REPAIR MAINTENANCE OF BOOSTER PUMPS MONOBLOCK PUMP CENTRIFUGAL PUMPS AND STARTERS IN THE AREA OF AGE U No II UNDER GE U WATER SUPPLY DELHI CANTT 10

Amount

Demolition of cement concrete unreinforced, in ground floor or pavings below or above ground level from foundation of pump sets including removal of debris from site complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregates as in foundation, sub base or mass concrete complete all as specified and as directed.

Labour for Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out electric motor of following capacities from base plate of pump set after opening the nuts, bolts etc and transporting the motor to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed . NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor.

Labour for opening the electric induction motor of following capacity including taking down/out the burnt winding wire , cleaning the slots, rewinding the motor with super enamalled copper winding wire of existing gauge ,weight etc. including all other insulating material to make it functional complete all as specified and as directed . Note:- Copper winding wire of approprioate guage will be measured in supply only

Supplying and Fixing in replacement of Motor Terminal Box of following capacity.

Supplying and Fixing in replacement of Motor Terminal Connection Plate of following capacity complete all as specified and as directed.

Supplying and Fixing in replacement of CI Sleeve on Bearing Housing of following capacity complete all as specified and as directed.

Supply and Fixing in replacement of Motor Cooling Fan as per site requirement for any size of motor made of PVC/ Aluminium complete all as specified and as directed.

Supply and Fixing in replacement of PVC cooling pipe with bush and addeptor complete all as specified and as directed.

Supply and Fixing in replacement of Brass air cock as per site requirement complete all as specified and as directed.

Labour for Disconnecting and De-coupling the Centrifugal pump of following capacity from foundation after opening /cutting the rusted nuts, bolts etc including transporting the pump to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and as directed. NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor.

Opening the centrifugal pump of following capacity, repairing the same by replacing the unserviceable spare parts including machining work and re-assembling the same in original position complete all as specified and as directed. Note:- Spare Parts required shall be measured & paid spaerately.

Supply Only in replacement of spare parts for Centrifugal pump of 5-15 HP Capacity.

CI Impeller

Pump shaft SS (AISI-410)

CI Casing wearing (Neckring)

CI interstage ring

CI stuffing box bush

CI Gland Plate

Eye bolt with nut

CI Shaft sleeve

Gasket Packing Set

Gland packing champion

Impeller key

coupling key

water liquid deflector

CI bearing cartridge DE/NDE

CI bearing plate

Coupling nut

MS Stud with nut

Labour only for Remetling of pump shaft, turning and balancing

Supply Only in replacement of spare parts for Centrifugal pump of 20-30 HP Capacity.

CI Impeller

Pump shaft SS (AISI-410)

CI Casing wearing (Neckring)

CI interstage ring

CI stuffing box bush

CI Gland Plate

Eye bolt with nut

CI Shaft sleeve

Gasket Packing Set

Gland packing champion

impeller key

coupling key

Water liquid deflector

CI bearing cartridge DE/NDE

CI bearing plate

Mechanical Seal

coupling nut

MS Stud with nut

Labour only for Remetling of pump shaft, turning and balancing

Supply Only in replacement of spare parts for Centrifugal pump of 40-50 HP Capacity.

CI Impeller

pump shaft SS (AISI-410)

CI Casing wearing (Neckring)

CI interstage ring

CI stuffing box bush

CI Gland Plate

Eye bolt with nut

CI Shaft sleeve

Gasket Packing Set

Gland packing champion

Impeller key

coupling key

water liquid deflector

CI bearing cartridge DE/NDE

CI bearing plate

Coupling nut

MS Stud with nut

Labour only for Remetling of pump shaft, turning and balancing

Supply Only in replacement of spare parts for Centrifugal pump of 60-75 HP Capacity.

CI Impeller

pump shaft SS (AISI-410)

CI Casing wearing (Neckring)

CI interstage ring

CI stuffing box bush

CI Gland Plate

Eye bolt with nut

CI Shaft sleeve

Gasket Packing Set

Gland packing champion

Impeller key

Coupling key

Water liquid deflector

CI bearing cartridge DE/NDE

CI bearing plate

Coupling nut

MS Stud with nut

Labour only for Remetling of pump shaft, turning and balancing

Supply Only in replacement of spare parts for Centrifugal pump of 90-125 HP Capacity.

