Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹14.7 LAccepted-Finance NIWAS BELOW UTTAM GAS AJANCY DISTT SHIMLA | SHIMLA | HIMACHAL PRADESH | 171001 | L1 | Accepted-Finance Lowest | |
| 2 | L2₹15.0 L+₹30,678 (2.08%)Rejected-Finance CHENAB VALLEY DIVISION HPPWD UDAIPUR HIMACHAL PRADESH | CHAMBA | HIMACHAL PRADESH | 176207 | L2 | Rejected-Finance 2nd Lowest | |
| 3 | L3₹15.8 L+₹1.1 L (7.46%)Rejected-Finance | L3 | Rejected-Finance 3rd Lowest | |
| 4 | L4₹15.9 L+₹1.1 L (7.51%)Rejected-Finance | L4 | Rejected-Finance 4th Lowest |
Tender Value
Refer Docs
EMD Value
₹35,000
Closing Date
30 Apr 2026, 10:00 amClosed
Executive Engineer Division Kasumpti HPPWD Shimla-
Executive Engineer Division Kasumpti HPPWD Shimla-3
Construction of W.S platform , P/F water tanks and covering of tank stand , P/F paneling , P/F AI Windows , PVC Flooring in Room no 102, 103 , C/O emergency exit staircase in Directorate of Health Services Block No.- 5 , SDA Complex under Parimahal S
2026_PWD_134793_11
SD-I-CTR-Tender-26- 1383 dated 20-4-26
Open Tender
Civil Works
Percentage
30 days
Shimla
AS per SBD
12 documents required · 12 mandatory
₹500
₹35,000
12 May 2026
21 Apr 2026
30 Apr 2026
21 Apr 2026
30 Apr 2026
21 Apr 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) Hot finished welded type tube ) | 1 | Per Kilogram | - | - |
| 2 | Steel work welded in built up sections, trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafters and the like. | 1 | Per Kilogram. | - | - |
| 3 | Providing and fixing MS welded Mesh 25x25x3mm thick including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. | 1 | Per running Meter | - | - |
| 4Providing and fixing 0.60mm(zero point six zero milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and bitumen washers complete with all accesoriees as required as per the direction of Engineer-in-charge. MAKE TATA Dura Shine | |||||
| 5 | Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping including carriage of materials in all leads as per directions of the Engineer-in-Charge.(i) With white enemal paint. | 1 | Per Square Meter | - | - |
| 6Provdiing and fixing Copper oxidied fitting (iron) (i) Butt hinges 75x47x1.70mm , including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. | |||||
| 7Providing and fixing oxidised M.S sliding door bolts with nuts and screws ets including carriage of mateirals in all leads and lifts as per directions of the Engineer-in-Charge. (i) 250x16mm | |||||
| 8Providing and fixing G.I pipes complete with G.I Fitting including trenching and refilling etc , including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) External work (a) 15mm dia nominal bore . | |||||
| 8.1 | (b) 20 mm dia nominal bore | - | Per running Meter | - | - |
| 9Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end ) (i) 15 mm dia nominal bore, including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. | |||||
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.69 MB
SBD1703861.pdf
Tender Documents • 7.00 MB
BOQ_199532.xls
BOQ • 0.35 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .