REPAIR TO PLASTER, TILING, PLUMBING WORK, PARAPET WALL, FALSE CEILING, WALL PANELING, CHEQUERED TILES, INTERLOCKING TILES AND CONNECTED WORKS TO CERTAIN BLDG OF ZONE A UNDER AOR OF AGE B/R-V OF GE (N) BATHINDA AT BATHINDA MIL STN

Amount

SCHEDULE 'A' B/R Works

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for plastering 15mm thick on internal surface at any story or any height in cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 5mm thick in cement mortar (1:3) on any face of ceiling, finished fair and even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparing newly plastered or concrete surface of ceiling by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash complete all as specified & directed by Engineer-in- charge

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down with using broom/sand papering or by any other means, and preparing the surfaces smooth by applying white cement based putty to make the surface even and smooth by using sander machine (with provision of dust sucking) upto entire satisfaction of Engineer-in-charge, and after preparing the surfaces applying two coats of oil emulsion distemper (washable), as approved tint/colour by using paint roller brush complete all as specified and as directed by Engineer-in-Charge.

Demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for vitrified ceramic coloured tiles (dark shade, jointless) 8 to 10 mm thick square or rectangular area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (dark shade, jointless) 8 to 10 mm thick square or rectangular area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Glazed ceramic coloured tiles of size 350mmx 250mm / 450mmX 350mm// 450mmX 300mm, 7mm to 8mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic coloured tiles 7 to 8mm thick square or rectangular area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Glazed ceramic coloured tiles of size 300mmx 200mm, 7mm to 8mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Taking up or down existing galvanised steel water/KITEC tubing (GI pipe) 15mm bore including fitting/connection from wall/ceiling/floor/concealed etc. complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as directed ) and making good disturbed surfaces of walls including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair vitreous China squatting pan 'Orissa' pattern white of size 580mmx440mm with integral foot rests (excluding flushing cistern, flush pipe above floor and trap), including demolation of tile, PCC, taking out old WC, taking out lime concrete filling and after fixing new WC re filling lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, including fixing PVC flush pipe upto finished floor level, joints of flush pipe and trap make leakproof and testing before filling concrete and including all other connected work as required upto entire satisfaction of Engineer-in-charge complete all as specified and as directed by Engineer-in- charge. (NOTE : Tile work with screed shall be measured and paid separately under appropriate item of this schedule.

Supply & fixing in repair vitreous china wash down water closet pan (pedestal pattern, EWC) white colour (excluding flushing cistern and flush pipe) including connection to drain and to flushing pipe anti syphonage etc., including plastic water closet seat with cover (white clour) closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device including stainless steel chromium plated jet spray with 01 mtr long PVC pipe with CP connector and necessary nut bolts and with necessary CP screws and plug for fixing WC complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair vitreous china wash basin, white, flat back of size 550mm x 400mm, including 32mm chromium plated waste coupling and PVC waste pipe including bracket and cutting for and pinning in end of bracket or erecting, complete all as specified and as directed by Engineer-in-Charge. (Note :- Pillar tap if required in replacement, shall be measured & paid separately under appropriate item of BOQ.)

Supply & fixing in repair 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair bib tap cast copper alloy, chromium plated with crutch or butterfly handle with capstan head, wall flange, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply & fixing in repair concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock shall be as given in SSR or in relevant IS.

Supply & fixing in repair stop valve/angle valve cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply & fixing in repair pillar tap cast copper alloy with capstan head, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts screwed for iron pipe or for brass ferrule 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS

Supply & fixing in repair grating doom 100mm dia PTMT (Min weight 25 grms) complete, all as specified & directed by Engineer-in-charge.