CI Impeller

pump shaft SS (AISI-410)

CI Casing wearing (Neckring)

CI interstage ring

CI stuffing box bush

CI Gland Plate

eye bolt with nut

CI Shaft sleeve

Gasket Packing Set

Gland packing champion

impeller key

coupling key

water liquid deflector

CI bearing cartridge DE/NDE

CI bearing plate

coupling nut

MS Stud with nut

Labour only for Remetling of pump shaft, turning and balancing

Supply only in replacement of water seal/ Oil seal for any size of pump.

Supply only in replacement of Oring set for any size of pump

Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out monoblock pump set capacity upto 10 HP from foundation/base plate of pump set after opening the nuts, bolts etc and transporting the pump to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed . NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor.

Opening the monoblock motor and pump upto capacity 10 HP , taking down/out the burnt winding wire and cleaning the slots including rewinding the monoblock motor with super enamelled copper winding wire of existing gauge ,weight etc. and repairing the pump by replacing the unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed. Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely

Supply Only in replacement of spare parts for Monoblock pump of upto 10 HP Capacity.

CI Impeller

Mechanical Seal

water Seal

GM Shaft sleeve

gland packing sheet

water liquid deflector

impeller Nut

MS Stud with nut

Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out dewatering motor pump vertical type/ centrifugal pump set from underground sump or from base plate of capacity upto 2.5 HP after opening the nuts, bolts etc and transporting the pump to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed. Note:- Copper winding wire and spare parts of motor and pump shall be measured and paid separetely. NOTE :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor.

Opening of dewatering motor and pump/ centrifugal pump set of capacity upto 2.5 HP including taking down/out the burnt winding wire , cleaning the slots ,rewinding the motor with super enamelled copper winding wire of existing gauge ,weight etc. and repairing the pump by replacing the unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed. Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely

Supply Only in replacement of spare parts of upto 2.5 HP Capacity dewatering motor and pump/ centifugal pump set .

CI Impeller-501/503

Maintenance kit -501/503

Cable kit with float switchfluid level controller-501/503 SE

Suction plate

Plug for motor cable

Installation kit-ama porter 500

stainless steel rotor sleeve

stainless steel rotor shaft -410

Remetailing of rotor & turning/grinding

GM suction ring

Prrof jointing of submersible cable

CI suction chamber

Repairing of stamping of stator

mechanical seal set

O ring set

insulation kit

Supplying and assembling super enamelled copper winding wire of appropriate gauge suitable upto 125 HP capacity Motor

Supply and Fixing in replacement of Ball bearing No 6305 complete all as specified and as directed.

All as per serial item No 27 here-in-before but of No 6306

All as per serial item No 27 here-in-before but of No 6307

All as per serial item No 27 here-in-before but of No 6308

All as per serial item No 27 here-in-before but of No 6309

All as per serial item No 27 here-in-before but of No 6310

All as per serial item No 27 here-in-before but of No 6311

All as per serial item No 27 here-in-before but of No 6312

All as per serial item No 27 here-in-before but of No 6313

All as per serial item No 27 here-in-before but of No 6314

All as per serial item No 27 here-in-before but of No 6315

Supply and Fixing in replacement of double Ball bearing No 3307 complete all as specified and as directed.

All as per serial item No 38 here-in-before but of No 3309

All as per serial item No 38 here-in-before but of No 21309

Supply and Fixing in replacement of Roller bearing NU-313 complete all as specified and as directed.

All as per serial item No 41 here-in-before but of No NU-314

All as per serial item No 41 here-in-before but of No NU-316

All as per serial item No 41 here-in-before but of No NU-318

Supply and fixing spare tyre for coupling type as under, after taking down/out as existing at site complete all as specified and as directed.

type TC/P/011

type TC/P/013

type TC/P/014

type TC/P/015

type TC/P/017

type TC/P/018

Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 5-20 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed.

Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 25-50 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed.

Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 60-75 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed.

Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 90-125 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed.

Supply and Fixing in replacement MS base channel of size as exists including cutting, welding and making hole including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Supply and fixing bearing plate bolt of size 8 mm dia , 100 mm long after taking down/out plate as existing at site complete all as specified and as directed.

Supply and Fixing in replacement of MS foundation bolts with nuts and washers, size 20mm dia , 250 mm long complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contactor type ML-1.5, 415 Volts, 50 HZ range 25 Amps complete all as specified and as directed

Supply and fixing in replacement 3 pole power contactor type ML-2, 32 Amps, 415 Volts, 50 HZ complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contactor type ML-3, 40 Amps, 415 Volts, 50 HZ complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contactor type ML-4, 70 Amps, 415 Volts, 50 HZ complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contactor type ML-6,110 Amps, 415 Volts, 50 HZ complete all as specified and as directed.

