mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles complete all as specified and as directed.

Glazed coloured ceramic tiles in dado/vertical surface (300x600mmx 7mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and as directed.

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Rendering 15mm thick in two layer (10+5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement complete all as specified and as directed.

PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete, complete all as specified and as directed.

M & L Galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and as directed.

15 mm dia

20 mm dia

15 mm bore chromium plated Bib cock with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints,Laid in trenches or in floor complete all as specified and as directed.

Extra for forming fair finished drain or channel 45cm inner girth in cement concrete, using extra cement, incl forms moulds, mitered/stopped ends etc complete all as specified and as directed.

S&F in repairs 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S&F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S&F in repairs 20mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule.

S&F fancy type chromium plated stop valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions chromium plated of size 15 mm with long shank and cup (concealed type) complete all as specified and as directed.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 2000 litres including all accessories, all as specified.

Providing precast cement concrete type 1:2:4 type B-0 in louvres and jallies 40mm thick , including all moulding but excluding frame set in cement mortor 1:4, complete all as specified and as directed.

Material and labour for plain cement concrete type D-2, 1:4:8 (Using 40mm graded stone aggregates) as in sub base complete all as specified and as directed.

Chequered coloured cement concrete tiles 30cmx30cmx(22-25)mm thick, machine pressed, factory made, set jointed and pointed in neat cement slurry, laid in floor with grey cement and pigment complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not ohterwise specifically provided for and removal and rubish of premises exc 500m but not exc 1.5 Km complete all as specified and as directed.

Material and labour for light shade vitrified ceramic coloured tiles 10mm thick (square/ rectangular) polished area of each tile n.exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed

All as per item No 107 above but on vertical surfaces over 10mm thick screed plaster in CM 1:3 complete all as specified and as directed.

Material & Labour for providing and fixing stainless steel (Grade 304) gate/railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the gate/railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc, of required size complete all as specified and as directed.

Removing excavated material exc 50 mtr but not exc 250 mtr and depositing where direct complete all as specified and as directed.

Powder coated anodised aluminium snap grid frame work of size 605 x 605mm, for false ceiling, including necessary fixing arrangement with ceiling complete all as specified and as directed.

Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

S&F Fibre cement designer ceiling board ceiling 4mm thick in 600X600mm panel (Make-everest) conforming to IS 14862 type B complete all as specified and as directed.

Taking down cement plaster from brick/concrete surfaces including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and as directed.

Material and labour for 10mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces including finishing even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of new plastered wall surfaces and applying two coats of oil bound distemper white or tinted with roller application over a coat of chalk whitening primer over 3mm thick wall care putty complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of cement based paint white or tinted over a coat of chalk whitening primer complete all as specified and as directed.

Material and labour for one coat of synthetic enamel painting on old painted steel surfaces of any description, not otherwise described over 10cm width or girth including preparation complete all as specified and as directed.

Excavating over areas, exc 1.5 m and n exc 4.5 m deep and getting out in any type of soil soft/hard complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil soft/hard complete all as specified and as directed.

M & L for loose filling with broken stone or boulders of gauge 80 to 150 mm in soakage pits complete all as specified and as directed.

M & L for flat Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work; not exceeding 200 mm thick (horizontal or sloping) complete all as specified and as directed.

Mild steel TMT bars 6mm to 8mm dia dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Reinforced cement concrete type B1 1:2:4 (using 20 mm graded aggregate) as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate for 150 mm bore pipes complete all as specified and as directed.

M & L for salt glazed stoneware drain pipes, 150 mm dia, laid in trenches and jointed complete all as specified and as directed.

Material and Labour for cutting into existing manhole for connecting new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm dia pipe complete all as specified and as directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5mm and 20mm dia), medium grade with Modular metal flush boxes thickness (1.25mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5Sq mm as earth wire stranded and conected to earth dolly complete all as specified and as directed.

All as per srl item No 128 above but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 128 but for 3 pin 5 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 128 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly.

S&F switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

All as per Srl item No 128 but for one sheet metal enclosure single pole & neutral concealed on wall independent with PVC insulated, unsheathed FRLS cable 4.0 sqmm copper multistrand condutor, alongwith PVC insulated and unsheathed FRLS cable 2.5 sqmm multi stranded copper conductor earth wire connected to common earth and earth dolly including making good the disturbed surfaces complete all as specified and as directed.

S&F Switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

S&F Socket combined 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and as directed.

S&F Socket combined 2-in-1, 3 Pin 6 & 16 Amps (Modular Type) with outer strip complete all as specified and as directed.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block complete all as specified and as directed.

S&F in replacement MCB Single Pole, 230 Volt, rating 6 to 40 Amps complete all as specified and as directed.

S&F in replacement MCB Single Pole and Neutral , 230 Volt, rating 40 to 63 Amps complete all as specified and as directed.

S&F in repair Sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 complete with one single pole MCB of any cap from 10 to 20 A complete all as specified and as directed.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S&F in Replacement fan regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED 1x40W Mini GLS E14 GEMINI wall mounting, chrome finish fixture with textured glass suitable for 10W LED Lamp. Cat Pt No - LHFOFDC1TZ1C040 complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 06 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

M/S GURU DEV BUILDERS

M/s AKHIL SHARMA

vijay constrction co

VIRINDER SINGH