Supply & fixing in repair cromium plated shower rose 125mm size, with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in repair stainless steel sink made out of 1.00mm thick sheet, kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar to dwarf wall or fixing with cast iron cantilever brackets and connecting union to waste pipe; overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair stainless steel sink with drainage board made out of 1.00mm thick sheet , kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar to dwarf wall or fixing cast iron cantilever brackets and connecting union to waste pipe; overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm including taking down existing chinaware sink complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair CP waste fittings brass chromium plated for sink 40mm dia with long screws sinks and fly nuts, flange end bedded in red led cement and other in fixed, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair 40mm bore pipe Low density polyethylene pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in repair 32mm bore pipe Low density polyethylene pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in repair brass chromium plated tubular towel rail 20mm dia 'D' type, 600mm long between flanges fixed to plug , bracket with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair chromium plated glass corner (corse) size 300mm x 300mm, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair CP grating, square/rounded, 100mm size of (minimum weight 100 gms), complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply & fixing in repair 600 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply & fixing in repair chromium plated brass WHB mixer fancy type swan neck long nose screwed down high pressure with or without lettered hot and cold and flynuts 15mm dia, complete all as specified & directed by Engineer-in-charge.

Supply & fixing in repair fancy type wall mixture of brass, chromium plated 3 in 1 system with hot and cold arrangement, with provision for both hand shower & overhead shower with & including hand shower (health faucet) ABS body including 8mm dia flexible tube 1 metre long & wall hook, complete all as specified & directed by Engineer-in-charge.

Supply & fixing in repair jet spray with 1 metre PVC tube (stainless steel), chromium plated for vitreous china padestal pattern water closet, complete all as specified & directed by Engineer-in-charge.

Supply & fixing in repair hand shower (health faucet) ABS body including 1 meter long 8mm dia flexible tube and including wall hook including taking down old any type shower complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in repair Toilet Roll Holder with Stainless Steel Flap, fixed on wall with chromium plated brass screws and PVC plug complete, all as specified and as directed by Engineer-in-charge.

Supply & fixing in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints for drain or rain water fixed along walls with stack clamps made out of FI 50x5mm and 16mm dia round iron stay (interval of 1m) including nut bolt and PCC work, including dismantling/taking down old pipe complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints for drain or rain water fixed along walls with stack clamps made out of FI 50x5mm and 16mm dia round iron stay (interval of 1m) including nut bolt and PCC work, including dismantling/taking down old pipe complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair PVC (SWR) bends (any radius) suitable for 75mm bore pipe fixed to walls or laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair PVC (SWR) bends (any radius) suitable for 110mm bore pipe fixed to walls or laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair PVC (SWR) floor trap suitable for 75/110mm bore pipe, plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair brass CP bottle trap (with internal partition) 32mm bore with 250mm and 190mm long wall connection pipe, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair chromium plated glass shelf of size 22", complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair PVC bath cabinet made from hard thermosetting material with mirror, white/ivory colour, 400mm x 500mm size, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair chromium plated soap dish holder, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair plastic water closet seat cover (white colour) closed pattern with flat bottom/recessed bottom and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by Engineer-in- charge.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position including making inlet and out let connection and including supply & fixing of 20mm bore dia ball brass valve, high pressure with polythene float and flynut, including dismantling/taking down of existing unserviceable PVC water storage tanks of any description complete all as specified and as directed by Engineer-in-charge.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 1000 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position including making inlet and out let connection and including supply & fixing of 20mm bore dia ball brass valve, high pressure with polythene float and flynut, including dismantling/taking down of existing unserviceable PVC water storage tanks of any description complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in repair gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and removing from site complete all as specified and as directed by Engineer-in- charge.

Taking down shutters only of any description area not exceeding 1.0 sqm each and removing from site complete all as specified and as directed by Engineer-in- charge.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by Engineer-in- charge.

Supply and fixing factory made 105 x 60mm pressed steel frames, thickness of sheet 1.25mm for doors with one or more rebates including supply and fixing necessary lugs and lock strike plate, etc. , including fixing butt hinges suitable Nos as directed for each leaf, ncluding making good disturbed wall surface (brick and plastering work) complete all as specified and as directed by Engineer-in- charge. Note : - (i) Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only.

Supply and fixing factory made 125 x 60mm pressed steel frames, thickness of sheet 1.25mm for doors with one or more rebates including supply and fixing necessary lugs and lock strike plate, etc. , including fixing butt hinges suitable Nos as directed for each leaf, ncluding making good disturbed wall surface (brick and plastering work) complete all as specified and as directed by Engineer-in- charge. Note : - (i) Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only.