Supply and fixing in replacement 3 pole power contactor type ML-10, 200 Amps, 415 Volts, 50 HZ complete all as specified and as directed.

Supply and fixing in replacement of Thermal Overload Relay ML-1 10 to 16 complete all as specified and as directed.

S & F in replacement of Bimetal over load replay type MN 2, relay range 14-23 Amp complete all as specified and as directed.

S & F in replacement of Bimetal over load relay type ML 2/3, relay range 20-32 Amps complete all as specified and as directed.

S & F in replacement of Bimetal over load relay type ML 2/3, relay range 28-42 Amps complete all as specified and as directed.

S & F in replacement of Bimetal over load relay type MN 5, relay range 45-75 Amps complete all as specified and as directed.

S & F in replacement of Bimetal over load relay type ML 5, relay range 66-110 Amps complete all as specified and as directed.

S & F in replacement of Bimetal over load relay type MN-12, CT operated relay range 90-150 Amps complete all as specified and as directed.

Supply and fixing in replacement Amp Meter Analog type 0 to 60 Amp of size 96 x 96 mm complete all as specified and as directed.

Supply and fixing in replacement Amp Meter Analog type 0 to 100 Amp of size 96 x 96 mm complete all as specified and as directed.

Supply and fixing in replacement Amp Meter Analog type 0 to 200 Amp of size 96 x 96 mm complete all as specified and as directed.

Supply and fixing in replacement of Indicating light RYB LED type complete all as specified and as directed.

Supply and fixing in replacement Amp Meter Digital type of size 96 x 96 mm complete all as specified and as directed.

Supply and fixing in replacement Volt Meter digital type of size 96 x 96 mm complete all as specified and as directed.

Supply and fixing in replacement FRLS PVC insulated industrial grade copper conductor wire of following size, 1100 volts complete all as specified and as directed.

4.00 sqmm, single core

6.00 sqmm, single core

10.00 sqmm, single core

16.00 sqmm, single core

25.00 sqmm, single core

35.00 sqmm, single core

Supply and fixing in replacement PVC insulated FRLS round sheathed copper conductor wire of 2.5 Sqmm, 3 core, 1100 volts complete all as specified and as directed.

Supply and fixing in replacement of Thermal contactor type MNX-18, in electric panel of motor complete all as specified and as directed.

Supply and fixing in replacement of Thermal contactor type MNX-25 in electric panel of motor complete all as specified and as directed.

Supply and fixing in replacement of Thermal contactor type MNX-32 in electric panel of motor complete all as specified and as directed.

Supply and fixing in replacement of Thermal contactor type MNX-40 in electric panel of motor complete all as specified and as directed.

Supply and Fixing in replacement Electronics Timer 3-30 seconds, Type ST100, 415 volts, complete all as specified and as directed.

Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 100 Amps with breaking capcity 16 KA , 415 volts, complete all as specified and as directed.

Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 160 Amps with breaking capcity 25 KA , 415 volts, complete all as specified and as directed.

Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 200 Amps with breaking capcity 36 KA , 415 volts, complete all as specified and as directed.

Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 250 Amps with breaking capcity 36 KA , 415 volts, complete all as specified and as directed.

Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 400 Amps with breaking capcity 50 KA , 415 volts, complete all as specified and as directed.

Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 630 Amps with breaking capcity 50 KA , 415 volts, complete all as specified and as directed.

Supply and fixing in replacement of Submersible panel board MUG 6 starter type suitable upto 10 HP

Supply and fixing in replacement of fully automatic star delta starter type with sheet metal encloser ML-1.5

Supply and fixing in replacement of fully automatic star delta starter type with sheet metal encloser

Supply and fixing in replacement of fully automatic star delta starter type with sheet metal encloser ML-4

Supply and fixing in replacement of fully automatic star delta starter type with sheet metal encloser ML-6

Supply and Fixing in replacement Automatic phase sequence correctot suitable for 51-75 HP with sheet metal encloser and indicator lamp output/input, suitable for 3 Phase electric motor with Automatically protection against single phaseing voltage, unbalanced and low/High voltage with time delay

Supply and Fixing in replacement Automatic phase sequence correctot suitable for 76-100 HP with sheet metal encloser and indicator lamp output/input, suitable for 3 Phase electric motor with Automatically protection against single phaseing voltage, unbalanced and low/High voltage with time delay.

Supply and fixing in repair copper terminals lugs ring type medium duty for following items :-

An amount of Rs 194551.00 shall be deducted from BOQ on account of schedule of credit

AMIT BROTHERS

S S CONSTRUCTION

Rahul Enterprises

VINAY ENTERPRISES

B.R. Enterprises