Material and labour for PCC (1:3:6) type C-1, using 20 mm graded aggregated as in back filling of chowkhats and for filling in block of hold fast complete all as specified and as directed by Engineer-in-Charge

Supply & fixing factory made plain framed panelled shutters (two or three panels as approved), 35mm thick of 2nd class hard wood (Hollock) with lock rail and panel inserts of 12mm veneered particle board with commercial veneering on both faces or timber flat on both sides (feather edged). The size of rails and styles as per IS-1003 (Part-I), kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401, including 2nd class soft wood kail beading 20mm wide tapering from 10mm to 5mm on one side and also fitted to chowkhat complete all as specified and as directed by Engineer-in- charge. Note : - (i) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item (painting) of BOQ.

Supply & fixing factory made glazed and skeleton shutter, 35mm thick of 2nd class hard wood (Hollock) open rebated (two or three panels as approved) and prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass/wire cloth, etc. Sizes of members as specified in SSR Part-I, Section 8 and fitted to chowkhats, menbers shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and as directed by Engineer-in- charge. Note : - (i) The sutters shall be brought at site without primer and same shall be applying at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item of BOQ. (ii) Glazing or wire cloth shall be measured paid separately under appropriate item of BOQ.

Supply & fixing mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanised wire staples complete all as specified & directed by Engineer-in- charge.

Supply & fixing mild steel barrel tower bolt stove enamelled black with bright bolt 200 mm long, fixed complete all as specified & directed by Engineer-in- charge.

Supply & fixing mild steel sliding door bolts 250mm long, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts washers, four on bolt plate and two on staple plate complete all as specified & directed by Engineer-in- charge.

Supply and fixing in repair 300mm ordinary rat tail rod pattern spring including roller and roller plate and fixing to wooden frame with screw or with welding to metal frame as required complete all as specified and as directed by Engineer-in- charge.

Supply and fixing 300mm ordinary rat tail rod pattern spring including roller and roller plate and fixing to wooden frame with screw or with welding to metal frame as required complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 140mm long (overall length of cover plate ) Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, including sitable screws for fixing complete all as specified and directed by Engineer-in-Charge.

Supply & fixing mild steel pressed handle of size 200mm, oval type, stove enameled black complete all as specified & directed by Engineer-in- charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out 5mm thick plain clour PVC sheet reinforced with MS square tube including painting of edges to match with sheet, all as specified & shown in relevant drawing of item No. 8095 in MES Schedule SSR-2020 (Part-II), fixed in opening using MS screw 75mm long with PVC fastener including making good disturbed wall surfaces (brick, plastering, tiles and painting work as per existing) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made solid core PVC door shutter 30mm thick (stiles) consisting of frame made out of MS tubes of 19mm gauge thickness and size of 19mmx19mm for stiles and for top and bottom rails 15mmx15mm. MS frame shall have a coat of red oxide primer of approved make and shall be covered with heat moulded plain colour PVC sheet, 'C' channel of size 30x50mm forming stiles and 5mm thick wide PVC sheet strip of 20mm width stuck inside with solvent cement for stiles, and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and 10mm (5x2mm) thick, 20mm thick PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beading on either side and joined together with solvent cement adhesive and an additional 5mm thick PVC strips of 20mm width is to be stuck on interior side of C channel using PVC solvent adhesive as per manufacturer's instructions, door to be fixed to frame with and including 3 Nos MS powder coated butt hinges heavy duty of size 75mm long x 25mm wide and 2mm thick and 32mm long steel screws drilled suitable to pass through both the walls of the MS tube complete all as specified in SSR-2009 (Part-I, specifications) & shown in relevant drawing of item No. 8080 in SSR-2020 (Part-II, rates). The width of stiles & rails will be in proportion to the width of the door shutter as specified in SSR-2020 (Part-II). complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 100mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed by Engineer-in-charge.

Supply only 100mm long mild steel butt hinges medium duty complete all as specified & directed by Engineer-in-charge.

Supply and fixing 100mm aluminium handles, cast type, anodised complete all as specified & directed by Engineer-in-charge.

Supply & fixing, factory made steel window confirming to IS 1038 with side hung shutters including projecting type hinges, with steel handle, steel peg stay, complete, dovetailed welded, with glazing bars including fixing of lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast and making good disturbed area of walls and cills to match the existing surfces by bricks / plastering works and painting work etc complete all as specified & as directed by Engineer-in- charge.

Supply & fixing, factory made steel window confirming to IS 1038 with side hung shutters including projecting type hinges, with steel handle, steel peg stay, complete, dovetailed welded, without glazing bars including fixing of lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast and making good disturbed area of walls and cills to match the existing surfces by bricks / plastering works and painting work etc complete all as specified & as directed by Engineer-in- charge.

Supply & fixing, factory made steel ventilators all as per IS 1038/83, with top hung shutters including hinges, suitable steel handle, steel peg stay, fixing lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast and making good disturbed area of walls and cills to match the existing surfces by bricks/plastering works and painting work etc complete all as specified & as directed by Engineer-in- charge.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed by Engineer-in- charge.

Material and labour for Preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed by Engineer-in- charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets fixed in any position with nails fixed with screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing anodised aluminium snap grid frame work of size of grid 605 x605mm for false ceiling including necessary notching and prepared holes, the snap grid shall consist of anodised aluminium main tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/RM, cross and Intermediate tee of size 23.5mm x 26.4mm x 1.4mm weighing 0.191 Kg/RM. The main and cross tee shall be jointed at junction with steel screws or MS bolts, nuts and washers, the snap grid (main / cross tee sections) shall be supported at ends all along the wall with anodised aluminium angle of size 35mm x25mmx 2mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and duly suspended with 6mm GI wire hangers (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including providing 12mm thick gypsum board in grid fixed in false ceiling grid made of aluminium as per above specifications complete all as specified and as directed by Engineer-in-charge.

Material and labour for solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification, complete all as specified & directed by Engineer-in- charge

Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Material and labour for 75mm thick cement concrete ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed by Engineer-in-charge.

Supply and fixing 60 mm thick (M35 grade) precast interlocking tile/paving block factory casted (made by using PVC paver mould / Rubber paver moulds on Vibrating Table Machine) using grey cement and pigment, prepolished & preglazed (any colour as directed), shape haxagon / trigular / zigzag / I-shaped etc, as directed, prepolished & preglazed, specification as per relevant IS, having compressive strength not less than 350 Kg/ Sqcm, laid over sand upto required thick layer and filling the interstices etc complete all as specified and as directed by the Engineer-in-Charge. Note : - (i) Sand for filling shall be measured & paid separately as Supply only but labour for spreding leveling shall be included in the unit rate of this item)

Supply only fine sand without silt (Fazilka/Zera or any other approved sources) for filling under interlocking tiles and the interstices etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC (1:3:6), type C-1 using 20 mm graded stone aggregate as in coping/packing around chequered tiles/interlocking tiles/PCC jalli/chowkhat & similar work etc complete all as specified and as directed by Engineer-in-charge.

Demolition stone/marble slabs/tiles of any description or thickness as in floors/ cooking platform/steps etc. laid bedded and pointed in any mortar including removing rubbish material from the site complete all as specified and as directed by Engineer-in-charge.

Dismantling timber scantlings 40 Sq.cm and over in section, in any position (unframed work), complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge.

Supply and fixing Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick, any colour having tensile strength of 550 Mpa as in ridge (including cutting and bent to shape), roof covering, fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering, complete all as specified and as directed by Engineer-in-charge.

Material and labour for mild steel work tubular poles/post including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to latest relevant IS grade St-240, complete all as specified and as directed by the Engineer-in-Charge.

Repair of steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple, greasing, repair of spring or slidings rails and one shop coat of primer, erected in position as indicated, complete gear operated / chain operated or manual type in any size complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 20 to 25 mm thick, pre polished Kota stone slab (size of slab not less than 550x550mm) as in flooring, laid over and including 15 mm thick bedding layer in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish) and polishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 20 to 25mm thick, Kota stone slab as in riser of steps, skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish ) and polishing by machine, including machine cutting to make it square or rectangular complete all as specified and as directed by Engineer-in-Charge.

M/S SAI BUILDERS

R K GOYAL & COMPANY

AJ. Owners

Singla Enterprises

BALAJI CONSTRUCTIONS

M/S GOYAL BUILDERS

G N CONSTRUCTIONS

SHARDA ENTERPRIES

M/s HANS BROTHERS